Produced by Dianne Bean





A HISTORY OF AERONAUTICS

by E. Charles Vivian




FOREWORD

Although successful heavier-than-air flight is less than two decades
old, and successful dirigible propulsion antedates it by a very short
period, the mass of experiment and accomplishment renders any one-volume
history of the subject a matter of selection. In addition to the
restrictions imposed by space limits, the material for compilation is
fragmentary, and, in many cases, scattered through periodical and
other publications. Hitherto, there has been no attempt at furnishing a
detailed account of how the aeroplane and the dirigible of to-day came
to being, but each author who has treated the subject has devoted his
attention to some special phase or section. The principal exception to
this rule--Hildebrandt--wrote in 1906, and a good many of his statements
are inaccurate, especially with regard to heavier-than-air experiment.

Such statements as are made in this work are, where possible, given
with acknowledgment to the authorities on which they rest. Further
acknowledgment is due to Lieut.-Col. Lockwood Marsh, not only for the
section on aeroplane development which he has contributed to the work,
but also for his kindly assistance and advice in connection with the
section on aerostation. The author's thanks are also due to the
Royal Aeronautical Society for free access to its valuable library of
aeronautical literature, and to Mr A. Vincent Clarke for permission to
make use of his notes on the development of the aero engine.

In this work is no claim to originality--it has been a matter mainly of
compilation, and some stories, notably those of the Wright Brothers and
of Santos Dumont, are better told in the words of the men themselves
than any third party could tell them. The author claims, however, that
this is the first attempt at recording the facts of development and
stating, as fully as is possible in the compass of a single volume, how
flight and aerostation have evolved. The time for a critical history of
the subject is not yet.

In the matter of illustrations, it has been found very difficult to
secure suitable material. Even the official series of photographs of
aeroplanes in the war period is curiously incomplete' and the methods
of censorship during that period prevented any complete series being
privately collected. Omissions in this respect will probably be remedied
in future editions of the work, as fresh material is constantly being
located.

E.C.V. October, 1920.




CONTENTS

     Part I--THE EVOLUTION OF THE AEROPLANE
         I.  THE PERIOD OF LEGEND
        II.  EARLY EXPERIMENTS
       III.  SIR GEORGE CAYLEY--THOMAS WALKER
        IV.  THE MIDDLE NINETEENTH CENTURY
         V.  WENHAM, LE BRIS, AND SOME OTHERS
        VI.  THE AGE OF THE GIANTS
       VII.  LILIENTHAL AND PILCHER
      VIII.  AMERICAN GLIDING EXPERIMENTS
        IX.  NOT PROVEN
         X.  SAMUEL PIERPOINT LANGLEY
        XI.  THE WRIGHT BROTHERS
       XII.  THE FIRST YEARS OF CONQUEST
      XIII.  FIRST FLIERS IN ENGLAND
       XIV.  RHEIMS, AND AFTER
        XV.  THE CHANNEL CROSSING
       XVI.  LONDON TO MANCHESTER
      XVII.  A SUMMARY--TO 1911
     XVIII.  A SUMMARY--TO 1914
       XIX.  THE WAR PERIOD--I
        XX.  THE WAR PERIOD--II
       XXI.  RECONSTRUCTION
      XXII.  1919-1920

     Part II--1903-1920: PROGRESS IN DESIGN
         I.  THE BEGINNINGS
        II.  MULTIPLICITY OF IDEAS
       III.  PROGRESS ON STANDARDISED LINES
        IV.  THE WAR PERIOD

     Part III--AEROSTATICS
         I.  BEGINNINGS
        II.  THE FIRST DIRIGIBLES
       III.  SANTOS-DUMONT
        IV.  THE MILITARY DIRIGIBLE
         V.  BRITISH AIRSHIP  DESIGN
        VI.  THE AIRSHIP  COMMERCIALLY
       VII.  KITE  BALLOONS

     PART IV--ENGINE DEVELOPMENT
         I.  THE VERTICAL TYPE
        II.  THE VEE TYPE
       III.  THE RADIAL TYPE
        IV.  THE ROTARY TYPE
         V.  THE HORIZONTALLY-OPPOSED ENGINE
        VI.  THE TWO-STROKE CYCLE ENGINE
       VII.  ENGINES OF THE WAR  PERIOD

     APPENDICES




PART I. THE EVOLUTION OF THE AEROPLANE




I. THE PERIOD OF LEGEND

The blending of fact and fancy which men call legend reached its fullest
and richest expression in the golden age of Greece, and thus it is to
Greek mythology that one must turn for the best form of any legend which
foreshadows history. Yet the prevalence of legends regarding flight,
existing in the records of practically every race, shows that this form
of transit was a dream of many peoples--man always wanted to fly, and
imagined means of flight.

In this age of steel, a very great part of the inventive genius of man
has gone into devices intended to facilitate transport, both of men and
goods, and the growth of civilisation is in reality the facilitation of
transit, improvement of the means of communication. He was a genius who
first hoisted a sail on a boat and saved the labour of rowing; equally,
he who first harnessed ox or dog or horse to a wheeled vehicle was a
genius--and these looked up, as men have looked up from the earliest
days of all, seeing that the birds had solved the problem of transit far
more completely than themselves. So it must have appeared, and there
is no age in history in which some dreamers have not dreamed of the
conquest of the air; if the caveman had left records, these would
without doubt have showed that he, too, dreamed this dream. His main
aim, probably, was self-preservation; when the dinosaur looked round the
corner, the prehistoric bird got out of the way in his usual manner,
and prehistoric man, such of him as succeeded in getting out of the way
after his fashion--naturally envied the bird, and concluded that as lord
of creation in a doubtful sort of way he ought to have equal
facilities. He may have tried, like Simon the Magician, and other early
experimenters, to improvise those facilities; assuming that he did,
there is the groundwork of much of the older legend with regard to men
who flew, since, when history began, legends would be fashioned out
of attempts and even the desire to fly, these being compounded of some
small ingredient of truth and much exaggeration and addition.

In a study of the first beginnings of the art, it is worth while to
mention even the earliest of the legends and traditions, for they show
the trend of men's minds and the constancy of this dream that has become
reality in the twentieth century. In one of the oldest records of the
world, the Indian classic Mahabarata, it is stated that 'Krishna's
enemies sought the aid of the demons, who built an aerial chariot with
sides of iron and clad with wings. The chariot was driven through the
sky till it stood over Dwarakha, where Krishna's followers dwelt,
and from there it hurled down upon the city missiles that destroyed
everything on which they fell.' Here is pure fable, not legend, but
still a curious forecast of twentieth century bombs from a rigid
dirigible. It is to be noted in this case, as in many, that the power to
fly was an attribute of evil, not of good--it was the demons who built
the chariot, even as at Friedrichshavn. Mediaeval legend in nearly
every case, attributes flight to the aid of evil powers, and incites
well-disposed people to stick to the solid earth--though, curiously
enough, the pioneers of medieval times were very largely of priestly
type, as witness the monk of Malmesbury.

The legends of the dawn of history, however, distribute the power of
flight with less of prejudice. Egyptian sculpture gives the figure
of winged men; the British Museum has made the winged Assyrian bulls
familiar to many, and both the cuneiform records of Assyria and the
hieroglyphs of Egypt record flights that in reality were never made.
The desire fathered the story then, and until Clement Ader either hopped
with his Avion, as is persisted by his critics, or flew, as is claimed
by his friends.

While the origin of many legends is questionable, that of others is
easy enough to trace, though not to prove. Among the credulous the
significance of the name of a people of Asia Minor, the Capnobates,
'those who travel by smoke,' gave rise to the assertion that Montgolfier
was not first in the field--or rather in the air--since surely this
people must have been responsible for the first hot-air balloons. Far
less questionable is the legend of Icarus, for here it is possible
to trace a foundation of fact in the story. Such a tribe as Daedalus
governed could have had hardly any knowledge of the rudiments of
science, and even their ruler, seeing how easy it is for birds to
sustain themselves in the air, might be excused for believing that he,
if he fashioned wings for himself, could use them. In that belief, let
it be assumed, Daedalus made his wings; the boy, Icarus, learning that
his father had determined on an attempt at flight secured the wings and
fastened them to his own shoulders. A cliff seemed the likeliest place
for a 'take-off,' and Icarus leaped from the cliff edge only to find
that the possession of wings was not enough to assure flight to a human
being. The sea that to this day bears his name witnesses that he made
the attempt and perished by it.

In this is assumed the bald story, from which might grow the legend of a
wise king who ruled a peaceful people--'judged, sitting in the sun,' as
Browning has it, and fashioned for himself wings with which he flew over
the sea and where he would, until the prince, Icarus, desired to emulate
him. Icarus, fastening the wings to his shoulders with wax, was so
imprudent as to fly too near the sun, when the wax melted and he fell,
to lie mourned of water-nymphs on the shores of waters thenceforth
Icarian. Between what we have assumed to be the base of fact, and the
legend which has been invested with such poetic grace in Greek story,
there is no more than a century or so of re-telling might give to any
event among a people so simple and yet so given to imagery.

We may set aside as pure fable the stories of the winged horse of
Perseus, and the flights of Hermes as messenger of the gods. With them
may be placed the story of Empedocles, who failed to take Etna seriously
enough, and found himself caught by an eruption while within the crater,
so that, flying to safety in some hurry, he left behind but one sandal
to attest that he had sought refuge in space--in all probability, if
he escaped at all, he flew, but not in the sense that the aeronaut
understands it. But, bearing in mind the many men who tried to fly
in historic times, the legend of Icarus and Daedalus, in spite of the
impossible form in which it is presented, may rank with the story of the
Saracen of Constantinople, or with that of Simon the Magician. A simple
folk would naturally idealise the man and magnify his exploit, as they
magnified the deeds of some strong man to make the legends of Hercules,
and there, full-grown from a mere legend, is the first record of a
pioneer of flying. Such a theory is not nearly so fantastic as that
which makes the Capnobates, on the strength of their name, the inventors
of hot-air balloons. However it may be, both in story and in picture,
Icarus and his less conspicuous father have inspired the Caucasian mind,
and the world is the richer for them.

Of the unsupported myths--unsupported, that is, by even a shadow of
probability--there is no end. Although Latin legend approaches nearer
to fact than the Greek in some cases, in others it shows a disregard
for possibilities which renders it of far less account. Thus Diodorus of
Sicily relates that one Abaris travelled round the world on an arrow of
gold, and Cassiodorus and Glycas and their like told of mechanical birds
that flew and sang and even laid eggs. More credible is the story
of Aulus Gellius, who in his Attic Nights tells how Archytas, four
centuries prior to the opening of the Christian era, made a wooden
pigeon that actually flew by means of a mechanism of balancing weights
and the breath of a mysterious spirit hidden within it. There may yet
arise one credulous enough to state that the mysterious spirit was
precursor of the internal combustion engine, but, however that may be,
the pigeon of Archytas almost certainly existed, and perhaps it actually
glided or flew for short distances--or else Aulus Gellius was an utter
liar, like Cassiodorus and his fellows. In far later times a certain
John Muller, better known as Regiomontanus, is stated to have made an
artificial eagle which accompanied Charles V. on his entry to and exit
from Nuremberg, flying above the royal procession. But, since Muller
died in 1436 and Charles was born in 1500, Muller may be ruled out from
among the pioneers of mechanical flight, and it may be concluded that
the historian of this event got slightly mixed in his dates.

Thus far, we have but indicated how one may draw from the richest
stores from which the Aryan mind draws inspiration, the Greek and Latin
mythologies and poetic adaptations of history. The existing legends of
flight, however, are not thus to be localised, for with two possible
exceptions they belong to all the world and to every civilisation,
however primitive. The two exceptions are the Aztec and the Chinese;
regarding the first of these, the Spanish conquistadores destroyed such
civilisation as existed in Tenochtitlan so thoroughly that, if legend
of flight was among the Aztec records, it went with the rest; as to the
Chinese, it is more than passing strange that they, who claim to have
known and done everything while the first of history was shaping, even
to antedating the discovery of gunpowder that was not made by Roger
Bacon, have not yet set up a claim to successful handling of a monoplane
some four thousand years ago, or at least to the patrol of the Gulf of
Korea and the Mongolian frontier by a forerunner of the 'blimp.'

The Inca civilisation of Peru yields up a myth akin to that of Icarus,
which tells how the chieftain Ayar Utso grew wings and visited the
sun--it was from the sun, too, that the founders of the Peruvian Inca
dynasty, Manco Capac and his wife Mama Huella Capac, flew to earth near
Lake Titicaca, to make the only successful experiment in pure tyranny
that the world has ever witnessed. Teutonic legend gives forth Wieland
the Smith, who made himself a dress with wings and, clad in it, rose
and descended against the wind and in spite of it. Indian mythology, in
addition to the story of the demons and their rigid dirigible, already
quoted, gives the story of Hanouam, who fitted himself with wings by
means of which he sailed in the air and, according to his desire, landed
in the sacred Lauka. Bladud, the ninth king of Britain, is said to have
crowned his feats of wizardry by making himself wings and attempting
to fly--but the effort cost him a broken neck. Bladud may have been as
mythic as Uther, and again he may have been a very early pioneer. The
Finnish epic, 'Kalevala,' tells how Ilmarinen the Smith 'forged an eagle
of fire,' with 'boat's walls between the wings,' after which he 'sat
down on the bird's back and bones,' and flew.

Pure myths, these, telling how the desire to fly was characteristic of
every age and every people, and how, from time to time, there arose an
experimenter bolder than his fellows, who made some attempt to translate
desire into achievement. And the spirit that animated these pioneers,
in a time when things new were accounted things accursed, for the most
part, has found expression in this present century in the utter daring
and disregard of both danger and pain that stamps the flying man, a type
of humanity differing in spirit from his earthbound fellows as fully as
the soldier differs from the priest.

Throughout mediaeval times, records attest that here and there some man
believed in and attempted flight, and at the same time it is clear that
such were regarded as in league with the powers of evil. There is the
half-legend, half-history of Simon the Magician, who, in the third year
of the reign of Nero announced that he would raise himself in the air,
in order to assert his superiority over St Paul. The legend states that
by the aid of certain demons whom he had prevailed on to assist him, he
actually lifted himself in the air--but St Paul prayed him down again.
He slipped through the claws of the demons and fell headlong on the
Forum at Rome, breaking his neck. The 'demons' may have been some
primitive form of hot-air balloon, or a glider with which the magician
attempted to rise into the wind; more probably, however, Simon
threatened to ascend and made the attempt with apparatus as unsuitable
as Bladud's wings, paying the inevitable penalty. Another version of the
story gives St Peter instead of St Paul as the one whose prayers foiled
Simon--apart from the identity of the apostle, the two accounts are
similar, and both define the attitude of the age toward investigation
and experiment in things untried.

Another and later circumstantial story, with similar evidence of some
fact behind it, is that of the Saracen of Constantinople, who, in the
reign of the Emperor Comnenus--some little time before Norman William
made Saxon Harold swear away his crown on the bones of the saints at
Rouen--attempted to fly round the hippodrome at Constantinople, having
Comnenus among the great throng who gathered to witness the feat.
The Saracen chose for his starting-point a tower in the midst of the
hippodrome, and on the top of the tower he stood, clad in a long white
robe which was stiffened with rods so as to spread and catch the breeze,
waiting for a favourable wind to strike on him. The wind was so long in
coming that the spectators grew impatient. 'Fly, O Saracen!' they
called to him. 'Do not keep us waiting so long while you try the wind!'
Comnenus, who had present with him the Sultan of the Turks, gave it
as his opinion that the experiment was both dangerous and vain, and,
possibly in an attempt to controvert such statement, the Saracen leaned
into the wind and 'rose like a bird 'at the outset. But the record of
Cousin, who tells the story in his Histoire de Constantinople, states
that 'the weight of his body having more power to drag him down than his
artificial wings had to sustain him, he broke his bones, and his evil
plight was such that he did not long survive.'

Obviously, the Saracen was anticipating Lilienthal and his gliders by
some centuries; like Simon, a genuine experimenter--both legends
bear the impress of fact supporting them. Contemporary with him, and
belonging to the history rather than the legends of flight, was Oliver,
the monk of Malmesbury, who in the year 1065 made himself wings after
the pattern of those supposed to have been used by Daedalus, attaching
them to his hands and feet and attempting to fly with them. Twysden, in
his Historiae Anglicanae Scriptores X, sets forth the story of Oliver,
who chose a high tower as his starting-point, and launched himself in
the air. As a matter of course, he fell, permanently injuring himself,
and died some time later.

After these, a gap of centuries, filled in by impossible stories of
magical flight by witches, wizards, and the like--imagination was
fertile in the dark ages, but the ban of the church was on all attempt
at scientific development, especially in such a matter as the conquest
of the air. Yet there were observers of nature who argued that since
birds could raise themselves by flapping their wings, man had only to
make suitable wings, flap them, and he too would fly. As early as
the thirteenth century Roger Bacon, the scientific friar of unbounded
inquisitiveness and not a little real genius, announced that there could
be made 'some flying instrument, so that a man sitting in the middle and
turning some mechanism may put in motion some artificial wings which
may beat the air like a bird flying.' But being a cautious man, with a
natural dislike for being burnt at the stake as a necromancer through
having put forward such a dangerous theory, Roger added, 'not that
I ever knew a man who had such an instrument, but I am particularly
acquainted with the man who contrived one.' This might have been a lame
defence if Roger had been brought to trial as addicted to black arts; he
seems to have trusted to the inadmissibility of hearsay evidence.

Some four centuries later there was published a book entitled Perugia
Augusta, written by one C. Crispolti of Perugia--the date of the work in
question is 1648. In it is recorded that 'one day, towards the close of
the fifteenth century, whilst many of the principal gentry had come
to Perugia to honour the wedding of Giovanni Paolo Baglioni, and some
lancers were riding down the street by his palace, Giovanni Baptisti
Danti unexpectedly and by means of a contrivance of wings that he had
constructed proportionate to the size of his body took off from the top
of a tower near by, and with a horrible hissing sound flew successfully
across the great Piazza, which was densely crowded. But (oh, horror of
an unexpected accident!) he had scarcely flown three hundred paces on
his way to a certain point when the mainstay of the left wing gave way,
and, being unable to support himself with the right alone, he fell on a
roof and was injured in consequence. Those who saw not only this flight,
but also the wonderful construction of the framework of the wings,
said--and tradition bears them out--that he several times flew over the
waters of Lake Thrasimene to learn how he might gradually come to earth.
But, notwithstanding his great genius, he never succeeded.'

This reads circumstantially enough, but it may be borne in mind that the
date of writing is more than half a century later than the time of the
alleged achievement--the story had had time to round itself out. Danti,
however, is mentioned by a number of writers, one of whom states that
the failure of his experiment was due to the prayers of some individual
of a conservative turn of mind, who prayed so vigorously that Danti fell
appropriately enough on a church and injured himself to such an extent
as to put an end to his flying career. That Danti experimented, there
is little doubt, in view of the volume of evidence on the point, but the
darkness of the Middle Ages hides the real truth as to the results of
his experiments. If he had actually flown over Thrasimene, as alleged,
then in all probability both Napoleon and Wellington would have had air
scouts at Waterloo.

Danti's story may be taken as fact or left as fable, and with it the
period of legend or vague statement may be said to end--the rest is
history, both of genuine experimenters and of charlatans. Such instances
of legend as are given here are not a tithe of the whole, but there is
sufficient in the actual history of flight to bar out more than this
brief mention of the legends, which, on the whole, go farther to prove
man's desire to fly than his study and endeavour to solve the problems
of the air.




II. EARLY EXPERIMENTS

So far, the stories of the development of flight are either legendary
or of more or less doubtful authenticity, even including that of Danti,
who, although a man of remarkable attainments in more directions
than that of attempted flight, suffers--so far as reputation is
concerned--from the inexactitudes of his chroniclers; he may have soared
over Thrasimene, as stated, or a mere hop with an ineffectual glider may
have grown with the years to a legend of gliding flight. So far, too,
there is no evidence of the study that the conquest of the air demanded;
such men as made experiments either launched themselves in the air from
some height with made-up wings or other apparatus, and paid the penalty,
or else constructed some form of machine which would not leave the
earth, and then gave up. Each man followed his own way, and there was no
attempt--without the printing press and the dissemination of knowledge
there was little possibility of attempt--on the part of any one to
benefit by the failures of others.

Legend and doubtful history carries up to the fifteenth century, and
then came Leonardo da Vinci, first student of flight whose work endures
to the present day. The world knows da Vinci as artist; his age knew him
as architect, engineer, artist, and scientist in an age when science was
a single study, comprising all knowledge from mathematics to medicine.
He was, of course, in league with the devil, for in no other way
could his range of knowledge and observation be explained by his
contemporaries; he left a Treatise on the Flight of Birds in which are
statements and deductions that had to be rediscovered when the Treatise
had been forgotten--da Vinci anticipated modern knowledge as Plato
anticipated modern thought, and blazed the first broad trail toward
flight.

One Cuperus, who wrote a Treatise on the Excellence of Man, asserted
that da Vinci translated his theories into practice, and actually flew,
but the statement is unsupported. That he made models, especially on
the helicopter principle, is past question; these were made of paper and
wire, and actuated by springs of steel wire, which caused them to lift
themselves in the air. It is, however, in the theories which he put
forward that da Vinci's investigations are of greatest interest; these
prove him a patient as well as a keen student of the principles of
flight, and show that his manifold activities did not prevent him from
devoting some lengthy periods to observations of bird flight.

'A bird,' he says in his Treatise, 'is an instrument working according
to mathematical law, which instrument it is within the capacity of man
to reproduce with all its movements, but not with a corresponding
degree of strength, though it is deficient only in power of maintaining
equilibrium. We may say, therefore, that such an instrument constructed
by man is lacking in nothing except the life of the bird, and this life
must needs be supplied from that of man. The life which resides in the
bird's members will, without doubt, better conform to their needs than
will that of a man which is separated from them, and especially in the
almost imperceptible movements which produce equilibrium. But since we
see that the bird is equipped for many apparent varieties of movement,
we are able from this experience to deduce that the most rudimentary
of these movements will be capable of being comprehended by man's
understanding, and that he will to a great extent be able to provide
against the destruction of that instrument of which he himself has
become the living principle and the propeller.'

In this is the definite belief of da Vinci that man is capable of
flight, together with a far more definite statement of the principles by
which flight is to be achieved than any which had preceded it--and for
that matter, than many that have succeeded it. Two further extracts from
his work will show the exactness of his observations:--

'When a bird which is in equilibrium throws the centre of resistance of
the wings behind the centre of gravity, then such a bird will descend
with its head downward. This bird which finds itself in equilibrium
shall have the centre of resistance of the wings more forward than
the bird's centre of gravity; then such a bird will fall with its tail
turned toward the earth.'

And again: 'A man, when flying, shall be free from the waist up, that he
may be able to keep himself in equilibrium as he does in a boat, so
that the centre of his gravity and of the instrument may set itself in
equilibrium and change when necessity requires it to the changing of the
centre of its resistance.'

Here, in this last quotation, are the first beginnings of the inherent
stability which proved so great an advance in design, in this twentieth
century. But the extracts given do not begin to exhaust the range of
da Vinci's observations and deductions. With regard to bird flight, he
observed that so long as a bird keeps its wings outspread it cannot fall
directly to earth, but must glide down at an angle to alight--a small
thing, now that the principle of the plane in opposition to the air is
generally grasped, but da Vinci had to find it out. From observation
he gathered how a bird checks its own speed by opposing tail and wing
surface to the direction of flight, and thus alights at the proper
'landing speed.' He proved the existence of upward air currents by
noting how a bird takes off from level earth with wings outstretched and
motionless, and, in order to get an efficient substitute for the
natural wing, he recommended that there be used something similar to
the membrane of the wing of a bat--from this to the doped fabric of an
aeroplane wing is but a small step, for both are equally impervious to
air. Again, da Vinci recommended that experiments in flight be conducted
at a good height from the ground, since, if equilibrium be lost through
any cause, the height gives time to regain it. This recommendation, by
the way, received ample support in the training areas of war pilots.

Man's muscles, said da Vinci, are fully sufficient to enable him to
fly, for the larger birds, he noted, employ but a small part of their
strength in keeping themselves afloat in the air--by this theory he
attempted to encourage experiment, just as, when his time came, Borelli
reached the opposite conclusion and discouraged it. That Borelli was
right--so far--and da Vinci wrong, detracts not at all from the repute
of the earlier investigator, who had but the resources of his age to
support investigations conducted in the spirit of ages after.

His chief practical contributions to the science of flight--apart
from numerous drawings which have still a value--are the helicopter or
lifting screw, and the parachute. The former, as already noted, he
made and proved effective in model form, and the principle which he
demonstrated is that of the helicopter of to-day, on which sundry
experimenters work spasmodically, in spite of the success of the plane
with its driving propeller. As to the parachute, the idea was doubtless
inspired by observation of the effect a bird produced by pressure of its
wings against the direction of flight.

Da Vinci's conclusions, and his experiments, were forgotten easily by
most of his contemporaries; his Treatise lay forgotten for nearly four
centuries, overshadowed, mayhap, by his other work. There was, however,
a certain Paolo Guidotti of Lucca, who lived in the latter half of the
sixteenth century, and who attempted to carry da Vinci's theories--one
of them, at least, into practice. For this Guidotti, who was by
profession an artist and by inclination an investigator, made for
himself wings, of which the framework was of whalebone; these he covered
with feathers, and with them made a number of gliding flights, attaining
considerable proficiency. He is said in the end to have made a flight of
about four hundred yards, but this attempt at solving the problem
ended on a house roof, where Guidotti broke his thigh bone. After that,
apparently, he gave up the idea of flight, and went back to painting.

One other a Venetian architect named Veranzio, studied da Vinci's theory
of the parachute, and found it correct, if contemporary records and even
pictorial presentment are correct. Da Vinci showed his conception of a
parachute as a sort of inverted square bag; Veranzio modified this to a
'sort of square sail extended by four rods of equal size and having four
cords attached at the corners,' by means of which 'a man could without
danger throw himself from the top of a tower or any high place. For
though at the moment there may be no wind, yet the effort of his falling
will carry up the wind, which the sail will hold, by which means he does
not fall suddenly but descends little by little. The size of the sail
should be measured to the man.' By this last, evidently, Veranzio
intended to convey that the sheet must be of such content as would
enclose sufficient air to support the weight of the parachutist.

Veranzio made his experiments about 1617-1618, but, naturally, they
carried him no farther than the mere descent to earth, and since a
descent is merely a descent, it is to be conjectured that he soon got
tired of dropping from high roofs, and took to designing architecture
instead of putting it to such a use. With the end of his experiments the
work of da Vinci in relation to flying became neglected for nearly four
centuries.

Apart from these two experimenters, there is little to record in the
matter either of experiment or study until the seventeenth century.
Francis Bacon, it is true, wrote about flying in his Sylva Sylvarum, and
mentioned the subject in the New Atlantis, but, except for the insight
that he showed even in superficial mention of any specific subject,
he does not appear to have made attempt at serious investigation.
'Spreading of Feathers, thin and close and in great breadth will
likewise bear up a great Weight,' says Francis, 'being even laid without
Tilting upon the sides.' But a lesser genius could have told as much,
even in that age, and though the great Sir Francis is sometimes adduced
as one of the early students of the problems of flight, his writings
will not sustain the reputation.

The seventeenth century, however, gives us three names, those of
Borelli, Lana, and Robert Hooke, all of which take definite place in
the history of flight. Borelli ranks as one of the great figures in the
study of aeronautical problems, in spite of erroneous deductions through
which he arrived at a purely negative conclusion with regard to the
possibility of human flight.

Borelli was a versatile genius. Born in 1608, he was practically
contemporary with Francesco Lana, and there is evidence that he either
knew or was in correspondence with many prominent members of the Royal
Society of Great Britain, more especially with John Collins, Dr Wallis,
and Henry Oldenburgh, the then Secretary of the Society. He was author
of a long list of scientific essays, two of which only are responsible
for his fame, viz., Theorice Medicaearum Planetarum, published in
Florence, and the better known posthumous De Motu Animalium. The first
of these two is an astronomical study in which Borelli gives evidence of
an instinctive knowledge of gravitation, though no definite expression
is given of this. The second work, De Motu Animalium, deals with the
mechanical action of the limbs of birds and animals and with a theory of
the action of the internal organs. A section of the first part of
this work, called De Volatu, is a study of bird flight; it is quite
independent of Da Vinci's earlier work, which had been forgotten and
remained unnoticed until near on the beginning of practical flight.

Marey, in his work, La Machine Animale, credits Borelli with the first
correct idea of the mechanism of flight. He says: 'Therefore we must be
allowed to render to the genius of Borelli the justice which is due
to him, and only claim for ourselves the merit of having furnished the
experimental demonstration of a truth already suspected.' In fact, all
subsequent studies on this subject concur in making Borelli the first
investigator who illustrated the purely mechanical theory of the action
of a bird's wings.

Borelli's study is divided into a series of propositions in which he
traces the principles of flight, and the mechanical actions of the wings
of birds. The most interesting of these are the propositions in which he
sets forth the method in which birds move their wings during flight and
the manner in which the air offers resistance to the stroke of the wing.
With regard to the first of these two points he says: 'When birds in
repose rest on the earth their wings are folded up close against their
flanks, but when wishing to start on their flight they first bend their
legs and leap into the air. Whereupon the joints of their wings are
straightened out to form a straight line at right angles to the lateral
surface of the breast, so that the two wings, outstretched, are placed,
as it were, like the arms of a cross to the body of the bird. Next,
since the wings with their feathers attached form almost a plane
surface, they are raised slightly above the horizontal, and with a
most quick impulse beat down in a direction almost perpendicular to the
wing-plane, upon the underlying air; and to so intense a beat the air,
notwithstanding it to be fluid, offers resistance, partly by reason
of its natural inertia, which seeks to retain it at rest, and partly
because the particles of the air, compressed by the swiftness of the
stroke, resist this compression by their elasticity, just like the hard
ground. Hence the whole mass of the bird rebounds, making a fresh
leap through the air; whence it follows that flight is simply a motion
composed of successive leaps accomplished through the air. And I remark
that a wing can easily beat the air in a direction almost perpendicular
to its plane surface, although only a single one of the corners of the
humerus bone is attached to the scapula, the whole extent of its base
remaining free and loose, while the greater transverse feathers are
joined to the lateral skin of the thorax. Nevertheless the wing can
easily revolve about its base like unto a fan. Nor are there lacking
tendon ligaments which restrain the feathers and prevent them from
opening farther, in the same fashion that sheets hold in the sails of
ships. No less admirable is nature's cunning in unfolding and folding
the wings upwards, for she folds them not laterally, but by moving
upwards edgewise the osseous parts wherein the roots of the feathers are
inserted; for thus, without encountering the air's resistance the upward
motion of the wing surface is made as with a sword, hence they can be
uplifted with but small force. But thereafter when the wings are twisted
by being drawn transversely and by the resistance of the air, they are
flattened as has been declared and will be made manifest hereafter.'

Then with reference to the resistance to the air of the wings he
explains: 'The air when struck offers resistance by its elastic virtue
through which the particles of the air compressed by the wing-beat
strive to expand again. Through these two causes of resistance the
downward beat of the wing is not only opposed, but even caused to recoil
with a reflex movement; and these two causes of resistance ever increase
the more the down stroke of the wing is maintained and accelerated. On
the other hand, the impulse of the wing is continuously diminished and
weakened by the growing resistance. Hereby the force of the wing and the
resistance become balanced; so that, manifestly, the air is beaten by
the wing with the same force as the resistance to the stroke.'

He concerns himself also with the most difficult problem that confronts
the flying man of to-day, namely, landing effectively, and his remarks
on this subject would be instructive even to an air pilot of these days:
'Now the ways and means by which the speed is slackened at the end of
a flight are these. The bird spreads its wings and tail so that their
concave surfaces are perpendicular to the direction of motion; in this
way, the spreading feathers, like a ship's sail, strike against the
still air, check the speed, and so that most of the impetus may be
stopped, the wings are flapped quickly and strongly forward, inducing a
contrary motion, so that the bird absolutely or very nearly stops.'

At the end of his study Borelli came to a conclusion which militated
greatly against experiment with any heavier-than-air apparatus, until
well on into the nineteenth century, for having gone thoroughly into the
subject of bird flight he states distinctly in his last proposition
on the subject that 'It is impossible that men should be able to fly
craftily by their own strength.' This statement, of course, remains true
up to the present day for no man has yet devised the means by which he
can raise himself in the air and maintain himself there by mere muscular
effort.

From the time of Borelli up to the development of the steam engine it
may be said that flight by means of any heavier-than-air apparatus was
generally regarded as impossible, and apart from certain deductions
which a little experiment would have shown to be doomed to failure, this
method of flight was not followed up. It is not to be wondered at, when
Borelli's exaggerated estimate of the strength expended by birds in
proportion to their weight is borne in mind; he alleged that the motive
force in birds' wings is 10,000 times greater than the resistance of
their weight, and with regard to human flight he remarks:--

'When, therefore, it is asked whether men may be able to fly by their
own strength, it must be seen whether the motive power of the pectoral
muscles (the strength of which is indicated and measured by their size)
is proportionately great, as it is evident that it must exceed the
resistance of the weight of the whole human body 10,000 times, together
with the weight of enormous wings which should be attached to the arms.
And it is clear that the motive power of the pectoral muscles in men is
much less than is necessary for flight, for in birds the bulk and weight
of the muscles for flapping the wings are not less than a sixth part of
the entire weight of the body. Therefore, it would be necessary that
the pectoral muscles of a man should weigh more than a sixth part of the
entire weight of his body; so also the arms, by flapping with the wings
attached, should be able to exert a power 10,000 times greater than the
weight of the human body itself. But they are far below such excess,
for the aforesaid pectoral muscles do not equal a hundredth part of the
entire weight of a man. Wherefore either the strength of the muscles
ought to be increased or the weight of the human body must be decreased,
so that the same proportion obtains in it as exists in birds. Hence
it is deducted that the Icarian invention is entirely mythical because
impossible, for it is not possible either to increase a man's pectoral
muscles or to diminish the weight of the human body; and whatever
apparatus is used, although it is possible to increase the momentum,
the velocity or the power employed can never equal the resistance; and
therefore wing flapping by the contraction of muscles cannot give out
enough power to carry up the heavy body of a man.'

It may be said that practically all the conclusions which Borelli
reached in his study were negative. Although contemporary with Lana,
he perceived the one factor which rendered Lana's project for flight by
means of vacuum globes an impossibility--he saw that no globe could
be constructed sufficiently light for flight, and at the same time
sufficiently strong to withstand the pressure of the outside atmosphere.
He does not appear to have made any experiments in flying on his
own account, having, as he asserts most definitely, no faith in any
invention designed to lift man from the surface of the earth. But his
work, from which only the foregoing short quotations can be given, is,
nevertheless, of indisputable value, for he settled the mechanics of
bird flight, and paved the way for those later investigators who had,
first, the steam engine, and later the internal combustion engine--two
factors in mechanical flight which would have seemed as impossible to
Borelli as would wireless telegraphy to a student of Napoleonic times.
On such foundations as his age afforded Borelli built solidly and
well, so that he ranks as one of the greatest--if not actually the
greatest--of the investigators into this subject before the age of
steam.

The conclusion, that 'the motive force in birds' wings is apparently
ten thousand times greater than the resistance of their weight,' is
erroneous, of course, but study of the translation from which the
foregoing excerpt is taken will show that the error detracts very little
from the value of the work itself. Borelli sets out very definitely
the mechanism of flight, in such fashion that he who runs may read. His
reference to 'the use of a large vessel,' etc., concerns the suggestion
made by Francesco Lana, who antedated Borelli's publication of De Motu
Animalium by some ten years with his suggestion for an 'aerial ship,' as
he called it. Lana's mind shows, as regards flight, a more imaginative
twist; Borelli dived down into first causes, and reached mathematical
conclusions; Lana conceived a theory and upheld it--theoretically, since
the manner of his life precluded experiment.

Francesco Lana, son of a noble family, was born in 1631; in 1647 he was
received as a novice into the Society of Jesus at Rome, and remained
a pious member of the Jesuit society until the end of his life. He was
greatly handicapped in his scientific investigations by the vows
of poverty which the rules of the Order imposed on him. He was more
scientist than priest all his life; for two years he held the post of
Professor of Mathematics at Ferrara, and up to the time of his death,
in 1687, he spent by far the greater part of his time in scientific
research, He had the dubious advantage of living in an age when one man
could cover the whole range of science, and this he seems to have
done very thoroughly. There survives an immense work of his entitled,
Magisterium Naturae et Artis, which embraces the whole field of
scientific knowledge as that was developed in the period in which Lana
lived. In an earlier work of his, published in Brescia in 1670, appears
his famous treatise on the aerial ship, a problem which Lana worked out
with thoroughness. He was unable to make practical experiments, and thus
failed to perceive the one insuperable drawback to his project--of which
more anon.

Only extracts from the translation of Lana's work can be given here, but
sufficient can be given to show fully the means by which he designed to
achieve the conquest of the air. He begins by mention of the celebrated
pigeon of Archytas the Philosopher, and advances one or two theories
with regard to the way in which this mechanical bird was constructed,
and then he recites, apparently with full belief in it, the fable of
Regiomontanus and the eagle that he is said to have constructed to
accompany Charles V. on his entry into Nuremberg. In fact, Lana starts
his work with a study of the pioneers of mechanical flying up to his
own time, and then outlines his own devices for the construction of
mechanical birds before proceeding to detail the construction of the
aerial ship. Concerning primary experiments for this he says:--

'I will, first of all, presuppose that air has weight owing to the
vapours and halations which ascend from the earth and seas to a height
of many miles and surround the whole of our terraqueous globe; and this
fact will not be denied by philosophers, even by those who may have but
a superficial knowledge, because it can be proven by exhausting, if
not all, at any rate the greater part of, the air contained in a glass
vessel, which, if weighed before and after the air has been exhausted,
will be found materially reduced in weight. Then I found out how much
the air weighed in itself in the following manner. I procured a large
vessel of glass, whose neck could be closed or opened by means of a tap,
and holding it open I warmed it over a fire, so that the air inside it
becoming rarified, the major part was forced out; then quickly shutting
the tap to prevent the re-entry I weighed it; which done, I plunged its
neck in water, resting the whole of the vessel on the surface of the
water, then on opening the tap the water rose in the vessel and filled
the greater part of it. I lifted the neck out of the water, released the
water contained in the vessel, and measured and weighed its quantity and
density, by which I inferred that a certain quantity of air had come out
of the vessel equal in bulk to the quantity of water which had entered
to refill the portion abandoned by the air. I again weighed the vessel,
after I had first of all well dried it free of all moisture, and found
it weighed one ounce more whilst it was full of air than when it was
exhausted of the greater part, so that what it weighed more was a
quantity of air equal in volume to the water which took its place. The
water weighed 640 ounces, so I concluded that the weight of air compared
with that of water was 1 to 640--that is to say, as the water which
filled the vessel weighed 640 ounces, so the air which filled the same
vessel weighed one ounce.'

Having thus detailed the method of exhausting air from a vessel, Lana
goes on to assume that any large vessel can be entirely exhausted of
nearly all the air contained therein. Then he takes Euclid's proposition
to the effect that the superficial area of globes increases in the
proportion of the square of the diameter, whilst the volume increases in
the proportion of the cube of the same diameter, and he considers that
if one only constructs the globe of thin metal, of sufficient size, and
exhausts the air in the manner that he suggests, such a globe will be so
far lighter than the surrounding atmosphere that it will not only
rise, but will be capable of lifting weights. Here is Lana's own way of
putting it:--

'But so that it may be enabled to raise heavier weights and to lift
men in the air, let us take double the quantity of copper, 1,232 square
feet, equal to 308 lbs. of copper; with this double quantity of copper
we could construct a vessel of not only double the capacity, but of
four times the capacity of the first, for the reason shown by my fourth
supposition. Consequently the air contained in such a vessel will be 718
lbs. 4 2/3 ounces, so that if the air be drawn out of the vessel it
will be 410 lbs. 4 2/3 ounces lighter than the same volume of air, and,
consequently, will be enabled to lift three men, or at least two, should
they weigh more than eight pesi each. It is thus manifest that the
larger the ball or vessel is made, the thicker and more solid can the
sheets of copper be made, because, although the weight will increase,
the capacity of the vessel will increase to a greater extent and with it
the weight of the air therein, so that it will always be capable to lift
a heavier weight. From this it can be easily seen how it is possible to
construct a machine which, fashioned like unto a ship, will float on the
air.'

With four globes of these dimensions Lana proposed to make an aerial
ship of the fashion shown in his quaint illustration. He is careful to
point out a method by which the supporting globes for the aerial ship
may be entirely emptied of air; (this is to be done by connecting to each
globe a tube of copper which is 'at least a length of 47 modern Roman
palm).' A small tap is to close this tube at the end nearest the globe,
and then vessel and tube are to be filled with water, after which the
tube is to be immersed in water and the tap opened, allowing the water
to run out of the vessel, while no air enters. The tap is then closed
before the lower end of the tube is removed from the water, leaving no
air at all in the globe or sphere. Propulsion of this airship was to be
accomplished by means of sails, and also by oars.

Lana antedated the modern propeller, and realised that the air would
offer enough resistance to oars or paddle to impart motion to any vessel
floating in it and propelled by these means, although he did not realise
the amount of pressure on the air which would be necessary to accomplish
propulsion. As a matter of fact, he foresaw and provided against
practically all the difficulties that would be encountered in the
working, as well as the making, of the aerial ship, finally coming up
against what his religious training made an insuperable objection. This,
again, is best told in his own words:--

'Other difficulties I do not foresee that could prevail against this
invention, save one only, which to me seems the greatest of them all,
and that is that God would surely never allow such a machine to be
successful, since it would create many disturbances in the civil and
political governments of mankind.'

He ends by saying that no city would be proof against surprise, while
the aerial ship could set fire to vessels at sea, and destroy houses,
fortresses, and cities by fire balls and bombs. In fact, at the end of
his treatise on the subject, he furnishes a pretty complete resume of
the activities of German Zeppelins.

As already noted, Lana himself, owing to his vows of poverty, was
unable to do more than put his suggestions on paper, which he did with
a thoroughness that has procured him a place among the really great
pioneers of flying.

It was nearly 200 years before any attempt was made to realise his
project; then, in 1843, M. Marey Monge set out to make the globes and
the ship as Lana detailed them. Monge's experiments cost him the sum
of 25,000 francs 75 centimes, which he expended purely from love
of scientific investigation. He chose to make his globes of brass,
about.004 in thickness, and weighing 1.465 lbs. to the square yard.
Having made his sphere of this metal, he lined it with two thicknesses
of tissue paper, varnished it with oil, and set to work to empty it of
air. This, however, he never achieved, for such metal is incapable of
sustaining the pressure of the outside air, as Lana, had he had the
means to carry out experiments, would have ascertained. M. Monge's
sphere could never be emptied of air sufficiently to rise from the
earth; it ended in the melting-pot, ignominiously enough, and all that
Monge got from his experiment was the value of the scrap metal and the
satisfaction of knowing that Lana's theory could never be translated
into practice.

Robert Hooke is less conspicuous than either Borelli or Lana; his work,
which came into the middle of the seventeenth century, consisted of
various experiments with regard to flight, from which emerged 'a Module,
which by the help of Springs and Wings, raised and sustained itself in
the air.' This must be reckoned as the first model flying machine which
actually flew, except for da Vinci's helicopters; Hooke's model appears
to have been of the flapping-wing type--he attempted to copy the motion
of birds, but found from study and experiment that human muscles were
not sufficient to the task of lifting the human body. For that reason,
he says, 'I applied my mind to contrive a way to make artificial
muscles,' but in this he was, as he expresses it, 'frustrated of my
expectations.' Hooke's claim to fame rests mainly on his successful
model; the rest of his work is of too scrappy a nature to rank as a
serious contribution to the study of flight.

Contemporary with Hooke was one Allard, who, in France, undertook to
emulate the Saracen of Constantinople to a certain extent. Allard was a
tight-rope dancer who either did or was said to have done short gliding
flights--the matter is open to question--and finally stated that he
would, at St Germains, fly from the terrace in the king's presence. He
made the attempt, but merely fell, as did the Saracen some centuries
before, causing himself serious injury. Allard cannot be regarded as a
contributor to the development of aeronautics in any way, and is only
mentioned as typical of the way in which, up to the time of the Wright
brothers, flying was regarded. Even unto this day there are many who
still believe that, with a pair of wings, man ought to be able to fly,
and that the mathematical data necessary to effective construction
simply do not exist. This attitude was reasonable enough in an
unlearned age, and Allard was one--a little more conspicuous than the
majority--among many who made experiment in ignorance, with more or less
danger to themselves and without practical result of any kind.

The seventeenth century was not to end, however, without practical
experiment of a noteworthy kind in gliding flight. Among the recruits to
the ranks of pioneers was a certain Besnier, a locksmith of Sable, who
somewhere between 1675 and 1680 constructed a glider of which a crude
picture has come down to modern times. The apparatus, as will be seen,
consisted of two rods with hinged flaps, and the original designer of
the picture seems to have had but a small space in which to draw, since
obviously the flaps must have been much larger than those shown. Besnier
placed the rods on his shoulders, and worked the flaps by cords attached
to his hands and feet--the flaps opened as they fell, and closed as they
rose, so the device as a whole must be regarded as a sort of flapping
glider. Having by experiment proved his apparatus successful, Besnier
promptly sold it to a travelling showman of the period, and forthwith
set about constructing a second set, with which he made gliding flights
of considerable height and distance. Like Lilienthal, Besnier projected
himself into space from some height, and then, according to the
contemporary records, he was able to cross a river of considerable size
before coming to earth. It does not appear that he had any imitators,
or that any advantage whatever was taken of his experiments; the age was
one in which he would be regarded rather as a freak exhibitor than as
a serious student, and possibly, considering his origin and the sale of
his first apparatus to such a client, he regarded the matter himself as
more in the nature of an amusement than as a discovery.

Borelli, coming at the end of the century, proved to his own
satisfaction and that of his fellows that flapping wing flight was an
impossibility; the capabilities of the plane were as yet undreamed, and
the prime mover that should make the plane available for flight was
deep in the womb of time. Da Vinci's work was forgotten--flight was an
impossibility, or at best such a useless show as Besnier was able to
give.

The eighteenth century was almost barren of experiment. Emanuel
Swedenborg, having invented a new religion, set about inventing a flying
machine, and succeeded theoretically, publishing the result of his
investigations as follows:--

'Let a car or boat or some like object be made of light material such as
cork or bark, with a room within it for the operator. Secondly, in front
as well as behind, or all round, set a widely-stretched sail parallel to
the machine forming within a hollow or bend which could be reefed like
the sails of a ship. Thirdly, place wings on the sides, to be worked
up and down by a spiral spring, these wings also to be hollow below in
order to increase the force and velocity, take in the air, and make the
resistance as great as may be required. These, too, should be of light
material and of sufficient size; they should be in the shape of birds'
wings, or the sails of a windmill, or some such shape, and should be
tilted obliquely upwards, and made so as to collapse on the upward
stroke and expand on the downward. Fourth, place a balance or beam
below, hanging down perpendicularly for some distance with a small
weight attached to its end, pendent exactly in line with the centre of
gravity; the longer this beam is, the lighter must it be, for it must
have the same proportion as the well-known vectis or steel-yard. This
would serve to restore the balance of the machine if it should lean over
to any of the four sides. Fifthly, the wings would perhaps have greater
force, so as to increase the resistance and make the flight easier, if
a hood or shield were placed over them, as is the case with certain
insects. Sixthly, when the sails are expanded so as to occupy a great
surface and much air, with a balance keeping them horizontal, only a
small force would be needed to move the machine back and forth in a
circle, and up and down. And, after it has gained momentum to move
slowly upwards, a slight movement and an even bearing would keep it
balanced in the air and would determine its direction at will.'

The only point in this worthy of any note is the first device for
maintaining stability automatically--Swedenborg certainly scored a point
there. For the rest, his theory was but theory, incapable of being put
to practice--he does not appear to have made any attempt at advance
beyond the mere suggestion.

Some ten years before his time the state of knowledge with regard to
flying in Europe was demonstrated by an order granted by the King of
Portugal to Friar Lourenzo de Guzman, who claimed to have invented a
flying machine capable of actual flight. The order stated that 'In
order to encourage the suppliant to apply himself with zeal toward
the improvement of the new machine, which is capable of producing the
effects mentioned by him, I grant unto him the first vacant place in
my College of Barcelos or Santarem, and the first professorship of
mathematics in my University of Coimbra, with the annual pension of
600,000 reis during his life.--Lisbon, 17th of March, 1709.'

What happened to Guzman when the non-existence of the machine was
discovered is one of the things that is well outside the province of
aeronautics. He was charlatan pure and simple, as far as actual flight
was concerned, though he had some ideas respecting the design of hot-air
balloons, according to Tissandier. (La Navigation Aerienne.) His
flying machine was to contain, among other devices, bellows to produce
artificial wind when the real article failed, and also magnets in globes
to draw the vessel in an upward direction and maintain its buoyancy.
Some draughtsman, apparently gifted with as vivid imagination as Guzman
himself, has given to the world an illustration of the hypothetical
vessel; it bears some resemblance to Lana's aerial ship, from which fact
one draws obvious conclusions.

A rather amusing claim to solving the problem of flight was made in the
middle of the eighteenth century by one Grimaldi, a 'famous and unique
Engineer' who, as a matter of actual fact, spent twenty years in
missionary work in India, and employed the spare time that missionary
work left him in bringing his invention to a workable state. The
invention is described as a 'box which with the aid of clockwork rises
in the air, and goes with such lightness and strong rapidity that it
succeeds in flying a journey of seven leagues in an hour. It is made in
the fashion of a bird; the wings from end to end are 25 feet in extent.
The body is composed of cork, artistically joined together and well
fastened with metal wire, covered with parchment and feathers. The
wings are made of catgut and whalebone, and covered also with the same
parchment and feathers, and each wing is folded in three seams. In the
body of the machine are contained thirty wheels of unique work, with two
brass globes and little chains which alternately wind up a counterpoise;
with the aid of six brass vases, full of a certain quantity of
quicksilver, which run in some pulleys, the machine is kept by the
artist in due equilibrium and balance. By means, then, of the friction
between a steel wheel adequately tempered and a very heavy and
surprising piece of lodestone, the whole is kept in a regulated forward
movement, given, however, a right state of the winds, since the machine
cannot fly so much in totally calm weather as in stormy. This prodigious
machine is directed and guided by a tail seven palmi long, which is
attached to the knees and ankles of the inventor by leather straps; by
stretching out his legs, either to the right or to the left, he moves
the machine in whichever direction he pleases.... The machine's
flight lasts only three hours, after which the wings gradually close
themselves, when the inventor, perceiving this, goes down gently, so as
to get on his own feet, and then winds up the clockwork and gets himself
ready again upon the wings for the continuation of a new flight. He
himself told us that if by chance one of the wheels came off or if one
of the wings broke, it is certain he would inevitably fall rapidly to
the ground, and, therefore, he does not rise more than the height of a
tree or two, as also he only once put himself in the risk of crossing
the sea, and that was from Calais to Dover, and the same morning he
arrived in London.'

And yet there are still quite a number of people who persist in stating
that Bleriot was the first man to fly across the Channel!

A study of the development of the helicopter principle was published
in France in 1868, when the great French engineer Paucton produced his
Theorie de la Vis d'Archimede. For some inexplicable reason, Paucton
was not satisfied with the term 'helicopter,' but preferred to call it
a 'pterophore,' a name which, so far as can be ascertained, has not been
adopted by any other writer or investigator. Paucton stated that, since
a man is capable of sufficient force to overcome the weight of his own
body, it is only necessary to give him a machine which acts on the air
'with all the force of which it is capable and at its utmost speed,' and
he will then be able to lift himself in the air, just as by the exertion
of all his strength he is able to lift himself in water. 'It would
seem,' says Paucton, 'that in the pterophore, attached vertically to a
carriage, the whole built lightly and carefully assembled, he has
found something that will give him this result in all perfection. In
construction, one would be careful that the machine produced the least
friction possible, and naturally it ought to produce little, as it would
not be at all complicated. The new Daedalus, sitting comfortably in his
carriage, would by means of a crank give to the pterophore a suitable
circular (or revolving) speed. This single pterophore would lift him
vertically, but in order to move horizontally he should be supplied with
a tail in the shape of another pterophore. When he wished to stop for a
little time, valves fixed firmly across the end of the space between
the blades would automatically close the openings through which the air
flows, and change the pterophore into an unbroken surface which
would resist the flow of air and retard the fall of the machine to a
considerable degree.'

The doctrine thus set forth might appear plausible, but it is based on
the common misconception that all the force which might be put into the
helicopter or 'pterophore' would be utilised for lifting or propelling
the vehicle through the air, just as a propeller uses all its power to
drive a ship through water. But, in applying such a propelling force
to the air, most of the force is utilised in maintaining aerodynamic
support--as a matter of fact, more force is needed to maintain this
support than the muscle of man could possibly furnish to a lifting
screw, and even if the helicopter were applied to a full-sized,
engine-driven air vehicle, the rate of ascent would depend on the amount
of surplus power that could be carried. For example, an upward lift
of 1,000 pounds from a propeller 15 feet in diameter would demand an
expenditure of 50 horse-power under the best possible conditions, and in
order to lift this load vertically through such atmospheric pressure as
exists at sea-level or thereabouts, an additional 20 horsepower would be
required to attain a rate of 11 feet per second--50 horse-power must
be continually provided for the mere support of the load, and the
additional 20 horse-power must be continually provided in order to
lift it. Although, in model form, there is nothing quite so strikingly
successful as the helicopter in the range of flying machines, yet the
essential weight increases so disproportionately to the effective area
that it is necessary to go but very little beyond model dimensions for
the helicopter to become quite ineffective.

That is not to say that the lifting screw must be totally ruled out
so far as the construction of aircraft is concerned. Much is still
empirical, so far as this branch of aeronautics is concerned, and
consideration of the structural features of a propeller goes to show
that the relations of essential weight and effective area do not
altogether apply in practice as they stand in theory. Paucton's dream,
in some modified form, may yet become reality--it is only so short
a time ago as 1896 that Lord Kelvin stated he had not the smallest
molecule of faith in aerial navigation, and since the whole history of
flight consists in proving the impossible possible, the helicopter may
yet challenge the propelled plane surface for aerial supremacy.

It does not appear that Paucton went beyond theory, nor is there in his
theory any advance toward practical flight--da Vinci could have told
him as much as he knew. He was followed by Meerwein, who invented an
apparatus apparently something between a flapping wing machine and a
glider, consisting of two wings, which were to be operated by means of a
rod; the venturesome one who would fly by means of this apparatus had to
lie in a horizontal position beneath the wings to work the rod. Meerwein
deserves a place of mention, however, by reason of his investigations
into the amount of surface necessary to support a given weight. Taking
that weight at 200 pounds--which would allow for the weight of a man
and a very light apparatus--he estimated that 126 square feet would be
necessary for support. His pamphlet, published at Basle in 1784, shows
him to have been a painstaking student of the potentialities of flight.

Jean-Pierre Blanchard, later to acquire fame in connection with balloon
flight, conceived and described a curious vehicle, of which he even
announced trials as impending. His trials were postponed time after
time, and it appears that he became convinced in the end of the futility
of his device, being assisted to such a conclusion by Lalande, the
astronomer, who repeated Borelli's statement that it was impossible for
man ever to fly by his own strength. This was in the closing days of
the French monarchy, and the ascent of the Montgolfiers' first hot-air
balloon in 1783--which shall be told more fully in its place--put an
end to all French experiments with heavier-than-air apparatus, though in
England the genius of Cayley was about to bud, and even in France there
were those who understood that ballooning was not true flight.




III. SIR GEORGE CAYLEY--THOMAS WALKER

On the fifth of June, 1783, the Montgolfiers' hot-air balloon rose at
Versailles, and in its rising divided the study of the conquest of the
air into two definite parts, the one being concerned with the
propulsion of gas lifted, lighter-than-air vehicles, and the other being
crystallised in one sentence by Sir George Cayley: 'The whole problem,'
he stated, 'is confined within these limits, viz.: to make a surface
support a given weight by the application of power to the resistance of
the air.' For about ten years the balloon held the field entirely, being
regarded as the only solution of the problem of flight that man could
ever compass. So definite for a time was this view on the eastern side
of the Channel that for some years practically all the progress that was
made in the development of power-driven planes was made in Britain.

In 1800 a certain Dr Thomas Young demonstrated that certain curved
surfaces suspended by a thread moved into and not away from a horizontal
current of air, but the demonstration, which approaches perilously near
to perpetual motion if the current be truly horizontal, has never been
successfully repeated, so that there is more than a suspicion that
Young's air-current was NOT horizontal. Others had made and were making
experiments on the resistance offered to the air by flat surfaces, when
Cayley came to study and record, earning such a place among the pioneers
as to win the title of 'father of British aeronautics.'

Cayley was a man in advance of his time, in many ways. Of independent
means, he made the grand tour which was considered necessary to the
education of every young man of position, and during this excursion he
was more engaged in studies of a semi-scientific character than in the
pursuits that normally filled such a period. His various writings prove
that throughout his life aeronautics was the foremost subject in his
mind; the Mechanic's Magazine, Nicholson's Journal, the Philosophical
Magazine, and other periodicals of like nature bear witness to Cayley's
continued research into the subject of flight. He approached the subject
after the manner of the trained scientist, analysing the mechanical
properties of air under chemical and physical action. Then he set to
work to ascertain the power necessary for aerial flight, and was one of
the first to enunciate the fallacy of the hopes of successful flight by
means of the steam engine of those days, owing to the fact that it was
impossible to obtain a given power with a given weight.

Yet his conclusions on this point were not altogether negative, for as
early as 1810 he stated that he could construct a balloon which could
travel with passengers at 20 miles an hour--he was one of the first to
consider the possibilities of applying power to a balloon. Nearly thirty
years later--in 1837--he made the first attempt at establishing an
aeronautical society, but at that time the power-driven plane was
regarded by the great majority as an absurd dream of more or less mad
inventors, while ballooning ranked on about the same level as tight-rope
walking, being considered an adjunct to fairs and fetes, more a pastime
than a study.

Up to the time of his death, in 1857, Cayley maintained his study of
aeronautical matters, and there is no doubt whatever that his work
went far in assisting the solution of the problem of air conquest. His
principal published work, a monograph entitled Aerial Navigation, has
been republished in the admirable series of 'Aeronautical Classics'
issued by the Royal Aeronautical Society. He began this work by
pointing out the impossibility of flying by means of attached wings, an
impossibility due to the fact that, while the pectoral muscles of a bird
account for more than two-thirds of its whole muscular strength, in a
man the muscles available for flying, no matter what mechanism might be
used, would not exceed one-tenth of his total strength.

Cayley did not actually deny the possibility of a man flying by muscular
effort, however, but stated that 'the flight of a strong man by great
muscular exertion, though a curious and interesting circumstance,
inasmuch as it will probably be the means of ascertaining finis power
and supplying the basis whereon to improve it, would be of little use.'

From this he goes on to the possibility of using a Boulton and Watt
steam engine to develop the power necessary for flight, and in this he
saw a possibility of practical result. It is worthy of note that in
this connection he made mention of the forerunner of the modern internal
combustion engine; 'The French,' he said, 'have lately shown the great
power produced by igniting inflammable powders in closed vessels,
and several years ago an engine was made to work in this country in
a similar manner by inflammation of spirit of tar.' In a subsequent
paragraph of his monograph he anticipates almost exactly the
construction of the Lenoir gas engine, which came into being more than
fifty-five years after his monograph was published.

Certain experiments detailed in his work were made to ascertain the
size of the surface necessary for the support of any given weight.
He accepted a truism of to-day in pointing out that in any matters
connected with aerial investigation, theory and practice are as
widely apart as the poles. Inclined at first to favour the helicopter
principle, he finally rejected this in favour of the plane, with which
he made numerous experiments. During these, he ascertained the peculiar
advantages of curved surfaces, and saw the necessity of providing both
vertical and horizontal rudders in order to admit of side steering
as well as the control of ascent and descent, and for preserving
equilibrium. He may be said to have anticipated the work of Lilienthal
and Pilcher, since he constructed and experimented with a fixed surface
glider. 'It was beautiful,' he wrote concerning this, 'to see this noble
white bird sailing majestically from the top of a hill to any given
point of the plain below it with perfect steadiness and safety,
according to the set of its rudder, merely by its own weight, descending
at an angle of about eight degrees with the horizon.'

It is said that he once persuaded his gardener to trust himself in this
glider for a flight, but if Cayley himself ventured a flight in it he
has left no record of the fact. The following extract from his work,
Aerial Navigation, affords an instance of the thoroughness of his
investigations, and the concluding paragraph also shows his faith in the
ultimate triumph of mankind in the matter of aerial flight:--

'The act of flying requires less exertion than from the appearance is
supposed. Not having sufficient data to ascertain the exact degree of
propelling power exerted by birds in the act of flying, it is uncertain
what degree of energy may be required in this respect for vessels of
aerial navigation; yet when we consider the many hundreds of miles of
continued flight exerted by birds of passage, the idea of its being only
a small effort is greatly corroborated. To apply the power of the first
mover to the greatest advantage in producing this effect is a very
material point. The mode universally adopted by Nature is the oblique
waft of the wing. We have only to choose between the direct beat
overtaking the velocity of the current, like the oar of a boat, or
one applied like the wing, in some assigned degree of obliquity to it.
Suppose 35 feet per second to be the velocity of an aerial vehicle, the
oar must be moved with this speed previous to its being able to receive
any resistance; then if it be only required to obtain a pressure of
one-tenth of a lb. upon each square foot it must exceed the velocity of
the current 7.3 feet per second. Hence its whole velocity must be 42.5
feet per second. Should the same surface be wafted downward like a wing
with the hinder edge inclined upward in an angle of about 50 deg. 40
feet to the current it will overtake it at a velocity of 3.5 feet per
second; and as a slight unknown angle of resistance generates a lb.
pressure per square foot at this velocity, probably a waft of a little
more than 4 feet per second would produce this effect, one-tenth part
of which would be the propelling power. The advantage of this mode of
application compared with the former is rather more than ten to one.

'In continuing the general principles of aerial navigation, for the
practice of the art, many mechanical difficulties present themselves
which require a considerable course of skilfully applied experiments
before they can be overcome; but, to a certain extent, the air has
already been made navigable, and no one who has seen the steadiness
with which weights to the amount of ten stone (including four stone,
the weight of the machine) hover in the air can doubt of the ultimate
accomplishment of this object.'

This extract from his work gives but a faint idea of the amount of
research for which Cayley was responsible. He had the humility of the
true investigator in scientific problems, and so far as can be seen
was never guilty of the great fault of so many investigators in this
subject--that of making claims which he could not support. He was
content to do, and pass after having recorded his part, and although
nearly half a century had to pass between the time of his death and the
first actual flight by means of power-driven planes, yet he may be said
to have contributed very largely to the solution of the problem, and his
name will always rank high in the roll of the pioneers of flight.

Practically contemporary with Cayley was Thomas Walker, concerning whom
little is known save that he was a portrait painter of Hull, where
was published his pamphlet on The Art of Flying in 1810, a second and
amplified edition being produced, also in Hull, in 1831. The pamphlet,
which has been reproduced in extenso in the Aeronautical Classics series
published by the Royal Aeronautical Society, displays a curious mixture
of the true scientific spirit and colossal conceit. Walker appears to
have been a man inclined to jump to conclusions, which carried him up to
the edge of discovery and left him vacillating there.

The study of the two editions of his pamphlet side by side shows that
their author made considerable advances in the practicability of his
designs in the 21 intervening years, though the drawings which accompany
the text in both editions fail to show anything really capable
of flight. The great point about Walker's work as a whole is its
suggestiveness; he did not hesitate to state that the 'art' of flying is
as truly mechanical as that of rowing a boat, and he had some conception
of the necessary mechanism, together with an absolute conviction that he
knew all there was to be known. 'Encouraged by the public,' he says,
'I would not abandon my purpose of making still further exertions to
advance and complete an art, the discovery of the TRUE PRINCIPLES (the
italics are Walker's own) of which, I trust, I can with certainty affirm
to be my own.'

The pamphlet begins with Walker's admiration of the mechanism of flight
as displayed by birds. 'It is now almost twenty years,' he says, 'since
I was first led to think, by the study of birds and their means of
flying, that if an artificial machine were formed with wings in exact
imitation of the mechanism of one of those beautiful living machines,
and applied in the very same way upon the air, there could be no doubt
of its being made to fly, for it is an axiom in philosophy that the same
cause will ever produce the same effect.' With this he confesses his
inability to produce the said effect through lack of funds, though he
clothes this delicately in the phrase 'professional avocations and other
circumstances.' Owing to this inability he published his designs that
others might take advantage of them, prefacing his own researches with
a list of the very early pioneers, and giving special mention to
Friar Bacon, Bishop Wilkins, and the Portuguese friar, De Guzman. But,
although he seems to suggest that others should avail themselves of
his theoretical knowledge, there is a curious incompleteness about the
designs accompanying his work, and about the work itself, which seems
to suggest that he had more knowledge to impart than he chose to make
public--or else that he came very near to complete solution of the
problem of flight, and stayed on the threshold without knowing it.

After a dissertation upon the history and strength of the condor, and
on the differences between the weights of birds, he says: 'The following
observations upon the wonderful difference in the weight of some birds,
with their apparent means of supporting it in their flight, may tend
to remove some prejudices against my plan from the minds of some of
my readers. The weight of the humming-bird is one drachm, that of the
condor not less than four stone. Now, if we reduce four stone into
drachms we shall find the condor is 14,336 times as heavy as the
humming-bird. What an amazing disproportion of weight! Yet by the same
mechanical use of its wings the condor can overcome the specific gravity
of its body with as much ease as the little humming-bird. But this is
not all. We are informed that this enormous bird possesses a power in
its wings, so far exceeding what is necessary for its own conveyance
through the air, that it can take up and fly away with a whole sheer in
its talons, with as much ease as an eagle would carry off, in the same
manner, a hare or a rabbit. This we may readily give credit to, from the
known fact of our little kestrel and the sparrow-hawk frequently flying
off with a partridge, which is nearly three times the weight of these
rapacious little birds.'

After a few more observations he arrives at the following conclusion:
'By attending to the progressive increase in the weight of birds, from
the delicate little humming-bird up to the huge condor, we clearly
discover that the addition of a few ounces, pounds, or stones, is no
obstacle to the art of flying; the specific weight of birds avails
nothing, for by their possessing wings large enough, and sufficient
power to work them, they can accomplish the means of flying equally well
upon all the various scales and dimensions which we see in nature. Such
being a fact, in the name of reason and philosophy why shall not man,
with a pair of artificial wings, large enough, and with sufficient power
to strike them upon the air, be able to produce the same effect?'

Walker asserted definitely and with good ground that muscular effort
applied without mechanism is insufficient for human flight, but he
states that if an aeronautical boat were constructed so that a man could
sit in it in the same manner as when rowing, such a man would be able to
bring into play his whole bodily strength for the purpose of flight,
and at the same time would be able to get an additional advantage by
exerting his strength upon a lever. At first he concluded there must
be expansion of wings large enough to resist in a sufficient degree
the specific gravity of whatever is attached to them, but in the second
edition of his work he altered this to 'expansion of flat passive
surfaces large enough to reduce the force of gravity so as to float
the machine upon the air with the man in it.' The second requisite is
strength enough to strike the wings with sufficient force to complete
the buoyancy and give a projectile motion to the machine. Given
these two requisites, Walker states definitely that flying must be
accomplished simply by muscular exertion. 'If we are secure of these two
requisites, and I am very confident we are, we may calculate upon the
success of flight with as much certainty as upon our walking.'

Walker appears to have gained some confidence from the experiments of a
certain M. Degen, a watchmaker of Vienna, who, according to the Monthly
Magazine of September, 1809, invented a machine by means of which a
person might raise himself into the air. The said machine, according to
the magazine, was formed of two parachutes which might be folded up or
extended at pleasure, while the person who worked them was placed in the
centre. This account, however, was rather misleading, for the magazine
carefully avoided mention of a balloon to which the inventor fixed his
wings or parachutes. Walker, knowing nothing of the balloon, concluded
that Degen actually raised himself in the air, though he is doubtful
of the assertion that Degen managed to fly in various directions,
especially against the wind.

Walker, after considering Degen and all his works, proceeds to detail
his own directions for the construction of a flying machine, these
being as follows: 'Make a car of as light material as possible, but
with sufficient strength to support a man in it; provide a pair of wings
about four feet each in length; let them be horizontally expanded and
fastened upon the top edge of each side of the car, with two joints
each, so as to admit of a vertical motion to the wings, which motion may
be effected by a man sitting and working an upright lever in the middle
of the car. Extend in the front of the car a flat surface of silk, which
must be stretched out and kept fixed in a passive state; there must
be the same fixed behind the car; these two surfaces must be perfectly
equal in length and breadth and large enough to cover a sufficient
quantity of air to support the whole weight as nearly in equilibrium as
possible, thus we shall have a great sustaining power in those passive
surfaces and the active wings will propel the car forward.'

A description of how to launch this car is subsequently given: 'It
becomes necessary,' says the theorist, 'that I should give directions
how it may be launched upon the air, which may be done by various means;
perhaps the following method may be found to answer as well as any: Fix
a poll upright in the earth, about twenty feet in height, with two open
collars to admit another poll to slide upwards through them; let there
be a sliding platform made fast upon the top of the sliding poll; place
the car with a man in it upon the platform, then raise the platform to
the height of about thirty feet by means of the sliding poll, let the
sliding poll and platform suddenly fall down, the car will then be
left upon the air, and by its pressing the air a projectile force will
instantly propel the car forward; the man in the car must then strike
the active wings briskly upon the air, which will so increase the
projectile force as to become superior to the force of gravitation, and
if he inclines his weight a little backward, the projectile impulse will
drive the car forward in an ascending direction. When the car is brought
to a sufficient altitude to clear the tops of hills, trees, buildings,
etc., the man, by sitting a little forward on his seat, will then bring
the wings upon a horizontal plane, and by continuing the action of the
wings he will be impelled forward in that direction. To descend, he
must desist from striking the wings, and hold them on a level with their
joints; the car will then gradually come down, and when it is within
five or six feet of the ground the man must instantly strike the wings
downwards, and sit as far back as he can; he will by this means check
the projectile force, and cause the car to alight very gently with a
retrograde motion. The car, when up in the air, may be made to turn
to the right or to the left by forcing out one of the fins, having one
about eighteen inches long placed vertically on each side of the car for
that purpose, or perhaps merely by the man inclining the weight of his
body to one side.'

Having stated how the thing is to be done, Walker is careful to explain
that when it is done there will be in it some practical use, notably in
respect of the conveyance of mails and newspapers, or the saving of
life at sea, or for exploration, etc. It might even reduce the number of
horses kept by man for his use, by means of which a large amount of land
might be set free for the growth of food for human consumption.

At the end of his work Walker admits the idea of steam power for driving
a flying machine in place of simple human exertion, but he, like Cayley,
saw a drawback to this in the weight of the necessary engine. On the
whole, he concluded, navigation of the air by means of engine power
would be mostly confined to the construction of navigable balloons.

As already noted, Walker's work is not over practical, and the foregoing
extract includes the most practical part of it; the rest is a series
of dissertations on bird flight, in which, evidently, the portrait
painter's observations were far less thorough than those of da Vinci or
Borelli. Taken on the whole, Walker was a man with a hobby; he devoted
to it much time and thought, but it remained a hobby, nevertheless. His
observations have proved useful enough to give him a place among the
early students of flight, but a great drawback to his work is the lack
of practical experiment, by means of which alone real advance could
be made; for, as Cayley admitted, theory and practice are very widely
separated in the study of aviation, and the whole history of flight is
a matter of unexpected results arising from scarcely foreseen causes,
together with experiment as patient as daring.




IV. THE MIDDLE NINETEENTH CENTURY

Both Cayley and Walker were theorists, though Cayley supported his
theoretical work with enough of practice to show that he studied along
right lines; a little after his time there came practical men
who brought to being the first machine which actually flew by the
application of power. Before their time, however, mention must be made
of the work of George Pocock of Bristol, who, somewhere about 1840
invented what was described as a 'kite carriage,' a vehicle which
carried a number of persons, and obtained its motive power from a large
kite. It is on record that, in the year 1846 one of these carriages
conveyed sixteen people from Bristol to London. Another device of
Pocock's was what he called a 'buoyant sail,' which was in effect a
man-lifting kite, and by means of which a passenger was actually raised
100 yards from the ground, while the inventor's son scaled a cliff
200 feet in height by means of one of these, 'buoyant sails.' This
constitutes the first definitely recorded experiment in the use of
man-lifting kites. A History of the Charvolant or Kite-carriage,
published in London in 1851, states that 'an experiment of a bold and
very novel character was made upon an extensive down, where a large
wagon with a considerable load was drawn along, whilst this huge machine
at the same time carried an observer aloft in the air, realising almost
the romance of flying.'

Experimenting, two years after the appearance of the 'kite-carriage,'
on the helicopter principle, W. H. Phillips constructed a model machine
which weighed two pounds; this was fitted with revolving fans, driven
by the combustion of charcoal, nitre, and gypsum, producing steam which,
discharging into the air, caused the fans to revolve. The inventor
stated that 'all being arranged, the steam was up in a few seconds, when
the whole apparatus spun around like any top, and mounted into the
air faster than a bird; to what height it ascended I had no means of
ascertaining; the distance travelled was across two fields, where, after
a long search, I found the machine minus the wings, which had been
torn off in contact with the ground.' This could hardly be described as
successful flight, but it was an advance in the construction of machines
on the helicopter principle, and it was the first steam-driven model of
the type which actually flew. The invention, however, was not followed
up.

After Phillips, we come to the great figures of the middle nineteenth
century, W. S. Henson and John Stringfellow. Cayley had shown, in
1809, how success might be attained by developing the idea of the plane
surface so driven as to take advantage of the resistance offered by
the air, and Henson, who as early as 1840 was experimenting with model
gliders and light steam engines, evolved and patented an idea for
something very nearly resembling the monoplane of the early twentieth
century. His patent, No. 9478, of the year 1842 explains the principle
of the machine as follows:--

In order that the description hereafter given be rendered clear, I will
first shortly explain the principle on which the machine is constructed.
If any light and flat or nearly flat article be projected or thrown
edgewise in a slightly inclined position, the same will rise on the
air till the force exerted is expended, when the article so thrown or
projected will descend; and it will readily be conceived that, if the
article so projected or thrown possessed in itself a continuous power or
force equal to that used in throwing or projecting it, the article
would continue to ascend so long as the forward part of the surface was
upwards in respect to the hinder part, and that such article, when the
power was stopped, or when the inclination was reversed, would descend
by gravity aided by the force of the power contained in the article, if
the power be continued, thus imitating the flight of a bird.

Now, the first part of my invention consists of an apparatus so
constructed as to offer a very extended surface or plane of a light yet
strong construction, which will have the same relation to the general
machine which the extended wings of a bird have to the body when a bird
is skimming in the air; but in place of the movement or power for onward
progress being obtained by movement of the extended surface or plane, as
is the case with the wings of birds, I apply suitable paddle-wheels
or other proper mechanical propellers worked by a steam or other
sufficiently light engine, and thus obtain the requisite power for
onward movement to the plane or extended surface; and in order to give
control as to the upward and downward direction of such a machine I
apply a tail to the extended surface which is capable of being inclined
or raised, so that when the power is acting to propel the machine, by
inclining the tail upwards, the resistance offered by the air will
cause the machine to rise on the air; and, on the contrary, when the
inclination of the tail is reversed, the machine will immediately be
propelled downwards, and pass through a plane more or less inclined to
the horizon as the inclination of the tail is greater or less; and in
order to guide the machine as to the lateral direction which it shall
take, I apply a vertical rudder or second tail, and, according as the
same is inclined in one direction or the other, so will be the direction
of the machine.'

The machine in question was very large, and differed very little from
the modern monoplane; the materials were to be spars of bamboo and
hollow wood, with diagonal wire bracing. The surface of the planes was
to amount to 4,500 square feet, and the tail, triangular in form (here
modern practice diverges) was to be 1,500 square feet. The inventor
estimated that there would be a sustaining power of half a pound per
square foot, and the driving power was to be supplied by a steam engine
of 25 to 30 horse-power, driving two six-bladed propellers. Henson was
largely dependent on Stringfellow for many details of his design, more
especially with regard to the construction of the engine.

The publication of the patent attracted a great amount of public
attention, and the illustrations in contemporary journals, representing
the machine flying over the pyramids and the Channel, anticipated fact
by sixty years and more; the scientific world was divided, as it was
up to the actual accomplishment of flight, as to the value of the
invention.

Strongfellow and Henson became associated after the conception of their
design, with an attorney named Colombine, and a Mr Marriott, and
between the four of them a project grew for putting the whole thing on
a commercial basis--Henson and Stringfellow were to supply the idea;
Marriott, knowing a member of Parliament, would be useful in getting a
company incorporated, and Colombine would look after the purely legal
side of the business. Thus an application was made by Mr Roebuck,
Marriott's M.P., for an act of incorporation for 'The Aerial Steam
Transit Company,' Roebuck moving to bring in the bill on the 24th of
March, 1843. The prospectus, calling for funds for the development of
the invention, makes interesting reading at this stage of aeronautical
development; it was as follows:

                     PROPOSAL.

For subscriptions of sums of L100, in furtherance of an Extraordinary
Invention not at present safe to be developed by securing the necessary
Patents, for which three times the sum advanced, namely, L300, is
conditionally guaranteed for each subscription on February 1, 1844,
in case of the anticipations being realised, with the option of the
subscribers being shareholders for the large amount if so desired, but
not otherwise.

---------An Invention has recently been discovered, which if ultimately
successful will be without parallel even in the age which introduced to
the world the wonderful effects of gas and of steam.

The discovery is of that peculiar nature, so simple in principle yet
so perfect in all the ingredients required for complete and permanent
success, that to promulgate it at present would wholly defeat its
development by the immense competition which would ensue, and the views
of the originator be entirely frustrated.

This work, the result of years of labour and study, presents a wonderful
instance of the adaptation of laws long since proved to the scientific
world combined with established principles so judiciously and carefully
arranged, as to produce a discovery perfect in all its parts and alike
in harmony with the laws of Nature and of science.

The Invention has been subjected to several tests and examinations
and the results are most satisfactory so much so that nothing but the
completion of the undertaking is required to determine its practical
operation, which being once established its utility is undoubted, as it
would be a necessary possession of every empire, and it were hardly too
much to say, of every individual of competent means in the civilised
world.

Its qualities and capabilities are so vast that it were impossible and,
even if possible, unsafe to develop them further, but some idea may
be formed from the fact that as a preliminary measure patents in Great
Britain Ireland, Scotland, the Colonies, France, Belgium, and the
United States, and every other country where protection to the first
discoveries of an Invention is granted, will of necessity be immediately
obtained, and by the time these are perfected, which it is estimated
will be in the month of February, the Invention will be fit for Public
Trial, but until the Patents are sealed any further disclosure would be
most dangerous to the principle on which it is based.

Under these circumstances, it is proposed to raise an immediate sum of
L2,000 in furtherance of the Projector's views, and as some protection
to the parties who may embark in the matter, that this is not a
visionary plan for objects imperfectly considered, Mr Colombine, to whom
the secret has been confided, has allowed his name to be used on the
occasion, and who will if referred to corroborate this statement, and
convince any inquirer of the reasonable prospects of large pecuniary
results following the development of the Invention.

It is, therefore, intended to raise the sum of L2,000 in twenty sums of
L100 each (of which any subscriber may take one or more not exceeding
five in number to be held by any individual) the amount of which is to
be paid into the hands of Mr Colombine as General Manager of the concern
to be by him appropriated in procuring the several Patents and providing
the expenses incidental to the works in progress. For each of which
sums of L100 it is intended and agreed that twelve months after the
1st February next, the several parties subscribing shall receive as an
equivalent for the risk to be run the sum of L300 for each of the sums
of L100 now subscribed, provided when the time arrives the Patents shall
be found to answer the purposes intended.

As full and complete success is alone looked to, no moderate or
imperfect benefit is to be anticipated, but the work, if it once passes
the necessary ordeal, to which inventions of every kind must be first
subject, will then be regarded by every one as the most astonishing
discovery of modern times; no half success can follow, and therefore the
full nature of the risk is immediately ascertained.

The intention is to work and prove the Patent by collective instead of
individual aid as less hazardous at first end more advantageous in the
result for the Inventor, as well as others, by having the interest of
several engaged in aiding one common object--the development of a
Great Plan. The failure is not feared, yet as perfect success might, by
possibility, not ensue, it is necessary to provide for that result,
and the parties concerned make it a condition that no return of
the subscribed money shall be required, if the Patents shall by any
unforeseen circumstances not be capable of being worked at all; against
which, the first application of the money subscribed, that of securing
the Patents, affords a reasonable security, as no one without solid
grounds would think of such an expenditure.

It is perfectly needless to state that no risk or responsibility of any
kind can arise beyond the payment of the sum to be subscribed under any
circumstances whatever.

As soon as the Patents shall be perfected and proved it is contemplated,
so far as may be found practicable, to further the great object in view
a Company shall be formed but respecting which it is unnecessary to
state further details, than that a preference will be given to all those
persons who now subscribe, and to whom shares shall be appropriated
according to the larger amount (being three times the sum to be paid by
each person) contemplated to be returned as soon as the success of the
Invention shall have been established, at their option, or the money
paid, whereby the Subscriber will have the means of either withdrawing
with a large pecuniary benefit, or by continuing his interest in the
concern lay the foundation for participating in the immense benefit
which must follow the success of the plan.

It is not pretended to conceal that the project is a speculation--all
parties believe that perfect success, and thence incalculable advantage
of every kind, will follow to every individual joining in this great
undertaking; but the Gentlemen engaged in it wish that no concealment
of the consequences, perfect success, or possible failure, should in the
slightest degree be inferred. They believe this will prove the germ of a
mighty work, and in that belief call for the operation of others with no
visionary object, but a legitimate one before them, to attain that point
where perfect success will be secured from their combined exertions.

All applications to be made to D. E. Colombine, Esquire, 8 Carlton
Chambers, Regent Street.

The applications did not materialise, as was only to be expected in view
of the vagueness of the proposals. Colombine did some advertising, and
Mr Roebuck expressed himself as unwilling to proceed further in the
venture. Henson experimented with models to a certain extent, while
Stringfellow looked for funds for the construction of a full-sized
monoplane. In November of 1843 he suggested that he and Henson should
construct a large model out of their own funds. On Henson's suggestion
Colombine and Marriott were bought out as regards the original patent,
and Stringfellow and Henson entered into an agreement and set to work.

Their work is briefly described in a little pamphlet by F. J.
Stringfellow, entitled A few Remarks on what has been done with
screw-propelled Aero-plane Machines from 1809 to 1892. The author writes
with regard to the work that his father and Henson undertook:--

'They commenced the construction of a small model operated by a spring,
and laid down the larger model 20 ft. from tip to tip of planes, 3 1/2
ft. wide, giving 70 ft. of sustaining surface, about 10 more in the
tail. The making of this model required great consideration; various
supports for the wings were tried, so as to combine lightness with
firmness, strength and rigidity.

'The planes were staid from three sets of fish-shaped masts, and rigged
square and firm by flat steel rigging. The engine and boiler were put in
the car to drive two screw-propellers, right and left-handed, 3 ft. in
diameter, with four blades each, occupying three-quarters of the area
of the circumference, set at an angle of 60 degrees. A considerable time
was spent in perfecting the motive power. Compressed air was tried and
abandoned. Tappets, cams, and eccentrics were all tried, to work the
slide valve, to obtain the best results. The piston rod of engine passed
through both ends of the cylinder, and with long connecting rods worked
direct on the crank of the propellers. From memorandum of experiments
still preserved the following is a copy of one: June, 27th, 1845, water
50 ozs., spirit 10 ozs., lamp lit 8.45, gauge moves 8.46, engine started
8.48 (100 lb. pressure), engine stopped 8.57, worked 9 minutes, 2,288
revolutions, average 254 per minute. No priming, 40 ozs. water consumed,
propulsion (thrust of propellers), 5 lbs. 4 1/2 ozs. at commencement,
steady, 4 lbs. 1/2 oz., 57 revolutions to 1 oz. water, steam cut off
one-third from beginning.

'The diameter of cylinder of engine was 1 1/2 inch, length of stroke 3
inches.

'In the meantime an engine was also made for the smaller model, and a
wing action tried, but with poor results. The time was mostly devoted to
the larger model, and in 1847 a tent was erected on Bala Down, about two
miles from Chard, and the model taken up one night by the workmen. The
experiments were not so favourable as was expected. The machine could
not support itself for any distance, but, when launched off, gradually
descended, although the power and surface should have been ample;
indeed, according to latest calculations, the thrust should have carried
more than three times the weight, for there was a thrust of 5 lbs. from
the propellers, and a surface of over 70 square feet to sustain under 30
lbs., but necessary speed was lacking.'

Stringfellow himself explained the failure as follows:--

'There stood our aerial protegee in all her purity--too delicate, too
fragile, too beautiful for this rough world; at least those were
my ideas at the time, but little did I think how soon it was to be
realised. I soon found, before I had time to introduce the spark, a
drooping in the wings, a flagging in all the parts. In less than ten
minutes the machine was saturated with wet from a deposit of dew, so
that anything like a trial was impossible by night. I did not consider
we could get the silk tight and rigid enough. Indeed, the framework
altogether was too weak. The steam-engine was the best part. Our want of
success was not for want of power or sustaining surface, but for want of
proper adaptation of the means to the end of the various parts.'

Henson, who had spent a considerable amount of money in these
experimental constructions, consoled himself for failure by venturing
into matrimony; in 1849 he went to America, leaving Stringfellow to
continue experimenting alone. From 1846 to 1848 Stringfellow worked on
what is really an epoch-making item in the history of aeronautics--the
first engine-driven aeroplane which actually flew. The machine in
question had a 10 foot span, and was 2 ft. across in the widest part of
the wing; the length of tail was 3 ft. 6 ins., and the span of tail in
the widest part 22 ins., the total sustaining area being about 14
sq. ft. The motive power consisted of an engine with a cylinder of
three-quarter inch diameter and a two-inch stroke; between this and
the crank shaft was a bevelled gear giving three revolutions of the
propellers to every stroke of the engine; the propellers, right and left
screw, were four-bladed and 16 inches in diameter. The total weight of
the model with engine was 8 lbs. Its successful flight is ascribed to
the fact that Stringfellow curved the wings, giving them rigid front
edges and flexible trailing edges, as suggested long before both by Da
Vinci and Borelli, but never before put into practice.

Mr F. J. Stringfellow, in the pamphlet quoted above, gives the best
account of the flight of this model: 'My father had constructed another
small model which was finished early in 1848, and having the loan of a
long room in a disused lace factory, early in June the small model was
moved there for experiments. The room was about 22 yards long and
from 10 to 12 ft. high.... The inclined wire for starting the machine
occupied less than half the length of the room and left space at the end
for the machine to clear the floor. In the first experiment the tail was
set at too high an angle, and the machine rose too rapidly on leaving
the wire. After going a few yards it slid back as if coming down an
inclined plane, at such an angle that the point of the tail struck the
ground and was broken. The tail was repaired and set at a smaller angle.
The steam was again got up, and the machine started down the wire, and,
upon reaching the point of self-detachment, it gradually rose until
it reached the farther end of the room, striking a hole in the canvas
placed to stop it. In experiments the machine flew well, when rising as
much as one in seven. The late Rev. J. Riste, Esq., lace manufacturer,
Northcote Spicer, Esq., J. Toms, Esq., and others witnessed experiments.
Mr Marriatt, late of the San Francisco News Letter brought down from
London Mr Ellis, the then lessee of Cremorne Gardens, Mr Partridge, and
Lieutenant Gale, the aeronaut, to witness experiments. Mr Ellis offered
to construct a covered way at Cremorne for experiments. Mr Stringfellow
repaired to Cremorne, but not much better accommodations than he had
at home were provided, owing to unfulfilled engagement as to room.
Mr Stringfellow was preparing for departure when a party of gentlemen
unconnected with the Gardens begged to see an experiment, and finding
them able to appreciate his endeavours, he got up steam and started the
model down the wire. When it arrived at the spot where it should leave
the wire it appeared to meet with some obstruction, and threatened to
come to the ground, but it soon recovered itself and darted off in
as fair a flight as it was possible to make at a distance of about 40
yards, where it was stopped by the canvas.

'Having now demonstrated the practicability of making a steam-engine
fly, and finding nothing but a pecuniary loss and little honour,
this experimenter rested for a long time, satisfied with what he had
effected. The subject, however, had to him special charms, and he still
contemplated the renewal of his experiments.'

It appears that Stringfellow's interest did not revive sufficiently
for the continuance of the experiments until the founding of the
Aeronautical Society of Great Britain in 1866. Wenham's paper on Aerial
Locomotion read at the first meeting of the Society, which was held at
the Society of Arts under the Presidency of the Duke of Argyll, was
the means of bringing Stringfellow back into the field. It was Wenham's
suggestion, in the first place, that monoplane design should be
abandoned for the superposition of planes; acting on this suggestion
Stringfellow constructed a model triplane, and also designed a steam
engine of slightly over one horse-power, and a one horse-power copper
boiler and fire box which, although capable of sustaining a pressure of
500 lbs. to the square inch, weighed only about 40 lbs.

Both the engine and the triplane model were exhibited at the first
Aeronautical Exhibition held at the Crystal Palace in 1868. The triplane
had a supporting surface of 28 sq. ft.; inclusive of engine, boiler,
fuel, and water its total weight was under 12 lbs. The engine worked two
21 in. propellers at 600 revolutions per minute, and developed 100 lbs.
steam pressure in five minutes, yielding one-third horse-power. Since
no free flight was allowed in the Exhibition, owing to danger from fire,
the triplane was suspended from a wire in the nave of the building,
and it was noted that, when running along the wire, the model made a
perceptible lift.

A prize of L100 was awarded to the steam engine as the lightest steam
engine in proportion to its power. The engine and model together may
be reckoned as Stringfellow's best achievement. He used his L100 in
preparation for further experiments, but he was now an old man, and
his work was practically done. Both the triplane and the engine were
eventually bought for the Washington Museum; Stringfellow's earlier
models, together with those constructed by him in conjunction with
Henson, remain in this country in the Victoria and Albert Museum.

John Stringfellow died on December 13th, 1883. His place in the history
of aeronautics is at least equal to that of Cayley, and it may be
said that he laid the foundation of such work as was subsequently
accomplished by Maxim, Langley, and their fellows. It was the coming of
the internal combustion engine that rendered flight practicable, and had
this prime mover been available in John Stringfellow's day the Wright
brothers' achievement might have been antedated by half a century.




V. WENHAM, LE BRIS, AND SOME OTHERS

There are few outstanding events in the development of aeronautics
between Stringfellow's final achievement and the work of such men as
Lilienthal, Pilcher, Montgomery, and their kind; in spite of this, the
later middle decades of the nineteenth century witnessed a considerable
amount of spade work both in England and in France, the two countries
which led in the way in aeronautical development until Lilienthal gave
honour to Germany, and Langley and Montgomery paved the way for the
Wright Brothers in America.

Two abortive attempts characterised the sixties of last century in
France. As regards the first of these, it was carried out by three men,
Nadar, Ponton d'Amecourt, and De la Landelle, who conceived the idea
of a full-sized helicopter machine. D'Amecourt exhibited a steam model,
constructed in 1865, at the Aeronautical Society's Exhibition in 1868.
The engine was aluminium with cylinders of bronze, driving two screws
placed one above the other and rotating in Opposite directions, but the
power was not sufficient to lift the model. De la Landelle's principal
achievement consisted in the publication in 1863 of a book entitled
Aviation which has a certain historical value; he got out several
designs for large machines on the helicopter principle, but did little
more until the three combined in the attempt to raise funds for the
construction of their full-sized machine. Since the funds were not
forthcoming, Nadar took to ballooning as the means of raising money;
apparently he found this substitute for real flight sufficiently
interesting to divert him from the study of the helicopter principle,
for the experiment went no further.

The other experimenter of this period, one Count d'Esterno, took out a
patent in 1864 for a soaring machine which allowed for alteration of
the angle of incidence of the wings in the manner that was subsequently
carried out by the Wright Brothers. It was not until 1883 that any
attempt was made to put this patent to practical use, and, as the
inventor died while it was under construction, it was never completed.
D'Esterno was also responsible for the production of a work entitled
Du Vol des Oiseaux, which is a very remarkable study of the flight of
birds.

Mention has already been made of the founding of the Aeronautical
Society of Great Britain, which, since 1918 has been the Royal
Aeronautical Society. 1866 witnessed the first meeting of the Society
under the Presidency of the Duke of Argyll, when in June, at the Society
of Arts, Francis Herbert Wenham read his now classic paper Aerial
Locomotion. Certain quotations from this will show how clearly Wenham
had thought out the problems connected with flight.

'The first subject for consideration is the proportion of surface to
weight, and their combined effect in descending perpendicularly through
the atmosphere. The datum is here based upon the consideration of
safety, for it may sometimes be needful for a living being to drop
passively, without muscular effort. One square foot of sustaining
surface for every pound of the total weight will be sufficient for
security.

'According to Smeaton's table of atmospheric resistances, to produce
a force of one pound on a square foot, the wind must move against the
plane (or which is the same thing, the plane against the wind), at the
rate of twenty-two feet per second, or 1,320 feet per minute, equal to
fifteen miles per hour. The resistance of the air will now balance the
weight on the descending surface, and, consequently, it cannot exceed
that speed. Now, twenty-two feet per second is the velocity acquired at
the end of a fall of eight feet--a height from which a well-knit man or
animal may leap down without much risk of injury. Therefore, if a man
with parachute weigh together 143 lbs., spreading the same number of
square feet of surface contained in a circle fourteen and a half feet
in diameter, he will descend at perhaps an unpleasant velocity, but with
safety to life and limb.

'It is a remarkable fact how this proportion of wing-surface to weight
extends throughout a great variety of the flying portion of the
animal kingdom, even down to hornets, bees, and other insects. In some
instances, however, as in the gallinaceous tribe, including pheasants,
this area is somewhat exceeded, but they are known to be very poor
fliers. Residing as they do chiefly on the ground, their wings are
only required for short distances, or for raising them or easing their
descent from their roosting-places in forest trees, the shortness
of their wings preventing them from taking extended flights. The
wing-surface of the common swallow is rather more than in the ratio of
two square feet per pound, but having also great length of pinion, it is
both swift and enduring in its flight. When on a rapid course this bird
is in the habit of furling its wings into a narrow compass. The greater
extent of surface is probably needful for the continual variations of
speed and instant stoppages for obtaining its insect food.

'On the other hand, there are some birds, particularly of the duck
tribe, whose wing-surface but little exceeds half a square foot,
or seventy-two inches per pound, yet they may be classed among the
strongest and swiftest of fliers. A weight of one pound, suspended
from an area of this extent, would acquire a velocity due to a fall of
sixteen feet--a height sufficient for the destruction or injury of most
animals. But when the plane is urged forward horizontally, in a manner
analogous to the wings of a bird during flight, the sustaining power is
greatly influenced by the form and arrangement of the surface.

'In the case of perpendicular descent, as a parachute, the sustaining
effect will be much the same, whatever the figure of the outline of the
superficies may be, and a circle perhaps affords the best resistance of
any. Take, for example, a circle of twenty square feet (as possessed
by the pelican) loaded with as many pounds. This, as just stated, will
limit the rate of perpendicular descent to 1,320 feet per minute. But
instead of a circle sixty-one inches in diameter, if the area is bounded
by a parallelogram ten feet long by two feet broad, and whilst at
perfect freedom to descend perpendicularly, let a force be applied
exactly in a horizontal direction, so as to carry it edgeways, with the
long side foremost, at a forward speed of thirty miles per hour--just
double that of its passive descent: the rate of fall under these
conditions will be decreased most remarkably, probably to less than
one-fifteenth part, or eighty-eight feet per minute, or one mile per
hour.'

And again: 'It has before been shown how utterly inadequate the mere
perpendicular impulse of a plane is found to be in supporting a weight,
when there is no horizontal motion at the time. There is no material
weight of air to be acted upon, and it yields to the slightest force,
however great the velocity of impulse may be. On the other hand, suppose
that a large bird, in full flight, can make forty miles per hour, or
3,520 feet per minute, and performs one stroke per second. Now, during
every fractional portion of that stroke, the wing is acting upon and
obtaining an impulse from a fresh and undisturbed body of air; and if
the vibration of the wing is limited to an arc of two feet, this by no
means represents the small force of action that would be obtained when
in a stationary position, for the impulse is secured upon a stratum of
fifty-eight feet in length of air at each stroke. So that the conditions
of weight of air for obtaining support equally well apply to weight of
air and its reaction in producing forward impulse.

'So necessary is the acquirement of this horizontal speed, even in
commencing flight, that most heavy birds, when possible, rise against
the wind, and even run at the top of their speed to make their wings
available, as in the example of the eagle, mentioned at the commencement
of this paper. It is stated that the Arabs, on horseback, can approach
near enough to spear these birds, when on the plain, before they are
able to rise; their habit is to perch on an eminence, where possible.

'The tail of a bird is not necessary for flight. A pigeon can fly
perfectly with this appendage cut short off; it probably performs an
important function in steering, for it is to be remarked, that most
birds that have either to pursue or evade pursuit are amply provided
with this organ.

'The foregoing reasoning is based upon facts, which tend to show that
the flight of the largest and heaviest of all birds is really performed
with but a small amount of force, and that man is endowed with
sufficient muscular power to enable him also to take individual and
extended flights, and that success is probably only involved in a
question of suitable mechanical adaptations. But if the wings are to be
modelled in imitation of natural examples, but very little consideration
will serve to demonstrate its utter impracticability when applied in
these forms.'

Thus Wenham, one of the best theorists of his age. The Society with
which this paper connects his name has done work, between that time and
the present, of which the importance cannot be overestimated, and has
been of the greatest value in the development of aeronautics, both in
theory and experiment. The objects of the Society are to give a stronger
impulse to the scientific study of aerial navigation, to promote the
intercourse of those interested in the subject at home and abroad, and
to give advice and instruction to those who study the principles upon
which aeronautical science is based. From the date of its foundation the
Society has given special study to dynamic flight, putting this before
ballooning. Its library, its bureau of advice and information, and its
meetings, all assist in forwarding the study of aeronautics, and its
twenty-three early Annual Reports are of considerable value, containing
as they do a large amount of useful information on aeronautical
subjects, and forming practically the basis of aeronautical science.

Ante to Wenham, Stringfellow and the French experimenters already noted,
by some years, was Le Bris, a French sea captain, who appears to have
required only a thorough scientific training to have rendered him of
equal moment in the history of gliding flight with Lilienthal himself.
Le Bris, it appears, watched the albatross and deduced, from the manner
in which it supported itself in the air, that plane surfaces could
be constructed and arranged to support a man in like manner. Octave
Chanute, himself a leading exponent of gliding, gives the best
description of Le Bris's experiments in a work, Progress in Flying
Machines, which, although published as recently as I 1894, is already
rare. Chanute draws from a still rarer book, namely, De la Landelle's
work published in 1884. Le Bris himself, quoted by De la Landelle as
speaking of his first visioning of human flight, describes how he killed
an albatross, and then--'I took the wing of the albatross and exposed
it to the breeze; and lo! in spite of me it drew forward into the wind;
notwithstanding my resistance it tended to rise. Thus I had discovered
the secret of the bird! I comprehended the whole mystery of flight.'

This apparently took place while at sea; later on Le Bris, returning to
France, designed and constructed an artificial albatross of sufficient
size to bear his own weight. The fact that he followed the bird outline
as closely as he did attests his lack of scientific training for his
task, while at the same time the success of the experiment was proof of
his genius. The body of his artificial bird, boat-shaped, was 13 1/2 ft.
in length, with a breadth of 4 ft. at the widest part. The material
was cloth stretched over a wooden framework; in front was a small mast
rigged after the manner of a ship's masts to which were attached poles
and cords with which Le Bris intended to work the wings. Each wing was
23 ft. in length, giving a total supporting surface of nearly 220 sq.
ft.; the weight of the whole apparatus was only 92 pounds. For steering,
both vertical and horizontal, a hinged tail was provided, and the
leading edge of each wing was made flexible. In construction throughout,
and especially in that of the wings, Le Bris adhered as closely as
possible to the original albatross.

He designed an ingenious kind of mechanism which he termed 'Rotules,'
which by means of two levers gave a rotary motion to the front edge of
the wings, and also permitted of their adjustment to various angles.
The inventor's idea was to stand upright in the body of the contrivance,
working the levers and cords with his hands, and with his feet on
a pedal by means of which the steering tail was to be worked. He
anticipated that, given a strong wind, he could rise into the air after
the manner of an albatross, without any need for flapping his wings, and
the account of his first experiment forms one of the most interesting
incidents in the history of flight. It is related in full in Chanute's
work, from which the present account is summarised.

Le Bris made his first experiment on a main road near Douarnenez, at
Trefeuntec. From his observation of the albatross Le Bris concluded
that it was necessary to get some initial velocity in order to make the
machine rise; consequently on a Sunday morning, with a breeze of about
12 miles an hour blowing down the road, he had his albatross placed on a
cart and set off, with a peasant driver, against the wind. At the outset
the machine was fastened to the cart by a rope running through the rails
on which the machine rested, and secured by a slip knot on Le Bris's own
wrist, so that only a jerk on his part was necessary to loosen the rope
and set the machine free. On each side walked an assistant holding the
wings, and when a turn of the road brought the machine full into the
wind these men were instructed to let go, while the driver increased the
pace from a walk to a trot. Le Bris, by pressure on the levers of the
machine, raised the front edges of his wings slightly; they took the
wind almost instantly to such an extent that the horse, relieved of a
great part of the weight he had been drawing, turned his trot into a
gallop. Le Bris gave the jerk of the rope that should have unfastened
the slip knot, but a concealed nail on the cart caught the rope, so that
it failed to run. The lift of the machine was such, however, that it
relieved the horse of very nearly the weight of the cart and driver, as
well as that of Le Bris and his machine, and in the end the rails of the
cart gave way. Le Bris rose in the air, the machine maintaining perfect
balance and rising to a height of nearly 300 ft., the total length of
the glide being upwards of an eighth of a mile. But at the last moment
the rope which had originally fastened the machine to the cart got wound
round the driver's body, so that this unfortunate dangled in the air
under Le Bris and probably assisted in maintaining the balance of the
artificial albatross. Le Bris, congratulating himself on his success,
was prepared to enjoy just as long a time in the air as the pressure of
the wind would permit, but the howls of the unfortunate driver at the
end of the rope beneath him dispelled his dreams; by working his levers
he altered the angle of the front wing edges so skilfully as to make a
very successful landing indeed for the driver, who, entirely uninjured,
disentangled himself from the rope as soon as he touched the ground, and
ran off to retrieve his horse and cart.

Apparently his release made a difference in the centre of gravity, for
Le Bris could not manipulate his levers for further ascent; by skilful
manipulation he retarded the descent sufficiently to escape injury to
himself; the machine descended at an angle, so that one wing, striking
the ground in front of the other, received a certain amount of damage.

It may have been on account of the reluctance of this same or another
driver that Le Bris chose a different method of launching himself in
making a second experiment with his albatross. He chose the edge of a
quarry which had been excavated in a depression of the ground; here he
assembled his apparatus at the bottom of the quarry, and by means of a
rope was hoisted to a height of nearly 100 ft. from the quarry bottom,
this rope being attached to a mast which he had erected upon the edge
of the depression in which the quarry was situated. Thus hoisted, the
albatross was swung to face a strong breeze that blew inland, and Le
Bris manipulated his levers to give the front edges of his wings a
downward angle, so that only the top surfaces should take the wing
pressure. Having got his balance, he obtained a lifting angle of
incidence on the wings by means of his levers, and released the hook
that secured the machine, gliding off over the quarry. On the glide he
met with the inevitable upward current of air that the quarry and the
depression in which it was situated caused; this current upset the
balance of the machine and flung it to the bottom of the quarry,
breaking it to fragments. Le Bris, apparently as intrepid as ingenious,
gripped the mast from which his levers were worked, and, springing
upward as the machine touched earth, escaped with no more damage than a
broken leg. But for the rebound of the levers he would have escaped even
this.

The interest of these experiments is enhanced by the fact that Le Bris
was a seafaring man who conducted them from love of the science which
had fired his imagination, and in so doing exhausted his own small
means. It was in 1855 that he made these initial attempts, and
twelve years passed before his persistence was rewarded by a public
subscription made at Brest for the purpose of enabling him to continue
his experiments. He built a second albatross, and on the advice of his
friends ballasted it for flight instead of travelling in it himself. It
was not so successful as the first, probably owing to the lack of human
control while in flight; on one of the trials a height of 150 ft. was
attained, the glider being secured by a thin rope and held so as to face
into the wind. A glide of nearly an eighth of a mile was made with the
rope hanging slack, and, at the end of this distance, a rise in the
ground modified the force of the wind, whereupon the machine settled
down without damage. A further trial in a gusty wind resulted in the
complete destruction of this second machine; Le Bris had no more
funds, no further subscriptions were likely to materialise, and so
the experiments of this first exponent of the art of gliding (save
for Besnier and his kind) came to an end. They constituted a notable
achievement, and undoubtedly Le Bris deserves a better place than has
been accorded him in the ranks of the early experimenters.

Contemporary with him was Charles Spencer, the first man to practice
gliding in England. His apparatus consisted of a pair of wings with a
total area of 30 sq. ft., to which a tail and body were attached. The
weight of this apparatus was some 24 lbs., and, launching himself on
it from a small eminence, as was done later by Lilienthal in his
experiments, the inventor made flights of over 120 feet. The glider in
question was exhibited at the Aeronautical Exhibition of 1868.




VI. THE AGE OF THE GIANTS

Until the Wright Brothers definitely solved the problem of flight and
virtually gave the aeroplane its present place in aeronautics, there
were three definite schools of experiment. The first of these was
that which sought to imitate nature by means of the ornithopter or
flapping-wing machines directly imitative of bird flight; the second
school was that which believed in the helicopter or lifting screw; the
third and eventually successful school is that which followed up the
principle enunciated by Cayley, that of opposing a plane surface to the
resistance of the air by supplying suitable motive power to drive it at
the requisite angle for support.

Engineering problems generally go to prove that too close an imitation
of nature in her forms of recipro-cating motion is not advantageous; it
is impossible to copy the minutiae of a bird's wing effectively, and the
bird in flight depends on the tiniest details of its feathers just as
much as on the general principle on which the whole wing is constructed.
Bird flight, however, has attracted many experimenters, including even
Lilienthal; among others may be mentioned F. W. Brearey, who invented
what he called the 'Pectoral cord,' which stored energy on each upstroke
of the artificial wing; E. P. Frost; Major R. Moore, and especially
Hureau de Villeneuve, a most enthusiastic student of this form of
flight, who began his experiments about 1865, and altogether designed
and made nearly 300 artificial birds, one of his later constructions
was a machine in bird form with a wing span of about 50 ft.; the
motive power for this was supplied by steam from a boiler which, being
stationary on the ground, was connected by a length of hose to the
machine. De Villeneuve, turning on steam for his first trial, obtained
sufficient power to make the wings beat very forcibly; with the inventor
on the machine the latter rose several feet into the air, whereupon de
Villeneuve grew nervous and turned off the steam supply. The machine
fell to the earth, breaking one of its wings, and it does not appear
that de Villeneuve troubled to reconstruct it. This experiment remains
as the greatest success yet achieved by any machine constructed on the
ornithopter principle.

It may be that, as forecasted by the prophet Wells, the flapping-wing
machine will yet come to its own and compete with the aeroplane in
efficiency. Against this, however, are the practical advantages of
the rotary mechanism of the aeroplane propeller as compared with the
movement of a bird's wing, which, according to Marey, moves in a figure
of eight. The force derived from a propeller is of necessity continual,
while it is equally obvious that that derived from a flapping movement
is intermittent, and, in the recovery of a wing after completion of one
stroke for the next, there is necessarily a certain cessation, if not
loss, of power.

The matter of experiment along any lines in connection with aviation is
primarily one of hard cash. Throughout the whole history of flight up to
the outbreak of the European war development has been handicapped on
the score of finance, and, since the arrival of the aeroplane, both
ornithopter and helicopter schools have been handicapped by this
consideration. Thus serious study of the efficiency of wings in
imitation of those of the living bird has not been carried to a point
that might win success for this method of propulsion. Even Wilbur Wright
studied this subject and propounded certain theories, while a later and
possibly more scientific student, F. W. Lanchester, has also contributed
empirical conclusions. Another and earlier student was Lawrence
Hargrave, who made a wing-propelled model which achieved successful
flight, and in 1885 was exhibited before the Royal Society of New South
Wales. Hargrave called the principle on which his propeller worked that
of a 'Trochoided plane'; it was, in effect, similar to the feathering of
an oar.

Hargrave, to diverge for a brief while from the machine to the man,
was one who, although he achieved nothing worthy of special remark,
contributed a great deal of painstaking work to the science of flight.
He made a series of experiments with man-lifting kites in addition to
making a study of flapping-wing flight. It cannot be said that he set
forth any new principle; his work was mainly imitative, but at the same
time by developing ideas originated in great measure by others he helped
toward the solution of the problem.

Attempts at flight on the helicopter principle consist in the work of De
la Landelle and others already mentioned. The possibility of flight by
this method is modified by a very definite disadvantage of which lovers
of the helicopter seem to take little account. It is always claimed for
a machine of this type that it possesses great advantages both in rising
and in landing, since, if it were effective, it would obviously be able
to rise from and alight on any ground capable of containing its own
bulk; a further advantage claimed is that the helicopter would be able
to remain stationary in the air, maintaining itself in any position by
the vertical lift of its propeller.

These potential assets do not take into consideration the fact that
efficiency is required not only in rising, landing, and remaining
stationary in the air, but also in actual flight. It must be evident
that if a certain amount of the motive force is used in maintaining the
machine off the ground, that amount of force is missing from the total
of horizontal driving power. Again, it is often assumed by advocates of
this form of flight that the rapidity of climb of the helicopter would
be far greater than that of the driven plane; this view overlooks the
fact that the maintenance of aerodynamic support would claim the greater
part of the engine-power; the rate of ascent would be governed by the
amount of power that could be developed surplus to that required for
maintenance.

This is best explained by actual figures: assuming that a propeller 15
ft. in diameter is used, almost 50 horse-power would be required to
get an upward lift of 1,000 pounds; this amount of horse-power would be
continually absorbed in maintaining the machine in the air at any given
level; for actual lift from one level to another at a speed of eleven
feet per second a further 20 horse-power would be required, which means
that 70 horse-power must be constantly provided for; this absorption
of power in the mere maintenance of aero-dynamic support is a permanent
drawback.

The attraction of the helicopter lies, probably, in the ease with which
flight is demonstrated by means of models constructed on this principle,
but one truism with regard to the principles of flight is that the
problems change remarkably, and often unexpectedly, with the size of
the machine constructed for experiment. Berriman, in a brief but very
interesting manual entitled Principles of Flight, assumed that 'there is
a significant dimension of which the effective area is an expression
of the second power, while the weight became an expression of the third
power. Then once again we have the two-thirds power law militating
against the successful construction of large helicopters, on the ground
that the essential weight increases disproportionately fast to the
effective area. From a consideration of the structural features of
propellers it is evident that this particular relationship does not
apply in practice, but it seems reasonable that some such governing
factor should exist as an explanation of the apparent failure of all
full-sized machines that have been constructed. Among models there is
nothing more strikingly successful than the toy helicopter, in which the
essential weight is so small compared with the effective area.'

De la Landelle's work, already mentioned, was carried on a few years
later by another Frenchman, Castel, who constructed a machine with eight
propellers arranged in two fours and driven by a compressed air motor or
engine. The model with which Castel experimented had a total weight of
only 49 lbs.; it rose in the air and smashed itself by driving against
a wall, and the inventor does not seem to have proceeded further.
Contemporary with Castel was Professor Forlanini, whose design was for
a machine very similar to de la Landelle's, with two superposed screws.
This machine ranks as the second on the helicopter principle to achieve
flight; it remained in the air for no less than the third of a minute in
one of its trials.

Later experimenters in this direction were Kress, a German; Professor
Wellner, an Austrian; and W. R. Kimball, an American. Kress, like most
Germans, set to the development of an idea which others had originated;
he followed de la Landelle and Forlanini by fitting two superposed
propellers revolving in opposite directions, and with this machine he
achieved good results as regards horse-power to weight; Kimball, it
appears, did not get beyond the rubber-driven model stage, and any
success he may have achieved was modified by the theory enunciated by
Berriman and quoted above.

Comparing these two schools of thought, the helicopter and bird-flight
schools, it appears that the latter has the greater chance of eventual
success--that is, if either should ever come into competition with the
aeroplane as effective means of flight. So far, the aeroplane holds
the field, but the whole science of flight is so new and so full of
unexpected developments that this is no reason for assuming that other
means may not give equal effect, when money and brains are diverted from
the driven plane to a closer imitation of natural flight.

Reverting from non-success to success, from consideration of the two
methods mentioned above to the direction in which practical flight
has been achieved, it is to be noted that between the time of Le
Bris, Stringfellow, and their contemporaries, and the nineties of last
century, there was much plodding work carried out with little visible
result, more especially so far as English students were concerned. Among
the incidents of those years is one of the most pathetic tragedies in
the whole history of aviation, that of Alphonse Penaud, who, in his
thirty years of life, condensed the experience of his predecessors and
combined it with his own genius to state in a published patent what
the aeroplane of to-day should be. Consider the following abstract of
Penaud's design as published in his patent of 1876, and comparison of
this with the aeroplane that now exists will show very few divergences
except for those forced on the inventor by the fact that the internal
combustion engine had not then developed. The double surfaced planes
were to be built with wooden ribs and arranged with a slight dihedral
angle; there was to be a large aspect ratio and the wings were cambered
as in Stringfellow's later models. Provision was made for warping the
wings while in flight, and the trailing edges were so designed as to
be capable of upward twist while the machine was in the air. The planes
were to be placed above the car, and provision was even made for a glass
wind-screen to give protection to the pilot during flight. Steering was
to be accomplished by means of lateral and vertical planes forming
a tail; these controlled by a single lever corresponding to the 'joy
stick' of the present day plane.

Penaud conceived this machine as driven by two propellers; alternatively
these could be driven by petrol or steam-fed motor, and the centre of
gravity of the machine while in flight was in the front fifth of the
wings. Penaud estimated from 20 to 30 horse-power sufficient to drive
this machine, weighing with pilot and passenger 2,600 lbs., through the
air at a speed of 60 miles an hour, with the wings set at an angle
of incidence of two degrees. So complete was the design that it even
included instruments, consisting of an aneroid, pressure indicator, an
anemometer, a compass, and a level. There, with few alterations, is the
aeroplane as we know it--and Penaud was twenty-seven when his patent was
published.

For three years longer he worked, experimenting with models,
contributing essays and other valuable data to French papers on the
subject of aeronautics. His gains were ill health, poverty, and neglect,
and at the age of thirty a pistol shot put an end to what had promised
to be one of the most brilliant careers in all the history of flight.

Two years before the publication of Penaud's patent Thomas Moy
experimented at the Crystal Palace with a twin-propelled aeroplane,
steam driven, which seems to have failed mainly because the internal
combustion engine had not yet come to give sufficient power for weight.
Moy anchored his machine to a pole running on a prepared circular track;
his engine weighed 80 lbs. and, developing only three horse-power, gave
him a speed of 12 miles an hour. He himself estimated that the machine
would not rise until he could get a speed of 35 miles an hour, and his
estimate was correct. Two six-bladed propellers were placed side by side
between the two main planes of the machine, which was supported on a
triangular wheeled undercarriage and steered by fairly conventional tail
planes. Moy realised that he could not get sufficient power to achieve
flight, but he went on experimenting in various directions, and left
much data concerning his experiments which has not yet been deemed
worthy of publication, but which still contains a mass of information
that is of practical utility, embodying as it does a vast amount of
painstaking work.

Penaud and Moy were followed by Goupil, a Frenchman, who, in place of
attempting to fit a motor to an aeroplane, experimented by making the
wind his motor. He anchored his machine to the ground, allowing it two
feet of lift, and merely waited for a wind to come along and lift it.
The machine was stream lined, and the wings, curving as in the early
German patterns of war aeroplanes, gave a total lifting surface of about
290 sq. ft. Anchored to the ground and facing a wind of 19 feet per
second, Goupil's machine lifted its own weight and that of two men as
well to the limit of its anchorage. Although this took place as late
as 1883 the inventor went no further in practical work. He published a
book, however, entitled La Locomotion Aerienne, which is still of great
importance, more especially on the subject of inherent stability.

In 1884 came the first patents of Horatio Phillips, whose work lay
mainly in the direction of investigation into the curvature of plane
surfaces, with a view to obtaining the greatest amount of support.
Phillips was one of the first to treat the problem of curvature of
planes as a matter for scientific experiment, and, great as has been the
development of the driven plane in the 36 years that have passed since
he began, there is still room for investigation into the subject which
he studied so persistently and with such valuable result.

At this point it may be noted that, with the solitary exception of
Le Bris, practically every student of flight had so far set about
constructing the means of launching humanity into the air without any
attempt at ascertaining the nature and peculiarities of the sustaining
medium. The attitude of experimenters in general might be compared to
that of a man who from boyhood had grown up away from open water, and,
at the first sight of an expanse of water, set to work to construct a
boat with a vague idea that, since wood would float, only sufficient
power was required to make him an efficient navigator. Accident,
perhaps, in the shape of lack of means of procuring driving power, drove
Le Bris to the form of experiment which he actually carried out; it
remained for the later years of the nineteenth century to produce men
who were content to ascertain the nature of the support the air would
afford before attempting to drive themselves through it.

Of the age in which these men lived and worked, giving their all in many
cases to the science they loved, even to life itself, it may be said
with truth that 'there were giants on the earth in those days,' as far
as aeronautics is in question. It was an age of giants who lived and
dared and died, venturing into uncharted space, knowing nothing of its
dangers, giving, as a man gives to his mistress, without stint and
for the joy of the giving. The science of to-day, compared with the
glimmerings that were in that age of the giants, is a fixed and certain
thing; the problems of to-day are minor problems, for the great major
problem vanished in solution when the Wright Brothers made their first
ascent. In that age of the giants was evolved the flying man, the new
type in human species which found full expression and came to full
development in the days of the war, achieving feats of daring and
endurance which leave the commonplace landsman staggered at thought of
that of which his fellows prove themselves capable. He is a new type,
this flying man, a being of self-forgetfulness; of such was Lilienthal,
of such was Pilcher; of such in later days were Farman, Bleriot, Hamel,
Rolls, and their fellows; great names that will live for as long as man
flies, adventurers equally with those of the spacious days of Elizabeth.
To each of these came the call, and he worked and dared and passed,
having, perhaps, advanced one little step in the long march that has led
toward the perfecting of flight.

It is not yet twenty years since man first flew, but into that twenty
years have been compressed a century or so of progress, while, in the
two decades that preceded it, was compressed still more. We have only to
recall and recount the work of four men: Lilienthal, Langley, Pilcher,
and Clement Ader to see the immense stride that was made between the
time when Penaud pulled a trigger for the last time and the Wright
Brothers first left the earth. Into those two decades was compressed the
investigation that meant knowledge of the qualities of the air, together
with the development of the one prime mover that rendered flight a
possibility--the internal combustion engine. The coming and progress of
this latter is a thing apart, to be detailed separately; for the present
we are concerned with the evolution of the driven plane, and with it the
evolution of that daring being, the flying man. The two are inseparable,
for the men gave themselves to their art; the story of Lilienthal's life
and death is the story of his work; the story of Pilcher's work is that
of his life and death.

Considering the flying man as he appeared in the war period, there
entered into his composition a new element--patriotism--which brought
about a modification of the type, or, perhaps, made it appear that
certain men belonged to the type who in reality were commonplace
mortals, animated, under normal conditions, by normal motives, but
driven by the stress of the time to take rank with the last expression
of human energy, the flying type. However that may be, what may be
termed the mathematising of aeronautics has rendered the type itself
evanescent; your pilot of to-day knows his craft, once he is trained,
much in the manner that a driver of a motor-lorry knows his vehicle;
design has been systematised, capabilities have been tabulated; camber,
dihedral angle, aspect ratio, engine power, and plane surface, are
business items of drawing office and machine shop; there is room for
enterprise, for genius, and for skill; once and again there is room for
daring, as in the first Atlantic flight. Yet that again was a thing of
mathematical calculation and petrol storage, allied to a certain stark
courage which may be found even in landsmen. For the ventures into the
unknown, the limit of daring, the work for work's sake, with the almost
certainty that the final reward was death, we must look back to the age
of the giants, the age when flying was not a business, but romance.




VII. LILIENTHAL AND PILCHER

There was never a more enthusiastic and consistent student of the
problems of flight than Otto Lilienthal, who was born in 1848 at Anklam,
Pomerania, and even from his early school-days dreamed and planned the
conquest of the air. His practical experiments began when, at the age
of thirteen, he and his brother Gustav made wings consisting of wooden
framework covered with linen, which Otto attached to his arms, and then
ran downhill flapping them. In consequence of possible derision on the
part of other boys, Otto confined these experiments for the most part to
moonlit nights, and gained from them some idea of the resistance offered
by flat surfaces to the air. It was in 1867 that the two brothers
began really practical work, experimenting with wings which, from
their design, indicate some knowledge of Besnier and the history of his
gliding experiments; these wings the brothers fastened to their backs,
moving them with their legs after the fashion of one attempting to swim.
Before they had achieved any real success in gliding the Franco-German
war came as an interruption; both brothers served in this campaign,
resuming their experiments in 1871 at the conclusion of hostilities.

The experiments made by the brothers previous to the war had convinced
Otto that previous experimenters in gliding flight had failed through
reliance on empirical conclusions or else through incomplete observation
on their own part, mostly of bird flight. From 1871 onward Otto
Lilenthal (Gustav's interest in the problem was not maintained as was
his brother's) made what is probably the most detailed and accurate
series of observations that has ever been made with regard to the
properties of curved wing surfaces. So far as could be done, Lilienthal
tabulated the amount of air resistance offered to a bird's wing,
ascertaining that the curve is necessary to flight, as offering far more
resistance than a flat surface. Cayley, and others, had already stated
this, but to Lilienthal belongs the honour of being first to put the
statement to effective proof--he made over 2,000 gliding flights
between 1891 and the regrettable end of his experiments; his practical
conclusions are still regarded as part of the accepted theory of
students of flight. In 1889 he published a work on the subject of
gliding flight which stands as data for investigators, and, on the
conclusions embodied in this work, he began to build his gliders and
practice what he had preached, turning from experiment with models to
wings that he could use.

It was in the summer of 1891 that he built his first glider of rods of
peeled willow, over which was stretched strong cotton fabric; with this,
which had a supporting surface of about 100 square feet, Otto Lilienthal
launched himself in the air from a spring board, making glides which, at
first of only a few feet, gradually lengthened. As his experience of
the supporting qualities of the air progressed he gradually altered
his designs until, when Pilcher visited him in the spring of 1895,
he experimented with a glider, roughly made of peeled willow rods and
cotton fabric, having an area of 150 square feet and weighing half a
hundredweight. By this time Lilienthal had moved from his springboard to
a conical artificial hill which he had had thrown up on level ground at
Grosse Lichterfelde, near Berlin. This hill was made with earth taken
from the excavations incurred in constructing a canal, and had a cave
inside in which Lilienthal stored his machines. Pilcher, in his paper
on 'Gliding,' [*] gives an excellent short summary of Lilienthal's
experiments, from which the following extracts are taken:--

[*] Aeronautical Classes, No. 5. Royal Aeronautical Society's
publications.

'At first Lilienthal used to experiment by jumping off a springboard
with a good run. Then he took to practicing on some hills close to
Berlin. In the summer of 1892 he built a flat-roofed hut on the summit
of a hill, from the top of which he used to jump, trying, of course, to
soar as far as possible before landing.... One of the great dangers with
a soaring machine is losing forward speed, inclining the machine too
much down in front, and coming down head first. Lilienthal was the
first to introduce the system of handling a machine in the air merely
by moving his weight about in the machine; he always rested only on his
elbows or on his elbows and shoulders....

'In 1892 a canal was being cut, close to where Lilienthal lived, in the
suburbs of Berlin, and with the surplus earth Lilienthal had a special
hill thrown up to fly from. The country round is as flat as the sea, and
there is not a house or tree near it to make the wind unsteady, so
this was an ideal practicing ground; for practicing on natural hills
is generally rendered very difficult by shifty and gusty winds.... This
hill is 50 feet high, and conical. Inside the hill there is a cave for
the machines to be kept in.... When Lilienthal made a good flight he
used to land 300 feet from the centre of the hill, having come down at
an angle of 1 in 6; but his best flights have been at an angle of about
1 in 10.

'If it is calm, one must run a few steps down the hill, holding the
machine as far back on oneself as possible, when the air will gradually
support one, and one slides off the hill into the air. If there is any
wind, one should face it at starting; to try to start with a side wind
is most unpleasant. It is possible after a great deal of practice to
turn in the air, and fairly quickly. This is accomplished by throwing
one's weight to one side, and thus lowering the machine on that side
towards which one wants to turn. Birds do the same thing--crows and
gulls show it very clearly. Last year Lilienthal chiefly experimented
with double-surfaced machines. These were very much like the old
machines with awnings spread above them.

'The object of making these double-surfaced machines was to get more
surface without increasing the length and width of the machine. This,
of course, it does, but I personally object to any machine in which
the wing surface is high above the weight. I consider that it makes
the machine very difficult to handle in bad weather, as a puff of wind
striking the surface, high above one, has a great tendency to heel the
machine over.

'Herr Lilienthal kindly allowed me to sail down his hill in one of these
double-surfaced machines last June. With the great facility afforded by
his conical hill the machine was handy enough; but I am afraid I should
not be able to manage one at all in the squally districts I have had to
practice in over here.

'Herr Lilienthal came to grief through deserting his old method of
balancing. In order to control his tipping movements more rapidly he
attached a line from his horizontal rudder to his head, so that when he
moved his head forward it would lift the rudder and tip the machine up
in front, and vice versa. He was practicing this on some natural hills
outside Berlin, and he apparently got muddled with the two motions, and,
in trying to regain speed after he had, through a lull in the wind, come
to rest in the air, let the machine get too far down in front, came down
head first and was killed.'

Then in another passage Pilcher enunciates what is the true value of
such experiments as Lilienthal--and, subsequently, he himself--made:
'The object of experimenting with soaring machines,' he says, 'is to
enable one to have practice in starting and alighting and controlling a
machine in the air. They cannot possibly float horizontally in the
air for any length of time, but to keep going must necessarily lose in
elevation. They are excellent schooling machines, and that is all they
are meant to be, until power, in the shape of an engine working a screw
propeller, or an engine working wings to drive the machine forward, is
added; then a person who is used to soaring down a hill with a simple
soaring machine will be able to fly with comparative safety. One can
best compare them to bicycles having no cranks, but on which one could
learn to balance by coming down an incline.'

It was in 1895 that Lilienthal passed from experiment with the monoplane
type of glider to the construction of a biplane glider which, according
to his own account, gave better results than his previous machines.
'Six or seven metres velocity of wind,' he says, 'sufficed to enable
the sailing surface of 18 square metres to carry me almost horizontally
against the wind from the top of my hill without any starting jump. If
the wind is stronger I allow myself to be simply lifted from the point
of the hill and to sail slowly towards the wind. The direction of the
flight has, with strong wind, a strong upwards tendency. I often reach
positions in the air which are much higher than my starting point. At
the climax of such a line of flight I sometimes come to a standstill
for some time, so that I am enabled while floating to speak with the
gentlemen who wish to photograph me, regarding the best position for the
photographing.'

Lilienthal's work did not end with simple gliding, though he did not
live to achieve machine-driven flight. Having, as he considered, gained
sufficient experience with gliders, he constructed a power-driven
machine which weighed altogether about 90 lbs., and this was thoroughly
tested. The extremities of its wings were made to flap, and the driving
power was obtained from a cylinder of compressed carbonic acid gas,
released through a hand-operated valve which, Lilienthal anticipated,
would keep the machine in the air for four minutes. There were certain
minor accidents to the mechanism, which delayed the trial flights, and
on the day that Lilienthal had determined to make his trial he made a
long gliding flight with a view to testing a new form of rudder that--as
Pilcher relates--was worked by movements of his head. His death came
about through the causes that Pilcher states; he fell from a height of
50 feet, breaking his spine, and the next day he died.

It may be said that Lilienthal accomplished as much as any one of the
great pioneers of flying. As brilliant in his conceptions as da Vinci
had been in his, and as conscientious a worker as Borelli, he laid the
foundations on which Pilcher, Chanute, and Professor Montgomery were
able to build to such good purpose. His book on bird flight, published
in 1889, with the authorship credited both to Otto and his brother
Gustav, is regarded as epoch-making; his gliding experiments are no less
entitled to this description.

In England Lilienthal's work was carried on by Percy Sinclair Pilcher,
who, born in 1866, completed six years' service in the British Navy
by the time that he was nineteen, and then went through a course of
engineering, subsequently joining Maxim in his experimental work. It was
not until 1895 that he began to build the first of the series of gliders
with which he earned his plane among the pioneers of flight. Probably
the best account of Pilcher's work is that given in the Aeronautical
Classics issued by the Royal Aeronautical Society, from which the
following account of Pilcher's work is mainly abstracted.[*]

[*] Aeronautical Classes, No. 5. Royal Aeronautical Society
publications.

The 'Bat,' as Pilcher named his first glider, was a monoplane which he
completed before he paid his visit to Lilienthal in 1895. Concerning
this Pilcher stated that he purposely finished his own machine before
going to see Lilienthal, so as to get the greatest advantage from any
original ideas he might have; he was not able to make any trials with
this machine, however, until after witnessing Lilienthal's experiments
and making several glides in the biplane glider which Lilienthal
constructed.


The wings of the 'Bat' formed a pronounced dihedral angle; the tips
being raised 4 feet above the body. The spars forming the entering
edges of the wings crossed each other in the centre and were lashed to
opposite sides of the triangle that served as a mast for the stay-wires
that guyed the wings. The four ribs of each wing, enclosed in pockets
in the fabric, radiated fanwise from the centre, and were each stayed by
three steel piano-wires to the top of the triangular mast, and similarly
to its base. These ribs were bolted down to the triangle at their roots,
and could be easily folded back on to the body when the glider was not
in use. A small fixed vertical surface was carried in the rear. The
framework and ribs were made entirely of Riga pine; the surface fabric
was nainsook. The area of the machine was 150 square feet; its weight
45 lbs.; so that in flight, with Pilcher's weight of 145 lbs. added, it
carried one and a half pounds to the square foot.

Pilcher's first glides, which he carried out on a grass hill on the
banks of the Clyde near Cardross, gave little result, owing to the
exaggerated dihedral angle of the wings, and the absence of a horizontal
tail. The 'Bat 'was consequently reconstructed with a horizontal tail
plane added to the vertical one, and with the wings lowered so that the
tips were only six inches above the level of the body. The machine now
gave far better results; on the first glide into a head wind Pilcher
rose to a height of twelve feet and remained in the the air for a third
of a minute; in the second attempt a rope was used to tow the glider,
which rose to twenty feet and did not come to earth again until nearly
a minute had passed. With experience Pilcher was able to lengthen his
glide and improve his balance, but the dropped wing tips made landing
difficult, and there were many breakages.

In consequence of this Pilcher built a second glider which he named
the 'Beetle,' because, as he said, it looked like one. In this the
square-cut wings formed almost a continuous plane, rigidly fixed to the
central body, which consisted of a shaped girder. These wings were built
up of five transverse bamboo spars, with two shaped ribs running from
fore to aft of each wing, and were stayed overhead to a couple of masts.
The tail, consisting of two discs placed crosswise (the horizontal
one alone being movable), was carried high up in the rear. With the
exception of the wing-spars, the whole framework was built of white
pine. The wings in this machine were actually on a higher level than the
operator's head; the centre of gravity was, consequently, very low, a
fact which, according to Pilcher's own account, made the glider very
difficult to handle. Moreover, the weight of the 'Beetle,' 80 lbs., was
considerable; the body had been very solidly built to enable it to carry
the engine which Pilcher was then contemplating; so that the glider
carried some 225 lbs. with its area of 170 square feet--too great a mass
for a single man to handle with comfort.

It was in the spring of 1896 that Pilcher built his third glider, the
'Gull,' with 300 square feet of area and a weight of 55 lbs. The size of
this machine rendered it unsuitable for experiment in any but very calm
weather, and it incurred such damage when experiments were made in a
breeze that Pilcher found it necessary to build a fourth, which he named
the 'Hawk.' This machine was very soundly built, being constructed of
bamboo, with the exception of the two main transverse beams. The wings
were attached to two vertical masts, 7 feet high, and 8 feet apart,
joined at their summits and their centres by two wooden beams. Each wing
had nine bamboo ribs, radiating from its mast, which was situated at a
distance of 2 feet 6 inches from the forward edge of the wing. Each rib
was rigidly stayed at the top of the mast by three tie-wires, and by a
similar number to the bottom of the mast, by which means the curve of
each wing was maintained uniformly. The tail was formed of a triangular
horizontal surface to which was affixed a triangular vertical surface,
and was carried from the body on a high bamboo mast, which was also
stayed from the masts by means of steel wires, but only on its upper
surface, and it was the snapping of one of these guy wires which caused
the collapse of the tail support and brought about the fatal end of
Pilcher's experiments. In flight, Pilcher's head, shoulders, and the
greater part of his chest projected above the wings. He took up his
position by passing his head and shoulders through the top aperture
formed between the two wings, and resting his forearms on the
longitudinal body members. A very simple form of undercarriage, which
took the weight off the glider on the ground, was fitted, consisting of
two bamboo rods with wheels suspended on steel springs.

Balance and steering were effected, apart from the high degree of
inherent stability afforded by the tail, as in the case of Lilienthal's
glider, by altering the position of the body. With this machine Pilcher
made some twelve glides at Eynsford in Kent in the summer of 1896, and
as he progressed he increased the length of his glides, and also handled
the machine more easily, both in the air and in landing. He was occupied
with plans for fitting an engine and propeller to the 'Hawk,' but, in
these early days of the internal combustion engine, was unable to
get one light enough for his purpose. There were rumours of an engine
weighing 15 lbs. which gave 1 horse-power, and was reported to be in
existence in America, but it could not be traced.

In the spring of 1897 Pilcher took up his gliding experiments again,
obtaining what was probably the best of his glides on June 19th, when he
alighted after a perfectly balanced glide of over 250 yards in length,
having crossed a valley at a considerable height. From his various
experiments he concluded that once the machine was launched in the air
an engine of, at most, 3 horse-power would suffice for the maintenance
of horizontal flight, but he had to allow for the additional weight
of the engine and propeller, and taking into account the comparative
inefficiency of the propeller, he planned for an engine of 4
horse-power. Engine and propeller together were estimated at under 44
lbs. weight, the engine was to be fitted in front of the operator, and
by means of an overhead shaft was to operate the propeller situated
in rear of the wings. 1898 went by while this engine was under
construction. Then in 1899 Pilcher became interested in Lawrence
Hargrave's soaring kites, with which he carried out experiments during
the summer of 1899. It is believed that he intended to incorporate
a number of these kites in a new machine, a triplane, of which the
fragments remaining are hardly sufficient to reconstitute the complete
glider. This new machine was never given a trial. For on September 30th,
1899, at Stamford Hall, Market Harborough, Pilcher agreed to give a
demonstration of gliding flight, but owing to the unfavourable weather
he decided to postpone the trial of the new machine and to experiment
with the 'Hawk,' which was intended to rise from a level field, towed by
a line passing over a tackle drawn by two horses. At the first trial the
machine rose easily, but the tow-line snapped when it was well clear of
the ground, and the glider descended, weighed down through being sodden
with rain. Pilcher resolved on a second trial, in which the glider again
rose easily to about thirty feet, when one of the guy wires of the tail
broke, and the tail collapsed; the machine fell to the ground, turning
over, and Pilcher was unconscious when he was freed from the wreckage.

Hopes were entertained of his recovery, but he died on Monday, October
2nd, 1899, aged only thirty-four. His work in the cause of flying
lasted only four years, but in that time his actual accomplishments were
sufficient to place his name beside that of Lilienthal, with whom he
ranks as one of the greatest exponents of gliding flight.




VIII. AMERICAN GLIDING EXPERIMENTS

While Pilcher was carrying on Lilienthal's work in England, the great
German had also a follower in America; one Octave Chanute, who, in one
of the statements which he has left on the subject of his experiments
acknowledges forty years' interest in the problem of flight, did more
to develop the glider in America than--with the possible exception
of Montgomery--any other man. Chanute had all the practicality of an
American; he began his work, so far as actual gliding was concerned,
with a full-sized glider of the Lilienthal type, just before Lilienthal
was killed. In a rather rare monograph, entitled Experiments in Flying,
Chanute states that he found the Lilienthal glider hazardous and decided
to test the value of an idea of his own; in this he followed the same
general method, but reversed the principle upon which Lilienthal had
depended for maintaining his equilibrium in the air. Lilienthal had
shifted the weight of his body, under immovable wings, as fast and as
far as the sustaining pressure varied under his surfaces; this shifting
was mainly done by moving the feet, as the actions required were small
except when alighting. Chanute's idea was to have the operator remain
seated in the machine in the air, and to intervene only to steer or to
alight; moving mechanism was provided to adjust the wings automatically
in order to restore balance when necessary.

Chanute realised that experiments with models were of little use; in
order to be fully instructive, these experiments should be made with
a full-sized machine which carried its operator, for models seldom fly
twice alike in the open air, and no relation can be gained from them of
the divergent air currents which they have experienced. Chanute's idea
was that any flying machine which might be constructed must be able to
operate in a wind; hence the necessity for an operator to report upon
what occurred in flight, and to acquire practical experience of the work
of the human factor in imitation of bird flight. From this point of
view he conducted his own experiments; it must be noted that he was
over sixty years of age when he began, and, being no longer sufficiently
young and active to perform any but short and insignificant glides, the
courage of the man becomes all the more noteworthy; he set to work to
evolve the state required by the problem of stability, and without any
expectation of advancing to the construction of a flying machine which
might be of commercial value. His main idea was the testing of devices
to secure equilibrium; for this purpose he employed assistants to
carry out the practical work, where he himself was unable to supply the
necessary physical energy.

Together with his assistants he found a suitable place for experiments
among the sandhills on the shore of Lake Michigan, about thirty miles
eastward from Chicago. Here a hill about ninety-five feet high was
selected as a point from which Chanute's gliders could set off; in
practice, it was found that the best observation was to be obtained
from short glides at low speed, and, consequently, a hill which was
only sixty-one feet above the shore of the lake was employed for the
experimental work done by the party.

In the years 1896 and 1897, with parties of from four to six persons,
five full-sized gliders were tried out, and from these two distinct
types were evolved: of these one was a machine consisting of five tiers
of wings and a steering tail, and the other was of the biplane type;
Chanute believed these to be safer than any other machine previously
evolved, solving, as he states in his monograph, the problem of inherent
equilibrium as fully as this could be done. Unfortunately, very few
photographs were taken of the work in the first year, but one view of a
multiple wing-glider survives, showing the machine in flight. In 1897 a
series of photographs was taken exhibiting the consecutive phases of
a single flight; this series of photographs represents the experience
gained in a total of about one thousand glides, but the point of view
was varied so as to exhibit the consecutive phases of one single flight.

The experience gained is best told in Chanute's own words. 'The first
thing,' he says, 'which we discovered practically was that the wind
flowing up a hill-side is not a steadily-flowing current like that of a
river. It comes as a rolling mass, full of tumultuous whirls and eddies,
like those issuing from a chimney; and they strike the apparatus with
constantly varying force and direction, sometimes withdrawing support
when most needed. It has long been known, through instrumental
observations, that the wind is constantly changing in force and
direction; but it needed the experience of an operator afloat on a
gliding machine to realise that this all proceeded from cyclonic action;
so that more was learned in this respect in a week than had previously
been acquired by several years of experiments with models. There was a
pair of eagles, living in the top of a dead tree about two miles from
our tent, that came almost daily to show us how such wind effects are
overcome and utilised. The birds swept in circles overhead on
pulseless wings, and rose high up in the air. Occasionally there was
a side-rocking motion, as of a ship rolling at sea, and then the birds
rocked back to an even keel; but although we thought the action was
clearly automatic, and were willing to learn, our teachers were too
far off to show us just how it was done, and we had to experiment for
ourselves.'

Chanute provided his multiple glider with a seat, but, since each
glide only occupied between eight and twelve seconds, there was little
possibility of the operator seating himself. With the multiple glider a
pair of horizontal bars provided rest for the arms, and beyond these
was a pair of vertical bars which the operator grasped with his hands;
beyond this, the operator was in no way attached to the machine. He
took, at the most, four running steps into the wind, which launched
him in the air, and thereupon he sailed into the wind on a generally
descending course. In the matter of descent Chanute observed the sparrow
and decided to imitate it. 'When the latter,' he says, 'approaches the
street, he throws his body back, tilts his outspread wings nearly square
to the course, and on the cushion of air thus encountered he stops his
speed and drops lightly to the ground. So do all birds. We tried it with
misgivings, but found it perfectly effective. The soft sand was a great
advantage, and even when the experts were racing there was not a single
sprained ankle.'

With the multiple winged glider some two to three hundred glides were
made without any accident either to the man or to the machine, and the
action was found so effective, the principle so sound, that full plans
were published for the benefit of any experimenters who might wish to
improve on this apparatus. The American Aeronautical Annual for 1897
contains these plans; Chanute confessed that some movement on the part
of the operator was still required to control the machine, but it was
only a seventh or a sixth part of the movement required for control of
the Lilienthal type.

Chanute waxed enthusiastic over the possibilities of gliding, concerning
which he remarks that 'There is no more delightful sensation than that
of gliding through the air. All the faculties are on the alert, and
the motion is astonishingly smooth and elastic. The machine responds
instantly to the slightest movement of the operator; the air rushes by
one's ears; the trees and bushes flit away underneath, and the landing
comes all too quickly. Skating, sliding, and bicycling are not to be
compared for a moment to aerial conveyance, in which, perhaps, zest is
added by the spice of danger. For it must be distinctly understood that
there is constant danger in such preliminary experiments. When this
hazard has been eliminated by further evolution, gliding will become a
most popular sport.'

Later experiments proved that the biplane type of glider gave better
results than the rather cumbrous model consisting of five tiers of
planes. Longer and more numerous glides, to the number of seven to eight
hundred, were obtained, the rate of descent being about one in six. The
longest distance traversed was about 120 yards, but Chanute had dreams
of starting from a hill about 200 feet high, which would have given him
gliding flights of 1,200 feet. He remarked that 'In consequence of
the speed gained by running, the initial stage of the flight is nearly
horizontal, and it is thrilling to see the operator pass from thirty to
forty feet overhead, steering his machine, undulating his course, and
struggling with the wind-gusts which whistle through the guy wires. The
automatic mechanism restores the angle of advance when compromised by
variations of the breeze; but when these come from one side and tilt the
apparatus, the weight has to be shifted to right the machine... these
gusts sometimes raise the machine from ten to twenty feet vertically,
and sometimes they strike the apparatus from above, causing it to
descend suddenly. When sailing near the ground, these vicissitudes can
be counteracted by movements of the body from three to four inches; but
this has to be done instantly, for neither wings nor gravity will wait
on meditation. At a height of three hundred or four hundred feet the
regulating mechanism would probably take care of these wind-gusts, as it
does, in fact, for their minor variations. The speed of the machine
is generally about seventeen miles an hour over the ground, and from
twenty-two to thirty miles an hour relative to the air. Constant effort
was directed to keep down the velocity, which was at times fifty-two
miles an hour. This is the purpose of the starting and gliding against
the wind, which thus furnishes an initial velocity without there being
undue speed at the landing. The highest wind we dared to experiment in
blew at thirty-one miles an hour; when the wind was stronger, we waited
and watched the birds.'

Chanute details an amusing little incident which occurred in the course
of experiment with the biplane glider. He says that 'We had taken one
of the machines to the top of the hill, and loaded its lower wings with
sand to hold it while we e went to lunch. A gull came strolling inland,
and flapped full-winged to inspect. He swept several circles above the
machine, stretched his neck, gave a squawk and went off. Presently he
returned with eleven other gulls, and they seemed to hold a conclave
about one hundred feet above the big new white bird which they had
discovered on the sand. They circled round after round, and once in a
while there was a series of loud peeps, like those of a rusty gate, as
if in conference, with sudden flutterings, as if a terrifying suggestion
had been made. The bolder birds occasionally swooped downwards to
inspect the monster more closely; they twisted their heads around to
bring first one eye and then the other to bear, and then they rose
again. After some seven or eight minutes of this performance, they
evidently concluded either that the stranger was too formidable to
tackle, if alive, or that he was not good to eat, if dead, and they flew
off to resume fishing, for the weak point about a bird is his stomach.'

The gliders were found so stable, more especially the biplane form, that
in the end Chanute permitted amateurs to make trials under guidance,
and throughout the whole series of experiments not a single accident
occurred. Chanute came to the conclusion that any young, quick, and
handy man could master a gliding machine almost as soon as he could get
the hang of a bicycle, although the penalty for any mistake would be
much more severe.

At the conclusion of his experiments he decided that neither the
multiple plane nor the biplane type of glider was sufficiently perfected
for the application of motive power. In spite of the amount of automatic
stability that he had obtained he considered that there was yet more to
be done, and he therefore advised that every possible method of securing
stability and safety should be tested, first with models, and then with
full-sized machines; designers, he said, should make a point of practice
in order to make sure of the action, to proportion and adjust the parts
of their machine, and to eliminate hidden defects. Experimental
flight, he suggested, should be tried over water, in order to break any
accidental fall; when a series of experiments had proved the stability
of a glider, it would then be time to apply motive power. He admitted
that such a process would be both costly and slow, but, he said, that
'it greatly diminished the chance of those accidents which bring a whole
line of investigation into contempt.' He saw the flying machine as what
it has, in fact, been; a child of evolution, carried on step by step
by one investigator after another, through the stages of doubt and
perplexity which lie behind the realm of possibility, beyond which is
the present day stage of actual performance and promise of ultimate
success and triumph over the earlier, more cumbrous, and slower forms of
the transport that we know.

Chanute's monograph, from which the foregoing notes have been comprised,
was written soon after the conclusion of his series of experiments. He
does not appear to have gone in for further practical work, but to
have studied the subject from a theoretical view-point and with great
attention to the work done by others. In a paper contributed in 1900
to the American Independent, he remarks that 'Flying machines promise
better results as to speed, but yet will be of limited commercial
application. They may carry mails and reach other inaccessible places,
but they cannot compete with railroads as carriers of passengers or
freight. They will not fill the heavens with commerce, abolish custom
houses, or revolutionise the world, for they will be expensive for
the loads which they can carry, and subject to too many weather
contingencies. Success is, however, probable. Each experimenter has
added something to previous knowledge which his successors can avail of.
It now seems likely that two forms of flying machines, a sporting type
and an exploration type, will be gradually evolved within one or two
generations, but the evolution will be costly and slow, and must be
carried on by well-equipped and thoroughly informed scientific men; for
the casual inventor, who relies upon one or two happy inspirations, will
have no chance of success whatever.'

Follows Professor John J. Montgomery, who, in the true American spirit,
describes his own experiments so well that nobody can possibly do it
better. His account of his work was given first of all in the American
Journal, Aeronautics, in January, 1909, and thence transcribed in the
English paper of the same name in May, 1910, and that account is here
copied word for word. It may, however, be noted first that as far back
as 1860, when Montgomery was only a boy, he was attracted to the study
of aeronautical problems, and in 1883 he built his first machine,
which was of the flapping-wing ornithopter type, and which showed its
designer, with only one experiment, that he must design some other
form of machine if he wished to attain to a successful flight.
Chanute details how, in 1884 and 1885 Montgomery built three gliders,
demonstrating the value of curved surfaces. With the first of these
gliders Montgomery copied the wing of a seagull; with the second he
proved that a flat surface was virtually useless, and with the third
he pivoted his wings as in the Antoinette type of power-propelled
aeroplane, proving to his own satisfaction that success lay in this
direction. His own account of the gliding flights carried out under his
direction is here set forth, being the best description of his work that
can be obtained:--

'When I commenced practical demonstration in my work with aeroplanes
I had before me three points; first, equilibrium; second, complete
control; and third, long continued or soaring flight. In starting I
constructed and tested three sets of models, each in advance of the
other in regard to the continuance of their soaring powers, but all
equally perfect as to equilibrium and control. These models were tested
by dropping them from a cable stretched between two mountain tops, with
various loads, adjustments and positions. And it made no difference
whether the models were dropped upside down or any other conceivable
position, they always found their equilibrium immediately and glided
safely to earth.

'Then I constructed a large machine patterned after the first model, and
with the assistance of three cowboy friends personally made a number of
flights in the steep mountains near San Juan (a hundred miles distant).
In making these flights I simply took the aeroplane and made a running
jump. These tests were discontinued after I put my foot into a squirrel
hole in landing and hurt my leg.

'The following year I commenced the work on a larger scale, by engaging
aeronauts to ride my aeroplane dropped from balloons. During this work I
used five hot-air balloons and one gas balloon, five or six aeroplanes,
three riders--Maloney, Wilkie, and Defolco--and had sixteen applicants
on my list, and had a training station to prepare any when I needed
them.

'Exhibitions were given in Santa Cruz, San Jose, Santa Clara, Oaklands,
and Sacramento. The flights that were made, instead of being haphazard
affairs, were in the order of safety and development. In the first
flight of an aeronaut the aeroplane was so arranged that the rider had
little liberty of action, consequently he could make only a limited
flight. In some of the first flights, the aeroplane did little more than
settle in the air. But as the rider gained experience in each successive
flight I changed the adjustments, giving him more liberty of action, so
he could obtain longer flights and more varied movements in the flights.
But in none of the flights did I have the adjustments so that the riders
had full liberty, as I did not consider that they had the requisite
knowledge and experience necessary for their safety; and hence, none
of my aeroplanes were launched so arranged that the rider could make
adjustments necessary for a full flight.

'This line of action caused a good deal of trouble with aeronauts or
riders, who had unbounded confidence and wanted to make long flights
after the first few trials; but I found it necessary, as they seemed
slow in comprehending the important elements and were willing to
take risks. To give them the full knowledge in these matters I was
formulating plans for a large starting station on the Mount Hamilton
Range from which I could launch an aeroplane capable of carrying two,
one of my aeronauts and myself, so I could teach him by demonstration.
But the disasters consequent on the great earthquake completely stopped
all my work on these lines. The flights that were given were only the
first of the series with aeroplanes patterned after the first model.
There were no aeroplanes constructed according to the two other models,
as I had not given the full demonstration of the workings of the first,
though some remarkable and startling work was done. On one occasion
Maloney, in trying to make a very short turn in rapid flight, pressed
very hard on the stirrup which gives a screw-shape to the wings, and
made a side somersault. The course of the machine was very much like one
turn of a corkscrew. After this movement the machine continued on its
regular course. And afterwards Wilkie, not to be outdone by Maloney,
told his friends he would do the same, and in a subsequent flight made
two side somersaults, one in one direction and the other in an opposite,
then made a deep dive and a long glide, and, when about three hundred
feet in the air, brought the aeroplane to a sudden stop and settled to
the earth. After these antics, I decreased the extent of the possible
change in the form of wing-surface, so as to allow only straight sailing
or only long curves in turning.

'During my work I had a few carping critics that I silenced by this
standing offer: If they would deposit a thousand dollars I would cover
it on this proposition. I would fasten a 150 pound sack of sand in the
rider's seat, make the necessary adjustments, and send up an aeroplane
upside down with a balloon, the aeroplane to be liberated by a time
fuse. If the aeroplane did not immediately right itself, make a flight,
and come safely to the ground, the money was theirs.

'Now a word in regard to the fatal accident. The circumstances are
these: The ascension was given to entertain a military company in which
were many of Maloney's friends, and he had told them he would give the
most sensational flight they ever heard of. As the balloon was rising
with the aeroplane, a guy rope dropping switched around the right wing
and broke the tower that braced the two rear wings and which also gave
control over the tail. We shouted Maloney that the machine was broken,
but he probably did not hear us, as he was at the same time saying,
"Hurrah for Montgomery's airship," and as the break was behind him, he
may not have detected it. Now did he know of the breakage or not, and if
he knew of it did he take a risk so as not to disappoint his friends?
At all events, when the machine started on its flight the rear wings
commenced to flap (thus indicating they were loose), the machine turned
on its back, and settled a little faster than a parachute. When we
reached Maloney he was unconscious and lived only thirty minutes. The
only mark of any kind on him was a scratch from a wire on the side of
his neck. The six attending physicians were puzzled at the cause of his
death. This is remarkable for a vertical descent of over 2,000 feet.'

The flights were brought to an end by the San Francisco earthquake in
April, 1906, which, Montgomery states, 'Wrought such a disaster that I
had to turn my attention to other subjects and let the aeroplane rest
for a time.' Montgomery resumed experiments in 1911 in California, and
in October of that year an accident brought his work to an end. The
report in the American Aeronautics says that 'a little whirlwind caught
the machine and dashed it head on to the ground; Professor Montgomery
landed on his head and right hip. He did not believe himself seriously
hurt, and talked with his year-old bride in the tent. He complained of
pains in his back, and continued to grow worse until he died.'




IX. NOT PROVEN

The early history of flying, like that of most sciences, is replete
with tragedies; in addition to these it contains one mystery concerning
Clement Ader, who was well known among European pioneers in the
development of the telephone, and first turned his attention to the
problems of mechanical flight in 1872. At the outset he favoured the
ornithopter principle, constructing a machine in the form of a bird with
a wing-spread of twenty-six feet; this, according to Ader's conception,
was to fly through the efforts of the operator. The result of such
an attempt was past question and naturally the machine never left the
ground.

A pause of nineteen years ensued, and then in 1886 Ader turned his mind
to the development of the aeroplane, constructing a machine of bat-like
form with a wingspread of about forty-six feet, a weight of eleven
hundred pounds, and a steam-power plant of between twenty and thirty
horse-power driving a four-bladed tractor screw. On October 9th, 1890,
the first trials of this machine were made, and it was alleged to have
flown a distance of one hundred and sixty-four feet. Whatever truth
there may be in the allegation, the machine was wrecked through
deficient equilibrium at the end of the trial. Ader repeated the
construction, and on October 14th, 1897, tried out his third machine
at the military establishment at Satory in the presence of the French
military authorities, on a circular track specially prepared for the
experiment. Ader and his friends alleged that a flight of nearly a
thousand feet was made; again the machine was wrecked at the end of the
trial, and there Ader's practical work may be said to have ended, since
no more funds were forthcoming for the subsidy of experiments.

There is the bald narrative, but it is worthy of some amplification. If
Ader actually did what he claimed, then the position which the Wright
Brothers hold as first to navigate the air in a power-driven plane is
nullified. Although at this time of writing it is not a quarter of a
century since Ader's experiment in the presence of witnesses competent
to judge on his accomplishment, there is no proof either way, and
whether he was or was not the first man to fly remains a mystery in the
story of the conquest of the air.

The full story of Ader's work reveals a persistence and determination to
solve the problem that faced him which was equal to that of Lilienthal.
He began by penetrating into the interior of Algeria after having
disguised himself as an Arab, and there he spent some months in studying
flight as practiced by the vultures of the district. Returning to France
in 1886 he began to construct the 'Eole,' modelling it, not on the
vulture, but in the shape of a bat. Like the Lilienthal and Pilcher
gliders this machine was fitted with wings which could be folded; the
first flight made, as already noted, on October 9th, 1890, took place
in the grounds of the chateau d'Amainvilliers, near Bretz; two
fellow-enthusiasts named Espinosa and Vallier stated that a flight
was actually made; no statement in the history of aeronautics has been
subject of so much question, and the claim remains unproved.

It was in September of 1891 that Ader, by permission of the Minister of
War, moved the 'Eole' to the military establishment at Satory for the
purpose of further trial. By this time, whether he had flown or not,
his nineteen years of work in connection with the problems attendant on
mechanical flight had attracted so much attention that henceforth
his work was subject to the approval of the military authorities, for
already it was recognised that an efficient flying machine would confer
an inestimable advantage on the power that possessed it in the event
of war. At Satory the 'Eole' was alleged to have made a flight of 109
yards, or, according to another account, 164 feet, as stated above, in
the trial in which the machine wrecked itself through colliding with
some carts which had been placed near the track--the root cause of this
accident, however, was given as deficient equilibrium.

Whatever the sceptics may say, there is reason for belief in the
accomplishment of actual flight by Ader with his first machine in the
fact that, after the inevitable official delay of some months, the
French War Ministry granted funds for further experiment. Ader named
his second machine, which he began to build in May, 1892, the 'Avion,'
and--an honour which he well deserve--that name remains in French
aeronautics as descriptive of the power-driven aeroplane up to this day.

This second machine, however, was not a success, and it was not until
1897 that the second 'Avion,' which was the third power-driven aeroplane
of Ader's construction, was ready for trial. This was fitted with
two steam motors of twenty horse-power each, driving two four-bladed
propellers; the wings warped automatically: that is to say, if it
were necessary to raise the trailing edge of one wing on the turn,
the trailing edge of the opposite wing was also lowered by the same
movement; an under-carriage was also fitted, the machine running on
three small wheels, and levers controlled by the feet of the aviator
actuated the movement of the tail planes.

On October the 12th, 1897, the first trials of this 'Avion' were made
in the presence of General Mensier, who admitted that the machine made
several hops above the ground, but did not consider the performance as
one of actual flight. The result was so encouraging, in spite of the
partial failure, that, two days later, General Mensier, accompanied by
General Grillon, a certain Lieutenant Binet, and two civilians named
respectively Sarrau and Leaute, attended for the purpose of giving the
machine an official trial, over which the great controversy regarding
Ader's success or otherwise may be said to have arisen.

We will take first Ader's own statement as set out in a very competent
account of his work published in Paris in 1910. Here are Ader's own
words: 'After some turns of the propellers, and after travelling a few
metres, we started off at a lively pace; the pressure-gauge registered
about seven atmospheres; almost immediately the vibrations of the rear
wheel ceased; a little later we only experienced those of the front
wheels at intervals. 'Unhappily, the wind became suddenly strong, and
we had some difficulty in keeping the "Avion" on the white line. We
increased the pressure to between eight and nine atmospheres, and
immediately the speed increased considerably, and the vibrations of
the wheels were no longer sensible; we were at that moment at the point
marked G in the sketch; the "Avion" then found itself freely supported
by its wings; under the impulse of the wind it continually tended to go
outside the (prepared) area to the right, in spite of the action of
the rudder. On reaching the point V it found itself in a very critical
position; the wind blew strongly and across the direction of the white
line which it ought to follow; the machine then, although still going
forward, drifted quickly out of the area; we immediately put over the
rudder to the left as far as it would go; at the same time increasing
the pressure still more, in order to try to regain the course. The
"Avion" obeyed, recovered a little, and remained for some seconds headed
towards its intended course, but it could not struggle against the wind;
instead of going back, on the contrary it drifted farther and farther
away. And ill-luck had it that the drift took the direction towards
part of the School of Musketry, which was guarded by posts and
barriers. Frightened at the prospect of breaking ourselves against these
obstacles, surprised at seeing the earth getting farther away from under
the "Avion," and very much impressed by seeing it rushing sideways at
a sickening speed, instinctively we stopped everything. What passed
through our thoughts at this moment which threatened a tragic turn would
be difficult to set down. All at once came a great shock, splintering, a
heavy concussion: we had landed.'

Thus speaks the inventor; the cold official mind gives out a different
account, crediting the 'Avion' with merely a few hops, and to-day, among
those who consider the problem at all, there is a little group which
persists in asserting that to Ader belongs the credit of the first
power-driven flight, while a larger group is equally persistent in
stating that, save for a few ineffectual hops, all three wheels of the
machine never left the ground. It is past question that the 'Avion' was
capable of power-driven flight; whether it achieved it or no remains an
unsettled problem.

Ader's work is negative proof of the value of such experiments as
Lilienthal, Pilcher, Chanute, and Montgomery conducted; these four set
to work to master the eccentricities of the air before attempting to
use it as a supporting medium for continuous flight under power; Ader
attacked the problem from the other end; like many other experimenters
he regarded the air as a stable fluid capable of giving such support to
his machine as still water might give to a fish, and he reckoned that he
had only to produce the machine in order to achieve flight. The wrecked
'Avion' and the refusal of the French War Ministry to grant any more
funds for further experiment are sufficient evidence of the need for
working along the lines taken by the pioneers of gliding rather than on
those which Ader himself adopted.

Let it not be thought that in this comment there is any desire to
derogate from the position which Ader should occupy in any study of
the pioneers of aeronautical enterprise. If he failed, he failed
magnificently, and if he succeeded, then the student of aeronautics does
him an injustice and confers on the Brothers Wright an honour which,
in spite of the value of their work, they do not deserve. There was
one earlier than Ader, Alphonse Penaud, who, in the face of a lesser
disappointment than that which Ader must have felt in gazing on the
wreckage of his machine, committed suicide; Ader himself, rendered
unable to do more, remained content with his achievement, and with the
knowledge that he had played a good part in the long search which must
eventually end in triumph. Whatever the world might say, he himself was
certain that he had achieved flight. This, for him, was perforce enough.

Before turning to consideration of the work accomplished by the Brothers
Wright, and their proved conquest of the air, it is necessary first to
sketch as briefly as may be the experimental work of Sir (then Mr) Hiram
Maxim, who, in his book, Artificial and Natural Flight, has given
a fairly complete account of his various experiments. He began by
experimenting with models, with screw-propelled planes so attached to a
horizontal movable arm that when the screw was set in motion the plane
described a circle round a central point, and, eventually, he built a
giant aeroplane having a total supporting area of 1,500 square feet,
and a wing-span of fifty feet. It has been thought advisable to give
a fairly full description of the power plant used to the propulsion
of this machine in the section devoted to engine development. The
aeroplane, as Maxim describes it, had five long and narrow planes
projecting from each side, and a main or central plane of pterygoid
aspect. A fore and aft rudder was provided, and had all the auxiliary
planes been put in position for experimental work a total lifting
surface of 6,000 square feet could have been obtained. Maxim, however,
did not use more than 4,000 square feet of lifting surface even in his
later experiments; with this he judged the machine capable of lifting
slightly under 8,000 lbs. weight, made up of 600 lbs. water in the
boiler and tank, a crew of three men, a supply of naphtha fuel, and the
weight of the machine itself.

Maxim's intention was, before attempting free flight, to get as much
data as possible regarding the conditions under which flight must be
obtained, by what is known in these days as 'taxi-ing'--that is, running
the propellers at sufficient speed to drive the machine along the ground
without actually mounting into the air. He knew that he had an immense
lifting surface and a tremendous amount of power in his engine even when
the total weight of the experimental plant was taken into consideration,
and thus he set about to devise some means of keeping the machine on the
nine foot gauge rail track which had been constructed for the trials. At
the outset he had a set of very heavy cast-iron wheels made on which to
mount the machine, the total weight of wheels, axles, and connections
being about one and a half tons. These were so constructed that the
light flanged wheels which supported the machine on the steel rails
could be lifted six inches above the track, still leaving the heavy
wheels on the rails for guidance of the machine. 'This arrangement,'
Maxim states, 'was tried on several occasions, the machine being run
fast enough to lift the forward end off the track. However, I found
considerable difficulty in starting and stopping quickly on account of
the great weight, and the amount of energy necessary to set such heavy
wheels spinning at a high velocity. The last experiment with these
wheels was made when a head wind was blowing at the rate of about ten
miles an hour. It was rather unsteady, and when the machine was running
at its greatest velocity, a sudden gust lifted not only the front
end, but also the heavy front wheels completely off the track, and the
machine falling on soft ground was soon blown over by the wind.'

Consequently, a safety track was provided, consisting of squared pine
logs, three inches by nine inches, placed about two feet above the steel
way and having a thirty-foot gauge. Four extra wheels were fitted to the
machine on outriggers and so adjusted that, if the machine should
lift one inch clear of the steel rails, the wheels at the ends of the
outriggers would engage the under side of the pine trackway.

The first fully loaded run was made in a dead calm with 150 lbs. steam
pressure to the square inch, and there was no sign of the wheels leaving
the steel track. On a second run, with 230 lbs. steam pressure the
machine seemed to alternate between adherence to the lower and upper
tracks, as many as three of the outrigger wheels engaging at the same
time, and the weight on the steel rails being reduced practically to
nothing. In preparation for a third run, in which it was intended to use
full power, a dynamometer was attached to the machine and the engines
were started at 200 lbs. pressure, which was gradually increased to 310
lbs per square inch. The incline of the track, added to the reading of
the dynamometer, showed a total screw thrust of 2,164 lbs. After the
dynamometer test had been completed, and everything had been made ready
for trial in motion, careful observers were stationed on each side of
the track, and the order was given to release the machine. What follows
is best told in Maxim's own words:--

'The enormous screw-thrust started the engine so quickly that it nearly
threw the engineers off their feet, and the machine bounded over the
track at a great rate. Upon noticing a slight diminution in the
steam pressure, I turned on more gas, when almost instantly the steam
commenced to blow a steady blast from the small safety valve, showing
that the pressure was at least 320 lbs. in the pipes supplying the
engines with steam. Before starting on this run, the wheels that were
to engage the upper track were painted, and it was the duty of one of
my assistants to observe these wheels during the run, while another
assistant watched the pressure gauges and dynagraphs. The first part of
the track was up a slight incline, but the machine was lifted clear
of the lower rails and all of the top wheels were fully engaged on the
upper track when about 600 feet had been covered. The speed rapidly
increased, and when 900 feet had been covered, one of the rear axle
trees, which were of two-inch steel tubing, doubled up and set the rear
end of the machine completely free. The pencils ran completely across
the cylinders of the dynagraphs and caught on the underneath end. The
rear end of the machine being set free, raised considerably above the
track and swayed. At about 1,000 feet, the left forward wheel also got
clear of the upper track, and shortly afterwards the right forward wheel
tore up about 100 feet of the upper track. Steam was at once shut off
and the machine sank directly to the earth, embedding the wheels in the
soft turf without leaving any other marks, showing most conclusively
that the machine was completely suspended in the air before it settled
to the earth. In this accident, one of the pine timbers forming the
upper track went completely through the lower framework of the machine
and broke a number of the tubes, but no damage was done to the machinery
except a slight injury to one of the screws.'

It is a pity that the multifarious directions in which Maxim turned his
energies did not include further development of the aeroplane, for it
seems fairly certain that he was as near solution of the problem as Ader
himself, and, but for the holding-down outer track, which was really the
cause of his accident, his machine would certainly have achieved free
flight, though whether it would have risen, flown and alighted, without
accident, is matter for conjecture.

The difference between experiments with models and with full-sized
machines is emphasised by Maxim's statement to the effect that with
a small apparatus for ascertaining the power required for artificial
flight, an angle of incidence of one in fourteen was most advantageous,
while with a large machine he found it best to increase his angle to one
in eight in order to get the maximum lifting effect on a short run at a
moderate speed. He computed the total lifting effect in the experiments
which led to the accident as not less than 10,000 lbs., in which is
proof that only his rail system prevented free flight.




X. SAMUEL PIERPOINT LANGLEY

Langley was an old man when he began the study of aeronautics, or, as
he himself might have expressed it, the study of aerodromics, since he
persisted in calling the series of machines he built 'Aerodromes,' a
word now used only to denote areas devoted to use as landing spaces for
flying machines; the Wright Brothers, on the other hand, had the great
gift of youth to aid them in their work. Even so it was a great race
between Langley, aided by Charles Manly, and Wilbur and Orville Wright,
and only the persistent ill-luck which dogged Langley from the start to
the finish of his experiments gave victory to his rivals. It has been
proved conclusively in these later years of accomplished flight that the
machine which Langley launched on the Potomac River in October of 1903
was fully capable of sustained flight, and only the accidents incurred
in launching prevented its pilot from being the first man to navigate
the air successfully in a power-driven machine.

The best account of Langley's work is that diffused throughout a weighty
tome issued by the Smithsonian Institution, entitled the Langley Memoir
on Mechanical Flight, of which about one-third was written by Langley
himself, the remainder being compiled by Charles M. Manly, the engineer
responsible for the construction of the first radial aero-engine, and
chief assistant to Langley in his experiments. To give a twentieth
of the contents of this volume in the present short account of the
development of mechanical flight would far exceed the amount of space
that can be devoted even to so eminent a man in aeronautics as S.
P. Langley, who, apart from his achievement in the construction of a
power-driven aeroplane really capable of flight, was a scientist of no
mean order, and who brought to the study of aeronautics the skill of the
trained investigator allied to the inventive resource of the genius.

That genius exemplified the antique saw regarding the infinite capacity
for taking pains, for the Langley Memoir shows that as early as 1891
Langley had completed a set of experiments, lasting through years,
which proved it possible to construct machines giving such a velocity
to inclined surfaces that bodies indefinitely heavier than air could
be sustained upon it and propelled through it at high speed. For full
account (very full) of these experiments, and of a later series leading
up to the construction of a series of 'model aerodromes' capable of
flight under power, it is necessary to turn to the bulky memoir of
Smithsonian origin.

The account of these experiments as given by Langley himself reveals
the humility of the true investigator. Concerning them, Langley remarks
that, 'Everything here has been done with a view to putting a trial
aerodrome successfully in flight within a few years, and thus giving an
early demonstration of the only kind which is conclusive in the eyes of
the scientific man, as well as of the general public--a demonstration
that mechanical flight is possible--by actually flying. All that has
been done has been with an eye principally to this immediate result,
and all the experiments given in this book are to be considered only as
approximations to exact truth. All were made with a view, not to some
remote future, but to an arrival within the compass of a few years at
some result in actual flight that could not be gainsaid or mistaken.'

With a series of over thirty rubber-driven models Langley demonstrated
the practicability of opposing curved surfaces to the resistance of the
air in such a way as to achieve flight, in the early nineties of last
century; he then set about finding the motive power which should permit
of the construction of larger machines, up to man-carrying size. The
internal combustion engine was then an unknown quantity, and he had to
turn to steam, finally, as the propulsive energy for his power plant.
The chief problem which faced him was that of the relative weight and
power of his engine; he harked back to the Stringfellow engine of 1868,
which in 1889 came into the possession of the Smithsonian Institution
as a historical curiosity. Rightly or wrongly Langley concluded on
examination that this engine never had developed and never could
develop more than a tenth of the power attributed to it; consequently
he abandoned the idea of copying the Stringfellow design and set about
making his own engine.

How he overcame the various difficulties that faced him and constructed
a steam-engine capable of the task allotted to it forms a story in
itself, too long for recital here. His first power-driven aerodrome
of model size was begun in November of 1891, the scale of construction
being decided with the idea that it should be large enough to carry an
automatic steering apparatus which would render the machine capable of
maintaining a long and steady flight. The actual weight of the first
model far exceeded the theoretical estimate, and Langley found that a
constant increase of weight under the exigencies of construction was a
feature which could never be altogether eliminated. The machine was made
principally of steel, the sustaining surfaces being composed of silk
stretched from a steel tube with wooden attachments. The first engines
were the oscillating type, but were found deficient in power. This led
to the construction of single-acting inverted oscillating engines with
high and low pressure cylinders, and with admission and exhaust ports
to avoid the complication and weight of eccentric and valves. Boiler and
furnace had to be specially designed; an analysis of sustaining surfaces
and the settlement of equilibrium while in flight had to be overcome,
and then it was possible to set about the construction of the series of
model aerodromes and make test of their 'lift.'

By the time Langley had advanced sufficiently far to consider it
possible to conduct experiments in the open air, even with these models,
he had got to his fifth aerodrome, and to the year 1894. Certain tests
resulted in failure, which in turn resulted in further modifications of
design, mainly of the engines. By February of 1895 Langley reported
that under favourable conditions a lift of nearly sixty per cent of
the flying weight was secured, but although this was much more than
was required for flight, it was decided to postpone trials until two
machines were ready for the test. May, 1896, came before actual trials
were made, when one machine proved successful and another, a later
design, failed. The difficulty with these models was that of securing
a correct angle for launching; Langley records how, on launching one
machine, it rose so rapidly that it attained an angle of sixty degrees
and then did a tail slide into the water with its engines working at
full speed, after advancing nearly forty feet and remaining in the
air for about three seconds. Here, Langley found that he had to obtain
greater rigidity in his wings, owing to the distortion of the form of
wing under pressure, and how he overcame this difficulty constitutes yet
another story too long for the telling here.

Field trials were first attempted in 1893, and Langley blamed his
launching apparatus for their total failure. There was a brief, but at
the same time practical, success in model flight in 1894, extending
to between six and seven seconds, but this only proved the need for
strengthening of the wing. In 1895 there was practically no advance
toward the solution of the problem, but the flights of May 6th and
November 28th, 1896, were notably successful. A diagram given in
Langley's memoir shows the track covered by the aerodrome on these two
flights; in the first of them the machine made three complete circles,
covering a distance of 3,200 feet; in the second, that of November 28th,
the distance covered was 4,200 feet, or about three-quarters of a mile,
at a speed of about thirty miles an hour.

These achievements meant a good deal; they proved mechanically propelled
flight possible. The difference between them and such experiments as
were conducted by Clement Ader, Maxim, and others, lay principally in
the fact that these latter either did or did not succeed in rising into
the air once, and then, either willingly or by compulsion, gave up
the quest, while Langley repeated his experiments and thus attained to
actual proof of the possibilities of flight. Like these others, however,
he decided in 1896 that he would not undertake the construction of a
large man-carrying machine. In addition to a multitude of actual duties,
which left him practically no time available for original research, he
had as an adverse factor fully ten years of disheartening difficulties
in connection with his model machines. It was President McKinley who, by
requesting Langley to undertake the construction and test of a machine
which might finally lead to the development of a flying machine
capable of being used in warfare, egged him on to his final experiment.
Langley's acceptance of the offer to construct such a machine is
contained in a letter addressed from the Smithsonian Institution on
December 12th, 1898, to the Board of Ordnance and Fortification of the
United States War Department; this letter is of such interest as to
render it worthy of reproduction:--

'Gentlemen,--In response to your invitation I repeat what I had the
honour to say to the Board--that I am willing, with the consent of the
Regents of this Institution, to undertake for the Government the further
investigation of the subject of the construction of a flying machine
on a scale capable of carrying a man, the investigation to include the
construction, development and test of such a machine under conditions
left as far as practicable in my discretion, it being understood that my
services are given to the Government in such time as may not be occupied
by the business of the Institution, and without charge.

'I have reason to believe that the cost of the construction will come
within the sum of $50,000.00, and that not more than one-half of that
will be called for in the coming year.

'I entirely agree with what I understand to be the wish of the Board
that privacy be observed with regard to the work, and only when it
reaches a successful completion shall I wish to make public the fact of
its success.

'I attach to this a memorandum of my understanding of some points of
detail in order to be sure that it is also the understanding of the
Board, and I am, gentlemen, with much respect, your obedient servant, S.
P. Langley.'

One of the chief problems in connection with the construction of a
full-sized apparatus was that of the construction of an engine, for it
was realised from the first that a steam power plant for a full-sized
machine could only be constructed in such a way as to make it a constant
menace to the machine which it was to propel. By this time (1898) the
internal combustion engine had so far advanced as to convince Langley
that it formed the best power plant available. A contract was made for
the delivery of a twelve horse-power engine to weigh not more than a
hundred pounds, but this contract was never completed, and it fell to
Charles M. Manly to design the five-cylinder radial engine, of which a
brief account is included in the section of this work devoted to aero
engines, as the power plant for the Langley machine.

The history of the years 1899 to 1903 in the Langley series of
experiments contains a multitude of detail far beyond the scope of
this present study, and of interest mainly to the designer. There were
frames, engines, and propellers, to be considered, worked out, and
constructed. We are concerned here mainly with the completed machine and
its trials. Of these latter it must be remarked that the only two actual
field trials which took place resulted in accidents due to the failure
of the launching apparatus, and not due to any inherent defect in the
machine. It was intended that these two trials should be the first of
a series, but the unfortunate accidents, and the fact that no further
funds were forthcoming for continuance of experiments, prevented
Langley's success, which, had he been free to go through as he intended
with his work, would have been certain.

The best brief description of the Langley aerodrome in its final form,
and of the two attempted trials, is contained in the official report of
Major M. M. Macomb of the United States Artillery Corps, which report is
here given in full:--

                         REPORT

Experiments with working models which were concluded August 8 last
having proved the principles and calculations on which the design of the
Langley aerodrome was based to be correct, the next step was to apply
these principles to the construction of a machine of sufficient size
and power to permit the carrying of a man, who could control the motive
power and guide its flight, thus pointing the way to attaining the final
goal of producing a machine capable of such extensive and precise aerial
flight, under normal atmospheric conditions, as to prove of military or
commercial utility.

Mr C. M. Manly, working under Professor Langley, had, by the summer
of 1903, succeeded in completing an engine-driven machine which under
favourable atmospheric conditions was expected to carry a man for any
time up to half an hour, and to be capable of having its flight directed
and controlled by him.

The supporting surface of the wings was ample, and experiment showed the
engine capable of supplying more than the necessary motive power.

Owing to the necessity of lightness, the weight of the various elements
had to be kept at a minimum, and the factor of safety in construction
was therefore exceedingly small, so that the machine as a whole was
delicate and frail and incapable of sustaining any unusual strain. This
defect was to be corrected in later models by utilising data gathered in
future experiments under varied conditions.

One of the most remarkable results attained was the production of a
gasoline engine furnishing over fifty continuous horse-power for a
weight of 120 lbs.

The aerodrome, as completed and prepared for test, is briefly described
by Professor Langley as 'built of steel, weighing complete about
730 lbs., supported by 1,040 feet of sustaining surface, having two
propellers driven by a gas engine developing continuously over fifty
brake horse-power.'

The appearance of the machine prepared for flight was exceedingly light
and graceful, giving an impression to all observers of being capable of
successful flight.

On October 7 last everything was in readiness, and I witnessed the
attempted trial on that day at Widewater, Va. On the Potomac. The engine
worked well and the machine was launched at about 12.15 p.m. The trial
was unsuccessful because the front guy-post caught in its support on the
launching car and was not released in time to give free flight, as was
intended, but, on the contrary, caused the front of the machine to be
dragged downward, bending the guy-post and making the machine plunge
into the water about fifty yards in front of the house-boat. The machine
was subsequently recovered and brought back to the house-boat. The
engine was uninjured and the frame only slightly damaged, but the four
wings and rudder were practically destroyed by the first plunge and
subsequent towing back to the house-boat.

This accident necessitated the removal of the house-boat to Washington
for the more convenient repair of damages.

On December 8 last, between 4 and 5 p.m., another attempt at a trial was
made, this time at the junction of the Anacostia with the Potomac, just
below Washington Barracks.

On this occasion General Randolph and myself represented the Board of
Ordnance and Fortification. The launching car was released at 4.45 p.m.
being pointed up the Anacostia towards the Navy Yard. My position was
on the tug Bartholdi, about 150 feet from and at right angles to
the direction of proposed flight. The car was set in motion and the
propellers revolved rapidly, the engine working perfectly, but there was
something wrong with the launching. The rear guy-post seemed to drag,
bringing the rudder down on the launching ways, and a crashing, rending
sound, followed by the collapse of the rear wings, showed that the
machine had been wrecked in the launching, just how, it was impossible
for me to see. The fact remains that the rear wings and rudder were
wrecked before the machine was free of the ways. Their collapse deprived
the machine of its support in the rear, and it consequently reared up
in front under the action of the motor, assumed a vertical position,
and then toppled over to the rear, falling into the water a few feet in
front of the boat.

Mr Manly was pulled out of the wreck uninjured and the wrecked
machine--was subsequently placed upon the house-boat, and the whole
brought back to Washington.

From what has been said it will be seen that these unfortunate accidents
have prevented any test of the apparatus in free flight, and the claim
that an engine-driven, man-carrying aerodrome has been constructed lacks
the proof which actual flight alone can give.

Having reached the present stage of advancement in its development, it
would seem highly desirable, before laying down the investigation, to
obtain conclusive proof of the possibility of free flight, not only
because there are excellent reasons to hope for success, but because
it marks the end of a definite step toward the attainment of the final
goal.

Just what further procedure is necessary to secure successful flight
with the large aerodrome has not yet been decided upon. Professor
Langley is understood to have this subject under advisement, and
will doubtless inform the Board of his final conclusions as soon as
practicable.

In the meantime, to avoid any possible misunderstanding, it should be
stated that even after a successful test of the present great aerodrome,
designed to carry a man, we are still far from the ultimate goal, and it
would seem as if years of constant work and study by experts, together
with the expenditure of thousands of dollars, would still be necessary
before we can hope to produce an apparatus of practical utility on these
lines.--Washington, January 6, 1904.

A subsequent report of the Board of ordnance and Fortification to the
Secretary of War embodied the principal points in Major Macomb's report,
but as early as March 3rd, 1904, the Board came to a similar conclusion
to that of the French Ministry of War in respect of Clement Ader's work,
stating that it was not 'prepared to make an additional allotment
at this time for continuing the work.' This decision was in no small
measure due to hostile newspaper criticisms. Langley, in a letter to
the press explaining his attitude, stated that he did not wish to make
public the results of his work till these were certain, in consequence
of which he refused admittance to newspaper representatives, and this
attitude produced a hostility which had effect on the United States
Congress. An offer was made to commercialise the invention, but Langley
steadfastly refused it. Concerning this, Manly remarks that Langley
had 'given his time and his best labours to the world without hope of
remuneration, and he could not bring himself, at his stage of life, to
consent to capitalise his scientific work.'

The final trial of the Langley aerodrome was made on December 8th, 1903;
nine days later, on December 17th, the Wright Brothers made their first
flight in a power-propelled machine, and the conquest of the air was
thus achieved. But for the two accidents that spoilt his trials, the
honour which fell to the Wright Brothers would, beyond doubt, have been
secured by Samuel Pierpoint Langley.




XI. THE WRIGHT BROTHERS

Such information as is given here concerning the Wright Brothers is
derived from the two best sources available, namely, the writings of
Wilbur Wright himself, and a lecture given by Dr Griffith Brewer to
members of the Royal Aeronautical Society. There is no doubt that so
far as actual work in connection with aviation accomplished by the two
brothers is concerned, Wilbur Wright's own statements are the clearest
and best available. Apparently Wilbur was, from the beginning, the
historian of the pair, though he himself would have been the last to
attempt to detract in any way from the fame that his brother's work also
deserves. Throughout all their experiments the two were inseparable,
and their work is one indivisible whole; in fact, in every department
of that work, it is impossible to say where Orville leaves off and where
Wilbur begins.

It is a great story, this of the Wright Brothers, and one worth all the
detail that can be spared it. It begins on the 16th April, 1867, when
Wilbur Wright was born within eight miles of Newcastle, Indiana. Before
Orville's birth on the 19th August, 1871, the Wright family had moved
to Dayton, Ohio, and settled on what is known as the 'West Side' of the
town. Here the brothers grew up, and, when Orville was still a boy in
his teens, he started a printing business, which, as Griffith Brewer
remarks, was only limited by the smallness of his machine and small
quantity of type at his disposal. This machine was in such a state that
pieces of string and wood were incorporated in it by way of repair, but
on it Orville managed to print a boys' paper which gained considerable
popularity in Dayton 'West Side.' Later, at the age of seventeen,
he obtained a more efficient outfit, with which he launched a weekly
newspaper, four pages in size, entitled The West Side News. After three
months' running the paper was increased in size and Wilbur came into
the enterprise as editor, Orville remaining publisher. In 1894 the two
brothers began the publication of a weekly magazine, Snap-Shots, to
which Wilbur contributed a series of articles on local affairs that gave
evidence of the incisive and often sarcastic manner in which he was able
to express himself throughout his life. Dr Griffith Brewer describes him
as a fearless critic, who wrote on matters of local interest in a kindly
but vigorous manner, which did much to maintain the healthy public
municipal life of Dayton.

Editorial and publishing enterprise was succeeded by the formation, just
across the road from the printing works, of the Wright Cycle Company,
where the two brothers launched out as cycle manufacturers with the
'Van Cleve' bicycle, a machine of great local repute for excellence of
construction, and one which won for itself a reputation that lasted long
after it had ceased to be manufactured. The name of the machine was that
of an ancestor of the brothers, Catherine Van Cleve, who was one of the
first settlers at Dayton, landing there from the River Miami on April
1st, 1796, when the country was virgin forest.

It was not until 1896 that the mechanical genius which characterised
the two brothers was turned to the consideration of aeronautics. In that
year they took up the problem thoroughly, studying all the aeronautical
information then in print. Lilienthal's writings formed one basis for
their studies, and the work of Langley assisted in establishing in
them a confidence in the possibility of a solution to the problems of
mechanical flight. In 1909, at the banquet given by the Royal Aero Club
to the Wright Brothers on their return to America, after the series of
demonstration flights carried out by Wilbur Wright on the Continent,
Wilbur paid tribute to the great pioneer work of Stringfellow, whose
studies and achievements influenced his own and Orville's early work. He
pointed out how Stringfellow devised an aeroplane having two propellers
and vertical and horizontal steering, and gave due place to this early
pioneer of mechanical flight.

Neither of the brothers was content with mere study of the work of
others. They collected all the theory available in the books published
up to that time, and then built man-carrying gliders with which to test
the data of Lilienthal and such other authorities as they had consulted.
For two years they conducted outdoor experiments in order to test the
truth or otherwise of what were enunciated as the principles of flight;
after this they turned to laboratory experiments, constructing a wind
tunnel in which they made thousands of tests with models of various
forms of curved planes. From their experiments they tabulated thousands
of readings, which Griffith Brewer remarks as giving results equally
efficient with those of the elaborate tables prepared by learned
institutions.

Wilbur Wright has set down the beginnings of the practical experiments
made by the two brothers very clearly. 'The difficulties,' he says,
'which obstruct the pathway to success in flying machine construction
are of three general classes: (1) Those which relate to the construction
of the sustaining wings; (2) those which relate to the generation and
application of the power required to drive the machine through the air;
(3) those relating to the balancing and steering of the machine after
it is actually in flight. Of these difficulties two are already to
a certain extent solved. Men already know how to construct wings, or
aeroplanes, which, when driven through the air at sufficient speed, will
not only sustain the weight of the wings themselves, but also that of
the engine and the engineer as well. Men also know how to build engines
and' screws of sufficient lightness and power to drive these planes
at sustaining speed. Inability to balance and steer still confronts
students of the flying problem, although nearly ten years have passed
(since Lilienthal's success). When this one feature has been worked out,
the age of flying machines will have arrived, for all other difficulties
are of minor importance.

'The person who merely watches the flight of a bird gathers the
impression that the bird has nothing to think of but the flapping of
its wings. As a matter of fact, this is a very small part of its mental
labour. Even to mention all the things the bird must constantly keep in
mind in order to fly securely through the air would take a considerable
time. If I take a piece of paper and, after placing it parallel with
the ground, quickly let it fall, it will not settle steadily down as
a staid, sensible piece of paper ought to do, but it insists on
contravening every recognised rule of decorum, turning over and darting
hither and thither in the most erratic manner, much after the style of
an untrained horse. Yet this is the style of steed that men must learn
to manage before flying can become an everyday sport. The bird has
learned this art of equilibrium, and learned it so thoroughly that its
skill is not apparent to our sight. We only learn to appreciate it when
we can imitate it.

'Now, there are only two ways of learning to ride a fractious horse: one
is to get on him and learn by actual practice how each motion and trick
may be best met; the other is to sit on a fence and watch the beast
awhile, and then retire to the house and at leisure figure out the best
way of overcoming his jumps and kicks. The latter system is the safer,
but the former, on the whole, turns out the larger proportion of good
riders. It is very much the same in learning to ride a flying machine;
if you are looking for perfect safety you will do well to sit on a fence
and watch the birds, but if you really wish to learn you must mount
a machine and become acquainted with its tricks by actual trial. The
balancing of a gliding or flying machine is very simple in theory. It
merely consists in causing the centre of pressure to coincide with the
centre of gravity.'

These comments are taken from a lecture delivered by Wilbur Wright
before the Western Society of Engineers in September of 1901, under the
presidency of Octave Chanute. In that lecture Wilbur detailed the way
in which he and his brother came to interest themselves in aeronautical
problems and constructed their first glider. He speaks of his own
notice of the death of Lilienthal in 1896, and of the way in which this
fatality roused him to an active interest in aeronautical problems,
which was stimulated by reading Professor Marey's Animal Mechanism, not
for the first time. 'From this I was led to read more modern works, and
as my brother soon became equally interested with myself, we soon passed
from the reading to the thinking, and finally to the working stage. It
seemed to us that the main reason why the problem had remained so long
unsolved was that no one had been able to obtain any adequate practice.
We figured that Lilienthal in five years of time had spent only about
five hours in actual gliding through the air. The wonder was not that he
had done so little, but that he had accomplished so much. It would not
be considered at all safe for a bicycle rider to attempt to ride through
a crowded city street after only five hours' practice, spread out in
bits of ten seconds each over a period of five years; yet Lilienthal
with this brief practice was remarkably successful in meeting the
fluctuations and eddies of wind-gusts. We thought that if some method
could be found by which it would be possible to practice by the hour
instead of by the second there would be hope of advancing the solution
of a very difficult problem. It seemed feasible to do this by building a
machine which would be sustained at a speed of eighteen miles per hour,
and then finding a locality where winds of this velocity were common.
With these conditions a rope attached to the machine to keep it from
floating backward would answer very nearly the same purpose as a
propeller driven by a motor, and it would be possible to practice by the
hour, and without any serious danger, as it would not be necessary to
rise far from the ground, and the machine would not have any forward
motion at all. We found, according to the accepted tables of air
pressure on curved surfaces, that a machine spreading 200 square feet of
wing surface would be sufficient for our purpose, and that places would
easily be found along the Atlantic coast where winds of sixteen to
twenty-five miles were not at all uncommon. When the winds were low it
was our plan to glide from the tops of sandhills, and when they were
sufficiently strong to use a rope for our motor and fly over one spot.
Our next work was to draw up the plans for a suitable machine. After
much study we finally concluded that tails were a source of trouble
rather than of assistance, and therefore we decided to dispense with
them altogether. It seemed reasonable that if the body of the operator
could be placed in a horizontal position instead of the upright, as in
the machines of Lilienthal, Pilcher, and Chanute, the wind resistance
could be very materially reduced, since only one square foot instead of
five would be exposed. As a full half horse-power would be saved by this
change, we arranged to try at least the horizontal position. Then the
method of control used by Lilienthal, which consisted in shifting the
body, did not seem quite as quick or effective as the case required; so,
after long study, we contrived a system consisting of two large surfaces
on the Chanute double-deck plan, and a smaller surface placed a short
distance in front of the main surfaces in such a position that the
action of the wind upon it would counterbalance the effect of the travel
of the centre of pressure on the main surfaces. Thus changes in the
direction and velocity of the wind would have little disturbing effect,
and the operator would be required to attend only to the steering of the
machine, which was to be effected by curving the forward surface up or
down. The lateral equilibrium and the steering to right or left was
to be attained by a peculiar torsion of the main surfaces which was
equivalent to presenting one end of the wings at a greater angle than
the other. In the main frame a few changes were also made in the details
of construction and trussing employed by Mr Chanute. The most important
of these were: (1) The moving of the forward main crosspiece of the
frame to the extreme front edge; (2) the encasing in the cloth of all
crosspieces and ribs of the surfaces; (3) a rearrangement of the wires
used in trussing the two surfaces together, which rendered it possible
to tighten all the wires by simply shortening two of them.'

The brothers intended originally to get 200 square feet of supporting
surface for their glider, but the impossibility of obtaining suitable
material compelled them to reduce the area to 165 square feet, which, by
the Lilienthal tables, admitted of support in a wind of about twenty-one
miles an hour at an angle of three degrees. With this glider they went
in the summer of I 1900 to the little settlement of Kitty Hawk, North
Carolina, situated on the strip of land dividing Albemarle Sound from
the Atlantic. Here they reckoned on obtaining steady wind, and here, on
the day that they completed the machine, they took it out for trial as
a kite with the wind blowing at between twenty-five and thirty miles
an hour. They found that in order to support a man on it the glider
required an angle nearer twenty degrees than three, and even with the
wind at thirty miles an hour they could not get down to the planned
angle of three degrees. 'Later, when the wind was too light to support
the machine with a man on it, they tested it as a kite, working the
rudders by cords. Although they obtained satisfactory results in this
way they realised fully that actual gliding experience was necessary
before the tests could be considered practical.

A series of actual measurements of lift and drift of the machine gave
astonishing results. 'It appeared that the total horizontal pull of the
machine, while sustaining a weight of 52 lbs., was only 8.5 lbs., which
was less than had been previously estimated for head resistance of the
framing alone. Making allowance for the weight carried, it appeared that
the head resistance of the framing was but little more than fifty per
cent of the amount which Mr Chanute had estimated as the head resistance
of the framing of his machine. On the other hand, it appeared sadly
deficient in lifting power as compared with the calculated lift of
curved surfaces of its size... we decided to arrange our machine for the
following year so that the depth of curvature of its surfaces could be
varied at will, and its covering air-proofed.'

After these experiments the brothers decided to turn to practical
gliding, for which they moved four miles to the south, to the Kill Devil
sandhills, the principal of which is slightly over a hundred feet
in height, with an inclination of nearly ten degrees on its main
north-western slope. On the day after their arrival they made about a
dozen glides, in which, although the landings were made at a speed of
more than twenty miles an hour, no injury was sustained either by the
machine or by the operator.

'The slope of the hill was 9.5 degrees, or a drop of one foot in six. We
found that after attaining a speed of about twenty-five to thirty miles
with reference to the wind, or ten to fifteen miles over the ground, the
machine not only glided parallel to the slope of the hill, but greatly
increased its speed, thus indicating its ability to glide on a somewhat
less angle than 9.5 degrees, when we should feel it safe to rise higher
from the surface. The control of the machine proved even better than we
had dared to expect, responding quickly to the slightest motion of the
rudder. With these glides our experiments for the year 1900 closed.
Although the hours and hours of practice we had hoped to obtain finally
dwindled down to about two minutes, we were very much pleased with the
general results of the trip, for, setting out as we did with almost
revolutionary theories on many points and an entirely untried form of
machine, we considered it quite a point to be able to return without
having our pet theories completely knocked on the head by the hard logic
of experience, and our own brains dashed out in the bargain. Everything
seemed to us to confirm the correctness of our original opinions:
(1) That practice is the key to the secret of flying; (2) that it
is practicable to assume the horizontal position; (3) that a smaller
surface set at a negative angle in front of the main bearing surfaces,
or wings, will largely counteract the effect of the fore and aft travel
of the centre of pressure; (4) that steering up and down can be attained
with a rudder without moving the position of the operator's body; (5)
that twisting the wings so as to present their ends to the wind at
different angles is a more prompt and efficient way of maintaining
lateral equilibrium than shifting the body of the operator.'

For the gliding experiments of 1901 it was decided to retain the form of
the 1900 glider, but to increase the area to 308 square feet, which, the
brothers calculated, would support itself and its operator in a wind
of seventeen miles an hour with an angle of incidence of three degrees.
Camp was formed at Kitty Hawk in the middle of July, and on July 27th
the machine was completed and tried for the first time in a wind of
about fourteen miles an hour. The first attempt resulted in landing
after a glide of only a few yards, indicating that the centre of gravity
was too far in front of the centre of pressure. By shifting his position
farther and farther back the operator finally achieved an undulating
flight of a little over 300 feet, but to obtain this success he had to
use full power of the rudder to prevent both stalling and nose-diving.
With the 1900 machine one-fourth of the rudder action had been necessary
for far better control.

Practically all glides gave the same result, and in one the machine rose
higher and higher until it lost all headway. 'This was the position from
which Lilienthal had always found difficulty in extricating himself,
as his machine then, in spite of his greatest exertions, manifested a
tendency to dive downward almost vertically and strike the ground head
on with frightful velocity. In this case a warning cry from the ground
caused the operator to turn the rudder to its full extent and also to
move his body slightly forward. The machine then settled slowly to the
ground, maintaining its horizontal position almost perfectly, and landed
without any injury at all. This was very encouraging, as it showed that
one of the very greatest dangers in machines with horizontal tails had
been overcome by the use of the front rudder. Several glides later the
same experience was repeated with the same result. In the latter case
the machine had even commenced to move backward, but was nevertheless
brought safely to the ground in a horizontal position. On the whole this
day's experiments were encouraging, for while the action of the rudder
did not seem at all like that of our 1900 machine, yet we had escaped
without difficulty from positions which had proved very dangerous
to preceding experimenters, and after less than one minute's actual
practice had made a glide of more than 300 feet, at an angle of
descent of ten degrees, and with a machine nearly twice as large as had
previously been considered safe. The trouble with its control, which
has been mentioned, we believed could be corrected when we should have
located its cause.'

It was finally ascertained that the defect could be remedied by
trussing down the ribs of the whole machine so as to reduce the depth of
curvature. When this had been done gliding was resumed, and after a few
trials glides of 366 and 389 feet were made with prompt response on the
part of the machine, even to small movements of the rudder. The rest of
the story of the gliding experiments of 1901 cannot be better told than
in Wilbur Wright's own words, as uttered by him in the lecture from
which the foregoing excerpts have been made.

'The machine, with its new curvature, never failed to respond promptly
to even small movements of the rudder. The operator could cause it to
almost skim the ground, following the undulations of its surface, or he
could cause it to sail out almost on a level with the starting point,
and, passing high above the foot of the hill, gradually settle down to
the ground. The wind on this day was blowing eleven to fourteen miles
per hour. The next day, the conditions being favourable, the machine
was again taken out for trial. This time the velocity of the wind was
eighteen to twenty-two miles per hour. At first we felt some doubt as to
the safety of attempting free flight in so strong a wind, with a machine
of over 300 square feet and a practice of less than five minutes spent
in actual flight. But after several preliminary experiments we decided
to try a glide. The control of the machine seemed so good that we then
felt no apprehension in sailing boldly forth. And thereafter we made
glide after glide, sometimes following the ground closely and sometimes
sailing high in the air. Mr Chanute had his camera with him and took
pictures of some of these glides, several of which are among those
shown.

'We made glides on subsequent days, whenever the conditions were
favourable. The highest wind thus experimented in was a little over
twelve metres per second--nearly twenty-seven miles per hour.

It had been our intention when building the machine to do the larger
part of the experimenting in the following manner:--When the wind blew
seventeen miles an hour, or more, we would attach a rope to the machine
and let it rise as a kite with the operator upon it. When it should
reach a proper height the operator would cast off the rope and glide
down to the ground just as from the top of a hill. In this way we would
be saved the trouble of carrying the machine uphill after each glide,
and could make at least ten glides in the time required for one in the
other way. But when we came to try it, we found that a wind of seventeen
miles, as measured by Richards' anemometer, instead of sustaining the
machine with its operator, a total weight of 240 lbs., at an angle of
incidence of three degrees, in reality would not sustain the machine
alone--100 lbs.--at this angle. Its lifting capacity seemed scarcely one
third of the calculated amount. In order to make sure that this was not
due to the porosity of the cloth, we constructed two small experimental
surfaces of equal size, one of which was air-proofed and the other left
in its natural state; but we could detect no difference in their lifting
powers. For a time we were led to suspect that the lift of curved
surfaces very little exceeded that of planes of the same size, but
further investigation and experiment led to the opinion that (1) the
anemometer used by us over-recorded the true velocity of the wind by
nearly 15 per cent; (2) that the well-known Smeaton co-efficient of.005
V squared for the wind pressure at 90 degrees is probably too great by
at least 20 per cent; (3) that Lilienthal's estimate that the pressure
on a curved surface having an angle of incidence of 3 degrees equals.545
of the pressure at go degrees is too large, being nearly 50 per
cent greater than very recent experiments of our own with a pressure
testing-machine indicate; (4) that the superposition of the surfaces
somewhat reduced the lift per square foot, as compared with a single
surface of equal area.

'In gliding experiments, however, the amount of lift is of less relative
importance than the ratio of lift to drift, as this alone decides
the angle of gliding descent. In a plane the pressure is always
perpendicular to the surface, and the ratio of lift to drift is
therefore the same as that of the cosine to the sine of the angle of
incidence. But in curved surfaces a very remarkable situation is found.
The pressure, instead of being uniformly normal to the chord of the
arc, is usually inclined considerably in front of the perpendicular.
The result is that the lift is greater and the drift less than if
the pressure were normal. Lilienthal was the first to discover this
exceedingly important fact, which is fully set forth in his book, Bird
Flight the Basis of the Flying Art, but owing to some errors in the
methods he used in making measurements, question was raised by other
investigators not only as to the accuracy of his figures, but even as
to the existence of any tangential force at all. Our experiments confirm
the existence of this force, though our measurements differ considerably
from those of Lilienthal. While at Kitty Hawk we spent much time in
measuring the horizontal pressure on our unloaded machine at various
angles of incidence. We found that at 13 degrees the horizontal pressure
was about 23 lbs. This included not only the drift proper, or horizontal
component of the pressure on the side of the surface, but also the head
resistance of the framing as well. The weight of the machine at the time
of this test was about 108 lbs. Now, if the pressure had been normal to
the chord of the surface, the drift proper would have been to the lift
(108 lbs.) as the sine of 13 degrees is to the cosine of 13 degrees,
or.22 X 108/.97 = 24+ lbs.; but this slightly exceeds the total pull
of 23 pounds on our scales. Therefore it is evident that the average
pressure on the surface, instead of being normal to the chord, was so
far inclined toward the front that all the head resistance of framing
and wires used in the construction was more than overcome. In a wind of
fourteen miles per hour resistance is by no means a negligible factor,
so that tangential is evidently a force of considerable value. In a
higher wind, which sustained the machine at an angle of 10 degrees the
pull on the scales was 18 lbs. With the pressure normal to the chord the
drift proper would have been 17 X 98/.98. The travel of the centre of
pressure made it necessary to put sand on the front rudder to bring
the centres of gravity and pressure into coincidence, consequently the
weight of the machine varied from 98 lbs. to 108 lbs. in the different
tests= 17 lbs., so that, although the higher wind velocity must have
caused an increase in the head resistance, the tangential force still
came within 1 lb. of overcoming it. After our return from Kitty Hawk
we began a series of experiments to accurately determine the amount and
direction of the pressure produced on curved surfaces when acted upon by
winds at the various angles from zero to 90 degrees. These experiments
are not yet concluded, but in general they support Lilienthal in the
claim that the curves give pressures more favourable in amount and
direction than planes; but we find marked differences in the exact
values, especially at angles below 10 degrees. We were unable to obtain
direct measurements of the horizontal pressures of the machine with
the operator on board, but by comparing the distance travelled with the
vertical fall, it was easily calculated that at a speed of 24 miles per
hour the total horizontal resistances of our machine, when bearing
the operator, amounted to 40 lbs., which is equivalent to about 2 1/3
horse-power. It must not be supposed, however, that a motor developing
this power would be sufficient to drive a man-bearing machine. The extra
weight of the motor would require either a larger machine, higher speed,
or a greater angle of incidence in order to support it, and therefore
more power. It is probable, however, that an engine of 6 horse-power,
weighing 100 lbs. would answer the purpose. Such an engine is entirely
practicable. Indeed, working motors of one-half this weight per
horse-power (9 lbs. per horse-power) have been constructed by several
different builders. Increasing the speed of our machine from 24 to 33
miles per hour reduced the total horizontal pressure from 40 to about 35
lbs. This was quite an advantage in gliding, as it made it possible to
sail about 15 per cent farther with a given drop. However, it would
be of little or no advantage in reducing the size of the motor in
a power-driven machine, because the lessened thrust would be
counterbalanced by the increased speed per minute. Some years ago
Professor Langley called attention to the great economy of thrust which
might be obtained by using very high speeds, and from this many were led
to suppose that high speed was essential to success in a motor-driven
machine. But the economy to which Professor Langley called attention was
in foot pounds per mile of travel, not in foot pounds per minute. It
is the foot pounds per minute that fixes the size of the motor. The
probability is that the first flying machines will have a relatively low
speed, perhaps not much exceeding 20 miles per hour, but the problem of
increasing the speed will be much simpler in some respects than that of
increasing the speed of a steamboat; for, whereas in the latter case the
size of the engine must increase as the cube of the speed, in the flying
machine, until extremely high speeds are reached, the capacity of the
motor increases in less than simple ratio; and there is even a decrease
in the fuel per mile of travel. In other words, to double the speed of
a steamship (and the same is true of the balloon type of airship) eight
times the engine and boiler capacity would be required, and four times
the fuel consumption per mile of travel: while a flying machine would
require engines of less than double the size, and there would be an
actual decrease in the fuel consumption per mile of travel. But looking
at the matter conversely, the great disadvantage of the flying machine
is apparent; for in the latter no flight at all is possible unless the
proportion of horse-power to flying capacity is very high; but on
the other hand a steamship is a mechanical success if its ratio of
horse-power to tonnage is insignificant. A flying machine that would fly
at a speed of 50 miles per hour with engines of 1,000 horse-power would
not be upheld by its wings at all at a speed of less than 25 miles
an hour, and nothing less than 500 horse-power could drive it at this
speed. But a boat which could make 40 miles an hour with engines of
1,000 horse-power would still move 4 miles an hour even if the engines
were reduced to 1 horse-power. The problems of land and water travel
were solved in the nineteenth century, because it was possible to begin
with small achievements, and gradually work up to our present success.
The flying problem was left over to the twentieth century, because in
this case the art must be highly developed before any flight of any
considerable duration at all can be obtained.

'However, there is another way of flying which requires no artificial
motor, and many workers believe that success will come first by this
road. I refer to the soaring flight, by which the machine is permanently
sustained in the air by the same means that are employed by soaring
birds. They spread their wings to the wind, and sail by the hour,
with no perceptible exertion beyond that required to balance and steer
themselves. What sustains them is not definitely known, though it is
almost certain that it is a rising current of air. But whether it be a
rising current or something else, it is as well able to support a
flying machine as a bird, if man once learns the art of utilising it.
In gliding experiments it has long been known that the rate of vertical
descent is very much retarded, and the duration of the flight greatly
prolonged, if a strong wind blows UP the face of the hill parallel
to its surface. Our machine, when gliding in still air, has a rate of
vertical descent of nearly 6 feet per second, while in a wind blowing
26 miles per hour up a steep hill we made glides in which the rate of
descent was less than 2 feet per second. And during the larger part of
this time, while the machine remained exactly in the rising current,
THERE WAS NO DESCENT AT ALL, BUT EVEN A SLIGHT RISE. If the operator
had had sufficient skill to keep himself from passing beyond the rising
current he would have been sustained indefinitely at a higher point than
that from which he started. The illustration shows one of these very
slow glides at a time when the machine was practically at a standstill.
The failure to advance more rapidly caused the photographer some trouble
in aiming, as you will perceive. In looking at this picture you will
readily understand that the excitement of gliding experiments does
not entirely cease with the breaking up of camp. In the photographic
dark-room at home we pass moments of as thrilling interest as any in
the field, when the image begins to appear on the plate and it is yet an
open question whether we have a picture of a flying machine or merely a
patch of open sky. These slow glides in rising current probably hold out
greater hope of extensive practice than any other method within man's
reach, but they have the disadvantage of requiring rather strong winds
or very large supporting surfaces. However, when gliding operators
have attained greater skill, they can with comparative safety maintain
themselves in the air for hours at a time in this way, and thus by
constant practice so increase their knowledge and skill that they can
rise into the higher air and search out the currents which enable the
soaring birds to transport themselves to any desired point by first
rising in a circle and then sailing off at a descending angle. This
illustration shows the machine, alone, flying in a wind of 35 miles per
hour on the face of a steep hill, 100 feet high. It will be seen
that the machine not only pulls upward, but also pulls forward in the
direction from which the wind blows, thus overcoming both gravity and
the speed of the wind. We tried the same experiment with a man on it,
but found danger that the forward pull would become so strong, that the
men holding the ropes would be dragged from their insecure foothold on
the slope of the hill. So this form of experimenting was discontinued
after four or five minutes' trial.

'In looking over our experiments of the past two years, with models and
full-size machines, the following points stand out with clearness:--

'1. That the lifting power of a large machine, held stationary in a wind
at a small distance from the earth, is much less than the Lilienthal
table and our own laboratory experiments would lead us to expect. When
the machine is moved through the air, as in gliding, the discrepancy
seems much less marked.

'2. That the ratio of drift to lift in well-shaped surfaces is less at
angles of incidence of 5 degrees to 12 degrees than at an angle of 3
degrees.

'3. That in arched surfaces the centre of pressure at 90 degrees is near
the centre of the surface, but moves slowly forward as the angle becomes
less, till a critical angle varying with the shape and depth of the
curve is reached, after which it moves rapidly toward the rear till the
angle of no lift is found.

'4. That with similar conditions large surfaces may be controlled with
not much greater difficulty than small ones, if the control is effected
by manipulation of the surfaces themselves, rather than by a movement of
the body of the operator.

'5. That the head resistances of the framing can be brought to a point
much below that usually estimated as necessary.

'6. That tails, both vertical and horizontal, may with safety be
eliminated in gliding and other flying experiments.

'7. That a horizontal position of the operator's body may be assumed
without excessive danger, and thus the head resistance reduced to about
one-fifth that of the upright position.

'8. That a pair of superposed, or tandem surfaces, has less lift in
proportion to drift than either surface separately, even after making
allowance for weight and head resistance of the connections.'

Thus, to the end of the 1901 experiments, Wilbur Wright provided a
fairly full account of what was accomplished; the record shows an amount
of patient and painstaking work almost beyond belief--it was no question
of making a plane and launching it, but a business of trial and error,
investigation and tabulation of detail, and the rejection time after
time of previously accepted theories, till the brothers must have felt
the the solid earth was no longer secure, at times. Though it was Wilbur
who set down this and other records of the work done, yet the actual
work was so much Orville's as his brother's that no analysis could
separate any set of experiments and say that Orville did this and Wilbur
that--the two were inseparable. On this point Griffith Brewer remarked
that 'in the arguments, if one brother took one view, the other brother
took the opposite view as a matter of course, and the subject was
thrashed to pieces until a mutually acceptable result remained. I have
often been asked since these pioneer days, "Tell me, Brewer, who was
really the originator of those two?" In reply, I used first to say,
"I think it was mostly Wilbur," and later, when I came to know Orville
better, I said, "The thing could not have been without Orville." Now,
when asked, I have to say, "I don't know," and I feel the more I think
of it that it was only the wonderful combination of these two brothers,
who devoted their lives together or this common object, that made the
discovery of the art of flying possible.'

Beyond the 1901 experiments in gliding, the record grows more scrappy,
less detailed. It appears that once power-driven flight had been
achieved, the brothers were not so willing to talk as before;
considering the amount of work that they put in, there could have been
little time for verbal description of that work--as already remarked,
their tables still stand for the designer and experimenter. The end of
the 1901 experiments left both brothers somewhat discouraged, though
they had accomplished more than any others. 'Having set out with
absolute faith in the existing scientific data, we ere driven to doubt
one thing after another, finally, after two years of experiment, we cast
it all aside, and decided to rely entirely on our own investigations.
Truth and error were everywhere so intimately mixed as to be
indistinguishable.... We had taken up aeronautics as a sport. We
reluctantly entered upon the scientific side of it.'

Yet, driven thus to the more serious aspect of the work, they found in
the step its own reward, for the work of itself drew them on and on, to
the construction of measuring machines for the avoidance of error, and
to the making of series after series of measurements, concerning which
Wilbur wrote in 1908 (in the Century Magazine) that 'after making
preliminary measurements on a great number of different shaped surfaces,
to secure a general understanding of the subject, we began systematic
measurements of standard surfaces, so varied in design as to bring
out the underlying causes of differences noted in their pressures.
Measurements were tabulated on nearly fifty of these at all angles from
zero to 45 degrees, at intervals of 2 1/2 degrees. Measurements were
also secured showing the effects on each other when surfaces are
superposed, or when they follow one another.

'Some strange results were obtained. One surface, with a heavy roll at
the front edge, showed the same lift for all angles from 7 1/2 to 45
degrees. This seemed so anomalous that we were almost ready to doubt our
own measurements, when a simple test was suggested. A weather vane, with
two planes attached to the pointer at an angle of 80 degrees with
each other, was made. According to our table, such a vane would be in
unstable equilibrium when pointing directly into the wind, for if by
chance the wind should happen to strike one plane at 39 degrees and the
other at 41 degrees, the plane with the smaller angle would have the
greater pressure and the pointer would be turned still farther out
of the course of the wind until the two vanes again secured equal
pressures, which would be at approximately 30 and 50 degrees. But the
vane performed in this very manner. Further corroboration of the tables
was obtained in experiments with the new glider at Kill Devil Hill the
next season.

'In September and October, 1902 nearly 1,000 gliding flights were made,
several of which covered distances of over 600 feet. Some, made against
a wind of 36 miles an hour, gave proof of the effectiveness of the
devices for control. With this machine, in the autumn of 1903, we made
a number of flights in which we remained in the air for over a minute,
often soaring for a considerable time in one spot, without any descent
at all. Little wonder that our unscientific assistant should think the
only thing needed to keep it indefinitely in the air would be a coat of
feathers to make it light!'

It was at the conclusion of these experiments of 1903 that the brothers
concluded they had obtained sufficient data from their thousands of
glides and multitude of calculations to permit of their constructing
and making trial of a power-driven machine. The first designs got out
provided for a total weight of 600 lbs., which was to include the weight
of the motor and the pilot; but on completion it was found that there
was a surplus of power from the motor, and thus they had 150 lbs. weight
to allow for strengthening wings and other parts.

They came up against the problem to which Riach has since devoted so
much attention, that of propeller design. 'We had thought of getting the
theory of the screw-propeller from the marine engineers, and then, by
applying our table of air-pressures to their formulae, of designing
air-propellers suitable for our uses. But, so far as we could learn, the
marine engineers possessed only empirical formulae, and the exact action
of the screw propeller, after a century of use, was still very obscure.
As we were not in a position to undertake a long series of practical
experiments to discover a propeller suitable for our machine, it seemed
necessary to obtain such a thorough understanding of the theory of its
reactions as would enable us to design them from calculation alone.
What at first seemed a simple problem became more complex the longer we
studied it. With the machine moving forward, the air flying backward,
the propellers turning sidewise, and nothing standing still, it seemed
impossible to find a starting point from which to trace the various
simultaneous reactions. Contemplation of it was confusing. After long
arguments we often found ourselves in the ludicrous position of each
having been converted to the other's side, with no more agreement than
when the discussion began.

'It was not till several months had passed, and every phase of the
problem had been thrashed over and over, that the various reactions
began to untangle themselves. When once a clear understanding had been
obtained there was no difficulty in designing a suitable propeller, with
proper diameter, pitch, and area of blade, to meet the requirements of
the flier. High efficiency in a screw-propeller is not dependent upon
any particular or peculiar shape, and there is no such thing as a "best"
screw. A propeller giving a high dynamic efficiency when used upon one
machine may be almost worthless when used upon another. The propeller
should in every case be designed to meet the particular conditions of
the machine to which it is to be applied. Our first propellers, built
entirely from calculation, gave in useful work 66 per cent of the power
expended. This was about one-third more than had been secured by Maxim
or Langley.'

Langley had made his last attempt with the 'aerodrome,' and his splendid
failure but a few days before the brothers made their first attempt at
power-driven aeroplane flight. On December 17th, 1903, the machine was
taken out; in addition to Wilbur and Orville Wright, there were present
five spectators: Mr A. D. Etheridge, of the Kill Devil life-saving
station; Mr W. S.Dough, Mr W. C. Brinkley, of Manteo; Mr John Ward, of
Naghead, and Mr John T. Daniels.[*] A general invitation had been given
to practically all the residents in the vicinity, but the Kill Devil
district is a cold area in December, and history had recorded so many
experiments in which machines had failed to leave the ground that
between temperature and scepticism only these five risked a waste of
their time.

[*] This list is as given by Wilbur Wright himself.

And these five were in at the greatest conquest man had made since James
Watt evolved the steam engine--perhaps even a greater conquest than that
of Watt. Four flights in all were made; the first lasted only twelve
seconds, 'the first in the history of the world in which a machine
carrying a man had raised itself into the air by its own power in free
flight, had sailed forward on a level course without reduction of
speed, and had finally landed without being wrecked,' said Wilbur
Wright concerning the achievement.[*] The next two flights were slightly
longer, and the fourth and last of the day was one second short of the
complete minute; it was made into the teeth of a 20 mile an hour wind,
and the distance travelled was 852 feet.

[*] Century Magazine, September, 1908.

This bald statement of the day's doings is as Wilbur Wright himself
has given it, and there is in truth nothing more to say; no amount of
statement could add to the importance of the achievement, and no more
than the bare record is necessary. The faith that had inspired the long
roll of pioneers, from da Vinci onward, was justified at last.

Having made their conquest, the brothers took the machine back to camp,
and, as they thought, placed it in safety. Talking with the little group
of spectators about the flights, they forgot about the machine, and then
a sudden gust of wind struck it. Seeing that it was being overturned,
all made a rush toward it to save it, and Mr Daniels, a man of large
proportions, was in some way lifted off his feet, falling between the
planes. The machine overturned fully, and Daniels was shaken like a die
in a cup as the wind rolled the machine over and over--he came out at
the end of his experience with a series of bad bruises, and no more, but
the damage done to the machine by the accident was sufficient to render
it useless for further experiment that season.

A new machine, stronger and heavier, was constructed by the brothers,
and in the spring of 1904 they began experiments again at Sims
Station, eight miles to the east of Dayton, their home town. Press
representatives were invited for the first trial, and about a dozen
came--the whole gathering did not number more than fifty people. 'When
preparations had been concluded,' Wilbur Wright wrote of this trial, 'a
wind of only three or four miles an hour was blowing--insufficient for
starting on so short a track--but since many had come a long way to
see the machine in action, an attempt was made. To add to the other
difficulty, the engine refused to work properly. The machine, after
running the length of the track, slid off the end without rising into
the air at all. Several of the newspaper men returned next day but were
again disappointed. The engine performed badly, and after a glide of
only sixty feet the machine again came to the ground. Further trial was
postponed till the motor could be put in better running condition. The
reporters had now, no doubt, lost confidence in the machine, though
their reports, in kindness, concealed it. Later, when they heard that
we were making flights of several minutes' duration, knowing that longer
flights had been made with airships, and not knowing any essential
difference between airships and flying machines, they were but little
interested.

'We had not been flying long in 1904 before we found that the problem of
equilibrium had not as yet been entirely solved. Sometimes, in making
a circle, the machine would turn over sidewise despite anything the
operator could do, although, under the same conditions in ordinary
straight flight it could have been righted in an instant. In one flight,
in 1905, while circling round a honey locust-tree at a height of about
50 feet, the machine suddenly began to turn up on one wing, and took a
course toward the tree. The operator, not relishing the idea of landing
in a thorn tree, attempted to reach the ground. The left wing, however,
struck the tree at a height of 10 or 12 feet from the ground and carried
away several branches; but the flight, which had already covered a
distance of six miles, was continued to the starting point.

'The causes of these troubles--too technical for explanation here--were
not entirely overcome till the end of September, 1905. The flights then
rapidly increased in length, till experiments were discontinued after
October 5 on account of the number of people attracted to the field.
Although made on a ground open on every side, and bordered on two sides
by much-travelled thoroughfares, with electric cars passing every hour,
and seen by all the people living in the neighbourhood for miles around,
and by several hundred others, yet these flights have been made by some
newspapers the subject of a great "mystery."'

Viewing their work from the financial side, the two brothers incurred
but little expense in the earlier gliding experiments, and, indeed,
viewed these only as recreation, limiting their expenditure to that
which two men might spend on any hobby. When they had once achieved
successful power-driven flight, they saw the possibilities of their
work, and abandoned such other business as had engaged their energies,
sinking all their capital in the development of a practical flying
machine. Having, in 1905, improved their designs to such an extent that
they could consider their machine a practical aeroplane, they devoted
the years 1906 and 1907 to business negotiations and to the construction
of new machines, resuming flying experiments in May of 1908 in order to
test the ability of their machine to meet the requirements of a contract
they had made with the United States Government, which required an
aeroplane capable of carrying two men, together with sufficient fuel
supplies for a flight of 125 miles at 40 miles per hour. Practically
similar to the machine used in the experiments of 1905, the contract
aeroplane was fitted with a larger motor, and provision was made for
seating a passenger and also for allowing of the operator assuming a
sitting position, instead of lying prone.

Before leaving the work of the brothers to consider contemporary events,
it may be noted that they claimed--with justice--that they were first to
construct wings adjustable to different angles of incidence on the right
and left side in order to control the balance of an aeroplane; the
first to attain lateral balance by adjusting wing-tips to respectively
different angles of incidence on the right and left sides, and the first
to use a vertical vane in combination with wing-tips, adjustable to
respectively different angles of incidence, in balancing and steering
an aeroplane. They were first, too, to use a movable vertical tail, in
combination with wings adjustable to different angles of incidence, in
controlling the balance and direction of an aeroplane.[*]

[*]Aeronautical Journal, No. 79.

A certain Henry M. Weaver, who went to see the work of the brothers,
writing in a letter which was subsequently read before the Aero Club de
France records that he had a talk in 1905 with the farmer who rented the
field in which the Wrights made their flights.' On October 5th (1905) he
was cutting corn in the next field east, which is higher ground. When
he noticed the aeroplane had started on its flight he remarked to his
helper: "Well, the boys are at it again," and kept on cutting corn, at
the same time keeping an eye on the great white form rushing about its
course. "I just kept on shocking corn," he continued, "until I got down
to the fence, and the durned thing was still going round. I thought it
would never stop."'

He was right. The brothers started it, and it will never stop.

Mr Weaver also notes briefly the construction of the 1905 Wright flier.
'The frame was made of larch wood-from tip to tip of the wings the
dimension was 40 feet. The gasoline motor--a special construction
made by them--much the same, though, as the motor on the Pope-Toledo
automobile--was of from 12 to 15 horse-power. The motor weighed 240 lbs.
The frame was covered with ordinary muslin of good quality. No attempt
was made to lighten the machine; they simply built it strong enough
to stand the shocks. The structure stood on skids or runners, like a
sleigh. These held the frame high enough from the ground in alighting
to protect the blades of the propeller. Complete with motor, the machine
weighed 925 lbs.




XII. THE FIRST YEARS OF CONQUEST

It is no derogation of the work accomplished by the Wright Brothers to
say that they won the honour of the first power-propelled flights in
a heavier-than-air machine only by a short period. In Europe, and
especially in France, independent experiment was being conducted by
Ferber, by Santos-Dumont, and others, while in England Cody was not far
behind the other giants of those days. The history of the early years
of controlled power flights is a tangle of half-records; there were no
chroniclers, only workers, and much of what was done goes unrecorded
perforce, since it was not set down at the time.

Before passing to survey of those early years, let it be set down that
in 1907, when the Wright Brothers had proved the practicability of their
machines, negotiations were entered into between the brothers and
the British War office. On April 12th 1907, the apostle of military
stagnation, Haldane, then War Minister, put an end to the negotiations
by declaring that 'the War office is not disposed to enter into
relations at present with any manufacturer of aeroplanes' The state
of the British air service in 1914 at the outbreak of hostilities, is
eloquent regarding the pursuance of the policy which Haldane initiated.

'If I talked a lot,' said Wilbur Wright once, 'I should be like the
parrot, which is the bird that speaks most and flies least.' That
attitude is emblematic of the majority of the early fliers, and because
of it the record of their achievements is incomplete to-day. Ferber,
for instance, has left little from which to state what he did, and that
little is scattered through various periodicals, scrappily enough. A
French army officer, Captain Ferber was experimenting with monoplane
and biplane gliders at the beginning of the century-his work was
contemporary with that of the Wrights. He corresponded both with Chanute
and with the Wrights, and in the end he was commissioned by the
French Ministry of War to undertake the journey to America in order
to negotiate with the Wright Brothers concerning French rights in the
patents they had acquired, and to study their work at first hand.

Ferber's experiments in gliding began in 1899 at the Military School at
Fountainebleau, with a canvas glider of some 80 square feet supporting
surface, and weighing 65 lbs. Two years later he constructed a larger
and more satisfactory machine, with which he made numerous excellent
glides. Later, he constructed an apparatus which suspended a plane from
a long arm which swung on a tower, in order that experiments might be
carried out without risk to the experimenter, and it was not until 1905
that he attempted power-driven free flight. He took up the Voisin design
of biplane for his power-driven flights, and virtually devoted all his
energies to the study of aeronautics. His book, Aviation, its Dawn
and Development, is a work of scientific value--unlike many of his
contemporaries, Ferber brought to the study of the problems of flight a
trained mind, and he was concerned equally with the theoretical problems
of aeronautics and the practical aspects of the subject.

After Bleriot's successful cross-Channel flight, it was proposed to
offer a prize of L1,000 for the feat which C. S. Rolls subsequently
accomplished (starting from the English side of the Channel), a flight
from Boulogne to Dover and back; in place of this, however, an aviation
week at Boulogne was organised, but, although numerous aviators were
invited to compete, the condition of the flying grounds was such that
no competitions took place. Ferber was virtually the only one to do any
flying at Boulogne, and at the outset he had his first accident; after
what was for those days a good flight, he made a series of circles
with his machine, when it suddenly struck the ground, being partially
wrecked. Repairs were carried out, and Ferber resumed his exhibition
flights, carrying on up to Wednesday, September 22nd, 1909. On that day
he remained in the air for half an hour, and, as he was about to land,
the machine struck a mound of earth and overturned, pinning Ferber under
the weight of the motor. After being extricated, Ferber seemed to show
little concern at the accident, but in a few minutes he complained of
great pain, when he was conveyed to the ambulance shed on the ground.

'I was foolish,' he told those who were with him there. 'I was flying
too low. It was my own fault and it will be a severe lesson to me.
I wanted to turn round, and was only five metres from the ground.' A
little after this, he got up from the couch on which he had been placed,
and almost immediately collapsed, dying five minutes later.

Ferber's chief contemporaries in France were Santos-Dumont, of airship
fame, Henri and Maurice Farman, Hubert Latham, Ernest Archdeacon, and
Delagrange. These are names that come at once to mind, as does that of
Bleriot, who accomplished the second great feat of power-driven flight,
but as a matter of fact the years 1903-10 are filled with a little host
of investigators and experimenters, many of whom, although their names
do not survive to any extent, are but a very little way behind those
mentioned here in enthusiasm and devotion. Archdeacon and Gabriel
Voisin, the former of whom took to heart the success achieved by the
Wright Brothers, co-operated in experiments in gliding. Archdeacon
constructed a glider in box-kite fashion, and Voisin experimented with
it on the Seine, the glider being towed by a motorboat to attain the
necessary speed. It was Archdeacon who offered a cup for the first
straight flight of 200 metres, which was won by Santos-Dumont, and he
also combined with Henri Deutsch de la Meurthe in giving the prize for
the first circular flight of a mile, which was won by Henry Farman on
January 13th, 1908.

A history of the development of aviation in France in these, the
strenuous years, would fill volumes in itself. Bleriot was carrying
out experiments with a biplane glider on the Seine, and Robert
Esnault-Pelterie was working on the lines of the Wright Brothers,
bringing American practice to France. In America others besides the
Wrights had wakened to the possibilities of heavier-than-air flight;
Glenn Curtiss, in company with Dr Alexander Graham Bell, with J. A. D.
McCurdy, and with F. W. Baldwin, a Canadian engineer, formed the Aerial
Experiment Company, which built a number of aeroplanes, most famous of
which were the 'June Bug,' the 'Red Wing,' and the 'White Wing.' In 1908
the 'June Bug 'won a cup presented by the Scientific American--it was
the first prize offered in America in connection with aeroplane flight.

Among the little group of French experimenters in these first years of
practical flight, Santos-Dumont takes high rank. He built his 'No. 14
bis' aeroplane in biplane form, with two superposed main plane surfaces,
and fitted it with an eight-cylinder Antoinette motor driving a
two-bladed aluminium propeller, of which the blades were 6 feet only
from tip to tip. The total lift surface of 860 square feet was given
with a wing-span of a little under 40 feet, and the weight of the
complete machine was 353 lbs., of which the engine weighed 158 lbs.
In July of 1906 Santos-Dumont flew a distance of a few yards in this
machine, but damaged it in striking the ground; on October 23rd of the
same year he made a flight of nearly 200 feet--which might have been
longer, but that he feared a crowd in front of the aeroplane and cut
off his ignition. This may be regarded as the first effective flight in
Europe, and by it Santos-Dumont takes his place as one of the chief--if
not the chief--of the pioneers of the first years of practical flight,
so far as Europe is concerned.

Meanwhile, the Voisin Brothers, who in 1904 made cellular kites for
Archdeacon to test by towing on the Seine from a motor launch, obtained
data for the construction of the aeroplane which Delagrange and Henry
Farman were to use later. The Voisin was a biplane, constructed with
due regard to the designs of Langley, Lilienthal, and other earlier
experimenters--both the Voisins and M. Colliex, their engineer, studied
Lilienthal pretty exhaustively in getting out their design, though their
own researches were very thorough as well. The weight of this Voisin
biplane was about 1,450 lbs., and its maximum speed was some 38 to 40
miles per hour, the total supporting surface being about 535 square
feet. It differed from the Wright design in the possession of a
tail-piece, a characteristic which marked all the French school of early
design as in opposition to the American. The Wright machine got its
longitudinal stability by means of the main planes and the elevating
planes, while the Voisin type added a third factor of stability in its
sailplanes. Further, the Voisins fitted their biplane with a wheeled
undercarriage, while the Wright machine, being fitted only with runners,
demanded a launching rail for starting. Whether a machine should be
tailless or tailed was for some long time matter for acute controversy,
which in the end was settled by the fitting of a tail to the Wright
machines-France won the dispute by the concession.

Henry Farman, who began his flying career with a Voisin machine, evolved
from it the aeroplane which bore his name, following the main lines of
the Voisin type fairly closely, but making alterations in the controls,
and in the design of the undercarriage, which was somewhat elaborated,
even to the inclusion of shock absorbers. The seven-cylinder 50
horse-power Gnome rotary engine was fitted to the Farman machine--the
Voisins had fitted an eight-cylinder Antoinette, giving 50 horse-power
at 1,100 revolutions per minute, with direct drive to the propeller.
Farman reduced the weight of the machine from the 1,450 lbs. of the
Voisins to some 1,010 lbs. or thereabouts, and the supporting area to
450 square feet. This machine won its chief fame with Paulhan as pilot
in the famous London to Manchester flight--it is to be remarked, too,
that Farman himself was the first man in Europe to accomplish a flight
of a mile.

Other notable designs of these early days were the 'R.E.P.', Esnault
Pelterie's machine, and the Curtiss-Herring biplane. Of these Esnault
Pelterie's was a monoplane, designed in that form since Esnault Pelterie
had found by experiment that the wire used in bracing offers far more
resistance to the air than its dimensions would seem to warrant. He
built the wings of sufficient strength to stand the strain of flight
without bracing wires, and dependent only for their support on the
points of attachment to the body of the machine; for the rest, it
carried its propeller in front of the planes, and both horizontal and
vertical rudders at the stern--a distinct departure from the Wright
and similar types. One wheel only was fixed under the body where the
undercarriage exists on a normal design, but light wheels were fixed,
one at the extremity of each wing, and there was also a wheel under the
tail portion of the machine. A single lever actuated all the controls
for steering. With a supporting surface of 150 square feet the machine
weighed 946 lbs., about 6.4 lbs. per square foot of lifting surface.

The Curtiss biplane, as flown by Glenn Curtiss at the Rheims meeting,
was built with a bamboo framework, stayed by means of very fine
steel-stranded cables. A--then--novel feature of the machine was the
moving of the ailerons by the pilot leaning to one side or the other in
his seat, a light, tubular arm-rest being pressed by his body when he
leaned to one side or the other, and thus operating the movement of the
ailerons employed for tilting the plane when turning. A steering-wheel
fitted immediately in front of the pilot's seat served to operate a rear
steering-rudder when the wheel was turned in either direction, while
pulling back the wheel altered the inclination of the front elevating
planes, and so gave lifting or depressing control of the plane.

This machine ran on three wheels before leaving the ground, a central
undercarriage wheel being fitted in front, with two more in line with
a right angle line drawn through the centre of the engine crank at the
rear end of the crank-case. The engine was a 35 horsepower Vee design,
water cooled, with overhead inlet and exhaust valves, and Bosch
high-tension magneto ignition. The total weight of the plane in flying
order was about 700 lbs.

As great a figure in the early days as either Ferber or Santos-Dumont
was Louis Bleriot, who, as early as 1900 built a flapping-wing model,
this before ever he came to experimenting with the Voisin biplane type
of glider on the Seine. Up to 1906 he had built four biplanes of his own
design, and in March of 1907 he built his first monoplane, to wreck
it only a few days after completion in an accident from which he had
a fortunate escape. His next machine was a double monoplane, designed
after Langley's precept, to a certain extent, and this was totally
wrecked in September of 1907. His seventh machine, a monoplane, was
built within a month of this accident, and with this he had a number
of mishaps, also achieving some good flights, including one in which
he made a turn. It was wrecked in December of 1907, whereupon he built
another monoplane on which, on July 6th, 1908, Bleriot made a flight
lasting eight and a half minutes. In October of that year he flew the
machine from Toury to Artenay and returned on it--this was just a day
after Farman's first cross-country flight--but, trying to repeat the
success five days later, Bleriot collided with a tree in a fog and
wrecked the machine past repair. Thereupon he set about building his
eleventh machine, with which he was to achieve the first flight across
the English channel.

Henry Farman, to whom reference has already been made, was engaged with
his two brothers, Maurice and Richard, in the motor-car business, and
turned to active interest in flying in 1907, when the Voisin firm built
his first biplane on the box-kite principle. In July of 1908 he won
a prize of L400 for a flight of thirteen miles, previously having
completed the first kilometre flown in Europe with a passenger, the said
passenger being Ernest Archdeaon. In September of 1908 Farman put up a
speed record of forty miles an hour in a flight lasting forty minutes.

Santos-Dumont produced the famous 'Demoiselle' monoplane early in 1909,
a tiny machine in which the pilot had his seat in a sort of miniature
cage under the main plane. It was a very fast, light little machine but
was difficult to fly, and owing to its small wingspread was unable
to glide at a reasonably safe angle. There has probably never been a
cheaper flying machine to build than the 'Demoiselle,' which could be so
upset as to seem completely wrecked, and then repaired ready for further
flight by a couple of hours' work. Santos-Dumont retained no patent
in the design, but gave it out freely to any one who chose to build
'Demoiselles'; the vogue of the pattern was brief, owing to the
difficulty of piloting the machine.

These were the years of records, broken almost as soon as made. There
was Farman's mile, there was the flight of the Comte de Lambert over the
Eiffel Tower, Latham's flight at Blackpool in a high wind, the Rheims
records, and then Henry Farman's flight of four hours later in 1909,
Orville Wright's height record of 1,640 feet, and Delagrange's speed
record of 49.9 miles per hour. The coming to fame of the Gnome rotary
engine helped in the making of these records to a very great extent,
for in this engine was a prime mover which gave the reliability that
aeroplane builders and pilots had been searching for, but vainly. The
Wrights and Glenn Curtiss, of course, had their own designs of engine,
but the Gnome, in spite of its lack of economy in fuel and oil, and its
high cost, soon came to be regarded as the best power plant for flight.

Delagrange, one of the very good pilots of the early days, provided a
curious insight to the way in which flying was regarded, at the opening
of the Juvisy aero aerodrome in May of 1909. A huge crowd had gathered
for the first day's flying, and nine machines were announced to appear,
but only three were brought out. Delagrange made what was considered an
indifferent little flight, and another pilot, one De Bischoff, attempted
to rise, but could not get his machine off the ground. Thereupon the
crowd of 30,000 people lost their tempers, broke down the barriers
surrounding the flying course, and hissed the officials, who were quite
unable to maintain order. Delagrange, however, saved the situation
by making a circuit of the course at a height of thirty feet from the
ground, which won him rounds of cheering and restored the crowd to
good humour. Possibly the smash achieved by Rougier, the famous racing
motorist, who crashed his Voisin biplane after Delagrange had made his
circuit, completed the enjoyment of the spectators. Delagrange, flying
at Argentan in June of 1909, made a flight of four kilometres at a
height of sixty feet; for those days this was a noteworthy performance.
Contemporary with this was Hubert Latham's flight of an hour and seven
minutes on an Antoinette monoplane; this won the adjective 'magnificent'
from contemporary recorders of aviation.

Viewing the work of the little group of French experimenters, it is,
at this length of time from their exploits, difficult to see why
they carried the art as far as they did. There was in it little of
satisfaction, a certain measure of fame, and practically no profit--the
giants of those days got very little for their pains. Delagrange's
experience at the opening of the Juvisy ground was symptomatic of the
way in which flight was regarded by the great mass of people--it was a
sport, and nothing more, but a sport without the dividends attaching
to professional football or horse-racing. For a brief period, after the
Rheims meeting, there was a golden harvest to be reaped by the best of
the pilots. Henry Farman asked L2,000 for a week's exhibition flying in
England, and Paulhan asked half that sum, but a rapid increase in
the number of capable pilots, together with the fact that most flying
meetings were financial failures, owing to great expense in organisation
and the doubtful factor of the weather, killed this goose before many
golden eggs had been gathered in by the star aviators. Besides, as
height and distance records were broken one after another, it became
less and less necessary to pay for entrance to an aerodrome in order to
see a flight--the thing grew too big for a mere sports ground.

Long before Rheims and the meeting there, aviation had grown too big for
the chronicling of every individual effort. In that period of the first
days of conquest of the air, so much was done by so many whose names
are now half-forgotten that it is possible only to pick out the great
figures and make brief reference to their achievements and the machines
with which they accomplished so much, pausing to note such epoch-making
events as the London-Manchester flight, Bleriot's Channel crossing,
and the Rheims meeting itself, and then passing on beyond the days of
individual records to the time when the machine began to dominate the
man. This latter because, in the early days, it was heroism to trust
life to the planes that were turned out--the 'Demoiselle' and the
Antoinette machine that Latham used in his attempt to fly the Channel
are good examples of the flimsiness of early types--while in the later
period, that of the war and subsequently, the heroism turned itself in a
different--and nobler-direction. Design became standardised, though
not perfected. The domination of the machine may best be expressed by
contrasting the way in which machines came to be regarded as compared
with the men who flew them: up to 1909, flying enthusiasts talked of
Farman, of Bleriot, of Paulhan, Curtiss, and of other men; later, they
began to talk of the Voisin, the Deperdussin, and even to the Fokker,
the Avro, and the Bristol type. With the standardising of the machine,
the days of the giants came to an end.




XIII. FIRST FLIERS IN ENGLAND

Certain experiments made in England by Mr Phillips seem to have come
near robbing the Wright Brothers of the honour of the first flight;
notes made by Colonel J. D. Fullerton on the Phillips flying machine
show that in 1893 the first machine was built with a length of 25 feet,
breadth of 22 feet, and height of 11 feet, the total weight, including a
72 lb. load, being 420 lbs. The machine was fitted with some fifty wood
slats, in place of the single supporting surface of the monoplane or two
superposed surfaces of the biplane, these slats being fixed in a steel
frame so that the whole machine rather resembled a Venetian blind. A
steam engine giving about 9 horse-power provided the motive power for
the six-foot diameter propeller which drove the machine. As it was
not possible to put a passenger in control as pilot, the machine was
attached to a central post by wire guys and run round a circle 100
feet in diameter, the track consisting of wooden planking 4 feet wide.
Pressure of air under the slats caused the machine to rise some two or
three feet above the track when sufficient velocity had been attained,
and the best trials were made on June 19th 1893, when at a speed of 40
miles an hour, with a total load of 385 lbs., all the wheels were off
the ground for a distance of 2,000 feet.

In 1904 a full-sized machine was constructed by Mr Phillips, with a
total weight, including that of the pilot, of 600 lbs. The machine was
designed to lift when it had attained a velocity of 50 feet per
second, the motor fitted giving 22 horse-power. On trial, however, the
longitudinal equilibrium was found to be defective, and a further design
was got out, the third machine being completed in 1907. In this the wood
slats were held in four parallel container frames, the weight of the
machine, excluding the pilot, being 500 lbs. A motor similar to that
used in the 1904 machine was fitted, and the machine was designed to
lift at a velocity of about 30 miles an hour, a seven-foot propeller
doing the driving. Mr Phillips tried out this machine in a field about
400 yards across. 'The machine was started close to the hedge, and rose
from the ground when about 200 yards had been covered. When the machine
touched the ground again, about which there could be no doubt, owing to
the terrific jolting, it did not run many yards. When it came to rest I
was about ten yards from the boundary. Of course, I stopped the engine
before I commenced to descend.'[*]

[*] Aeronautical Journal, July, 1908.

S. F. Cody, an American by birth, aroused the attention not only of the
British public, but of the War office and Admiralty as well, as early as
1905 with his man-lifting kites. In that year a height of 1,600 feet was
reached by one of these box-kites, carrying a man, and later in the same
year one Sapper Moreton, of the Balloon Section of the Royal Engineers
(the parent of the Royal Flying Corps) remained for an hour at an
altitude of 2,600 feet. Following on the success of these kites, Cody
constructed an aeroplane which he designated a 'power kite,' which
was in reality a biplane that made the first flight in Great Britain.
Speaking before the Aeronautical Society in 1908, Cody said that 'I have
accomplished one thing that I hoped for very much, that is, to be the
first man to fly in Great Britain.... I made a machine that left the
ground the first time out; not high, possibly five or six inches only. I
might have gone higher if I wished. I made some five flights in all, and
the last flight came to grief.... On the morning of the accident I
went out after adjusting my propellers at 8 feet pitch running at 600
(revolutions per minute). I think that I flew at about twenty-eight
miles per hour. I had 50 horsepower motor power in the engine. A bunch
of trees, a flat common above these trees, and from this flat there is a
slope goes down... to another clump of trees. Now, these clumps of trees
are a quarter of a mile apart or thereabouts.... I was accused of doing
nothing but jumping with my machine, so I got a bit agitated and went to
fly.

I went out this morning with an easterly wind, and left the ground at
the bottom of the hill and struck the ground at the top, a distance of
74 yards. That proved beyond a doubt that the machine would fly--it
flew uphill. That was the most talented flight the machine did, in my
opinion. Now, I turned round at the top and started the machine and left
the ground--remember, a ten mile wind was blowing at the time. Then, 60
yards from where the men let go, the machine went off in this direction
(demonstrating)--I make a line now where I hoped to land--to cut these
trees off at that side and land right off in here. I got here somewhat
excited, and started down and saw these trees right in front of me. I
did not want to smash my head rudder to pieces, so I raised it again and
went up. I got one wing direct over that clump of trees, the right wing
over the trees, the left wing free; the wind, blowing with me, had to
lift over these trees. So I consequently got a false lift on the right
side and no lift on the left side. Being only about 8 feet from the
tree tops, that turned my machine up like that (demonstrating). This
end struck the ground shortly after I had passed the trees. I pulled the
steering handle over as far as I could. Then I faced another bunch of
trees right in front of me. Trying to avoid this second bunch of trees I
turned the rudder, and turned it rather sharp. That side of the machine
struck, and it crumpled up like so much tissue paper, and the machine
spun round and struck the ground that way on, and the framework was
considerably wrecked. Now, I want to advise all aviators not to try
to fly with the wind and to cross over any big clump of earth or any
obstacle of any description unless they go square over the top of it,
because the lift is enormous crossing over anything like that, and in
coming the other way against the wind it would be the same thing when
you arrive at the windward side of the obstacle. That is a point I did
not think of, and had I thought of it I would have been more cautious.'

This Cody machine was a biplane with about 40 foot span, the wings being
about 7 feet in depth with about 8 feet between upper and lower wing
surfaces. 'Attached to the extremities of the lower planes are two small
horizontal planes or rudders, while a third small vertical plane is
fixed over the centre of the upper plane.' The tail-piece and principal
rudder were fitted behind the main body of the machine, and a horizontal
rudder plane was rigged out in front, on two supporting arms extending
from the centre of the machine. The small end-planes and the vertical
plane were used in conjunction with the main rudder when turning to
right or left, the inner plane being depressed on the turn, and the
outer one correspondingly raised, while the vertical plane, working in
conjunction, assisted in preserving stability. Two two-bladed propellers
were driven by an eight-cylinder 50 horse-power Antoinette motor. With
this machine Cody made his first flights over Laffan's plain, being then
definitely attached to the Balloon Section of the Royal Engineers as
military aviation specialist.

There were many months of experiment and trial, after the accident which
Cody detailed in the statement given above, and then, on May 14th, 1909,
Cody took the air and made a flight of 1,200 yards with entire success.
Meanwhile A. V. Roe was experimenting at Lea Marshes with a triplane
of rather curious design the pilot having his seat between two sets of
three superposed planes, of which the front planes could be tilted and
twisted while the machine was in motion. He comes but a little way after
Cody in the chronology of early British experimenters, but Cody, a born
inventor, must be regarded as the pioneer of the present century so
far as Britain is concerned. He was neither engineer nor trained
mathematician, but he was a good rule-of-thumb mechanic and a man of
pluck and perseverance; he never strove to fly on an imperfect machine,
but made alteration after alteration in order to find out what was
improvement and what was not, in consequence of which it was said of him
that he was 'always satisfied with his alterations.'

By July of 1909 he had fitted an 80 horse-power motor to his biplane,
and with this he made a flight of over four miles over Laffan's Plain on
July 21st. By August he was carrying passengers, the first being Colonel
Capper of the R.E. Balloon Section, who flew with Cody for over
two miles, and on September 8th, 1909, he made a world's record
cross-country flight of over forty miles in sixty-six minutes, taking
a course from Laffan's Plain over Farnborough, Rushmoor, and Fleet,
and back to Laffan's Plain. He was one of the competitors in the 1909
Doncaster Aviation Meeting, and in 1910 he competed at Wolverhampton,
Bournemouth, and Lanark. It was on June 7th, 1910, that he qualified for
his brevet, No. 9, on the Cody biplane.

He built a machine which embodied all the improvements for which he had
gained experience, in 1911, a biplane with a length of 35 feet and
span of 43 feet, known as the 'Cody cathedral' on account of its
rather cumbrous appearance. With this, in 1911, he won the two Michelin
trophies presented in England, completed the Daily Mail circuit of
Britain, won the Michelin cross-country prize in 1912 and altogether, by
the end of 1912, had covered more than 7,000 miles with the machine.
It was fitted with a 120 horse-power Austro-Daimler engine, and was
characterised by an exceptionally wide range of speed--the great
wingspread gave a slow landing speed.

A few of his records may be given: in 1910, flying at Laffan's Plain in
his biplane, fitted with a 50-60 horsepower Green engine, on December
31st, he broke the records for distance and time by flying 185 miles,
787 yards, in 4 hours 37 minutes. On October 31st, 1911, he beat this
record by flying for 5 hours 15 minutes, in which period he covered
261 miles 810 yards with a 60 horse-power Green engine fitted to his
biplane. In 1912, competing in the British War office tests of military
aeroplanes, he won the L5,000 offered by the War Office. This was in
competition with no less than twenty-five other machines, among which
were the since-famous Deperdussin, Bristol, Flanders, and Avro types,
as well as the Maurice Farman and Bleriot makes of machine. Cody's
remarkable speed range was demonstrated in these trials, the speeds of
his machine varying between 72.4 and 48.5 miles per hour. The machine
was the only one delivered for the trials by air, and during the three
hours' test imposed on all competitors a maximum height of 5,000 feet
was reached, the first thousand feet being achieved in three and a half
minutes.

During the summer of 1913 Cody put his energies into the production of
a large hydro-biplane, with which he intended to win the L5,000 prize
offered by the Daily Mail to the first aviator to fly round Britain on
a waterplane. This machine was fitted with landing gear for its tests,
and, while flying it over Laffan's Plain on August 7th, 1913, with Mr W.
H. B. Evans as passenger, Cody met with the accident that cost both
him and his passenger their lives. Aviation lost a great figure by his
death, for his plodding, experimenting, and dogged courage not only won
him the fame that came to a few of the pilots of those days, but also
advanced the cause of flying very considerably and contributed not a
little to the sum of knowledge in regard to design and construction.

Another figure of the early days was A. V. Roe, who came from marine
engineering to the motor industry and aviation in 1905. In 1906 he went
out to Colorado, getting out drawings for the Davidson helicopter, and
in 1907 having returned to England, he obtained highest award out of 200
entries in a model aeroplane flying competition. From the design of
this model he built a full-sized machine, and made a first flight on it,
fitted with a 24 horse-power Antoinette engine, in June of 1908 Later,
he fitted a 9 horsepower motor-cycle engine to a triplane of his own
design, and with this made a number of short flights; he got his flying
brevet on a triplane with a motor of 35 horse-power, which, together
with a second triplane, was entered for the Blackpool aviation meeting
of 1910 but was burnt in transport to the meeting. He was responsible
for the building of the first seaplane to rise from English waters, and
may be counted the pioneer of the tractor type of biplane. In 1913 he
built a two-seater tractor biplane with 80 horse-power engine, a machine
which for some considerable time ranked as a leader of design. Together
with E. V. Roe and H. V. Roe, 'A. V.' controlled the Avro works, which
produced some of the most famous training machines of the war period in
a modification of the original 80 horse-power tractor. The first of the
series of Avro tractors to be adopted by the military authorities was
the 1912 biplane, a two-seater fitted with 50 horsepower engine. It was
the first tractor biplane with a closed fuselage to be used for military
work, and became standard for the type. The Avro seaplane, of I 100
horse-power (a fourteen-cylinder Gnome engine was used) was taken up
by the British Admiralty in 1913. It had a length of 34 feet and a
wing-span of 50 feet, and was of the twin-float type.

Geoffrey de Havilland, though of later rank, counts high among designers
of British machines. He qualified for his brevet as late as February,
1911, on a biplane of his own construction, and became responsible for
the design of the BE2, the first successful British Government biplane.
On this he made a British height record of 10,500 feet over Salisbury
Plain, in August of 1912, when he took up Major Sykes as passenger. In
the war period he was one of the principal designers of fighting and
reconnaissance machines.

F. Handley Page, who started in business as an aeroplane builder in
1908, having works at Barking, was one of the principal exponents of
the inherently stable machine, to which he devoted practically all his
experimental work up to the outbreak of war. The experiments were made
with various machines, both of monoplane and biplane type, and of these
one of the best was a two-seater monoplane built in 1911, while a second
was a larger machine, a biplane, built in 1913 and fitted with a 110
horse-power Anzani engine. The war period brought out the giant biplane
with which the name of Handley Page is most associated, the twin-engined
night-bomber being a familiar feature of the later days of the war;
the four-engined bomber had hardly had a chance of proving itself under
service conditions when the war came to an end.

Another notable figure of the early period was 'Tommy' Sopwith, who took
his flying brevet at Brooklands in November of 1910, and within four
days made the British duration record of 108 miles in 3 hours 12
minutes. On December 18th, 1910, he won the Baron de Forrest prize of
L4,000 for the longest flight from England to the Continent, flying
from Eastchurch to Tirlemont, Belgium, in three hours, a distance of 161
miles. After two years of touring in America, he returned to England and
established a flying school. In 1912 he won the first aerial Derby, and
in 1913 a machine of his design, a tractor biplane, raised the British
height record to 13,000 feet (June 16th, at Brooklands). First as
aviator, and then as designer, Sopwith has done much useful work in
aviation.

These are but a few, out of a host who contributed to the development of
flying in this country, for, although France may be said to have set
the pace as regards development, Britain was not far behind. French
experimenters received far more Government aid than did the early
British aviators and designers--in the early days the two were
practically synonymous, and there are many stories of the very early
days at Brooklands, where, when funds ran low, the ardent spirits
patched their trousers with aeroplane fabric and went on with their work
with Bohemian cheeriness. Cody, altering and experimenting on Laffan's
Plain, is the greatest figure of them all, but others rank, too, as
giants of the early days, before the war brought full recognition of the
aeroplane's potentialities.

One of the first men actually to fly in England, Mr J. C. T.
Moore-Brabazon, was a famous figure in the days of exhibition flying,
and won his reputation mainly through being first to fly a circular
mile on a machine designed and built in Great Britain and piloted by a
British subject. Moore-Brabazon's earliest flights were made in France
on a Voisin biplane in 1908, and he brought this machine over to
England, to the Aero Club grounds at Shellness, but soon decided that he
would pilot a British machine instead. An order was placed for a Short
machine, and this, fitted with a 50-60 horse-power Green engine, was
used for the circular mile, which won a prize of L1,000 offered by the
Daily Mail, the feat being accomplished on October 30th, 1909. Five
days later, Moore-Brabazon achieved the longest flight up to that time
accomplished on a British-built machine, covering three and a half
miles. In connection with early flying in England, it is claimed that A.
V. Roe, flying 'Avro B,',' on June 8th, 1908, was actually the first man
to leave the ground, this being at Brooklands, but in point of fact Cody
antedated him.

No record of early British fliers could be made without the name of C.
S. Rolls, a son of Lord Llangattock, on June 2nd, 1910, he flew across
the English Channel to France, until he was duly observed over French
territory, when he returned to England without alighting. The trip was
made on a Wright biplane, and was the third Channel crossing by air,
Bleriot having made the first, and Jacques de Lesseps the second. Rolls
was first to make the return journey in one trip. He was eventually
killed through the breaking of the tail-plane of his machine in
descending at a flying meeting at Bournemouth. The machine was a Wright
biplane, but the design of the tail-plane--which, by the way, was
an addition to the machine, and was not even sanctioned by the
Wrights--appears to have been carelessly executed, and the plane itself
was faulty in construction. The breakage caused the machine to overturn,
killing Rolls, who was piloting it.




XIV. RHEIMS, AND AFTER

The foregoing brief--and necessarily incomplete--survey of the early
British group of fliers has taken us far beyond some of the great events
of the early days of successful flight, and it is necessary to go back
to certain landmarks in the history of aviation, first of which is the
great meeting at Rheims in 1909. Wilbur Wright had come to Europe,
and, flying at Le Mans and Pau--it was on August 8th, 1908, that Wilbur
Wright made the first of his ascents in Europe--had stimulated public
interest in flying in France to a very great degree. Meanwhile, Orville
Wright, flying at Fort Meyer, U.S.A., with Lieutenant Selfridge as a
passenger, sustained an accident which very nearly cost him his life
through the transmission gear of the motor breaking. Selfridge was
killed and Orville Wright was severely injured--it was the first fatal
accident with a Wright machine.

Orville Wright made a flight of over an hour on September 9th, 1908, and
on December 31st of that year Wilbur flew for 2 hours 19 minutes. Thus,
when the Rheims meeting was organised--more notable because it was the
first of its kind, there were already records waiting to be broken. The
great week opened on August 22nd, there being thirty entrants, including
all the most famous men among the early fliers in France. Bleriot,
fresh from his Channel conquest, was there, together with Henry Farman,
Paulhan, Curtiss, Latham, and the Comte de Lambert, first pupil of the
Wright machine in Europe to achieve a reputation as an aviator.

'To say that this week marks an epoch in the history of the world is to
state a platitude. Nevertheless, it is worth stating, and for us who
are lucky enough to be at Rheims during this week there is a solid
satisfaction in the idea that we are present at the making of history.
In perhaps only a few years to come the competitions of this week may
look pathetically small and the distances and speeds may appear paltry.
Nevertheless, they are the first of their kind, and that is sufficient.'

So wrote a newspaper correspondent who was present at the famous
meeting, and his words may stand, being more than mere journalism; for
the great flying week which opened on August 22nd, 1909, ranks as one of
the great landmarks in the history of heavier-than-air flight. The day
before the opening of the meeting a downpour of rain spoilt the flying
ground; Sunday opened with a fairly high wind, and in a lull M.
Guffroy turned out on a crimson R.E.P. monoplane, but the wheels of
his undercarriage stuck in the mud and prevented him from rising in
the quarter of an hour allowed to competitors to get off the ground.
Bleriot, following, succeeded in covering one side of the triangular
course, but then came down through grit in the carburettor. Latham,
following him with thirteen as the number of his machine, experienced
his usual bad luck and came to earth through engine trouble after a very
short flight. Captain Ferber, who, owing to military regulations, always
flew under the name of De Rue, came out next with his Voisin biplane,
but failed to get off the ground; he was followed by Lefebvre on a
Wright biplane, who achieved the success of the morning by rounding the
course--a distance of six and a quarter miles--in nine minutes with a
twenty mile an hour wind blowing. His flight finished the morning.

Wind and rain kept competitors out of the air until the evening, when
Latham went up, to be followed almost immediately by the Comte de
Lambert. Sommer, Cockburn (the only English competitor), Delagrange,
Fournier, Lefebvre, Bleriot, Bunau-Varilla, Tissandier, Paulhan,
and Ferber turned out after the first two, and the excitement of the
spectators at seeing so many machines in the air at one time provoked
wild cheering. The only accident of the day came when Bleriot damaged
his propeller in colliding with a haycock.

The main results of the day were that the Comte de Lambert flew 30
kilometres in 29 minutes 2 seconds; Lefebvre made the ten-kilometre
circle of the track in just a second under 9 minutes, while Tissandier
did it in 9 1/4 minutes, and Paulhan reached a height of 230 feet. Small
as these results seem to us now, and ridiculous as may seem enthusiasm
at the sight of a few machines in the air at the same time, the Rheims
Meeting remains a great event, since it proved definitely to the whole
world that the conquest of the air had been achieved.

Throughout the week record after record was made and broken. Thus on
the Monday, Lefebvre put up a record for rounding the course and Bleriot
beat it, to be beaten in turn by Glenn Curtiss on his Curtiss-Herring
biplane. On that day, too, Paulhan covered 34 3/4 miles in 1 hour 6
minutes. On the next day, Paulhan on his Voisin biplane took the air
with Latham, and Fournier followed, only to smash up his machine by
striking an eddy of wind which turned him over several times. On the
Thursday, one of the chief events was Latham's 43 miles accomplished in
1 hour 2 minutes in the morning and his 96.5 miles in 2 hours 13 minutes
in the afternoon, the latter flight only terminated by running out of
petrol. On the Friday, the Colonel Renard French airship, which had
flown over the ground under the pilotage of M. Kapfarer, paid Rheims a
second visit; Latham manoeuvred round the airship on his Antoinette and
finally left it far behind. Henry Farman won the Grand Prix de Champagne
on this day, covering 112 miles in 3 hours, 4 minutes, 56 seconds,
Latham being second with his 96.5 miles flight, and Paulhan third.

On the Saturday, Glenn Curtiss came to his own, winning the
Gordon-Bennett Cup by covering 20 kilometres in 15 minutes 50.6 seconds.
Bleriot made a good second with 15 minutes 56.2 seconds as his time,
and Latham and Lefebvre were third and fourth. Farman carried off the
passenger prize by carrying two passengers a distance of 6 miles in 10
minutes 39 seconds. On the last day Delagrange narrowly escaped serious
accident through the bursting of his propeller while in the air, Curtiss
made a new speed record by travelling at the rate of over 50 miles an
hour, and Latham, rising to 500 feet, won the altitude prize.

These are the cold statistics of the meeting; at this length of time it
is difficult to convey any idea of the enthusiasm of the crowds over
the achievements of the various competitors, while the incidents of
the week, comic and otherwise, are nearly forgotten now even by those
present in this making of history. Latham's great flight on the Thursday
was rendered a breathless episode by a downpour of rain when he had
covered all but a kilometre of the record distance previously achieved
by Paulhan, and there was wild enthusiasm when Latham flew on through
the rain until he had put up a new record and his petrol had run out.
Again, on the Friday afternoon, the Colonel Renard took the air together
with a little French dirigible, Zodiac III; Latham was already in the
air directly over Farman, who was also flying, and three crows which
turned out as rivals to the human aviators received as much cheering for
their appearance as had been accorded to the machines, which doubtless
they could not understand. Frightened by the cheering, the crows tried
to escape from the course, but as they came near the stands, the crowd
rose to cheer again and the crows wheeled away to make a second charge
towards safety, with the same result; the crowd rose and cheered at them
a third and fourth time; between ten and fifteen thousand people stood
on chairs and tables and waved hats and handkerchiefs at three ordinary,
everyday crows. One thoughtful spectator, having thoroughly enjoyed the
funny side of the incident, remarked that the ultimate mastery of the
air lies with the machine that comes nearest to natural flight. This
still remains for the future to settle.

Farman's world record, which won the Grand Prix de Champagne, was done
with a Gnome Rotary Motor which had only been run on the test bench
and was fitted to his machine four hours before he started on the great
flight. His propeller had never been tested, having only been completed
the night before. The closing laps of that flight, extending as they did
into the growing of the dusk, made a breathlessly eerie experience for
such of the spectators as stayed on to watch--and these were many. Night
came on steadily and Farman covered lap after lap just as steadily, a
buzzing, circling mechanism with something relentless in its isolated
persistency.

The final day of the meeting provided a further record in the quarter
million spectators who turned up to witness the close of the great week.
Bleriot, turning out in the morning, made a landing in some such fashion
as flooded the carburettor and caused it to catch fire. Bleriot himself
was badly burned, since the petrol tank burst and, in the end, only
the metal parts of the machine were left. Glenn Curtis tried to beat
Bleriot's time for a lap of the course, but failed. In the evening,
Farman and Latham went out and up in great circles, Farman cleaving his
way upward in what at the time counted for a huge machine, on circles
of about a mile diameter. His first round took him level with the top of
the stands, and, in his second, he circled the captive balloon anchored
in the middle of the grounds. After another circle, he came down on a
long glide, when Latham's lean Antoinette monoplane went up in circles
more graceful than those of Farman. 'Swiftly it rose and swept round
close to the balloon, veered round to the hangars, and out over to the
Rheims road. Back it came high over the stands, the people craning their
necks as the shrill cry of the engine drew nearer and nearer behind the
stands. Then of a sudden, the little form appeared away up in the deep
twilight blue vault of the sky, heading straight as an arrow for the
anchored balloon. Over it, and high, high above it went the Antoinette,
seemingly higher by many feet than the Farman machine. Then, wheeling
in a long sweep to the left, Latham steered his machine round past the
stands, where the people, their nerve-tension released on seeing the
machine descending from its perilous height of 500 feet, shouted their
frenzied acclamations to the hero of the meeting.

'For certainly "Le Tham," as the French call him, was the popular hero.
He always flew high, he always flew well, and his machine was a joy to
the eye, either afar off or at close quarters. The public feeling for
Bleriot is different. Bleriot, in the popular estimation, is the man who
fights against odds, who meets the adverse fates calmly and with good
courage, and to whom good luck comes once in a while as a reward for
much labour and anguish, bodily and mental. Latham is the darling of
the Gods, to whom Fate has only been unkind in the matter of the Channel
flight, and only then because the honour belonged to Bleriot.

'Next to these two, the public loved most Lefebvre, the joyous, the
gymnastic. Lefebvre was the comedian of the meeting. When things began
to flag, the gay little Lefebvre would trot out to his starting rail,
out at the back of the judge's enclosure opposite the stands, and after
a little twisting of propellers his Wright machine would bounce off the
end of its starting rail and proceed to do the most marvellous tricks
for the benefit of the crowd, wheeling to right and left, darting up and
down, now flying over a troop of the cavalry who kept the plain clear of
people and sending their horses into hysterics, anon making straight
for an unfortunate photographer who would throw himself and his precious
camera flat on the ground to escape annihilation as Lefebvre swept over
him 6 or 7 feet off the ground. Lefebvre was great fun, and when he had
once found that his machine was not fast enough to compete for speed
with the Bleriots, Antoinettes, and Curtiss, he kept to his metier of
amusing people. The promoters of the meeting owe Lefebvre a debt of
gratitude, for he provided just the necessary comic relief.'--(The Aero,
September 7th, 1909.)

It may be noted, in connection with the fact that Cockburn was the only
English competitor at the meeting, that the Rheims Meeting did more than
anything which had preceded it to waken British interest in aviation.
Previously, heavier-than-air flight in England had been regarded as
a freak business by the great majority, and the very few pioneers who
persevered toward winning England a share in the conquest of the air
came in for as much derision as acclamation. Rheims altered this; it
taught the world in general, and England in particular, that a serious
rival to the dirigible balloon had come to being, and it awakened the
thinking portion of the British public to the fact that the aeroplane
had a future.

The success of this great meeting brought about a host of imitations
of which only a few deserve bare mention since, unlike the first, they
taught nothing and achieved little. There was the meeting at Boulogne
late in September of 1909, of which the only noteworthy event was
Ferber's death. There was a meeting at Brescia where Curtiss again took
first prize for speed and Rougier put up a world's height record of 645
feet. The Blackpool meeting followed between 18th and 23rd of October,
1909, forming, with the exception of Doncaster, the first British Flying
Meeting. Chief among the competitors were Henry Farman, who took the
distance prize, Rougier, Paulhan, and Latham, who, by a flight in a high
wind, convinced the British public that the theory that flying was only
possible in a calm was a fallacy. A meeting at Doncaster was practically
simultaneous with the Blackpool week; Delagrange, Le Blon, Sommer, and
Cody were the principal figures in this event. It should be added
that 130 miles was recorded as the total flown at Doncaster, while at
Blackpool only 115 miles were flown. Then there were Juvisy, the first
Parisian meeting, Wolverhampton, and the Comte de Lambert's flight round
the Eiffel Tower at a height estimated at between 1,200 and 1,300 feet.
This may be included in the record of these aerial theatricals, since it
was nothing more.

Probably wakened to realisation of the possibilities of the aeroplane by
the Rheims Meeting, Germany turned out its first plane late in 1909.
It was known as the Grade monoplane, and was a blend of the Bleriot and
Santos-Dumont machines, with a tail suggestive of the Antoinette type.
The main frame took the form of a single steel tube, at the forward end
of which was rigged a triangular arrangement carrying the pilot's seat
and the landing wheels underneath, with the wing warping wires and stays
above. The sweep of the wings was rather similar to the later Taube
design, though the sweep back was not so pronounced, and the machine was
driven by a four-cylinder, 20 horse-power, air-cooled engine which drove
a two-bladed tractor propeller. In spite of Lilienthal's pioneer
work years before, this was the first power-driven German plane which
actually flew.

Eleven months after the Rheims meeting came what may be reckoned the
only really notable aviation meeting on English soil, in the form of the
Bournemouth week, July 10th to 16th, 1910. This gathering is noteworthy
mainly in view of the amazing advance which it registered on the Rheims
performances. Thus, in the matter of altitude, Morane reached 4,107
feet and Drexel came second with 2,490 feet. Audemars on a Demoiselle
monoplane made a flight of 17 miles 1,480 yards in 27 minutes 17.2
seconds, a great flight for the little Demoiselle. Morane achieved a
speed of 56.64 miles per hour, and Grahame White climbed to 1,000 feet
altitude in 6 minutes 36.8 seconds. Machines carrying the Gnome engine
as power unit took the great bulk of the prizes, and British-built
engines were far behind.

The Bournemouth Meeting will always be remembered with regret for the
tragedy of C. S. Rolls's death, which took place on the Tuesday, the
second day of the meeting. The first competition of the day was that
for the landing prize; Grahame White, Audemars, and Captain Dickson had
landed with varying luck, and Rolls, following on a Wright machine with
a tail-plane which ought never to have been fitted and was not part of
the Wright design, came down wind after a left-hand turn and turned left
again over the top of the stands in order to land up wind. He began to
dive when just clear of the stands, and had dropped to a height of 40
feet when he came over the heads of the people against the barriers.
Finding his descent too steep, he pulled back his elevator lever to
bring the nose of the machine up, tipping down the front end of the tail
to present an almost flat surface to the wind. Had all gone well, the
nose of the machine would have been forced up, but the strain on the
tail and its four light supports was too great; the tail collapsed, the
wind pressed down the biplane elevator, and the machine dived vertically
for the remaining 20 feet of the descent, hitting the ground vertically
and crumpling up. Major Kennedy, first to reach the debris, found Rolls
lying with his head doubled under him on the overturned upper main
plane; the lower plane had been flung some few feet away with the engine
and tanks under it. Rolls was instantaneously killed by concussion of
the brain.

Antithesis to the tragedy was Audemars on his Demoiselle, which was
named 'The Infuriated Grasshopper.' Concerning this, it was recorded
at the time that 'Nothing so excruciatingly funny as the action of
this machine has ever been seen at any aviation ground. The little
two-cylinder engine pops away with a sound like the frantic drawing of
ginger beer corks; the machine scutters along the ground with its tail
well up; then down comes the tail suddenly and seems to slap the ground
while the front jumps up, and all the spectators rock with laughter. The
whole attitude and the jerky action of the machine suggest a grasshopper
in a furious rage, and the impression is intensified when it comes down,
as it did twice on Wednesday, in long grass, burying its head in the
ground in its temper.'--(The Aero, July, 1910.)

The Lanark Meeting followed in August of the same year, and with the
bare mention of this, the subject of flying meetings may he left
alone, since they became mere matters of show until there came military
competitions such as the Berlin Meeting at the end of August, 1910,
and the British War office Trials on Salisbury Plain, when Cody won his
greatest triumphs. The Berlin meeting proved that, from the time of the
construction of the first successful German machine mentioned above, to
the date of the meeting, a good number of German aviators had qualified
for flight, but principally on Wright and Antoinette machines, though
by that time the Aviatik and Dorner German makes had taken the air. The
British War office Trials deserve separate and longer mention.

In 1910 in spite of official discouragement, Captain Dickson proved the
value of the aeroplane for scouting purposes by observing movements
of troops during the Military Manoeuvres on Salisbury Plain. Lieut.
Lancelot Gibbs and Robert Loraine, the actor-aviator, also made flights
over the manoeuvre area, locating troops and in a way anticipating the
formation and work of the Royal Flying Corps by a usefulness which could
not be officially recognised.




XV. THE CHANNEL CROSSING

It may be said that Louis Bleriot was responsible for the second great
landmark in the history of successful flight. The day when the brothers
Wright succeeded in accomplishing power-driven flight ranks as the first
of these landmarks. Ader may or may not have left the ground, but the
wreckage of his 'Avion' at the end of his experiment places his doubtful
success in a different category from that of the brothers Wright and
leaves them the first definite conquerors, just as Bleriot ranks as
first definite conqueror of the English Channel by air.

In a way, Louis Bleriot ranks before Farman in point of time; his
first flapping-wing model was built as early as 1900, and Voisin flew a
biplane glider of his on the Seine in the very early experimental days.
Bleriot's first four machines were biplanes, and his fifth, a monoplane,
was wrecked almost immediately after its construction. Bleriot had
studied Langley's work to a certain extent, and his sixth construction
was a double monoplane based on the Langley principle. A month after
he had wrecked this without damaging himself--for Bleriot had as many
miraculous escapes as any of the other fliers-he brought out number
seven, a fairly average monoplane. It was in December of 1907 after a
series of flights that he wrecked this machine, and on its successor, in
July of 1908, he made a flight of over 8 minutes. Sundry flights, more
or less successful, including the first cross-country flight from Toury
to Artenay, kept him busy up to the beginning of November, 1908, when
the wreckage in a fog of the machine he was flying sent him to the
building of 'number eleven,' the famous cross-channel aeroplane.

Number eleven was shown at the French Aero Show in the Grand Palais
and was given its first trials on the 18th January, 1909. It was first
fitted with a R.E.P. motor and had a lifting area of 120 square feet,
which was later increased to 150 square feet. The framework was of oak
and poplar spliced and reinforced with piano wire; the weight of the
machine was 47 lbs. and the undercarriage weight a further 60 lbs., this
consisting of rubber cord shock absorbers mounted on two wheels. The
R.E.P. motor was found unsatisfactory, and a three-cylinder Anzani
of 105 mm. bore and 120 mm. stroke replaced it. An accident seriously
damaged the machine on June 2nd, but Bleriot repaired it and tested it
at Issy, where between June 19th and June 23rd he accomplished flights
of 8, 12, 15, 16, and 36 minutes. On July 4th he made a 50-minute flight
and on the 13th flew from Etampes to Chevilly.

A few further details of construction may be given: the wings themselves
and an elevator at the tail controlled the rate of ascent and descent,
while a rudder was also fitted at the tail. The steering lever,
working on a universally jointed shaft--forerunner of the modern
joystick--controlled both the rudder and the wings, while a pedal
actuated the elevator. The engine drove a two-bladed tractor screw of 6
feet 7 inches diameter, and the angle of incidence of the wings was 20
degrees. Timed at Issy, the speed of the machine was given as 36 miles
an hour, and as Bleriot accomplished the Channel flight of 20 miles in
37 minutes, he probably had a slight following wind.

The Daily Mail had offered a prize of L1,000 for the first Cross-Channel
flight, and Hubert Latham set his mind on winning it. He put up a
shelter on the French coast at Sangatte, half-way between Calais and
Cape Blanc Nez. From here he made his first attempt to fly to England
on Monday the 19th of July. He soared to a fair height, circling, and
reached an estimated height of about 900 feet as he came over the water
with every appearance of capturing the Cross-Channel prize. The luck
which dogged his career throughout was against him, for, after he had
covered some 8 miles, his engine stopped and he came down to the water
in a series of long glides. It was discovered afterward that a small
piece of wire had worked its way into a vital part of the engine to rob
Latham of the honour he coveted. The tug that came to his rescue found
him seated on the fuselage of his Antoinette, smoking a cigarette and
waiting for a boat to take him to the tug. It may be remarked that
Latham merely assumed his Antoinette would float in case he failed to
make the English coast; he had no actual proof.

Bleriot immediately entered his machine for the prize and took up his
quarters at Barraques. On Sunday, July 25th, 1909, shortly after 4 a.m.,
Bleriot had his machine taken out from its shelter and prepared for
flight. He had been recently injured in a petrol explosion and hobbled
out on crutches to make his cross-Channel attempt; he made two great
circles in the air to try the machine, and then alighted. 'In ten
minutes I start for England,' he declared, and at 4.35 the motor was
started up. After a run of 100 yards, the machine rose in the air and
got a height of about 100 feet over the land, then wheeling sharply
seaward and heading for Dover.

Bleriot had no means of telling direction, and any change of wind might
have driven him out over the North Sea, to be lost, as were Cecil Grace
and Hamel later on. Luck was with him, however, and at 5.12 a.m. of that
July Sunday, he made his landing in the North Fall meadow, just behind
Dover Castle. Twenty minutes out from the French coast, he lost sight of
the destroyer which was patrolling the Channel, and at the same time
he was out of sight of land without compass or any other means of
ascertaining his direction. Sighting the English coast, he found that
he had gone too far to the east, for the wind increased in strength
throughout the flight, this to such an extent as almost to turn the
machine round when he came over English soil. Profiting by Latham's
experience, Bleriot had fitted an inflated rubber cylinder a foot in
diameter by 5 feet in length along the middle of his fuselage, to render
floating a certainty in case he had to alight on the water.

Latham in his camp at Sangatte had been allowed to sleep through the
calm of the early morning through a mistake on the part of a friend, and
when his machine was turned out--in order that he might emulate Bleriot,
although he no longer hoped to make the first flight, it took so long
to get the machine ready and dragged up to its starting-point that there
was a 25 mile an hour wind by the time everything was in readiness.
Latham was anxious to make the start in spite of the wind, but the
Directors of the Antoinette Company refused permission. It was not until
two days later that the weather again became favourable, and then with a
fresh machine, since the one on which he made his first attempt had
been very badly damaged in being towed ashore, he made a circular trial
flight of about 5 miles. In landing from this, a side gust of wind drove
the nose of the machine against a small hillock, damaging both propeller
blades and chassis, and it was not until evening that the damage was
repaired.

French torpedo boats were set to mark the route, and Latham set out on
his second attempt at six o'clock. Flying at a height of 200 feet, he
headed over the torpedo boats for Dover and seemed certain of making the
English coast, but a mile and a half out from Dover his engine failed
him again, and he dropped to the water to be picked up by the steam
pinnace of an English warship and put aboard the French destroyer
Escopette.

There is little to choose between the two aviators for courage in
attempting what would have been considered a foolhardy feat a year or
two before. Bleriot's state, with an abscess in the burnt foot which had
to control the elevator of his machine, renders his success all the
more remarkable. His machine was exhibited in London for a time, and
was afterwards placed in the Conservatoire des Arts et Metiers, while a
memorial in stone, copying his monoplane in form, was let into the turf
at the point where he landed.

The second Channel crossing was not made until 1910, a year of new
records. The altitude record had been lifted to over 10,000 feet, the
duration record to 8 hours 12 minutes, and the distance for a single
flight to 365 miles, while a speed of over 65 miles an hour had been
achieved, when Jacques de Lesseps, son of the famous engineer of Suez
Canal and Panama fame, crossed from France to England on a Bleriot
monoplane. By this time flying had dropped so far from the marvellous
that this second conquest of the Channel aroused but slight public
interest in comparison with Bleriot's feat.

The total weight of Bleriot's machine in Cross Channel trim was 660
lbs., including the pilot and sufficient petrol for a three hours' run;
at a speed of 37 miles an hour, it was capable of carrying about 5
lbs. per square foot of lifting surface. It was the three-cylinder 25
horse-power Anzani motor which drove the machine for the flight. Shortly
after the flight had been accomplished, it was announced that the
Bleriot firm would construct similar machines for sale at L400 apiece--a
good commentary on the prices of those days.

On June the 2nd, 1910, the third Channel crossing was made by C. S.
Rolls, who flew from Dover, got himself officially observed over French
soil at Barraques, and then flew back without landing. He was the first
to cross from the British side of the Channel and also was the first
aviator who made the double journey. By that time, however, distance
flights had so far increased as to reduce the value of the feat, and
thenceforth the Channel crossing was no exceptional matter. The honour,
second only to that of the Wright Brothers, remains with Bleriot.




XVI. LONDON TO MANCHESTER

The last of the great contests to arouse public enthusiasm was the
London to Manchester Flight of 1910. As far back as 1906, the Daily
Mail had offered a prize of L10,000 to the first aviator who should
accomplish this journey, and, for a long time, the offer was regarded as
a perfectly safe one for any person or paper to make--it brought forth
far more ridicule than belief. Punch offered a similar sum to the first
man who should swim the Atlantic and also for the first flight to Mars
and back within a week, but in the spring of 1910 Claude Grahame White
and Paulhan, the famous French pilot, entered for the 183 mile run on
which the prize depended. Both these competitors flew the Farman biplane
with the 50 horse-power Gnome motor as propulsive power. Grahame White
surveyed the ground along the route, and the L. & N. W. Railway Company,
at his request, whitewashed the sleepers for 100 yards on the north side
of all junctions to give him his direction on the course. The machine
was run out on to the starting ground at Park Royal and set going at
5.19 a.m. on April 23rd. After a run of 100 yards, the machine went up
over Wormwood Scrubs on its journey to Normandy, near Hillmorten, which
was the first arranged stopping place en route; Grahame White landed
here in good trim at 7.20 a.m., having covered 75 miles and made a
world's record cross country flight. At 8.15 he set off again to come
down at Whittington, four miles short of Lichfield, at about 9.20, with
his machine in good order except for a cracked landing skid. Twice, on
this second stage of the journey, he had been caught by gusts of wind
which turned the machine fully round toward London, and, when over a
wood near Tamworth, the engine stopped through a defect in the balance
springs of two exhaust valves; although it started up again after a 100
foot glide, it did not give enough power to give him safety in the gale
he was facing. The rising wind kept him on the ground throughout the
day, and, though he hoped for better weather, the gale kept up until
the Sunday evening. The men in charge of the machine during its halt had
attempted to hold the machine down instead of anchoring it with stakes
and ropes, and, in consequence of this, the wind blew the machine over
on its back, breaking the upper planes and the tail. Grahame White had
to return to London, while the damaged machine was prepared for a second
flight. The conditions of the competition enacted that the full journey
should be completed within 24 hours, which made return to the starting
ground inevitable.

Louis Paulhan, who had just arrived with his Farman machine, immediately
got it unpacked and put together in order to be ready to make his
attempt for the prize as soon as the weather conditions should admit.
At 5.31 p.m., on April 27th, he went up from Hendon and had travelled
50 miles when Grahame White, informed of his rival's start, set out to
overtake him. Before nightfall Paulhan landed at Lichfield, 117 miles
from London, while Grahame White had to come down at Roden, only 60
miles out. The English aviator's chance was not so small as it seemed,
for, as Latham had found in his cross-Channel attempts, engine failure
was more the rule than the exception, and a very little thing might
reverse the relative positions.

A special train accompanied Paulhan along the North-Western route,
conveying Madame Paulhan, Henry Farman, and the mechanics who fitted the
Farman biplane together. Paulhan himself, who had flown at a height of
1,000 feet, spent the night at Lichfield, starting again at 4.9 a.m.
On the 28th, passing Stafford at 4.45, Crewe at 5.20, and landing at
Burnage, near Didsbury, at 5.32, having had a clean run.

Meanwhile, Grahame White had made a most heroic attempt to beat his
rival. An hour before dawn on the 28th, he went to the small field in
which his machine had landed, and in the darkness managed to make an
ascent from ground which made starting difficult even in daylight.
Purely by instinct and his recollection of the aspect of things the
night before, he had to clear telegraph wires and a railway bridge,
neither of which he could possibly see at that hour. His engine, too,
was faltering, and it was obvious to those who witnessed his start that
its note was far from perfect.

At 3.50 he was over Nuneaton and making good progress; between
Atherstone and Lichfield the wind caught him and the engine failed more
and more, until at 4.13 in the morning he was forced to come to earth,
having covered 6 miles less distance than in his first attempt. It was
purely a case of engine failure, for, with full power, he would have
passed over Paulhan just as the latter was preparing for the restart.
Taking into consideration the two machines, there is little doubt that
Grahame White showed the greater flying skill, although he lost the
prize. After landing and hearing of Paulhan's victory, on which he wired
congratulations, he made up his mind to fly to Manchester within the
24 hours. He started at 5 o'clock in the afternoon from Polesworth, his
landing place, but was forced to land at 5.30 at Whittington, where
he had landed on the previous Saturday. The wind, which had forced his
descent, fell again and permitted of starting once more; on this third
stage he reached Lichfield, only to make his final landing at 7.15 p.m.,
near the Trent Valley station. The defective running of the Gnome engine
prevented his completing the course, and his Farman machine had to be
brought back to London by rail.

The presentation of the prize to Paulhan was made the occasion for the
announcement of a further competition, consisting of a 1,000 mile flight
round a part of Great Britain. In this, nineteen competitors started,
and only four finished; the end of the race was a great fight between
Beaumont and Vedrines, both of whom scorned weather conditions in their
determination to win. Beaumont made the distance in a flying time of
22 hours 28 minutes 19 seconds, and Vedrines covered the journey in
a little over 23 1/2 hours. Valentine came third on a Deperdussin
monoplane and S. F. Cody on his Cathedral biplane was fourth. This was
in 1911, and by that time heavier-than-air flight had so far advanced
that some pilots had had war experience in the Italian campaign in
Tripoli, while long cross-country flights were an everyday event, and
bad weather no longer counted.




XVII. A SUMMARY, TO 1911

There is so much overlapping in the crowded story of the first years
of successful power-driven flight that at this point it is advisable to
make a concise chronological survey of the chief events of the period of
early development, although much of this is of necessity recapitulation.
The story begins, of course, with Orville Wright's first flight of 852
feet at Kitty Hawk on December 19th, 1903. The next event of note was
Wright's flight of 11.12 miles in 18 minutes 9 seconds at Dayton,
Ohio, on September 26th, 1905, this being the first officially recorded
flight. On October 4th of the same year, Wright flew 20.75 miles in 33
minutes 17 seconds, this being the first flight of over 20 miles ever
made. Then on September 14th 1906, Alberto Santos-Dumont made a
flight of eight seconds on the second heavier-than-air machine he had
constructed. It was a big box-kite-like machine; this was the second
power-driven aeroplane in Europe to fly, for although Santos-Dumont's
first machine produced in 1905 was reckoned an unsuccessful design, it
had actually got off the ground for brief periods. Louis Bleriot came
into the ring on April 5th, 1907, with a first flight of 6 seconds on a
Bleriot monoplane, his eighth but first successful construction.

Henry Farman made his first appearance in the history of aviation with a
flight of 935 feet on a Voisin biplane on October 15th 1907. On October
25th, in a flight of 2,530 feet, he made the first recorded turn in
the air, and on March 29th, 1908, carrying Leon Delagrange on a Voisin
biplane, he made the first passenger flight. On April 10th of this
year, Delagrange, in flying 1 1/2 miles, made the first flight in Europe
exceeding a mile in distance. He improved on this by flying 10 1/2 miles
at Milan on June 22nd, while on July 8th, at Turin, he took up Madame
Peltier, the first woman to make an aeroplane flight.

Wilbur Wright, coming over to Europe, made his first appearance on the
Continent with a flight of 1 3/4 minutes at Hunaudieres, France, on
August 8th, 1908. On September 6th, at Chalons, he flew for 1 hour 4
minutes 26 seconds with a passenger, this being the first flight in
which an hour in the air was exceeded with a passenger on board.

On September 12th 1908, Orville Wright, flying at Fort Meyer, U.S.A.,
with Lieut. Selfridge as passenger, crashed his machine, suffering
severe injuries, while Selfridge was killed. This was the first
aeroplane fatality. On October 30th, 1908, Farman made the first
cross-country flight, covering the distance of 17 miles between Bouy and
Rheims. The next day, Louis Bleriot, in flying from Toury to Artenay,
made two landings en route, this being the first cross-country flight
with landings. On the last day of the year, Wilbur Wright won the
Michelin Cup at Auvours with a flight of 90 miles, which, lasting 2
hours 20 minutes 23 seconds, exceeded 2 hours in the air for the first
time.

On January 2nd, 1909, S. F. Cody opened the New Year by making the first
observed flight at Farnborough on a British Army aeroplane. It was not
until July 18th of 1909 that the first European height record deserving
of mention was put up by Paulhan, who achieved a height of 450 feet on a
Voisin biplane. This preceded Latham's first attempt to fly the Channel
by two days, and five days later, on the 25th of the month, Bleriot made
the first Channel crossing. The Rheims Meeting followed on August 22nd,
and it was a great day for aviation when nine machines were seen in
the air at once. It was here that Farman, with a 118 mile flight,
first exceeded the hundred miles, and Latham raised the height record
officially to 500 feet, though actually he claimed to have reached 1,200
feet. On September 8th, Cody, flying from Aldershot, made a 40 mile
journey, setting up a new cross-country record. On October 19th the
Comte de Lambert flew from Juvisy to Paris, rounded the Eiffel Tower and
flew back. J. T. C. Moore-Brabazon made the first circular mile flight
by a British aviator on an all-British machine in Great Britain, on
October 30th, flying a Short biplane with a Green engine. Paulhan,
flying at Brooklands on November 2nd, accomplished 96 miles in 2 hours
48 minutes, creating a British distance record; on the following
day, Henry Farman made a flight of 150 miles in 4 hours 22 minutes
at Mourmelon, and on the 5th of the month, Paulhan, flying a Farman
biplane, made a world's height record of 977 feet. This, however, was
not to stand long, for Latham got up to 1,560 feet on an Antoinette at
Mourmelon on December 1st. December 31st witnessed the first flight
in Ireland, made by H. Ferguson on a monoplane which he himself had
constructed at Downshire Park, Lisburn.

These, thus briefly summarised, are the principal events up to the end
of 1909. 1910 opened with tragedy, for on January 4th Leon Delagrange,
one of the greatest pilots of his time, was killed while flying at
Pau. The machine was the Bleriot XI which Delagrange had used at the
Doncaster meeting, and to which Delagrange had fitted a 50 horse-power
Gnome engine, increasing the speed of the machine from its original
30 to 45 miles per hour. With the Rotary Gnome engine there was of
necessity a certain gyroscopic effect, the strain of which proved too
much for the machine. Delagrange had come to assist in the inauguration
of the Croix d'Hins aerodrome, and had twice lapped the course at a
height of about 60 feet. At the beginning of the third lap, the strain
of the Gnome engine became too great for the machine; one wing collapsed
as if the stay wires had broken, and the whole machine turned over and
fell, killing Delagrange.

On January 7th Latham, flying at Mourmelon, first made the vertical
kilometre and dedicated the record to Delagrange, this being the day of
his friend's funeral. The record was thoroughly authenticated by a large
registering barometer which Latham carried, certified by the officials
of the French Aero Club. Three days later Paulhan, who was at Los
Angeles, California, raised the height record to 4,146 feet.

On January 25th the Brussels Exhibition opened, when the Antoinette
monoplane, the Gaffaux and Hanriot monoplanes, together with the
d'Hespel aeroplane, were shown; there were also the dirigible Belgica
and a number of interesting aero engines, including a German airship
engine and a four-cylinder 50 horse-power Miesse, this last air-cooled
by means of 22 fans driving a current of air through air jackets
surrounding fluted cylinders.

On April 2nd Hubert Le Blon, flying a Bleriot with an Anzani engine,
was killed while flying over the water. His machine was flying quite
steadily, when it suddenly heeled over and came down sideways into the
sea; the motor continued running for some seconds and the whole machine
was drawn under water. When boats reached the spot, Le Blon was found
lying back in the driving seat floating just below the surface. He had
done good flying at Doncaster, and at Heliopolis had broken the world's
speed records for 5 and 10 kilometres. The accident was attributed to
fracture of one of the wing stay wires when running into a gust of wind.

The next notable event was Paulhan's London-Manchester flight, of which
full details have already been given. In May Captain Bertram Dickson,
flying at the Tours meeting, beat all the Continental fliers whom he
encountered, including Chavez, the Peruvian, who later made the
first crossing of the Alps. Dickson was the first British winner of
international aviation prizes.

C. S. Rolls, of whom full details have already been given, was killed at
Bournemouth on July 12th, being the first British aviator of note to be
killed in an aeroplane accident. His return trip across the Channel had
taken place on June 2nd. Chavez, who was rapidly leaping into fame, as
a pilot, raised the British height record to 5,750 feet while flying at
Blackpool on August 3rd. On the 11th of that month, Armstrong Drexel,
flying a Bleriot, made a world's height record of 6,745 feet.

It was in 1910 that the British War office first began fully to realise
that there might be military possibilities in heavier-than-air flying.
C. S. Rolls had placed a Wright biplane at the disposal of the military
authorities, and Cody, as already recorded, had been experimenting with
a biplane type of his own for some long period. Such development as was
achieved was mainly due to the enterprise and energy of Colonel J. E.
Capper, C.B., appointed to the superintendency of the Balloon Factory
and Balloon School at Farnborough in 1906. Colonel Capper's retirement
in 1910 brought (then) Mr Mervyn O'Gorman to command, and by that time
the series of successes of the Cody biplane, together with the proved
efficiency of the aeroplane in various civilian meetings, had convinced
the British military authorities that the mastery of the air did not lie
altogether with dirigible airships, and it may be said that in 1910 the
British War office first began seriously to consider the possibilities
of the aeroplane, though two years more were to elapse before the
formation of the Royal Flying Corps marked full realisation of its
value.

A triumph and a tragedy were combined in September of 1910. On the 23rd
of the month, Georges Chavez set out to fly across the Alps on a Bleriot
monoplane. Prizes had been offered by the Milan Aviation Committee for
a flight from Brigue in Switzerland over the Simplon Pass to Milan,
a distance of 94 miles with a minimum height of 6,600 feet above sea
level. Chavez started at 1.30 p.m. On the 23rd, and 41 minutes later he
reached Domodossola, 25 miles distant. Here he descended, numbed with
the cold of the journey; it was said that the wings of his machine
collapsed when about 30 feet from the ground, but however this may
have been, he smashed the machine on landing, and broke both legs, in
addition to sustaining other serious injuries. He lay in hospital until
the 27th September, when he died, having given his life to the conquest
of the Alps. His death in the moment of success was as great a tragedy
as were those of Pilcher and Lilienthal.

The day after Chavez's death, Maurice Tabuteau flew across the Pyrenees,
landing in the square at Biarritz. On December 30th, Tabuteau made a
flight of 365 miles in 7 hours 48 minutes. Farman, on December 18th, had
flown for over 8 hours, but his total distance was only 282 miles. The
autumn of this year was also noteworthy for the fact that aeroplanes
were first successfully used in the French Military Manoeuvres. The
British War Office, by the end of the year, had bought two machines, a
military type Farman and a Paulhan, ignoring British experimenters and
aeroplane builders of proved reliability. These machines, added to an
old Bleriot two-seater, appear to have constituted the British aeroplane
fleet of the period.

There were by this time three main centres of aviation in England, apart
from Cody, alone on Laffan's Plain. These three were Brooklands, Hendon,
and the Isle of Sheppey, and of the three Brooklands was chief.
Here such men as Graham Gilmour, Rippen, Leake, Wickham, and Thomas
persistently experimented. Hendon had its own little group, and
Shellbeach, Isle of Sheppey, held such giants of those days as C. S.
Rolls and Moore Brabazon, together with Cecil Grace and Rawlinson. One
or other, and sometimes all of these were deserted on the occasion of
some meeting or other, but they were the points where the spade work was
done, Brooklands taking chief place. 'If you want the early history
of flying in England, it is there,' one of the early school remarked,
pointing over toward Brooklands course.

1911 inaugurated a new series of records of varying character. On
the 17th January, E. B. Ely, an American, flew from the shore of San
Francisco to the U.S. cruiser Pennsylvania, landing on the cruiser,
and then flew back to the shore. The British military designing of
aeroplanes had been taken up at Farnborough by G. H. de Havilland, who
by the end of January was flying a machine of his own design, when he
narrowly escaped becoming a casualty through collision with an obstacle
on the ground, which swept the undercarriage from his machine.

A list of certified pilots of the countries of the world was issued
early in 1911, showing certificates granted up to the end of 1910.
France led the way easily with 353 pilots; England came next with 57,
and Germany next with 46; Italy owned 32, Belgium 27, America 26, and
Austria 19; Holland and Switzerland had 6 aviators apiece, while Denmark
followed with 3, Spain with 2, and Sweden with 1. The first certificate
in England was that of J. T. C. Moore-Brabazon, while Louis Bleriot was
first on the French list and Glenn Curtiss, first holder of an American
certificate, also held the second French brevet.

On the 7th March, Eugene Renaux won the Michelin Grand Prize by flying
from the French Aero Club ground at St Cloud and landing on the Puy de
Dome. The landing, which was one of the conditions of the prize, was
one of the most dangerous conditions ever attached to a competition;
it involved dropping on to a little plateau 150 yards square, with
a possibility of either smashing the machine against the face of the
mountain, or diving over the edge of the plateau into the gulf beneath.
The length of the journey was slightly over 200 miles and the height of
the landing point 1,465 metres, or roughly 4,500 feet above sea-level.
Renaux carried a passenger, Doctor Senoucque, a member of Charcot's
South Polar Expedition.

The 1911 Aero Exhibition held at Olympia bore witness to the enormous
strides made in construction, more especially by British designers,
between 1908 and the opening of the Show. The Bristol Firm showed three
machines, including a military biplane, and the first British built
biplane with tractor screw. The Cody biplane, with its enormous size
rendering it a prominent feature of the show, was exhibited. Its
designer anticipated later engines by expressing his desire for a motor
of 150 horse-power, which in his opinion was necessary to get the best
results from the machine. The then famous Dunne monoplane was exhibited
at this show, its planes being V-shaped in plan, with apex leading. It
embodied the results of very lengthy experiments carried out both with
gliders and power-driven machines by Colonel Capper, Lieut. Gibbs,
and Lieut. Dunne, and constituted the longest step so far taken in the
direction of inherent stability.

Such forerunners of the notable planes of the war period as the Martin
Handasyde, the Nieuport, Sopwith, Bristol, and Farman machines, were
features of the show; the Handley-Page monoplane, with a span of 32
feet over all, a length of 22 feet, and a weight of 422 lbs., bore no
relation at all to the twin-engined giant which later made this firm
famous. In the matter of engines, the principal survivals to the present
day, of which this show held specimens, were the Gnome, Green, Renault
air-cooled, Mercedes four-cylinder dirigible engine of 115 horse-power,
and 120 horsepower Wolseley of eight cylinders for use with dirigibles.

On April 12th, of 1911, Paprier, instructor at the Bleriot school at
Hendon, made the first non-stop flight between London and Paris. He left
the aerodrome at 1.37 p.m., and arrived at Issy-les-Moulineaux at 5.33
p.m., thus travelling 250 miles in a little under 4 hours. He followed
the railway route practically throughout, crossing from Dover to nearly
opposite Calais, keeping along the coast to Boulogne, and then following
the Nord Railway to Amiens, Beauvais, and finally Paris.

In May, the Paris-Madrid race took place; Vedrines, flying a Morane
biplane, carried off the prize by first completing the distance of 732
miles. The Paris-Rome race of 916 miles was won in the same month by
Beaumont, flying a Bleriot monoplane. In July, Koenig won the German
National Circuit race of 1,168 miles on an Albatross biplane. This was
practically simultaneous with the Circuit of Britain won by Beaumont,
who covered 1,010 miles on a Bleriot monoplane, having already won
the Paris-Brussels-London-Paris Circuit of 1,080 miles, this also on
a Bleriot. It was in August that a new world's height record of 11,152
feet was set up by Captain Felix at Etampes, while on the 7th of the
month Renaux flew nearly 600 miles on a Maurice Farman machine in 12
hours. Cody and Valentine were keeping interest alive in the Circuit of
Britain race, although this had long been won, by determinedly plodding
on at finishing the course.

On September 9th, the first aerial post was tried between Hendon and
Windsor, as an experiment in sending mails by aeroplane. Gustave Hamel
flew from Hendon to Windsor and back in a strong wind. A few days
later, Hamel went on strike, refusing to carry further mails unless the
promoters of the Aerial Postal Service agreed to pay compensation to
Hubert, who fractured both his legs on the 11th of the month while
engaged in aero postal work. The strike ended on September 25th, when
Hamel resumed mail-carrying in consequence of the capitulation of the
Postmaster-General, who agreed to set aside L500 as compensation to
Hubert.

September also witnessed the completion in America of a flight across
the Continent, a distance of 2,600 miles. The only competitor who
completed the full distance was C. P. Rogers, who was disqualified
through failing to comply with the time limit. Rogers needed so many
replacements to his machine on the journey that, expressing it in
American fashion, he arrived with practically a dfferent aeroplane from
that with which he started.

With regard to the aerial postal service, analysis of the matter carried
and the cost of the service seemed to show that with a special charge of
one shilling for letters and sixpence for post cards, the revenue just
balanced the expenditure. It was not possible to keep to the time-table
as, although the trials were made in the most favourable season of the
year, aviation was not sufficiently advanced to admit of facing all
weathers and complying with time-table regulations.

French military aeroplane trials took place at Rheims in October, the
noteworthy machines being Antoinette, Farman, Nieuport, and Deperdussin.
The tests showed the Nieuport monoplane with Gnome motor as first in
position; the Breguet biplane was second, and the Deperdussin monoplanes
third. The first five machines in order of merit were all engined with
the Gnome motor.

The records quoted for 1911 form the best evidence that can be given of
advance in design and performance during the year. It will be seen that
the days of the giants were over; design was becoming more and more
standardised and aviation not so much a matter of individual courage and
even daring, as of the reliability of the machine and its engine.
This was the first year in which the twin-engined aeroplane made its
appearance, and it was the year, too, in which flying may be said to
have grown so common that the 'meetings' which began with Rheims were
hardly worth holding, owing to the fact that increase in height and
distance flown rendered it no longer necessary for a would-be spectator
of a flight to pay half a crown and enter an enclosure. Henceforth,
flying as a spectacle was very little to be considered; its commercial
aspects were talked of, and to a very slight degree exploited, but, more
and more, the fact that the aeroplane was primarily an engine of war,
and the growing German menace against the peace of the world combined
to point the way of speediest development, and the arrangements for the
British Military Trials to be held in August, 1912, showed that even
the British War office was waking up to the potentialities of this new
engine of war.




XVIII. A SUMMARY, TO 1914

Consideration of the events in the years immediately preceding the War
must be limited to as brief a summary as possible, this not only because
the full history of flying achievements is beyond the compass of any
single book, but also because, viewing the matter in perspective, the
years 1903-1911 show up as far more important as regards both design and
performance. From 1912 to August of 1914, the development of aeronautics
was hindered by the fact that it had not progressed far enough to form
a real commercial asset in any country. The meetings which drew vast
concourses of people to such places as Rheims and Bournemouth may have
been financial successes at first, but, as flying grew more common and
distances and heights extended, a great many people found it other than
worth while to pay for admission to an aerodrome. The business of taking
up passengers for pleasure flights was not financially successful, and,
although schemes for commercial routes were talked of, the aeroplane was
not sufficiently advanced to warrant the investment of hard cash in
any of these projects. There was a deadlock; further development
was necessary in order to secure financial aid, and at the same time
financial aid was necessary in order to secure further development.
Consequently, neither was forthcoming.

This is viewing the matter in a broad and general sense; there were
firms, especially in France, but also in England and America, which
looked confidently for the great days of flying to arrive, and regarded
their sunk capital as investment which would eventually bring its due
return. But when one looks back on those years, the firms in question
stand out as exceptions to the general run of people, who regarded
aeronautics as something extremely scientific, exceedingly dangerous,
and very expensive. The very fame that was attained by such pilots as
became casualties conduced to the advertisement of every death, and the
dangers attendant on the use of heavier-than-air machines became greatly
exaggerated; considering the matter as one of number of miles flown,
even in the early days, flying exacted no more toll in human life than
did railways or road motors in the early stages of their development.
But to take one instance, when C. S. Rolls was killed at Bournemouth by
reason of a faulty tail-plane, the fact was shouted to the whole world
with almost as much vehemence as characterised the announcement of the
Titanic sinking in mid-Atlantic.

Even in 1911 the deadlock was apparent; meetings were falling off in
attendance, and consequently in financial benefit to the promoters;
there remained, however, the knowledge--for it was proved past
question--that the aeroplane in its then stage of development was a
necessity to every army of the world. France had shown this by the more
than interest taken by the French Government in what had developed into
an Air Section of the French army; Germany, of course, was hypnotised by
Count Zeppelin and his dirigibles, to say nothing of the Parsevals which
had been proved useful military accessories; in spite of this, it was
realised in Germany that the aeroplane also had its place in military
affairs. England came into the field with the military aeroplane trials
of August 1st to 15th, 1912, barely two months after the founding of the
Royal Flying Corps.

When the R.F.C. was founded--and in fact up to two years after its
founding--in no country were the full military potentialities of the
aeroplane realised; it was regarded as an accessory to cavalry for
scouting more than as an independent arm; the possibilities of bombing
were very vaguely considered, and the fact that it might be possible to
shoot from an aeroplane was hardly considered at all. The conditions of
the British Military Trials of 1912 gave to the War office the option
of purchasing for L1,000 any machine that might be awarded a prize.
Machines were required, among other things, to carry a useful load of
350 lbs. in addition to equipment, with fuel and oil for 4 1/2-hours;
thus loaded, they were required to fly for 3 hours, attaining an
altitude of 4,500 feet, maintaining a height of 1,500 feet for 1 hour,
and climbing 1,000 feet from the ground at a rate of 200 feet per
minute, 'although 300 feet per minute is desirable.' They had to attain
a speed of not less than 55 miles per hour in a calm, and be able to
plane down to the ground in a calm from not more than 1,000 feet with
engine stopped, traversing 6,000 feet horizontal distance. For those
days, the landing demands were rather exacting; the machine should be
able to rise without damage from long grass, clover, or harrowed land,
in 100 yards in a calm, and should be able to land without damage on any
cultivated ground, including rough ploughed land, and, when landing on
smooth turf in a calm, be able to pull up within 75 yards of the point
of first touching the ground. It was required that pilot and observer
should have as open a view as possible to front and flanks, and they
should be so shielded from the wind as to be able to communicate with
each other. These are the main provisions out of the set of conditions
laid down for competitors, but a considerable amount of leniency was
shown by the authorities in the competition, who obviously wished to try
out every machine entered and see what were its capabilities.

The beginning of the competition consisted in assembling the machines
against time from road trim to flying trim. Cody's machine, which was
the only one to be delivered by air, took 1 hour and 35 minutes to
assemble; the best assembling time was that of the Avro, which was got
into flying trim in 14 minutes 30 seconds. This machine came to grief
with Lieut. Parke as pilot, on the 7th, through landing at very high
speed on very bad ground; a securing wire of the under-carriage broke in
the landing, throwing the machine forward on to its nose and then over
on its back. Parke was uninjured, fortunately; the damaged machine was
sent off to Manchester for repair and was back again on the 16th of
August.

It is to be noted that by this time the Royal Aircraft Factory was
building aeroplanes of the B.E. and F.E. types, but at the same time it
is also to be noted that British military interest in engines was not
sufficient to bring them up to the high level attained by the planes,
and it is notorious that even the outbreak of war found England
incapable of providing a really satisfactory aero engine. In the 1912
Trials, the only machines which actually completed all their tests were
the Cody biplane, the French Deperdussin, the Hanriot, two Bleriots and
a Maurice Farman. The first prize of L4,000, open to all the world,
went to F. S. Cody's British-built biplane, which complied with all
the conditions of the competition and well earned its official
acknowledgment of supremacy. The machine climbed at 280 feet per minute
and reached a height of 5,000 feet, while in the landing test, in spite
of its great weight and bulk, it pulled up on grass in 56 yards. The
total weight was 2,690 lbs. when fully loaded, and the total area of
supporting surface was 500 square feet; the motive power was supplied
by a six-cylinder 120 horsepower Austro-Daimler engine. The second prize
was taken by A. Deperdussin for the French-built Deperdussin monoplane.
Cody carried off the only prize awarded for a British-built plane,
this being the sum of L1,000, and consolation prizes of L500 each were
awarded to the British Deperdussin Company and The British and Colonial
Aeroplane Company, this latter soon to become famous as makers of the
Bristol aeroplane, of which the war honours are still fresh in men's
minds.

While these trials were in progress Audemars accomplished the first
flight between Paris and Berlin, setting out from Issy early in the
morning of August 18th, landing at Rheims to refill his tanks within an
hour and a half, and then coming into bad weather which forced him
to land successively at Mezieres, Laroche, Bochum, and finally nearly
Gersenkirchen, where, owing to a leaky petrol tank, the attempt to win
the prize offered for the first flight between the two capitals had to
be abandoned after 300 miles had been covered, as the time limit was
definitely exceeded. Audemars determined to get through to Berlin, and
set off at 5 in the morning of the 19th, only to be brought down by fog;
starting off again at 9.15 he landed at Hanover, was off again at 1.35,
and reached the Johannisthal aerodrome in the suburbs of Berlin at 6.48
that evening.

As early as 1910 the British Government possessed some ten aeroplanes,
and in 1911 the force developed into the Army Air Battalion, with the
aeroplanes under the control of Major J. H. Fulton, R.F.A. Toward the
end of 1911 the Air Battalion was handed over to (then) Brig.-Gen. D.
Henderson, Director of Military Training. On June 6th, 1912, the Royal
Flying Corps was established with a military wing under Major F. H.
Sykes and a naval wing under Commander C. R. Samson. A joint Naval and
Military Flying School was established at Upavon with Captain Godfrey
M. Paine, R.N., as Commandant and Major Hugh Trenchard as Assistant
Commandant. The Royal Aircraft Factory brought out the B.E. and F.E.
types of biplane, admittedly superior to any other British design of the
period, and an Aircraft Inspection Department was formed under Major J.
H. Fulton. The military wing of the R.F.C. was equipped almost entirely
with machines of Royal Aircraft Factory design, but the Navy preferred
to develop British private enterprise by buying machines from private
firms. On July 1st, 1914 the establishment of the Royal Naval Air
Service marked the definite separation of the military and naval sides
of British aviation, but the Central Flying School at Upavon continued
to train pilots for both services.

It is difficult at this length of time, so far as the military wing was
concerned, to do full justice to the spade work done by Major-General
Sir David Henderson in the early days. Just before war broke out,
British military air strength consisted officially of eight squadrons,
each of 12 machines and 13 in reserve, with the necessary complement of
road transport. As a matter of fact, there were three complete squadrons
and a part of a fourth which constituted the force sent to France at the
outbreak of war. The value of General Henderson's work lies in the fact
that, in spite of official stinginess and meagre supplies of every kind,
he built up a skeleton organisation so elastic and so well thought out
that it conformed to war requirements as well as even the German plans
fitted in with their aerial needs. On the 4th of August, 1914, the
nominal British air strength of the military wing was 179 machines. Of
these, 82 machines proceeded to France, landing at Amiens and flying
to Maubeuge to play their part in the great retreat with the British
Expeditionary Force, in which they suffered heavy casualties both in
personnel and machines. The history of their exploits, however, belongs
to the War period.

The development of the aeroplane between 1912 and 1914 can be judged by
comparison of the requirements of the British War Office in 1912 with
those laid down in an official memorandum issued by the War Office
in February, 1914. This latter called for a light scout aeroplane, a
single-seater, with fuel capacity to admit of 300 miles range and a
speed range of from 50 to 85 miles per hour. It had to be able to climb
3,500 feet in five minutes, and the engine had to be so constructed that
the pilot could start it without assistance. At the same time, a heavier
type of machine for reconnaissance work was called for, carrying fuel
for a 200 mile flight with a speed range of between 35 and 60 miles per
hour, carrying both pilot and observer. It was to be equipped with
a wireless telegraphy set, and be capable of landing over a 30 foot
vertical obstacle and coming to rest within a hundred yards' distance
from the obstacle in a wind of not more than 15 miles per hour. A third
requirement was a heavy type of fighting aeroplane accommodating pilot
and gunner with machine gun and ammunition, having a speed range of
between 45 and 75 miles per hour and capable of climbing 3,500 feet in 8
minutes. It was required to carry fuel for a 300 mile flight and to give
the gunner a clear field of fire in every direction up to 30 degrees on
each side of the line of flight. Comparison of these specifications with
those of the 1912 trials will show that although fighting, scouting, and
reconnaissance types had been defined, the development of performance
compared with the marvellous development of the earlier years of
achieved flight was small.

Yet the records of those years show that here and there an outstanding
design was capable of great things. On the 9th September, 1912,
Vedrines, flying a Deperdussin monoplane at Chicago, attained a speed of
105 miles an hour. On August 12th, G. de Havilland took a passenger to a
height of 10,560 feet over Salisbury Plain, flying a B.E. biplane with
a 70 horse-power Renault engine. The work of de Havilland may be said to
have been the principal influence in British military aeroplane design,
and there is no doubt that his genius was in great measure responsible
for the excellence of the early B.E. and F.E. types.

On the 31st May, 1913, H. G. Hawker, flying at Brooklands, reached
a height of 11,450 feet on a Sopwith biplane engined with an 80
horse-power Gnome engine. On June 16th, with the same type of machine
and engine, he achieved 12,900 feet. On the 2nd October, in the same
year, a Grahame White biplane with 120 horse-power Austro-Daimler
engine, piloted by Louis Noel, made a flight of just under 20 minutes
carrying 9 passengers. In France a Nieuport monoplane piloted by G.
Legagneaux attained a height of 6,120 metres, or just over 20,070 feet,
this being the world's height record. It is worthy of note that of the
world's aviation records as passed by the International Aeronautical
Federation up to June 30th, 1914, only one, that of Noel, is credited to
Great Britain.

Just as records were made abroad, with one exception, so were the
really efficient engines. In England there was the Green engine, but the
outbreak of war found the Royal Flying Corps with 80 horse-power Gnomes,
70 horse-power Renaults, and one or two Antoinette motors, but not one
British, while the Royal Naval Air Service had got 20 machines with
engines of similar origin, mainly land planes in which the wheeled
undercarriages had been replaced by floats. France led in development,
and there is no doubt that at the outbreak of war, the French military
aeroplane service was the best in the world. It was mainly composed of
Maurice Farman two-seater biplanes and Bleriot monoplanes--the latter
type banned for a period on account of a number of serious accidents
that took place in 1912.

America had its Army Aviation School, and employed Burgess-Wright
and Curtiss machines for the most part. In the pre-war years, once
the Wright Brothers had accomplished their task, America's chief
accomplishment consisted in the development of the 'Flying Boat,'
alternatively named with characteristic American clumsiness, 'The
Hydro-Aeroplane.' In February of 1911, Glenn Curtiss attached a
float to a machine similar to that with which he won the first
Gordon-Bennett Air Contest and made his first flying boat
experiment. From this beginning he developed the boat form of body
which obviated the use and troubles of floats--his hydroplane became
its own float.

Mainly owing to greater engine reliability the duration records steadily
increased. By September of 1912 Fourny, on a Maurice Farman biplane, was
able to accomplish a distance of 628 miles without a landing, remaining
in the air for 13 hours 17 minutes and just over 57 seconds. By 1914
this was raised by the German aviator, Landemann, to 21 hours 48 3/4
seconds. The nature of this last record shows that the factors in such a
record had become mere engine endurance, fuel capacity, and capacity
of the pilot to withstand air conditions for a prolonged period, rather
than any exceptional flying skill.

Let these years be judged by the records they produced, and even then
they are rather dull. The glory of achievement such as characterised the
work of the Wright Brothers, of Bleriot, and of the giants of the early
days, had passed; the splendid courage, the patriotism and devotion
of the pilots of the War period had not yet come to being. There was
progress, past question, but it was mechanical, hardly ever inspired.
The study of climatic conditions was definitely begun and aeronautical
meteorology came to being, while another development already noted was
the fitting of wireless telegraphy to heavier-than-air machines, as
instanced in the British War office specification of February, 1914.
These, however, were inevitable; it remained for the War to force
development beyond the inevitable, producing in five years that which
under normal circumstances might easily have occupied fifty--the
aeroplane of to-day; for, as already remarked, there was a deadlock,
and any survey that may be made of the years 1912-1914, no matter how
superficial, must take it into account with a view to retaining correct
perspective in regard to the development of the aeroplane.

There is one story of 1914 that must be included, however briefly,
in any record of aeronautical achievement, since it demonstrates past
question that to Professor Langley really belongs the honour of having
achieved a design which would ensure actual flight, although the series
of accidents which attended his experiments gave to the Wright Brothers
the honour of first leaving the earth and descending without accident in
a power-driven heavier-than-air machine. In March, 1914, Glenn Curtiss
was invited to send a flying boat to Washington for the celebration
of 'Langley Day,' when he remarked, 'I would like to put the Langley
aeroplane itself in the air.' In consequence of this remark, Secretary
Walcot of the Smithsonian Institution authorised Curtiss to re-canvas
the original Langley aeroplane and launch it either under its own power
or with a more recent engine and propeller. Curtiss completed this, and
had the machine ready on the shores of Lake Keuka, Hammondsport, N.Y.,
by May. The main object of these renewed trials was to show whether the
original Langley machine was capable of sustained free flight with a
pilot, and a secondary object was to determine more fully the advantages
of the tandem monoplane type; thus the aeroplane was first flown
as nearly as possible in its original condition, and then with such
modifications as seemed desirable. The only difference made for the
first trials consisted in fitting floats with connecting trusses;
the steel main frame, wings, rudders, engine, and propellers were
substantially as they had been in 1903. The pilot had the same seat
under the main frame and the same general system of control. He could
raise or lower the craft by moving the rear rudder up and down; he could
steer right or left by moving the vertical rudder. He had no ailerons
nor wing-warping mechanism, but for lateral balance depended on the
dihedral angle of the wings and upon suitable movements of his weight or
of the vertical rudder.

After the adjustments for actual flight had been made in the Curtiss
factory, according to the minute descriptions contained in the Langley
Memoir on Mechanical Flight, the aeroplane was taken to the shore of
Lake Keuka, beside the Curtiss hangars, and assembled for launching. On
a clear morning (May 28th) and in a mild breeze, the craft was lifted
on to the water by a dozen men and set going, with Mr Curtiss at the
steering wheel, esconced in the little boat-shaped car under the forward
part of the frame. The four-winged craft, pointed somewhat across the
wind, went skimming over the waveless, then automatically headed into
the wind, rose in level poise, soared gracefully for 150 feet, and
landed softly on the water near the shore. Mr Curtiss asserted that he
could have flown farther, but, being unused to the machine, imagined
that the left wings had more resistance than the right. The truth is
that the aeroplane was perfectly balanced in wing resistance, but turned
on the water like a weather vane, owing to the lateral pressure on
its big rear rudder. Hence in future experiments this rudder was made
turnable about a vertical axis, as well as about the horizontal axis
used by Langley. Henceforth the little vertical rudder under the frame
was kept fixed and inactive.[*]

That the Langley aeroplane was subsequently fitted with an 80
horse-power Curtiss engine and successfully flown is of little interest
in such a record as this, except for the fact that with the weight
nearly doubled by the new engine and accessories the machine flew
successfully, and demonstrated the perfection of Langley's design by
standing the strain. The point that is of most importance is that the
design itself proved a success and fully vindicated Langley's work.
At the same time, it would be unjust to pass by the fact of the flight
without according to Curtiss due recognition of the way in which he paid
tribute to the genius of the pioneer by these experiments.

[*] Smithsonian Publications No. 2329.




XIX. THE WAR PERIOD--I

Full record of aeronautical progress and of the accomplishments of
pilots in the years of the War would demand not merely a volume, but a
complete library, and even then it would be barely possible to pay full
tribute to the heroism of pilots of the war period. There are names
connected with that period of which the glory will not fade, names such
as Bishop, Guynemer, Boelcke, Ball, Fonck, Immelmann, and many others
that spring to mind as one recalls the 'Aces' of the period. In
addition to the pilots, there is the stupendous development of the
machines--stupendous when the length of the period in which it was
achieved is considered.

The fact that Germany was best prepared in the matter of
heavier-than-air service machines in spite of the German faith in the
dirigible is one more item of evidence as to who forced hostilities.
The Germans came into the field with well over 600 aeroplanes, mainly
two-seaters of standardised design, and with factories back in the
Fatherland turning out sufficient new machines to make good the
losses. There were a few single-seater scouts built for speed, and the
two-seater machines were all fitted with cameras and bomb-dropping gear.
Manoeuvres had determined in the German mind what should be the uses of
the air fleet; there was photography of fortifications and field works;
signalling by Very lights; spotting for the guns, and scouting for news
of enemy movements. The methodical German mind had arranged all this
beforehand, but had not allowed for the fact that opponents might take
counter-measures which would upset the over-perfect mechanism of the air
service just as effectually as the great march on Paris was countered by
the genius of Joffre.

The French Air Force at the beginning of the War consisted of upwards of
600 machines. These, unlike the Germans, were not standardised, but were
of many and diverse types. In order to get replacements quickly enough,
the factories had to work on the designs they had, and thus for a
long time after the outbreak of hostilities standardisation was an
impossibility. The versatility of a Latin race in a measure compensated
for this; from the outset, the Germans tried to overwhelm the French
Air Force, but failed, since they had not the numerical superiority,
nor--this equally a determining factor--the versatility and resource
of the French pilots. They calculated on a 50 per cent superiority to
ensure success; they needed more nearly 400 per cent, for the German
fought to rule, avoiding risks whenever possible, and definitely
instructed to save both machines and pilots wherever possible. French
pilots, on the other hand, ran all the risks there were, got news
of German movements, bombed the enemy, and rapidly worked up a very
respectable antiaircraft force which, whatever it may have accomplished
in the way of hitting German planes, got on the German pilots' nerves.

It has already been detailed how Britain sent over 82 planes as its
contribution to the military aerial force of 1914. These consisted of
Farman, Caudron, and Short biplanes, together with Bleriot, Deperdussin
and Nieuport monoplanes, certain R.A.F. types, and other machines of
which even the name barely survives--the resourceful Yankee entitles
them 'orphans.' It is on record that the work of providing spares might
have been rather complicated but for the fact that there were none.

There is no doubt that the Germans had made study of aerial
military needs just as thoroughly as they had perfected their ground
organisation. Thus there were 21 illuminated aircraft stations in
Germany before the War, the most powerful being at Weimar, where a
revolving electric flash of over 27 million candle-power was located.
Practically all German aeroplane tests in the period immediately
preceding the War were of a military nature, and quite a number of
reliability tests were carried out just on the other side of the French
frontier. Night flying and landing were standardised items in the German
pilot's course of instruction while they were still experimental in
other countries, and a system of signals was arranged which rendered the
instructional course as perfect as might be.

The Belgian contribution consisted of about twenty machines fit for
active service and another twenty which were more or less useful as
training machines. The material was mainly French, and the Belgian
pilots used it to good account until German numbers swamped them.
France, and to a small extent England, kept Belgian aviators supplied
with machines throughout the War.

The Italian Air Fleet was small, and consisted of French machines
together with a percentage of planes of Italian origin, of which the
design was very much a copy of French types. It was not until the War
was nearing its end that the military and naval services relied more
on the home product than on imports. This does not apply to engines,
however, for the F.I.A.T. and S.C.A.T. were equal to practically any
engine of Allied make, both in design and construction.

Russia spent vast sums in the provision of machines: the giant Sikorsky
biplane, carrying four 100 horsepower Argus motors, was designed by
a young Russian engineer in the latter part of 1913, and in its early
trials it created a world's record by carrying seven passengers for
1 hour 54 minutes. Sikorsky also designed several smaller machines,
tractor biplanes on the lines of the British B.E. type, which were
very successful. These were the only home productions, and the imports
consisted mainly of French aeroplanes by the hundred, which got as
far as the docks and railway sidings and stayed there, while German
influence and the corruption that ruined the Russian Army helped to lose
the War. A few Russian aircraft factories were got into operation as
hostilities proceeded, but their products were negligible, and it is not
on record that Russia ever learned to manufacture a magneto.

The United States paid tribute to British efficiency by adopting the
British system of training for its pilots; 500 American cadets were
trained at the School of Military Aeronautics at oxford, in order to
form a nucleus for the American aviation schools which were subsequently
set up in the United States and in France. As regards production of
craft, the designing of the Liberty engine and building of over 20,000
aeroplanes within a year proves that America is a manufacturing country,
even under the strain of war.

There were three years of struggle for aerial supremacy, the combatants
being England and France against Germany, and the contest was neck
and neck all the way. Germany led at the outset with the standardised
two-seater biplanes manned by pilots and observers, whose training
was superior to that afforded by any other nation, while the machines
themselves were better equipped and fitted with accessories. All the
early German aeroplanes were designated Taube by the uninitiated, and
were formed with swept-back, curved wings very much resembling the wings
of a bird. These had obvious disadvantages, but the standardisation
of design and mass production of the German factories kept them in the
field for a considerable period, and they flew side by side with tractor
biplanes of improved design. For a little time, the Fokker monoplane
became a definite threat both to French and British machines. It was
an improvement on the Morane French monoplane, and with a high-powered
engine it climbed quickly and flew fast, doing a good deal of damage for
a brief period of 1915. Allied design got ahead of it and finally drove
it out of the air.

German equipment at the outset, which put the Allies at a disadvantage,
included a hand-operated magneto engine-starter and a small independent
screw which, mounted on one of the main planes, drove the dynamo used
for the wireless set. Cameras were fitted on practically every machine;
equipment included accurate compasses and pressure petrol gauges, speed
and height recording instruments, bomb-dropping fittings and sectional
radiators which facilitated repairs and gave maximum engine efficiency
in spite of variations of temperature. As counter to these, the Allied
pilots had resource amounting to impudence. In the early days they
carried rifles and hand grenades and automatic pistols. They loaded
their machines down, often at their own expense, with accessories and
fittings until their aeroplanes earned their title of Christmas trees.
They played with death in a way that shocked the average German pilot
of the War's early stages, declining to fight according to rule and
indulging in the individual duels of the air which the German hated.
As Sir John French put it in one of his reports, they established a
personal ascendancy over the enemy, and in this way compensated for
their inferior material.

French diversity of design fitted in well with the initiative and
resource displayed by the French pilots. The big Caudron type was the
ideal bomber of the early days; Farman machines were excellent for
reconnaissance and artillery spotting; the Bleriots proved excellent
as fighting scouts and for aerial photography; the Nieuports made good
fighters, as did the Spads, both being very fast craft, as were the
Morane-Saulnier monoplanes, while the big Voisin biplanes rivalled the
Caudron machines as bombers.

The day of the Fokker ended when the British B.E.2.C. aeroplane came
to France in good quantities, and the F.E. type, together with the De
Havilland machines, rendered British aerial superiority a certainty.
Germany's best reply--this was about 1916--was the Albatross biplane,
which was used by Captain Baron von Richthofen for his famous travelling
circus, manned by German star pilots and sent to various parts of the
line to hearten up German troops and aviators after any specially bad
strafe. Then there were the Aviatik biplane and the Halberstadt fighting
scout, a cleanly built and very fast machine with a powerful engine with
which Germany tried to win back superiority in the third year of the
War, but Allied design kept about three months ahead of that of the
enemy, once the Fokker had been mastered, and the race went on. Spads
and Bristol fighters, Sopwith scouts and F.E.'s played their part in the
race, and design was still advancing when peace came.

The giant twin-engined Handley-Page bomber was tried out, proved
efficient, and justly considered better than anything of its kind that
had previously taken the field. Immediately after the conclusion of its
trials, a specimen of the type was delivered intact at Lille for the
Germans to copy, the innocent pilot responsible for the delivery doing
some great disservice to his own cause. The Gotha Wagon-Fabrik Firm
immediately set to work and copied the Handley-Page design, producing
the great Gotha bombing machine which was used in all the later raids on
England as well as for night work over the Allied lines.

How the War advanced design may be judged by comparison of the military
requirements given for the British Military Trials of 1912, with
performances of 1916 and 1917, when the speed of the faster machines had
increased to over 150 miles an hour and Allied machines engaged enemy
aircraft at heights ranging up to 22,000 feet. All pre-war records of
endurance, speed, and climb went by the board, as the race for aerial
superiority went on.

Bombing brought to being a number of crude devices in the first year of
the War. Allied pilots of the very early days carried up bombs packed
in a small box and threw them over by hand, while, a little later, the
bombs were strung like apples on wings and undercarriage, so that
the pilot who did not get rid of his load before landing risked an
explosion. Then came a properly designed carrying apparatus, crude but
fairly efficient, and with 1916 development had proceeded as far as the
proper bomb-racks with releasing gear.

Reconnaissance work developed, so that fighting machines went as escort
to observing squadrons and scouting operations were undertaken up to 100
miles behind the enemy lines; out of this grew the art of camouflage,
when ammunition dumps were painted to resemble herds of cows, guns were
screened by foliage or painted to merge into a ground scheme, and many
other schemes were devised to prevent aerial observation. Troops were
moved by night for the most part, owing to the keen eyes of the air
pilots and the danger of bombs, though occasionally the aviator had his
chance. There is one story concerning a British pilot who, on returning
from a reconnaissance flight, observed a German Staff car on the road
under him; he descended and bombed and machine--gunned the car until the
German General and his chauffeur abandoned it, took to their heels, and
ran like rabbits. Later still, when Allied air superiority was assured,
there came the phase of machine-gunning bodies of enemy troops from the
air. Disregarding all antiaircraft measures, machines would sweep down
and throw battalions into panic or upset the military traffic along a
road, demoralising a battery or a transport train and causing as much
damage through congestion of traffic as with their actual machine-gun
fire. Aerial photography, too, became a fine art; the ordinary long
focus cameras were used at the outset with automatic plate changers, but
later on photographing aeroplanes had cameras of wide angle lens type
built into the fuselage. These were very simply operated, one lever
registering the exposure and changing the plate. In many cases, aerial
photographs gave information which the human eye had missed, and it is
noteworthy that photographs of ground showed when troops had marched
over it, while the aerial observer was quite unable to detect the marks
left by their passing.

Some small mention must be made of seaplane activities, which, round
the European coasts involved in the War, never ceased. The submarine
campaign found in the spotting seaplane its greatest deterrent, and it
is old news now how even the deeply submerged submarines were easily
picked out for destruction from a height and the news wirelessed from
seaplane to destroyer, while in more than one place the seaplane itself
finished the task by bomb dropping. It was a seaplane that gave Admiral
Beatty the news that the whole German Fleet was out before the Jutland
Battle, news which led to a change of plans that very nearly brought
about the destruction of Germany's naval power. For the most part, the
seaplanes of the War period were heavier than the land machines and, in
the opinion of the land pilots, were slow and clumsy things to fly. This
was inevitable, for their work demanded more solid building and greater
reliability. To put the matter into Hibernian phrase, a forced landing
at sea is a much more serious matter than on the ground. Thus there was
need for greater engine power, bigger wingspread to support the floats,
and fuel tanks of greater capacity. The flying boats of the later
War period carried considerable crews, were heavily armed, capable of
withstanding very heavy weather, and carried good loads of bombs on
long cruises. Their work was not all essentially seaplane work, for the
R.N.A.S. was as well known as hated over the German airship sheds in
Belgium and along the Flanders coast. As regards other theatres of War,
they rendered valuable service from the Dardanelles to the Rufiji River,
at this latter place forming a principal factor in the destruction of
the cruiser Konigsberg. Their spotting work at the Dardanelles for
the battleships was responsible for direct hits from 15 in. guns on
invisible targets at ranges of over 12,000 yards. Seaplane pilots were
bombing specialists, including among their targets army headquarters,
ammunition dumps, railway stations, submarines and their bases, docks,
shipping in German harbours, and the German Fleet at Wilhelmshaven.
Dunkirk, a British seaplane base, was a sharp thorn in the German side.

Turning from consideration of the various services to the exploits of
the men composing them, it is difficult to particularise. A certain
inevitable prejudice even at this length of time leads one to discount
the valour of pilots in the German Air Service, but the names of
Boelcke, von Richthofen, and Immelmann recur as proof of the courage
that was not wanting in the enemy ranks, while, however much we may
decry the Gotha raids over the English coast and on London, there is no
doubt that the men who undertook these raids were not deficient in the
form of bravery that is of more value than the unthinking valour of
a minute which, observed from the right quarter, wins a military
decoration.

Yet the fact that the Allied airmen kept the air at all in the early
days proved on which side personal superiority lay, for they were
outnumbered, out-manoeuvred, and faced by better material than any
that they themselves possessed; yet they won their fights or died. The
stories of their deeds are endless; Bishop, flying alone and meeting
seven German machines and crashing four; the battle of May 5th, 1915,
when five heroes fought and conquered twenty-seven German machines,
ranging in altitude between 12,000 and 3,000 feet, and continuing the
extraordinary struggle from five until six in the evening. Captain
Aizlewood, attacking five enemy machines with such reckless speed that
he rammed one and still reached his aerodrome safely--these are items in
a long list of feats of which the character can only be realised when
it is fully comprehended that the British Air Service accounted for some
8,000 enemy machines in the course of the War. Among the French there
was Captain Guynemer, who at the time of his death had brought down
fifty-four enemy machines, in addition to many others of which the
destruction could not be officially confirmed. There was Fonck, who
brought down six machines in one day, four of them within two minutes.

There are incredible stories, true as incredible, of shattered men
carrying on with their work in absolute disregard of physical injury.
Major Brabazon Rees, V.C., engaged a big German battle-plane in
September of 1915 and, single-handed, forced his enemy out of action.
Later in his career, with a serious wound in the thigh from which blood
was pouring, he kept up a fight with an enemy formation until he had not
a round of ammunition left, and then returned to his aerodrome to get
his wound dressed. Lieutenants Otley and Dunning, flying in the Balkans,
engaged a couple of enemy machines and drove them off, but not until
their petrol tank had got a hole in it and Dunning was dangerously
wounded in the leg. Otley improvised a tourniquet, passed it to Dunning,
and, when the latter had bandaged himself, changed from the observer's
to the pilot's seat, plugged the bullet hole in the tank with his thumb
and steered the machine home.

These are incidents; the full list has not been, and can never be
recorded, but it goes to show that in the pilot of the War period there
came to being a new type of humanity, a product of evolution which
fitted a certain need. Of such was Captain West, who, engaging hostile
troops, was attacked by seven machines. Early in the engagement, one of
his legs was partially severed by an explosive bullet and fell powerless
into the controls, rendering the machine for the time unmanageable.
Lifting his disabled leg, he regained control of the machine, and
although wounded in the other leg, he manoeuvred his machine so
skilfully that his observer was able to get several good bursts into the
enemy machines, driving them away. Then, desperately wounded as he
was, Captain West brought the machine over to his own lines and landed
safely. He fainted from loss of blood and exhaustion, but on regaining
consciousness, insisted on writing his report. Equal to this was the
exploit of Captain Barker, who, in aerial combat, was wounded in the
right and left thigh and had his left arm shattered, subsequently
bringing down an enemy machine in flames, and then breaking through
another hostile formation and reaching the British lines.

In recalling such exploits as these, one is tempted on and on, for it
seems that the pilots rivalled each other in their devotion to duty,
this not confined to British aviators, but common practically to all
services. Sufficient instances have been given to show the nature of the
work and the character of the men who did it.

The rapid growth of aerial effort rendered it necessary in January of
1915 to organise the Royal Flying Corps into separate wings, and in
October of the same year it was constituted in Brigades. In 1916 the
Air Board was formed, mainly with the object of co-ordinating effort
and ensuring both to the R.N.A.S. and to the R.F.C. adequate supplies of
material as far as construction admitted. Under the presidency of Lord
Cowdray, the Air Board brought about certain reforms early in 1917,
and in November of that year a separate Air Ministry was constituted,
separating the Air Force from both Navy and Army, and rendering it an
independent force. On April 1st, 1918, the Royal Air Force came into
existence, and unkind critics in the Royal Flying Corps remarked on the
appropriateness of the date. At the end of the War, the personnel of the
Royal Air Force amounted to 27,906 officers, and 263,842 other ranks.
Contrast of these figures with the number of officers and men who took
the field in 1914 is indicative of the magnitude of British aerial
effort in the War period.




XX. THE WAR PERIOD--II

There was when War broke out no realisation on the part of the British
Government of the need for encouraging the enterprise of private
builders, who carried out their work entirely at their-own cost. The
importance of a supply of British-built engines was realised before the
War, it is true, and a competition was held in which a prize of L5,000
was offered for the best British engine, but this awakening was so late
that the R.F.C. took the field without a single British power plant.
Although Germany woke up equally late to the need for home produced
aeroplane engines, the experience gained in building engines for
dirigibles sufficed for the production of aeroplane power plants. The
Mercedes filled all requirements together with the Benz and the Maybach.
There was a 225 horsepower Benz which was very popular, as were the 100
horse-power and 170 horse-power Mercedes, the last mentioned fitted to
the Aviatik biplane of 1917. The Uberursel was a copy of the Gnome and
supplied the need for rotary engines.

In Great Britain there were a number of aeroplane constructing firms
that had managed to emerge from the lean years 1912-1913 with
sufficient manufacturing plant to give a hand in making up the leeway of
construction when War broke out. Gradually the motor-car firms came
in, turning their body-building departments to plane and fuselage
construction, which enabled them to turn out the complete planes engined
and ready for the field. The coach-building trade soon joined in and
came in handy as propeller makers; big upholstering and furniture firms
and scores of concerns that had never dreamed of engaging in aeroplane
construction were busy on supplying the R.F.C. By 1915 hundreds of
different firms were building aeroplanes and parts; by 1917 the number
had increased to over 1,000, and a capital of over a million pounds for
a firm that at the outbreak of War had employed a score or so of hands
was by no means uncommon. Women and girls came into the work, more
especially in plane construction and covering and doping, though they
took their place in the engine shops and proved successful at acetylene
welding and work at the lathes. It was some time before Britain was able
to provide its own magnetos, for this key industry had been left in
the hands of the Germans up to the outbreak of War, and the 'Bosch' was
admittedly supreme--even now it has never been beaten, and can only be
equalled, being as near perfection as is possible for a magneto.

One of the great inventions of the War was the synchronisation of
engine-timing and machine gun, which rendered it possible to fire
through the blades of a propeller without damaging them, though the
growing efficiency of the aeroplane as a whole and of its armament is
a thing to marvel at on looking back and considering what was actually
accomplished. As the efficiency of the aeroplane increased, so
anti-aircraft guns and range-finding were improved. Before the War an
aeroplane travelling at full speed was reckoned perfectly safe at 4,000
feet, but, by the first month of 1915, the safe height had gone up to
9,000 feet, 7,000 feet being the limit of rifle and machine gun bullet
trajectory; the heavier guns were not sufficiently mobile to tackle
aircraft. At that time, it was reckoned that effective aerial
photography ceased at 6,000 feet, while bomb-dropping from 7,000-8,000
feet was reckoned uncertain except in the case of a very large target.
The improvement in anti-aircraft devices went on, and by May of 1916, an
aeroplane was not safe under 15,000 feet, while anti-aircraft shells had
fuses capable of being set to over 20,000 feet, and bombing from 15,000
and 16,000 feet was common. It was not till later that Allied pilots
demonstrated the safety that lies in flying very near the ground, this
owing to the fact that, when flying swiftly at a very low altitude, the
machine is out of sight almost before it can be aimed at.

The Battle of the Somme and the clearing of the air preliminary to that
operation brought the fighting aeroplane pure and simple with them.
Formations of fighting planes preceded reconnaissance craft in order
to clear German machines and observation balloons out of the sky and to
watch and keep down any further enemy formations that might attempt
to interfere with Allied observation work. The German reply to this
consisted in the formation of the Flying Circus, of which Captain Baron
von Richthofen's was a good example. Each circus consisted of a large
formation of speedy machines, built specially for fighting and manned
by the best of the German pilots. These were sent to attack at any point
along the line where the Allies had got a decided superiority.

The trick flying of pre-war days soon became an everyday matter; Pegoud
astonished the aviation world before the War by first looping the loop,
but, before three years of hostilities had elapsed, looping was part of
the training of practically every pilot, while the spinning nose dive,
originally considered fatal, was mastered, and the tail slide, which
consisted of a machine rising nose upward in the air and falling back on
its tail, became one of the easiest 'stunts' in the pilot's repertoire.
Inherent stability was gradually improved, and, from 1916 onward,
practically every pilot could carry on with his machine-gun or camera
and trust to his machine to fly itself until he was free to attend to
it. There was more than one story of a machine coming safely to earth
and making good landing on its own account with the pilot dead in his
cock-pit.

Toward the end of the War, the Independent Air Force was formed as a
branch of the R.A.F. with a view to bombing German bases and devoting
its attention exclusively to work behind the enemy lines. Bombing
operations were undertaken by the R.N.A.S. as early as 1914-1915 against
Cuxhaven, Dusseldorf, and Friedrichshavn, but the supply of material was
not sufficient to render these raids continuous. A separate Brigade,
the 8th, was formed in 1917 to harass the German chemical and iron
industries, the base being in the Nancy area, and this policy was found
so fruitful that the Independent Force was constituted on the 8th June,
1918. The value of the work accomplished by this force is demonstrated
by the fact that the German High Command recalled twenty fighting
squadrons from the Western front to counter its activities, and, in
addition, took troops away from the fighting line in large numbers for
manning anti-aircraft batteries and searchlights. The German press of
the last year of the War is eloquent of the damage done in manufacturing
areas by the Independent Force, which, had hostilities continued a
little longer, would have included Berlin in its activities.

Formation flying was first developed by the Germans, who made use of it
in the daylight raids against England in 1917. Its value was very soon
realised, and the V formation of wild geese was adopted, the leader
taking the point of the V and his squadron following on either side at
different heights. The air currents set up by the leading machines were
thus avoided by those in the rear, while each pilot had a good view
of the leader's bombs, and were able to correct their own aim by
the bursts, while the different heights at which they flew rendered
anti-aircraft gun practice less effective. Further, machines were able
to afford mutual protection to each other and any attacker would be
met by machine-gun fire from three or four machines firing on him from
different angles and heights. In the later formations single-seater
fighters flew above the bombers for the purpose of driving off hostile
craft. Formation flying was not fully developed when the end of the War
brought stagnation in place of the rapid advance in the strategy and
tactics of military air work.




XXI. RECONSTRUCTION

The end of the War brought a pause in which the multitude of aircraft
constructors found themselves faced with the possible complete
stagnation of the industry, since military activities no longer demanded
their services and the prospects of commercial flying were virtually
nil. That great factor in commercial success, cost of plant and upkeep,
had received no consideration whatever in the War period, for armies do
not count cost. The types of machines that had evolved from the War
were very fast, very efficient, and very expensive, although the bombers
showed promise of adaptation to commercial needs, and, so far as other
machines were concerned, America had already proved the possibilities of
mail-carrying by maintaining a mail service even during the War period.

A civil aviation department of the Air Ministry was formed in February
of 1919 with a Controller General of Civil Aviation at the head. This
was organised into four branches, one dealing with the survey and
preparation of air routes for the British Empire, one organising
meteorological and wireless telegraphy services, one dealing with the
licensing of aerodromes, machines for passenger or goods carrying and
civilian pilots, and one dealing with publicity and transmission of
information generally. A special Act of Parliament 264 entitled 'The Air
Navigation Acts, 1911-1919,' was passed on February 27th, and commercial
flying was officially permitted from May 1st, 1919.

Meanwhile the great event of 1919, the crossing of the Atlantic by air,
was gradually ripening to performance. In addition to the rigid airship,
R.34, eight machines entered for this flight, these being a Short
seaplane, Handley-Page, Martinsyde, Vickers-Vimy, and Sopwith
aeroplanes, and three American flying boats, N.C.1, N.C.3, and N.C.4.
The Short seaplane was the only one of the eight which proposed to make
the journey westward; in flying from England to Ireland, before starting
on the long trip to Newfoundland, it fell into the sea off the coast of
Anglesey, and so far as it was concerned the attempt was abandoned.

The first machines to start from the Western end were the three American
seaplanes, which on the morning of May 6th left Trepassy, Newfoundland,
on the 1,380 mile stage to Horta in the Azores. N.C.1 and N.C.3 gave
up the attempt very early, but N.C.4, piloted by Lieut.-Commander Read,
U.S.N., made Horta on May 17th and made a three days' halt. On the 20th
the second stage of the journey to Ponta Delgada, a further 190 miles,
was completed and a second halt of a week was made. On the 27th, the
machine left for Lisbon, 900 miles distant, and completed the journey in
a day. On the 30th a further stage of 340 miles took N.C.4 on to
Ferrol, and the next day the last stage of 420 miles to Plymouth was
accomplished.

Meanwhile, H. G. Hawker, pilot of the Sopwith biplane, together with
Commander Mackenzie Grieve, R.N., his navigator, found the weather
sufficiently auspicious to set out at 6.48 p.m. On Sunday, May 18th, in
the hope of completing the trip by the direct route before N.C.4 could
reach Plymouth. They set out from Mount Pearl aerodrome, St John's,
Newfoundland, and vanished into space, being given up as lost, as Hamel
was lost immediately before the War in attempting to fly the North
Sea. There was a week of dead silence regarding their fate, but on the
following Sunday morning there was world-wide relief at the news that
the plucky attempt had not ended in disaster, but both aviators had been
picked up by the steamer Mary at 9.30 a.m. on the morning of the 19th,
while still about 750 miles short of the conclusion of their journey.
Engine failure brought them down, and they planed down to the sea close
to the Mary to be picked up; as the vessel was not fitted with wireless,
the news of their rescue could not be communicated until land was
reached. An equivalent of half the L10,000 prize offered by the Daily
Mail for the non-stop flight was presented by the paper in recognition
of the very gallant attempt, and the King conferred the Air Force Cross
on both pilot and navigator.

Raynham, pilot of the Martinsyde competing machine, had the bad luck to
crash his craft twice in attempting to start before he got outside the
boundary of the aerodrome. The Handley-Page machine was withdrawn from
the competition, and, attempting to fly to America, was crashed on the
way.

The first non-stop crossing was made on June 14th-15th in 16 hours 27
minutes, the speed being just over 117 miles per hour. The machine was a
Vickers-Vimy bomber, engined with two Rolls-Royce Eagle VIII's, piloted
by Captain John Alcock, D.S.C., with Lieut. Arthur Whitten-Brown as
navigator. The journey was reported to be very rough, so much so at
times that Captain Alcock stated that they were flying upside down, and
for the greater part of the time they were out of sight of the sea. Both
pilot and navigator had the honour of knighthood conferred on them at
the conclusion of the journey.

Meanwhile, commercial flying opened on May 8th (the official date
was May 1st) with a joy-ride service from Hounslow of Avro training
machines. The enterprise caught on remarkably, and the company extended
their activities to coastal resorts for the holiday season--at Blackpool
alone they took up 10,000 passengers before the service was two months
old. Hendon, beginning passenger flights on the same date, went in for
exhibition and passenger flying, and on June 21st the aerial Derby
was won by Captain Gathergood on an Airco 4R machine with a Napier 450
horse-power 'Lion' engine; incidentally the speed of 129.3 miles per
hour was officially recognised as constituting the world's record for
speed within a closed circuit. On July 17th a Fiat B.R. biplane with a
700 horse-power engine landed at Kenley aerodrome after having made a
non-stop flight of 1,100 miles. The maximum speed of this machine was
160 miles per hour, and it was claimed to be the fastest machine in
existence. On August 25th a daily service between London and Paris was
inaugurated by the Aircraft Manufacturing Company, Limited, who ran a
machine each way each day, starting at 12.30 and due to arrive at 2.45
p.m. The Handley-Page Company began a similar service in September
of 1919, but ran it on alternate days with machines capable of
accommodating ten passengers. The single fare in each case was fixed at
15 guineas and the parcel rate at 7s. 6d. per pound.

Meanwhile, in Germany, a number of passenger services had been in
operation from the early part of the year; the Berlin-Weimar service was
established on February 5th and Berlin-Hamburg on March 1st, both for
mail and passenger carrying. Berlin-Breslau was soon added, but the
first route opened remained most popular, 538 flights being made between
its opening and the end of April, while for March and April combined,
the Hamburg-Berlin route recorded only 262 flights. All three routes
were operated by a combine of German aeronautical firms entitled the
Deutsch Luft Rederie. The single fare between Hamburg and Berlin was
450 marks, between Berlin and Breslau 500 marks, and between Berlin
and Weimar 450 marks. Luggage was carried free of charge, but varied
according to the weight of the passenger, since the combined weight of
both passenger and luggage was not allowed to exceed a certain limit.

In America commercial flying had begun in May of 1918 with the mail
service between Washington, Philadelphia, and New York, which proved
that mail carrying is a commercial possibility, and also demonstrated
the remarkable reliability of the modern aeroplane by making 102
complete flights out of a possible total of 104 in November, 1918, at a
cost of 0.777 of a dollar per mile. By March of 1919 the cost per mile
had gone up to 1.28 dollars; the first annual report issued at the
end of May showed an efficiency of 95.6 per cent and the original
six aeroplanes and engines with which the service began were still in
regular use.

In June of 1919 an American commercial firm chartered an aeroplane for
emergency service owing to a New York harbour strike and found it so
useful that they made it a regular service. The Travellers Company
inaugurated a passenger flying boat service between New York and
Atlantic City on July 25th, the fare, inclusive of 35 lbs. of luggage,
being fixed at L25 each way.

Five flights on the American continent up to the end of 1919 are worthy
of note. On December 13th, 1918, Lieut. D. Godoy of the Chilian army
left Santiago, Chili, crossed the Andes at a height of 19,700 feet
and landed at Mendoza, the capital of the wine-growing province of
Argentina. On April 19th, 1919, Captain E. F. White made the first
non-stop flight between New York and Chicago in 6 hours 50 minutes on
a D.H.4 machine driven by a twelve-cylinder Liberty engine. Early in
August Major Schroeder, piloting a French Lepere machine flying at a
height of 18,400 feet, reached a speed of 137 miles per hour with a
Liberty motor fitted with a super-charger. Toward the end of August, Rex
Marshall, on a Thomas-Morse biplane, starting from a height of 17,000
feet, made a glide of 35 miles with his engine cut off, restarting it
when at a height of 600 feet above the ground. About a month later R.
Rohlfe, piloting a Curtiss triplane, broke the height record by reaching
34,610 feet.




XXII. 1919-20

Into the later months of 1919 comes the flight by Captain Ross-Smith
from England to Australia and the attempt to make the Cape to Cairo
voyage by air. The Australian Government had offered a prize of L10,000
for the first flight from England to Australia in a British machine, the
flight to be accomplished in 720 consecutive hours. Ross-Smith, with his
brother, Lieut. Keith Macpherson Smith, and two mechanics, left Hounslow
in a Vickers-Vimy bomber with Rolls-Royce engine on November 12th and
arrived at Port Darwin, North Australia, on the 10th December, having
completed the flight in 27 days 20 hours 20 minutes, thus having 51
hours 40 minutes to spare out of the 720 allotted hours.

Early in 1920 came a series of attempts at completing the journey by air
between Cairo and the Cape. Out of four competitors Colonel Van Ryneveld
came nearest to making the journey successfully, leaving England on
a standard Vickers-Vimy bomber with Rolls-Royce engines, identical in
design with the machine used by Captain Ross-Smith on the England
to Australia flight. A second Vickers-Vimy was financed by the Times
newspaper and a third flight was undertaken with a Handley-Page machine
under the auspices of the Daily Telegraph. The Air Ministry had already
prepared the route by means of three survey parties which cleared the
aerodromes and landing grounds, dividing their journey into stages of
200 miles or less. Not one of the competitors completed the course, but
in both this and Ross-Smith's flight valuable data was gained in
respect of reliability of machines and engines, together with a mass of
meteorological information.

The Handley-Page Company announced in the early months of 1920 that they
had perfected a new design of wing which brought about a twenty to forty
per cent improvement in lift rate in the year. When the nature of the
design was made public, it was seen to consist of a division of the
wing into small sections, each with its separate lift. A few days later,
Fokker, the Dutch inventor, announced the construction of a machine in
which all external bracing wires are obviated, the wings being of a
very deep section and self-supporting. The value of these two inventions
remains to be seen so far as commercial flying is concerned.

The value of air work in war, especially so far as the Colonial
campaigns in which British troops are constantly being engaged is in
question, was very thoroughly demonstrated in a report issued early
in 1920 with reference to the successful termination of the Somaliland
campaign through the intervention of the Royal Air Force, which between
January 21st and the 31st practically destroyed the Dervish force under
the Mullah, which had been a thorn in the side of Britain since 1907.
Bombs and machine-guns did the work, destroying fortifications and
bringing about the surrender of all the Mullah's following, with the
exception of about seventy who made their escape.

Certain records both in construction and performance had characterised
the post-war years, though as design advances and comes nearer to
perfection, it is obvious that records must get fewer and farther
between. The record aeroplane as regards size at the time of its
construction was the Tarrant triplane, which made its first--and
last--flight on May 28th, 1919. The total loaded weight was 30 tons,
and the machine was fitted with six 400 horse-power engines; almost
immediately after the trial flight began, the machine pitched forward
on its nose and was wrecked, causing fatal injuries to Captains Dunn
and Rawlings, who were aboard the machine. A second accident of
similar character was that which befell the giant seaplane known as the
Felixstowe Fury, in a trial flight. This latter machine was intended to
be flown to Australia, but was crashed over the water.

On May 4th, 1920, a British record for flight duration and useful
load was established by a commercial type Handley-Page biplane, which,
carrying a load of 3,690 lbs., rose to a height of 13,999 feet and
remained in the air for 1 hour 20 minutes. On May 27th the French pilot,
Fronval, flying at Villacoublay in a Morane-Saulnier type of biplane
with Le Rhone motor, put up an extraordinary type of record by looping
the loop 962 times in 3 hours 52 minutes 10 seconds. Another record of
the year of similar nature was that of two French fliers, Boussotrot
and Bernard, who achieved a continuous flight of 24 hours 19 minutes 7
seconds, beating the pre-war record of 21 hours 48 3/4 seconds set up
by the German pilot, Landemann. Both these records are likely to stand,
being in the nature of freaks, which demonstrate little beyond the
reliability of the machine and the capacity for endurance on the part of
its pilots.

Meanwhile, on February 14th, Lieuts. Masiero and Ferrarin left Rome on
S.V.A. Ansaldo V. machines fitted with 220 horse-power S.V.A. motors. On
May 30th they arrived at Tokio, having flown by way of Bagdad, Karachi,
Canton, Pekin, and Osaka. Several other competitors started, two of whom
were shot down by Arabs in Mesopotamia.

Considered in a general way, the first two years after the termination
of the Great European War form a period of transition in which the
commercial type of aeroplane was gradually evolved from the fighting
machine which was perfected in the four preceding years. There was about
this period no sense of finality, but it was as experimental, in its
own way, as were the years of progressing design which preceded the war
period. Such commercial schemes as were inaugurated call for no more
note than has been given here; they have been experimental, and, with
the possible exception of the United States Government mail service,
have not been planned and executed on a sufficiently large scale to
furnish reliable data on which to forecast the prospects of commercial
aviation. And there is a school rapidly growing up which asserts that
the day of aeroplanes is nearly over. The construction of the giant
airships of to-day and the successful return flight of R34 across
the Atlantic seem to point to the eventual triumph, in spite of its
disadvantages, of the dirigible airship.

This is a hard saying for such of the aeroplane industry as survived
the War period and consolidated itself, and it is but the saying of a
section which bases its belief on the fact that, as was noted in the
very early years of the century, the aeroplane is primarily a war
machine. Moreover, the experience of the War period tended to discredit
the dirigible, since, before the introduction of helium gas,
the inflammability of its buoyant factor placed it at an immense
disadvantage beside the machine dependent on the atmosphere itself for
its lift.

As life runs to-day, it is a long time since Kipling wrote his story of
the airways of a future world and thrust out a prophecy that the bulk
of the world's air traffic would be carried by gas-bag vessels. If the
school which inclines to belief in the dirigible is right in its belief,
as it well may be, then the foresight was uncannily correct, not only
in the matter of the main assumption, but in the detail with which the
writer embroidered it.

On the constructional side, the history of the aeroplane is still so
much in the making that any attempt at a critical history would be
unwise, and it is possible only to record fact, leaving it to the future
for judgment to be passed. But, in a general way, criticism may
be advanced with regard to the place that aeronautics takes in
civilisation. In the past hundred years, the world has made miraculously
rapid strides materially, but moral development has not kept abreast.
Conception of the responsibilities of humanity remains virtually in a
position of a hundred years ago; given a higher conception of life and
its responsibilities, the aeroplane becomes the crowning achievement
of that long series which James Watt inaugurated, the last step in
intercommunication, the chain with which all nations are bound in
a growing prosperity, surely based on moral wellbeing. Without such
conception of the duties as well as the rights of life, this last
achievement of science may yet prove the weapon that shall end
civilisation as men know it to-day, and bring this ultra-material age to
a phase of ruin on which saner people can build a world more reasonable
and less given to groping after purely material advancement.




PART II. 1903-1920: PROGRESS IN DESIGN

By Lieut.-Col. W. Lockwood Marsh




I. THE BEGINNINGS

Although the first actual flight of an aeroplane was made by the Wrights
on December 17th 1903, it is necessary, in considering the progress
of design between that period and the present day, to go back to
the earlier days of their experiments with 'gliders,' which show the
alterations in design made by them in their step-bystep progress to a
flying machine proper, and give a clear idea of the stage at which they
had arrived in the art of aeroplane design at the time of their first
flights.

They started by carefully surveying the work of previous experimenters,
such as Lilienthal and Chanute, and from the lesson of some of the
failures of these pioneers evolved certain new principles which were
embodied in their first glider, built in 1900. In the first place,
instead of relying upon the shifting of the operator's body to obtain
balance, which had proved too slow to be reliable, they fitted in front
of the main supporting surfaces what we now call an 'elevator,' which
could be flexed, to control the longitudinal balance, from where the
operator lay prone upon the main supporting surfaces. The second
main innovation which they incorporated in this first glider, and the
principle of which is still used in every aeroplane in existence, was
the attainment of lateral balance by warping the extremities of the main
planes. The effect of warping or pulling down the extremity of the wing
on one side was to increase its lift and so cause that side to rise. In
the first two gliders this control was also used for steering to right
and left. Both these methods of control were novel for other than model
work, as previous experimenters, such as Lilienthal and Pilcher, had
relied entirely upon moving the legs or shifting the position of the
body to control the longitudinal and lateral motions of their gliders.
For the main supporting surfaces of the glider the biplane system of
Chanute's gliders was adopted with certain modifications, while the
curve of the wings was founded upon the calculations of Lilienthal as to
wind pressure and consequent lift of the plane.

This first glider was tested on the Kill Devil Hill sand-hills in North
Carolina in the summer of 1900 and proved at any rate the correctness
of the principles of the front elevator and warping wings, though its
designers were puzzled by the fact that the lift was less than they
expected; whilst the 'drag'(as we call it), or resistance, was also
considerably lower than their predictions. The 1901 machine was, in
consequence, nearly doubled in area--the lifting surface being increased
from 165 to 308 square feet--the first trial taking place on July 27th,
1901, again at Kill Devil Hill. It immediately appeared that something
was wrong, as the machine dived straight to the ground, and it was only
after the operator's position had been moved nearly a foot back from
what had been calculated as the correct position that the machine would
glide--and even then the elevator had to be used far more strongly than
in the previous year's glider. After a good deal of thought the apparent
solution of the trouble was finally found.

This consisted in the fact that with curved surfaces, while at large
angles the centre of pressure moves forward as the angle decreases, when
a certain limit of angle is reached it travels suddenly backwards and
causes the machine to dive. The Wrights had known of this tendency from
Lilienthal's researches, but had imagined that the phenomenon would
disappear if they used a fairly lightly cambered--or curved--surface
with a very abrupt curve at the front. Having discovered what appeared
to be the cause they surmounted the difficulty by 'trussing down' the
camber of the wings, with the result that they at once got back to
the old conditions of the previous year and could control the machine
readily with small movements of the elevator, even being able to follow
undulations in the ground. They still found, however, that the lift was
not as great as it should have been; while the drag remained, as in
the previous glider, surprisingly small. This threw doubt on previous
figures as to wind resistance and pressure on curved surfaces; but
at the same time confirmed (and this was a most important result)
Lilienthal's previously questioned theory that at small angles the
pressure on a curved surface instead of being normal, or at right angles
to, the chord is in fact inclined in front of the perpendicular. The
result of this is that the pressure actually tends to draw the machine
forward into the wind--hence the small amount of drag, which had puzzled
Wilbur and Orville Wright.

Another lesson which was learnt from these first two years of
experiment, was that where, as in a biplane, two surfaces are superposed
one above the other, each of them has somewhat less lift than it would
have if used alone. The experimenters were also still in doubt as to the
efficiency of the warping method of controlling the lateral balance
as it gave rise to certain phenomena which puzzled them, the machine
turning towards the wing having the greater angle, which seemed also to
touch the ground first, contrary to their expectations. Accordingly,
on returning to Dayton towards the end of 1901, they set themselves to
solve the various problems which had appeared and started on a
lengthy series of experiments to check the previous figures as to wind
resistance and lift of curved surfaces, besides setting themselves
to grapple with the difficulty of lateral control. They accordingly
constructed for themselves at their home in Dayton a wind tunnel 16
inches square by 6 feet long in which they measured the lift and 'drag'
of more than two hundred miniature wings. In the course of these tests
they for the first time produced comparative results of the lift of
oblong and square surfaces, with the result that they re-discovered the
importance of 'aspect ratio'--the ratio of length to breadth of planes.
As a result, in the next year's glider the aspect ration of the wings
was increased from the three to one of the earliest model to about six
to one, which is approximately the same as that used in the machines
of to-day. Further than that, they discussed the question of lateral
stability, and came to the conclusion that the cause of the trouble was
that the effect of warping down one wing was to increase the resistance
of, and consequently slow down, that wing to such an extent that its
lift was reduced sufficiently to wipe out the anticipated increase in
lift resulting from the warping. From this they deduced that if the
speed of the warped wing could be controlled the advantage of increasing
the angle by warping could be utilised as they originally intended.
They therefore decided to fit a vertical fin at the rear which, if the
machine attempted to turn, would be exposed more and more to the wind
and so stop the turning motion by offering increased resistance.

As a result of this laboratory research work the third Wright glider,
which was taken to Kill Devil Hill in September, 1902, was far more
efficient aerodynamically than either of its two predecessors, and was
fitted with a fixed vertical fin at the rear in addition to the movable
elevator in front. According to Mr Griffith Brewer,[*] this third glider
contained 305 square feet of surface; though there may possibly be a
mistake here, as he states[**] the surface of the previous year's glider
to have been only 290 square feet, whereas Wilbur Wright himself[***]
states it to have been 308 square feet. The matter is not, perhaps, save
historically, of much importance, except that the gliders are believed
to have been progressively larger, and therefore if we accept Wilbur
Wright's own figure of the surface of the second glider, the third
must have had a greater area than that given by Mr Griffith Brewer.
Unfortunately, no evidence of the Wright Brothers themselves on this
point is available.

[*] Fourth Wilbur Wright Memorial Lecture, Aeronautical Journal, Vol.
XX, No. 79, page 75.

[**] Ibid. page 73.

[***] Ibid. pp. 91 and 102.

The first glide of the 1902, season was made on September 17th of that
year, and the new machine at once showed itself an improvement on its
predecessors, though subsequent trials showed that the difficulty
of lateral balance had not been entirely overcome. It was decided,
therefore, to turn the vertical fin at the rear into a rudder by making
it movable. At the same time it was realised that there was a definite
relation between lateral balance and directional control, and the rudder
controls and wing-warping wires were accordingly connected This ended
the pioneer gliding experiments of Wilbur and Orville Wright--though
further glides were made in subsequent years--as the following year,
1903, saw the first power-driven machine leave the ground.

To recapitulate--in the course of these original experiments the Wrights
confirmed Lilienthal's theory of the reversal of the centre of pressure
on cambered surfaces at small angles of incidence: they confirmed the
importance of high aspect ratio in respect to lift: they had evolved new
and more accurate tables of lift and pressure on cambered surfaces:
they were the first to use a movable horizontal elevator for controlling
height: they were the first to adjust the wings to different angles of
incidence to maintain lateral balance: and they were the first to use
the movable rudder and adjustable wings in combination.

They now considered that they had gone far enough to justify them in
building a power-driven 'flier,' as they called their first aeroplane.
They could find no suitable engine and so proceeded to build for
themselves an internal combustion engine, which was designed to give
8 horse-power, but when completed actually developed about 12-15
horse-power and weighed 240 lbs. The complete machine weighed about
750 lbs. Further details of the first Wright aeroplane are difficult to
obtain, and even those here given should be received with some caution.
The first flight was made on December 17th 1903, and lasted 12 seconds.
Others followed immediately, and the fourth lasted 59 seconds, a
distance of 852 feet being covered against a 20-mile wind.

The following year they transferred operations to a field outside
Dayton, Ohio (their home), and there they flew a somewhat larger and
heavier machine with which on September 20th 1904, they completed the
first circle in the air. In this machine for the first time the pilot
had a seat; all the previous experiments having been carried out with
the operator lying prone on the lower wing. This was followed next
year by another still larger machine, and on it they carried out many
flights. During the course of these flights they satisfied themselves as
to the cause of a phenomenon which had puzzled them during the previous
year and caused them to fear that they had not solved the problem
of lateral control. They found that on occasions--always when on a
turn--the machine began to slide down towards the ground and that no
amount of warping could stop it. Finally it was found that if the nose
of the machine was tilted down a recovery could be effected; from which
they concluded that what actually happened was that the machine, 'owing
to the increased load caused by centrifugal force,' had insufficient
power to maintain itself in the air and therefore lost speed until a
point was reached at which the controls became inoperative. In other
words, this was the first experience of 'stalling on a turn,' which is a
danger against which all embryo pilots have to guard in the early stages
of their training.

The 1905 machine was, like its predecessors, a biplane with a biplane
elevator in front and a double vertical rudder in rear. The span was 40
feet, the chord of the wings being 6 feet and the gap between them about
the same. The total area was about 600 square feet which supported
a total weight of 925 lbs.; while the motor was 12 to 15 horse-power
driving two propellers on each side behind the main planes through
chains and giving the machine a speed of about 30 m.p.h. one of
these chains was crossed so that the propellers revolved in opposite
directions to avoid the torque which it was feared would be set up
if they both revolved the same way. The machine was not fitted with a
wheeled undercarriage but was carried on two skids, which also acted as
outriggers to carry the elevator. Consequently, a mechanical method of
launching had to be evolved and the machine received initial velocity
from a rail, along which it was drawn by the impetus provided by the
falling of a weight from a wooden tower or 'pylon.' As a result of this
the Wright aeroplane in its original form had to be taken back to its
starting rail after each flight, and could not restart from the point of
alighting. Perhaps, in comparison with French machines of more or less
contemporary date (evolved on independent lines in ignorance of the
Americans' work), the chief feature of the Wright biplane of 1905
was that it relied entirely upon the skill of the operator for its
stability; whereas in France some attempt was being made, although
perhaps not very successfully, to make the machine automatically stable
laterally. The performance of the Wrights in carrying a loading of some
60 lbs. per horse-power is one which should not be overlooked. The wing
loading was about 1 1/2 lbs. per square foot.

About the same time that the Wrights were carrying out their
power-driven experiments, a band of pioneers was quite independently
beginning to approach success in France. In practically every case,
however, they started from a somewhat different standpoint and took
as their basic idea the cellular (or box) kite. This form of kite,
consisting of two superposed surfaces connected at each end by a
vertical panel or curtain of fabric, had proved extremely successful for
man-carrying purposes, and, therefore, it was little wonder that several
minds conceived the idea of attempting to fly by fitting a series
of box-kites with an engine. The first to achieve success was M.
Santos-Dumont, the famous Brazilian pioneer-designer of airships, who,
on November 12th, 1906, made several flights, the last of which covered
a little over 700 feet. Santos-Dumont's machine consisted essentially of
two box-kites, forming the main wings, one on each side of the body, in
which the pilot stood, and at the front extremity of which was another
movable box-kite to act as elevator and rudder. The curtains at the ends
were intended to give lateral stability, which was further ensured by
setting the wings slightly inclined upwards from the centre, so that
when seen from the front they formed a wide V. This feature is still
to be found in many aeroplanes to-day and has come to be known as the
'dihedral.' The motor was at first of 24 horse-power, for which later a
50 horse-power Antoinette engine was substituted; whilst a three-wheeled
undercarriage was provided, so that the machine could start without
external mechanical aid. The machine was constructed of bamboo and
steel, the weight being as low as 352 lbs. The span was 40 feet, the
length being 33 feet, with a total surface of main planes of 860 square
feet. It will thus be seen--for comparison with the Wright machine--that
the weight per horse-power (with the 50 horse-power engine) was only 7
lbs., while the wing loading was equally low at 1/2 lb. per square foot.

The main features of the Santos-Dumont machine were the box-kite form of
construction, with a dihedral angle on the main planes, and the forward
elevator which could be moved in any direction and therefore acted in
the same way as the rudder at the rear of the Wright biplane. It had a
single propeller revolving in the centre behind the wings and was fitted
with an undercarriage incorporated in the machine.

The other chief French experimenters at this period were the Voisin
Freres, whose first two machines--identical in form--were sold to
Delagrange and H. Farman, which has sometimes caused confusion, the two
purchasers being credited with the design they bought. The Voisins, like
the Wrights, based their designs largely on the experimental work of
Lilienthal, Langley, Chanute, and others, though they also carried out
tests on the lifting properties of aerofoils in a wind tunnel of their
own. Their first machines, like those of Santos-Dumont, showed the
effects of experimenting with box-kites, some of which they had built
for M. Ernest Archdeacon in 1904. In their case the machine, which was
again a biplane, had, like both the others previously mentioned, an
elevator in front--though in this case of monoplane form--and, as in
the Wright, a rudder was fitted in rear of the main planes. The Voisins,
however, fitted a fixed biplane horizontal 'tail'--in an effort to
obtain a measure of automatic longitudinal stability--between the two
surfaces of which the single rudder worked. For lateral stability they
depended entirely on end curtains between the upper and lower
surfaces of both the main planes and biplane tail surfaces. They, like
Santos-Dumont, fitted a wheeled undercarriage, so that the machine
was self-contained. The Voisin machine, then, was intended to be
automatically stable in both senses; whereas the Wrights deliberately
produced a machine which was entirely dependent upon the pilot's
skill for its stability. The dimensions of the Voisin may be given for
comparative purposes, and were as follows: Span 33 feet with a chord
(width from back to front) of main planes of 6 1/2 feet, giving a total
area of 430 square feet. The 50 horse-power Antoinette engine, which
was enclosed in the body (or 'nacelle ') in the front of which the pilot
sat, drove a propeller behind, revolving between the outriggers carrying
the tail. The total weight, including Farman as pilot, is given as 1,540
lbs., so that the machine was much heavier than either of the others;
the weight per horse-power being midway between the Santos-Dumont
and the Wright at 31 lbs. per square foot, while the wing loading was
considerably greater than either at 3 1/2 lbs. per square foot. The
Voisin machine was experimented with by Farman and Delagrange from about
June 1907 onwards, and was in the subsequent years developed by Farman;
and right up to the commencement of the War upheld the principles of
the box-kite method of construction for training purposes. The chief
modification of the original design was the addition of flaps (or
ailerons) at the rear extremities of the main planes to give lateral
control, in a manner analogous to the wing-warping method invented by
the Wrights, as a result of which the end curtains between the planes
were abolished. An additional elevator was fitted at the rear of the
fixed biplane tail, which eventually led to the discarding of the front
elevator altogether. During the same period the Wright machine came into
line with the others by the fitting of a wheeled undercarriage integral
with the machine. A fixed horizontal tail was also added to the rear
rudder, to which a movable elevator was later attached; and, finally,
the front elevator was done away with. It will thus be seen that having
started from the very different standpoints of automatic stability and
complete control by the pilot, the Voisin (as developed in the Farman)
and Wright machines, through gradual evolution finally resulted in
aeroplanes of similar characteristics embodying a modicum of both
features.

Before proceeding to the next stage of progress mention should be made
of the experimental work of Captain Ferber in France. This officer
carried out a large number of experiments with gliders contemporarily
with the Wrights, adopting--like them--the Chanute biplane principle. He
adopted the front elevator from the Wrights, but immediately went a step
farther by also fitting a fixed tail in rear, which did not become a
feature of the Wright machine until some seven or eight years later. He
built and appeared to have flown a machine fitted with a motor in 1905,
and was commissioned to go to America by the French War Office on a
secret mission to the Wrights. Unfortunately, no complete account of his
experiments appears to exist, though it can be said that his work was at
least as important as that of any of the other pioneers mentioned.




II. MULTIPLICITY OF IDEAS

In a review of progress such as this, it is obviously impossible, when
a certain stage of development has been reached, owing to the very
multiplicity of experimenters, to continue dealing in anything
approaching detail with all the different types of machines; and it is
proposed, therefore, from this point to deal only with tendencies, and
to mention individuals merely as examples of a class of thought rather
than as personalities, as it is often difficult fairly to allocate the
responsibility for any particular innovation.

During 1907 and 1908 a new type of machine, in the monoplane, began to
appear from the workshops of Louis Bleriot, Robert Esnault-Pelterie, and
others, which was destined to give rise to long and bitter controversies
on the relative advantages of the two types, into which it is not
proposed to enter here; though the rumblings of the conflict are still
to be heard by discerning ears. Bleriot's early monoplanes had certain
new features, such as the location of the pilot, and in some cases the
engine, below the wing; but in general his monoplanes, particularly the
famous No. XI on which the first Channel crossing was made on July
25th, 1909, embodied the main principles of the Wright and Voisin
types, except that the propeller was in front of instead of behind the
supporting surfaces, and was, therefore, what is called a 'tractor' in
place of the then more conventional 'pusher.' Bleriot aimed at lateral
balance by having the tip of each wing pivoted, though he soon fell into
line with the Wrights and adopted the warping system. The main features
of the design of Esnault-Pelterie's monoplane was the inverted dihedral
(or kathedral as this was called in Mr S. F. Cody's British Army Biplane
of 1907) on the wings, whereby the tips were considerably lower than
the roots at the body. This was designed to give automatic lateral
stability, but, here again, conventional practice was soon adopted and
the R.E.P. monoplanes, which became well-known in this country through
their adoption in the early days by Messrs Vickers, were of the ordinary
monoplane design, consisting of a tractor propeller with wire-stayed
wings, the pilot being in an enclosed fuselage containing the engine in
front and carrying at its rear extremity fixed horizontal and vertical
surfaces combined with movable elevators and rudder. Constructionally,
the R.E.P. monoplane was of extreme interest as the body was constructed
of steel. The Antoinette monoplane, so ably flown by Latham, was another
very famous machine of the 1909-1910 period, though its performance were
frequently marred by engine failure; which was indeed the bugbear of all
these early experimenters, and it is difficult to say, after this lapse
of time, how far in many cases the failures which occurred, both in
performances and even in the actual ability to rise from the ground,
were due to defects in design or merely faults in the primitive engines
available. The Antoinette aroused admiration chiefly through its
graceful, birdlike lines, which have probably never been equalled; but
its chief interest for our present purpose lies in the novel method of
wing-staying which was employed. Contemporary monoplanes practically
all had their wings stayed by wires to a post in the centre above the
fuselage, and, usually, to the undercarriage below. In the Antoinette,
however, a king post was introduced half-way along the wing, from which
wires were carried to the ends of the wings and the body. This
was intended to give increased strength and permitted of a greater
wing-spread and consequently improved aspect ratio. The same system of
construction was adopted in the British Martinsyde monoplanes of two or
three years later.

This period also saw the production of the first triplane, which was
built by A. V. Roe in England and was fitted with a J.A.P. engine of
only 9 horse-power--an amazing performance which remains to this day
unequalled. Mr Roe's triplane was chiefly interesting otherwise for
the method of maintaining longitudinal control, which was achieved
by pivoting the whole of the three main planes so that their angle
of incidence could be altered. This was the direct converse of the
universal practice of elevating by means of a subsidiary surface either
in front or rear of the main planes.

Recollection of the various flying meetings and exhibitions which one
attended during the years from 1909 to 1911, or even 1912 are chiefly
notable for the fact that the first thought on seeing any new type of
machine was not as to what its 'performance'--in speed, lift, or what
not--would be; but speculation as to whether it would leave the ground
at all when eventually tried. This is perhaps the best indication of the
outstanding characteristic of that interim period between the time of
the first actual flights and the later period, commencing about 1912,
when ideas had become settled and it was at last becoming possible to
forecast on the drawing-board the performance of the completed machine
in the air. Without going into details, for which there is no space
here, it is difficult to convey the correct impression of the chaotic
state which existed as to even the elementary principles of aeroplane
design. All the exhibitions contained large numbers--one had almost
written a majority--of machines which embodied the most unusual features
and which never could, and in practice never did, leave the ground.
At the same time, there were few who were sufficiently hardy to say
certainly that this or that innovation was wrong; and consequently
dozens of inventors in every country were conducting isolated
experiments on both good and bad lines. All kinds of devices, mechanical
and otherwise, were claimed as the solution of the problem of stability,
and there was even controversy as to whether any measure of stability
was not undesirable; one school maintaining that the only safety lay
in the pilot having the sole say in the attitude of the machine at any
given moment, and fearing danger from the machine having any mind of
its own, so to speak. There was, as in most controversies, some right
on both sides, and when we come to consider the more settled period from
1912 to the outbreak of the War in 1914 we shall find how a compromise
was gradually effected.

At the same time, however, though it was at the time difficult to pick
out, there was very real progress being made, and, though a number of
'freak' machines fell out by the wayside, the pioneer designers of those
days learnt by a process of trial and error the right principles to
follow and gradually succeeded in getting their ideas crystallised.

In connection with stability mention must be made of a machine which
was evolved in the utmost secrecy by Mr J. W. Dunne in a remote part
of Scotland under subsidy from the War office. This type, which was
constructed in both monoplane and biplane form, showed that it was
in fact possible in 1910 and 1911 to design an aeroplane which could
definitely be left to fly itself in the air. One of the Dunne machines
was, for example flown from Farnborough to Salisbury Plain without any
control other than the rudder being touched; and on another occasion it
flew a complete circle with all controls locked automatically assuming
the correct bank for the radius of turn. The peculiar form of wing used,
the camber of which varied from the root to the tip, gave rise however,
to a certain loss in efficiency, and there was also a difficulty in the
pilot assuming adequate control when desired. Other machines designed to
be stable--such as the German Etrich and the British Weiss gliders and
Handley-Page monoplanes--were based on the analogy of a wing attached
to a certain seed found in Nature (the 'Zanonia' leaf), on the righting
effect of back-sloped wings combined with upturned (or 'negative') tips.
Generally speaking, however, the machines of the 1909-1912 period relied
for what automatic stability they had on the principle of the dihedral
angle, or flat V, both longitudinally and laterally. Longitudinally this
was obtained by setting the tail at a slightly smaller angle than the
main planes.

The question of reducing the resistance by adopting 'stream-line' forms,
along which the air could flow uninterruptedly without the formation
of eddies, was not at first properly realised, though credit should be
given to Edouard Nieuport, who in 1909 produced a monoplane with a
very large body which almost completely enclosed the pilot and made the
machine very fast, for those days, with low horse-power. On one of these
machines C. T. Weyman won the Gordon-Bennett Cup for America in 1911
and another put up a fine performance in the same race with only a 30
horse-power engine. The subject, was however, early taken up by the
British Advisory Committee for Aeronautics, which was established by
the Government in 1909, and designers began to realise the importance
of streamline struts and fuselages towards the end of this transition
period. These efforts were at first not always successful and showed at
times a lack of understanding of the problems involved, but there was
a very marked improvement during the year 1912. At the Paris Aero Salon
held early in that year there was a notable variety of ideas on the
subject; whereas by the time of the one held in October designs had
considerably settled down, more than one exhibitor showing what were
called 'monocoque' fuselages completely circular in shape and having
very low resistance, while the same show saw the introduction of
rotating cowls over the propeller bosses, or 'spinners,' as they came to
be called during the War. A particularly fine example of stream-lining
was to be found in the Deperdussin monoplane on which Vedrines won
back the Gordon-Bennett Aviation Cup from America at a speed of 105.5
m.p.h.--a considerable improvement on the 78 m.p.h. of the preceding
year, which was by no means accounted for by the mere increase in engine
power from 100 horse-power to 140 horse-power. This machine was the
first in which the refinement of 'stream-lining' the pilot's head, which
became a feature of subsequent racing machines, was introduced. This
consisted of a circular padded excresence above the cockpit immediately
behind the pilot's head, which gradually tapered off into the top
surface of the fuselage. The object was to give the air an uninterrupted
flow instead of allowing it to be broken up into eddies behind the
head of the pilot, and it also provided a support against the enormous
wind-pressure encountered. This true stream-line form of fuselage owed
its introduction to the Paulhan-Tatin 'Torpille' monoplane of the Paris
Salon of early 1917. Altogether the end of the year 1912 began to see
the disappearance of 'freak' machines with all sorts of original ideas
for the increase of stability and performance. Designs had by then
gradually become to a considerable extent standardised, and it had
become unusual to find a machine built which would fail to fly. The
Gnome engine held the field owing to its advantages, as the first of
the rotary type, in lightness and ease of fitting into the nose of a
fuselage. The majority of machines were tractors (propeller in front)
although a preference, which died down subsequently, was still shown for
the monoplane over the biplane. This year also saw a great increase
in the number of seaplanes, although the 'flying boat' type had only
appeared at intervals and the vast majority were of the ordinary
aeroplane type fitted with floats in place of the land undercarriage;
which type was at that time commonly called 'hydro-aeroplane.' The usual
horse power was 50--that of the smallest Gnome engine--although engines
of 100 to 140 horse-power were also fitted occasionally. The average
weight per horse-power varied from 18 to 25 lbs., while the wing-loading
was usually in the neighbourhood of 5 to 6 lbs. per square foot. The
average speed ranged from 65-75 miles per hour.




III. PROGRESS ON STANDARDISED LINES

In the last section an attempt has been made to show how, during what
was from the design standpoint perhaps the most critical period, order
gradually became evident out of chaos, ill-considered ideas dropped out
through failure to make good, and, though there was still plenty of room
for improvement in details, the bulk of the aeroplanes showed a general
similarity in form and conception. There was still a great deal to be
learnt in finding the best form of wing section, and performances were
still low; but it had become definitely possible to say that flying had
emerged from the chrysalis stage and had become a science. The period
which now began was one of scientific development and improvement--in
performance, manoeuvrability, and general airworthiness and stability.

The British Military Aeroplane Competition held in the summer of 1912
had done much to show the requirements in design by giving possibly
the first opportunity for a definite comparison of the performance
of different machines as measured by impartial observers on standard
lines--albeit the methods of measuring were crude. These showed that a
high speed--for those days--of 75 miles an hour or so was attended by
disadvantages in the form of an equally fast low speed, of 50 miles per
hour or more, and generally may be said to have given designers an idea
what to aim for and in what direction improvements were required. In
fact, the most noticeable point perhaps of the machines of this time was
the marked manner in which a machine that was good in one respect
would be found to be wanting in others. It had not yet been possible
to combine several desirable attributes in one machine. The nearest
approach to this was perhaps to be found in the much discussed
Government B.E.2 machine, which was produced from the Royal Aircraft
Factory at Farnborough, in the summer of 1912. Though considerably
criticized from many points of view it was perhaps the nearest approach
to a machine of all-round efficiency that had up to that date appeared.
The climbing rate, which subsequently proved so important for military
purposes, was still low, seldom, if ever, exceeding 400 feet per minute;
while gliding angles (ratio of descent to forward travel over the ground
with engine stopped) little exceeded 1 in 8.

The year 1912 and 1913 saw the subsequently all-conquering tractor
biplane begin to come into its own. This type, which probably originated
in England, and at any rate attained to its greatest excellence prior to
the War from the drawing offices of the Avro Bristol and Sopwith firms,
dealt a blow at the monoplane from which the latter never recovered.

The two-seater tractor biplane produced by Sopwith and piloted by H. G.
Hawker, showed that it was possible to produce a biplane with at least
equal speed to the best monoplanes, whilst having the advantage of
greater strength and lower landing speeds. The Sopwith machine had a top
speed of over 80 miles an hour while landing as slowly as little more
than 30 miles an hour; and also proved that it was possible to carry 3
passengers with fuel for 4 hours' flight with a motive power of only 80
horse-power. This increase in efficiency was due to careful attention to
detail in every part, improved wing sections, clean fuselage-lines, and
simplified undercarriages. At the same time, in the early part of 1913
a tendency manifested itself towards the four-wheeled undercarriage,
a pair of smaller wheels being added in front of the main wheels to
prevent overturning while running on the ground; and several designs of
oleo-pneumatic and steel-spring undercarriages were produced in place
of the rubber shock-absorber type which had up till then been almost
universal.

These two statements as to undercarriage designs may appear to be
contradictory, but in reality they do not conflict as they both showed
a greater attention to the importance of good springing, combined with
a desire to avoid complication and a mass of struts and wires which
increased head resistance.

The Olympia Aero Show of March, 1913, also produced a machine which,
although the type was not destined to prove the best for the purpose for
which it was designed, was of interest as being the first to be designed
specially for war purposes. This was the Vickers 'Gun-bus,' a 'pusher'
machine, with the propeller revolving behind the main planes between the
outriggers carrying the tail, with a seat right in front for a gunner
who was provided with a machine gun on a swivelling mount which had a
free field of fire in every direction forward. The device which proved
the death-blow for this type of aircraft during the war will be dealt
with in the appropriate place later, but the machine should not go
unrecorded.

As a result of a number of accidents to monoplanes the Government
appointed a Committee at the end of 1912 to inquire into the causes of
these. The report which was presented in March, 1913, exonerated the
monoplane by coming to the conclusion that the accidents were not caused
by conditions peculiar to monoplanes, but pointed out certain
desiderata in aeroplane design generally which are worth recording. They
recommended that the wings of aeroplanes should be so internally braced
as to have sufficient strength in themselves not to collapse if the
external bracing wires should give way. The practice, more common in
monoplanes than biplanes, of carrying important bracing wires from
the wings to the undercarriage was condemned owing to the liability of
damage from frequent landings. They also pointed out the desirability of
duplicating all main wires and their attachments, and of using stranded
cable for control wires. Owing to the suspicion that one accident at
least had been caused through the tearing of the fabric away from the
wing, it was recommended that fabric should be more securely fastened to
the ribs of the wings, and that devices for preventing the spreading of
tears should be considered. In the last connection it is interesting to
note that the French Deperdussin firm produced a fabric wing-covering
with extra strong threads run at right-angles through the fabric at
intervals in order to limit the tearing to a defined area.

In spite, however, of the whitewashing of the monoplane by the
Government Committee just mentioned, considerable stir was occasioned
later in the year by the decision of the War office not to order any
more monoplanes; and from this time forward until the War period the
British Army was provided exclusively with biplanes. Even prior to this
the popularity of the monoplane had begun to wane. At the Olympia
Aero Show in March, 1913, biplanes for the first time outnumbered the
'single-deckers'(as the Germans call monoplanes); which had the effect
of reducing the wing-loading. In the case of the biplanes exhibited
this averaged about 4 1/2 lbs. per square foot, while in the case of
the monoplanes in the same exhibition the lowest was 5 1/2 lbs., and
the highest over 8 1/2 lbs. per square foot of area. It may here be
mentioned that it was not until the War period that the importance
of loading per horse-power was recognised as the true criterion of
aeroplane efficiency, far greater interest being displayed in the amount
of weight borne per unit area of wing.

An idea of the state of development arrived at about this time may be
gained from the fact that the Commandant of the Military Wing of the
Royal Flying Corps in a lecture before the Royal Aeronautical Society
read in February, 1913, asked for single-seater scout aeroplanes with
a speed of 90 miles an hour and a landing speed of 45 miles an hour--a
performance which even two years later would have been considered modest
in the extreme. It serves to show that, although higher performances
were put up by individual machines on occasion, the general development
had not yet reached the stage when such performances could be obtained
in machines suitable for military purposes. So far as seaplanes were
concerned, up to the beginning of 1913 little attempt had been made to
study the novel problems involved, and the bulk of the machines at the
Monaco Meeting in April, 1913, for instance, consisted of land machines
fitted with floats, in many cases of a most primitive nature, without
other alterations. Most of those which succeeded in leaving the water
did so through sheer pull of engine power; while practically all were
incapable of getting off except in a fair sea, which enabled the pilot
to jump the machine into the air across the trough between two waves.
Stability problems had not yet been considered, and in only one or two
cases was fin area added at the rear high up, to counterbalance the
effect of the floats low down in front. Both twin and single-float
machines were used, while the flying boat was only just beginning
to come into being from the workshops of Sopwith in Great Britain,
Borel-Denhaut in France, and Curtiss in America. In view of the
approaching importance of amphibious seaplanes, mention should be made
of the flying boat (or 'bat boat' as it was called, following
Rudyard Kipling) which was built by Sopwith in 1913 with a wheeled
landing-carriage which could be wound up above the bottom surface of the
boat so as to be out of the way when alighting on water.

During 1913 the (at one time almost universal) practice originated by
the Wright Brothers, of warping the wings for lateral stability, began
to die out and the bulk of aeroplanes began to be fitted with flaps
(or 'ailerons') instead. This was a distinct change for the better, as
continually warping the wings by bending down the extremities of the
rear spars was bound in time to produce 'fatigue' in that member and
lead to breakage; and the practice became completely obsolete during the
next two or three years.

The Gordon-Bennett race of September, 1913, was again won by a
Deperdussin machine, somewhat similar to that of the previous year, but
with exceedingly small wings, only 107 square feet in area. The shape
of these wings was instructive as showing how what, from the general
utility point of view, may be disadvantageous can, for a special
purpose, be turned to account. With a span of 21 feet, the chord was
5 feet, giving the inefficient 'aspect ratio' of slightly over 4 to
1 only. The object of this was to reduce the lift, and therefore the
resistance, to as low a point as possible. The total weight was 1,500
lbs., giving a wing-loading of 14 lbs. per square foot--a hitherto
undreamt-of figure. The result was that the machine took an enormously
long run before starting; and after touching the ground on landing ran
for nearly a mile before stopping; but she beat all records by attaining
a speed of 126 miles per hour. Where this performance is mainly
interesting is in contrast to the machines of 1920, which with an even
higher speed capacity would yet be able to land at not more than 40 or
50 miles per hour, and would be thoroughly efficient flying machines.

The Rheims Aviation Meeting, at which the Gordon-Bennett race was flown,
also saw the first appearance of the Morane 'Parasol' monoplane. The
Morane monoplane had been for some time an interesting machine as being
the only type which had no fixed surface in rear to give automatic
stability, the movable elevator being balanced through being hinged
about one-third of the way back from the front edge. This made the
machine difficult to fly except in the hands of experts, but it was
very quick and handy on the controls and therefore useful for racing
purposes. In the 'Parasol' the modification was introduced of raising
the wing above the body, the pilot looking out beneath it, in order to
give as good a view as possible.

Before passing to the year 1914 mention should be made of the feat
performed by Nesteroff, a Russian, and Pegoud, a French pilot, who were
the first to demonstrate the possibilities of flying upside-down and
looping the loop. Though perhaps not coming strictly within the purview
of a chapter on design (though certain alterations were made to the top
wing-bracing of the machine for this purpose) this performance was
of extreme importance to the development of aviation by showing the
possibility of recovering, given reasonable height, from any position in
the air; which led designers to consider the extra stresses to which an
aeroplane might be subjected and to take steps to provide for them by
increasing strength where necessary.

When the year 1914 opened a speed of 126 miles per hour had been
attained and a height of 19,600 feet had been reached. The Sopwith and
Avro (the forerunner of the famous training machine of the War period)
were probably the two leading tractor biplanes of the world, both
two-seaters with a speed variation from 40 miles per hour up to some
90 miles per hour with 80 horse-power engines. The French were still
pinning their faith mainly to monoplanes, while the Germans were
beginning to come into prominence with both monoplanes and biplanes of
the 'Taube' type. These had wings swept backward and also upturned
at the wing-tips which, though it gave a certain measure of automatic
stability, rendered the machine somewhat clumsy in the air, and their
performances were not on the whole as high as those of either France or
Great Britain.

Early in 1914 it became known that the experimental work of Edward
Busk--who was so lamentably killed during an experimental flight later
in the year--following upon the researches of Bairstow and others had
resulted in the production at the Royal Aircraft Factory at Farnborough
of a truly automatically stable aeroplane. This was the 'R.E.'
(Reconnaissance Experimental), a development of the B.E. which has
already been referred to. The remarkable feature of this design was that
there was no particular device to which one could point out as the cause
of the stability. The stable result was attained simply by detailed
design of each part of the aeroplane, with due regard to its relation
to, and effect on, other parts in the air. Weights and areas were so
nicely arranged that under practically any conditions the machine tended
to right itself. It did not, therefore, claim to be a machine which it
was impossible to upset, but one which if left to itself would tend
to right itself from whatever direction a gust might come. When the
principles were extended to the 'B.E. 2c' type (largely used at the
outbreak of the War) the latter machine, if the engine were switched of
f at a height of not less than 1,000 feet above the ground, would after
a few moments assume its correct gliding angle and glide down to the
ground.

The Paris Aero Salon of December, 1913, had been remarkable chiefly for
the large number of machines of which the chassis and bodywork had been
constructed of steel-tubing; for the excess of monoplanes over biplanes;
and (in the latter) predominance of 'pusher' machines (with propeller
in rear of the main planes) compared with the growing British preference
for 'tractors' (with air screw in front). Incidentally, the Maurice
Farman, the last relic of the old type box-kite with elevator in front
appeared shorn of this prefix, and became known as the 'short-horn' in
contradistinction to its front-elevatored predecessor which, owing to
its general reliability and easy flying capabilities, had long been
affectionately called the 'mechanical cow.' The 1913 Salon also saw
some lingering attempts at attaining automatic stability by pendulum and
other freak devices.

Apart from the appearance of 'R.E.1,' perhaps the most notable
development towards the end of 1913 was the appearance of the Sopwith
'Tabloid 'tractor biplane. This single-seater machine, evolved from
the two-seater previously referred to, fitted with a Gnome engine of 80
horse-power, had the, for those days, remarkable speed of 92 miles an
hour; while a still more notable feature was that it could remain in
level flight at not more than 37 miles per hour. This machine is of
particular importance because it was the prototype and forerunner of the
successive designs of single-seater scout fighting machines which were
used so extensively from 1914 to 1918. It was also probably the first
machine to be capable of reaching a height of 1,000 feet within one
minute. It was closely followed by the 'Bristol Bullet,' which was
exhibited at the Olympia Aero Show of March, 1914. This last pre-war
show was mainly remarkable for the good workmanship displayed--rather
than for any distinct advance in design. In fact, there was a notable
diversity in the types displayed, but in detailed design considerable
improvements were to be seen, such as the general adoption of stranded
steel cable in place of piano wire for the mail bracing.




IV. THE WAR PERIOD

Up to this point an attempt has been made to give some idea of the
progress that was made during the eleven years that had elapsed since
the days of the Wrights' first flights. Much advance had been made and
aeroplanes had settled down, superficially at any rate, into more or
less standardised forms in three main types--tractor monoplanes, tractor
biplanes, and pusher biplanes. Through the application of the results
of experiments with models in wind tunnels to full-scale machines,
considerable improvements had been made in the design of wing sections,
which had greatly increased the efficiency of aeroplanes by raising the
amount of 'lift' obtained from the wing compared with the 'drag' (or
resistance to forward motion) which the same wing would cause. In the
same way the shape of bodies, interplane struts, etc., had been
improved to be of better stream-line shape, for the further reduction
of resistance; while the problems of stability were beginning to be
tolerably well understood. Records (for what they are worth) stood
at 21,000 feet as far as height was concerned, 126 miles per hour for
speed, and 24 hours duration. That there was considerable room for
development is, however, evidenced by a statement made by the late B.
C. Hucks (the famous pilot) in the course of an address delivered before
the Royal Aeronautical Society in July, 1914. 'I consider,' he said,
'that the present day standard of flying is due far more to the
improvement in piloting than to the improvement in machines.... I
consider those (early 1914) machines are only slight improvements on
the machines of three years ago, and yet they are put through evolutions
which, at that time, were not even dreamed of. I can take a good example
of the way improvement in piloting has outdistanced improvement in
machines--in the case of myself, my 'looping' Bleriot. Most of you know
that there is very little difference between that machine and the 50
horse-power Bleriot of three years ago.' This statement was, of course,
to some extent an exaggeration and was by no means agreed with by
designers, but there was at the same time a germ of truth in it. There
is at any rate little doubt that the theory and practice of aeroplane
design made far greater strides towards becoming an exact science during
the four years of War than it had done during the six or seven years
preceding it.

It is impossible in the space at disposal to treat of this development
even with the meagre amount of detail that has been possible while
covering the 'settling down' period from 1911 to 1914, and it is
proposed, therefore, to indicate the improvements by sketching briefly
the more noticeable difference in various respects between the average
machine of 1914 and a similar machine of 1918.

In the first place, it was soon found that it was possible to obtain
greater efficiency and, in particular, higher speeds, from tractor
machines than from pusher machines with the air screw behind the main
planes. This was for a variety of reasons connected with the efficiency
of propellers and the possibility of reducing resistance to a greater
extent in tractor machines by using a 'stream-line' fuselage (or body)
to connect the main planes with the tail. Full advantage of this could
not be taken, however, owing to the difficulty of fixing a machine-gun
in a forward direction owing to the presence of the propeller. This was
finally overcome by an ingenious device (known as an 'Interrupter gear')
which allowed the gun to fire only when none of the propeller blades
was passing in front of the muzzle. The monoplane gradually fell into
desuetude, mainly owing to the difficulty of making that type adequately
strong without it becoming prohibitively heavy, and also because of its
high landing speed and general lack of manoeuvrability. The triplane
was also little used except in one or two instances, and, practically
speaking, every machine was of the biplane tractor type.

A careful consideration of the salient features leading to maximum
efficiency in aeroplanes--particularly in regard to speed and climb,
which were the two most important military requirements--showed that
a vital feature was the reduction in the amount of weight lifted per
horse-power employed; which in 1914 averaged from 20 to 25 lbs. This was
effected both by gradual increase in the power and size of the engines
used and by great improvement in their detailed design (by increasing
compression ratio and saving weight whenever possible); with the result
that the motive power of single-seater aeroplanes rose from 80 and 100
horse-power in 1914 to an average of 200 to 300 horse-power, while the
actual weight of the engine fell from 3 1/2-4 lbs. per horse-power to an
average of 2 1/2 lbs. per horse-power. This meant that while a pre-war
engine of 100 horse-power would weigh some 400 lbs., the 1918 engine
developing three times the power would have less than double the weight.
The result of this improvement was that a scout aeroplane at the time
of the Armistice would have 1 horse-power for every 8 lbs. of weight
lifted, compared with the 20 or 25 lbs. of its 1914 predecessors. This
produced a considerable increase in the rate of climb, a good postwar
machine being able to reach 10,000 feet in about 5 minutes and 20,000
feet in under half an hour. The loading per square foot was also
considerably increased; this being rendered possible both by improvement
in the design of wing sections and by more scientific construction
giving increased strength. It will be remembered that in the machine
of the very early period each square foot of surface had only to lift
a weight of some 1 1/2 to 2 lbs., which by 1914 had been increased to
about 4 lbs. By 1918 aeroplanes habitually had a loading of 8 lbs. or
more per square foot of area; which resulted in great increase in speed.
Although a speed of 126 miles per hour had been attained by a specially
designed racing machine over a short distance in 1914, the average at
that period little exceeded, if at all, 100 miles per hour; whereas in
1918 speeds of 130 miles per hour had become a commonplace, and shortly
afterwards a speed of over 166 miles an hour was achieved.

In another direction, also, that of size, great developments were made.
Before the War a few machines fitted with more than one engine had been
built (the first being a triple Gnome-engined biplane built by Messrs
Short Bros. at Eastchurch in 1913), but none of large size had been
successfully produced, the total weight probably in no case exceeding
about 2 tons. In 1916, however, the twin engine Handley-Page biplane
was produced, to be followed by others both in this country and abroad,
which represented a very great increase in size and, consequently,
load-carrying capacity. By the end of the War period several types were
in existence weighing a total of 10 tons when fully loaded, of which
some 4 tons or more represented 'useful load' available for crew,
fuel, and bombs or passengers. This was attained through very careful
attention to detailed design, which showed that the material could be
employed more efficiently as size increased, and was also due to the
fact that a large machine was not liable to be put through the same
evolutions as a small machine, and therefore could safely be built with
a lower factor of safety. Owing to the fact that a wing section which is
adopted for carrying heavy loads usually has also a somewhat low lift
to drag ratio, and is not therefore productive of high speed, these
machines are not as fast as light scouts; but, nevertheless, they proved
themselves capable of achieving speeds of 100 miles an hour or more in
some cases; which was faster than the average small machine of 1914.

In one respect the development during the War may perhaps have proved
to be somewhat disappointing, as it might have been expected that great
improvements would be effected in metal construction, leading almost to
the abolition of wooden structures. Although, however, a good deal of
experimental work was done which resulted in overcoming at any rate the
worst of the difficulties, metal-built machines were little used (except
to a certain extent in Germany) chiefly on account of the need for rapid
production and the danger of delay resulting from switching over from
known and tried methods to experimental types of construction.
The Germans constructed some large machines, such as the giant
Siemens-Schukhert machine, entirely of metal except for the wing
covering, while the Fokker and Junker firms about the time of the
Armistice in 1918 both produced monoplanes with very deep all-metal
wings (including the covering) which were entirely unstayed externally,
depending for their strength on internal bracing. In Great Britain cable
bracing gave place to a great extent to 'stream-line wires,' which are
steel rods rolled to a more or less oval section, while tie-rods were
also extensively used for the internal bracing of the wings. Great
developments in the economical use of material were also made in the
direction of using built-up main spars for the wings and interplane
struts; spars composed of a series of layers (or 'laminations') of
different pieces of wood also being used.

Apart from the metallic construction of aeroplanes an enormous amount
of work was done in the testing of different steels and light alloys for
use in engines, and by the end of the War period a number of aircraft
engines were in use of which the pistons and other parts were of such
alloys; the chief difficulty having been not so much in the design as in
the successful heat-treatment and casting of the metal.

An important development in connection with the inspection and
testing of aircraft parts, particularly in the case of metal, was the
experimental application of X-ray photography, which showed up latent
defects, both in the material and in manufacture, which would otherwise
have passed unnoticed. This method was also used to test the penetration
of glue into the wood on each side of joints, so giving a measure of the
strength; and for the effect of 'doping' the wings, dope being a film
(of cellulose acetate dissolved in acetone with other chemicals)
applied to the covering of wings and bodies to render the linen taut and
weatherproof, besides giving it a smooth surface for the lessening of
'skin friction' when passing rapidly through the air.

An important result of this experimental work was that it in many cases
enabled designers to produce aeroplane parts from less costly material
than had previously been considered necessary, without impairing the
strength. It may be mentioned that it was found undesirable to use
welded joints on aircraft in any part where the material is subjectto
a tensile or bending load, owing to the danger resulting from bad
workmanship causing the material to become brittle--an effect which
cannot be discovered except by cutting through the weld, which, of
course, involves a test to destruction. Written, as it has been, in
August, 1920, it is impossible in this chapter to give any conception of
how the developments of War will be applied to commercial aeroplanes,
as few truly commercial machines have yet been designed, and even those
still show distinct traces of the survival of war mentality. When,
however, the inevitable recasting of ideas arrives, it will become
evident, whatever the apparent modification in the relative importance
of different aspects of design, that enormous advances were made under
the impetus of War which have left an indelible mark on progress.

We have, during the seventeen years since aeroplanes first took the air,
seen them grow from tentative experimental structures of unknown and
unknowable performance to highly scientific products, of which not
only the performances (in speed, load-carrying capacity, and climb) are
known, but of which the precise strength and degree of stability can be
forecast with some accuracy on the drawing board. For the rest, with
the future lies--apart from some revolutionary change in fundamental
design--the steady development of a now well-tried and well-found
engineering structure.




PART III. AEROSTATICS




I. BEGINNINGS

Francesco Lana, with his 'aerial ship,' stands as one of the first great
exponents of aerostatics; up to the time of the Montgolfier and
Charles balloon experiments, aerostatic and aerodynamic research are so
inextricably intermingled that it has been thought well to treat of them
as one, and thus the work of Lana, Veranzio and his parachute, Guzman's
frauds, and the like, have already been sketched. In connection with
Guzman, Hildebrandt states in his Airships Past and Present, a
fairly exhaustive treatise on the subject up to 1906, the year of its
publication, that there were two inventors--or charlatans--Lorenzo de
Guzman and a monk Bartolemeo Laurenzo, the former of whom constructed
an unsuccessful airship out of a wooden basket covered with paper,
while the latter made certain experiments with a machine of which no
description remains. A third de Guzman, some twenty-five years later,
announced that he had constructed a flying machine, with which he
proposed to fly from a tower to prove his success to the public. The
lack of record of any fatal accident overtaking him about that time
seems to show that the experiment was not carried out.

Galien, a French monk, published a book L'art de naviguer dans l'air
in 1757, in which it was conjectured that the air at high levels was
lighter than that immediately over the surface of the earth. Galien
proposed to bring down the upper layers of air and with them fill a
vessel, which by Archimidean principle would rise through the heavier
atmosphere. If one went high enough, said Galien, the air would be two
thousand times as light as water, and it would be possible to construct
an airship, with this light air as lifting factor, which should be as
large as the town of Avignon, and carry four million passengers with
their baggage. How this high air was to be obtained is matter for
conjecture--Galien seems to have thought in a vicious circle, in which
the vessel that must rise to obtain the light air must first be filled
with it in order to rise.

Cavendish's discovery of hydrogen in 1776 set men thinking, and soon a
certain Doctor Black was suggesting that vessels might be filled with
hydrogen, in order that they might rise in the air. Black, however, did
not get beyond suggestion; it was Leo Cavallo who first made experiments
with hydrogen, beginning with filling soap bubbles, and passing on to
bladders and special paper bags. In these latter the gas escaped,
and Cavallo was about to try goldbeaters' skin at the time that the
Montgolfiers came into the field with their hot air balloon.

Joseph and Stephen Montgolfier, sons of a wealthy French paper
manufacturer, carried out many experiments in physics, and Joseph
interested himself in the study of aeronautics some time before the
first balloon was constructed by the brothers--he is said to have made
a parachute descent from the roof of his house as early as 1771, but
of this there is no proof. Galien's idea, together with study of the
movement of clouds, gave Joseph some hope of achieving aerostation
through Galien's schemes, and the first experiments were made by passing
steam into a receiver, which, of course, tended to rise--but the
rapid condensation of the steam prevented the receiver from more than
threatening ascent. The experiments were continued with smoke, which
produced only a slightly better effect, and, moreover, the paper bag
into which the smoke was induced permitted of escape through its pores;
finding this method a failure the brothers desisted until Priestley's
work became known to them, and they conceived the use of hydrogen as
a lifting factor. Trying this with paper bags, they found that the
hydrogen escaped through the pores of the paper.

Their first balloon, made of paper, reverted to the hot-air principle;
they lighted a fire of wool and wet straw under the balloon--and as a
matter of course the balloon took fire after very little experiment;
thereupon they constructed a second, having a capacity of 700 cubic
feet, and this rose to a height of over 1,000 feet. Such a success gave
them confidence, and they gave their first public exhibition on June
5th, 1783, with a balloon constructed of paper and of a circumference of
112 feet. A fire was lighted under this balloon, which, after rising to
a height of 1,000 feet, descended through the cooling of the air inside
a matter of ten minutes. At this the Academie des Sciences invited the
brothers to conduct experiments in Paris.

The Montgolfiers were undoubtedly first to send up balloons, but other
experimenters were not far behind them, and before they could get to
Paris in response to their invitation, Charles, a prominent physicist of
those days, had constructed a balloon of silk, which he proofed against
escape of gas with rubber--the Roberts had just succeeded in dissolving
this substance to permit of making a suitable coating for the silk. With
a quarter of a ton of sulphuric acid, and half a ton of iron filings
and turnings, sufficient hydrogen was generated in four days to fill
Charles's balloon, which went up on August 28th, 1783. Although the day
was wet, Paris turned out to the number of over 300,000 in the Champs de
Mars, and cannon were fired to announce the ascent of the balloon. This,
rising very rapidly, disappeared amid the rain clouds, but, probably
bursting through no outlet being provided to compensate for the
escape of gas, fell soon in the neighbourhood of Paris. Here peasants,
ascribing evil supernatural influence to the fall of such a thing from
nowhere, went at it with the implements of their craft--forks, hoes, and
the like--and maltreated it severely, finally attaching it to a horse's
tail and dragging it about until it was mere rag and scrap.

Meanwhile, Joseph Montgolfier, having come to Paris, set about the
construction of a balloon out of linen; this was in three diverse
sections, the top being a cone 30 feet in depth, the middle a cylinder
42 feet in diameter by 26 feet in depth, and the bottom another cone 20
feet in depth from junction with the cylindrical portion to its point.
The balloon was both lined and covered with paper, decorated in blue and
gold. Before ever an ascent could be attempted this ambitious balloon
was caught in a heavy rainstorm which reduced its paper covering to pulp
and tore the linen at its seams, so that a supervening strong wind tore
the whole thing to shreds.

Montgolfier's next balloon was spherical, having a capacity of 52,000
cubic feet. It was made from waterproofed linen, and on September 19th,
1783, it made an ascent for the palace courtyard at Versailles, taking
up as passengers a cock, a sheep, and a duck. A rent at the top of the
balloon caused it to descend within eight minutes, and the duck and
sheep were found none the worse for being the first living things to
leave the earth in a balloon, but the cock, evidently suffering, was
thought to have been affected by the rarefaction of the atmosphere at
the tremendous height reached--for at that time the general opinion was
that the atmosphere did not extend more than four or five miles above
the earth's surface. It transpired later that the sheep had trampled on
the cock, causing more solid injury than any that might be inflicted by
rarefied air in an eight-minute ascent and descent of a balloon.

For achieving this flight Joseph Montgolfier received from the King
of France a pension of of L40, while Stephen was given the order of St
Michael, and a patent of nobility was granted to their father. They were
made members of the Legion d'Honneur, and a scientific deputation,
of which Faujas de Saint-Fond, who had raised the funds with which
Charles's hydrogen balloon was constructed, presented to Stephen
Montgolfier a gold medal struck in honour of his aerial conquest.
Since Joseph appears to have had quite as much share in the success
as Stephen, the presentation of the medal to one brother only was in
questionable taste, unless it was intended to balance Joseph's pension.

Once aerostation had been proved possible, many people began the
construction of small balloons--the wholehole thing was regarded as a
matter of spectacles and a form of amusement by the great majority. A
certain Baron de Beaumanoir made the first balloon of goldbeaters' skin,
this being eighteen inches in diameter, and using hydrogen as a lifting
factor. Few people saw any possibilities in aerostation, in spite of
the adventures of the duck and sheep and cock; voyages to the moon were
talked and written, and there was more of levity than seriousness over
ballooning as a rule. The classic retort of Benjamin Franklin stands
as an exception to the general rule: asked what was the use of
ballooning--'What's the use of a baby?' he countered, and the spirit of
that reply brought both the dirigible and the aeroplane to being, later.

The next noteworthy balloon was one by Stephen Montgolfier, designed to
take up passengers, and therefore of rather large dimensions, as these
things went then. The capacity was 100,000 cubic feet, the depth being
85 feet, and the exterior was very gaily decorated. A short, cylindrical
opening was made at the lower extremity, and under this a fire-pan was
suspended, above the passenger car of the balloon. On October 15th,
1783, Pilatre de Rozier made the first balloon ascent--but the balloon
was held captive, and only allowed to rise to a height of 80 feet. But,
a little later in 1783, Rozier secured the honour of making the first
ascent in a free balloon, taking up with him the Marquis d'Arlandes.
It had been originally intended that two criminals, condemned to death,
should risk their lives in the perilous venture, with the prospect of
a free pardon if they made a safe descent, but d'Arlandes got the royal
consent to accompany Rozier, and the criminals lost their chance. Rozier
and d'Arlandes made a voyage lasting for twenty-five minutes, and, on
landing, the balloon collapsed with such rapidity as almost to suffocate
Rozier, who, however, was dragged out to safety by d'Arlandes. This
first aerostatic journey took place on November 21st, 1783.

Some seven months later, on June 4th, 1784, a Madame Thible ascended in
a free balloon, reaching a height of 9,000 feet, and making a journey
which lasted for forty-five minutes--the great King Gustavus of Sweden
witnessed this ascent. France grew used to balloon ascents in the course
of a few months, in spite of the brewing of such a storm as might
have been calculated to wipe out all but purely political interests.
Meanwhile, interest in the new discovery spread across the Channel,
and on September 15th, 1784, one Vincent Lunardi made the first balloon
voyage in England, starting from the Artillery Ground at Chelsea, with
a cat and dog as passengers, and landing in a field in the parish of
Standon, near Ware. There is a rather rare book which gives a very
detailed account of this first ascent in England, one copy of which
is in the library of the Royal Aeronautical Society; the venturesome
Lunardi won a greater measure of fame through his exploit than did
Cody for his infinitely more courageous and--from a scientific point of
view--valuable first aeroplane ascent in this country.

The Montgolfier type of balloon, depending on hot air for its lifting
power, was soon realised as having dangerous limitations. There was
always a possibility of the balloon catching fire while it was being
filled, and on landing there was further danger from the hot pan which
kept up the supply of hot air on the voyage--the collapsing balloon fell
on the pan, inevitably. The scientist Saussure, observing the filling of
the balloons very carefully, ascertained that it was rarefaction of the
air which was responsible for the lifting power, and not the heat in
itself, and, owing to the rarefaction of the air at normal temperature
at great heights above the earth, the limit of ascent for a balloon of
the Montgolfier type was estimated by him at under 9,000 feet. Moreover,
since the amount of fuel that could be carried for maintaining the
heat of the balloon after inflation was subject to definite limits,
prescribed by the carrying capacity of the balloon, the duration of the
journey was necessarily limited just as strictly.

These considerations tended to turn the minds of those interested
in aerostation to consideration of the hydrogen balloon evolved by
Professor Charles. Certain improvements had been made by Charles
since his first construction; he employed rubber-coated silk in the
construction of a balloon of 30 feet diameter, and provided a net for
distributing the pressure uniformly over the surface of the envelope;
this net covered the top half of the balloon, and from its lower edge
dependent ropes hung to join on a wooden ring, from which the car of
the balloon was suspended--apart from the extension of the net so as to
cover in the whole of the envelope, the spherical balloon of to-day is
virtually identical with that of Charles in its method of construction.
He introduced the valve at the top of the balloon, by which escape of
gas could be controlled, operating his valve by means of ropes which
depended to the car of the balloon, and he also inserted a tube, of
about 7 inches diameter, at the bottom of the balloon, not only for
purposes of inflation, but also to provide a means of escape for gas in
case of expansion due to atmospheric conditions.

Sulphuric acid and iron filings were used by Charles for filling his
balloon, which required three days and three nights for the generation
of its 14,000 cubic feet of hydrogen gas. The inflation was completed on
December 1st, 1783, and the fittings carried included a barometer and a
grapnel form of anchor. In addition to this, Charles provided the first
'ballon sonde' in the form of a small pilot balloon which he handed to
Montgolfier to launch before his own ascent, in order to determine the
direction and velocity of the wind. It was a graceful compliment to his
rival, and indicated that, although they were both working to the one
end, their rivalry was not a matter of bitterness.

Ascending on December 1st, 1783, Charles took with him one of the
brothers Robert, and with him made the record journey up to that date,
covering a period of three and three-quarter hours, in which time they
journeyed some forty miles. Robert then landed, and Charles ascended
again alone, reaching such a height as to feel the effects of the
rarefaction of the air, this very largely due to the rapidity of his
ascent. Opening the valve at the top of the balloon, he descended
thirty-five minutes after leaving Robert behind, and came to earth a few
miles from the point of the first descent. His discomfort over the rapid
ascent was mainly due to the fact that, when Robert landed, he forgot to
compensate for the reduction of weight by taking in further ballast,
but the ascent proved the value of the tube at the bottom of the balloon
envelope, for the gas escaped very rapidly in that second ascent, and,
but for the tube, the balloon must inevitably have burst in the air,
with fatal results for Charles.

As in the case of aeroplane flight, as soon as the balloon was proved
practicable the flight across the English Channel was talked of, and
Rozier, who had the honour of the first flight, announced his intention
of being first to cross. But Blanchard, who had an idea for a 'flying
car,' anticipated him, and made a start from Dover on January 7th, 1785,
taking with him an American doctor named Jeffries. Blanchard fitted out
his craft for the journey very thoroughly, taking provisions, oars, and
even wings, for propulsion in case of need. He took so much, in fact,
that as soon as the balloon lifted clear of the ground the whole of the
ballast had to be jettisoned, lest the balloon should drop into the sea.
Half-way across the Channel the sinking of the balloon warned Blanchard
that he had to part with more than ballast to accomplish the journey,
and all the equipment went, together with certain books and papers that
were on board the car. The balloon looked perilously like collapsing,
and both Blanchard and Jeffries began to undress in order further to
lighten their craft--Jeffries even proposed a heroic dive to save the
situation, but suddenly the balloon rose sufficiently to clear the
French coast, and the two voyagers landed at a point near Calais in
the Forest of Gaines, where a marble column was subsequently erected to
commemorate the great feat.

Rozier, although not first across, determined to be second, and for
that purpose he constructed a balloon which was to owe its buoyancy to
a combination of the hydrogen and hot air principles. There was a
spherical hydrogen balloon above, and beneath it a cylindrical container
which could be filled with hot air, thus compensating for the leakage of
gas from the hydrogen portion of the balloon--regulating the heat of
his fire, he thought, would give him perfect control in the matter of
ascending and descending.

On July 6th, 1785, a favourable breeze gave Rozier his opportunity of
starting from the French coast, and with a passenger aboard he cast off
in his balloon, which he had named the 'Aero-Montgolfiere.' There was a
rapid rise at first, and then for a time the balloon remained stationary
over the land, after which a cloud suddenly appeared round the balloon,
denoting that an explosion had taken place. Both Rozier and his
companion were killed in the fall, so that he, first to leave the earth
by balloon, was also first victim to the art of aerostation.

There followed, naturally, a lull in the enthusiasm with which
ballooning had been taken up, so far as France was concerned. In Italy,
however, Count Zambeccari took up hot-air ballooning, using a spirit
lamp to give him buoyancy, and on the first occasion when the balloon
car was set on fire Zambeccari let down his passenger by means of the
anchor rope, and managed to extinguish the fire while in the air. This
reduced the buoyancy of the balloon to such an extent that it fell
into the Adriatic and was totally wrecked, Zambeccari being rescued by
fishermen. He continued to experiment up to 1812, when he attempted to
ascend at Bologna; the spirit in his lamp was upset by the collision
of the car with a tree, and the car was again set on fire. Zambeccari
jumped from the car when it was over fifty feet above level ground, and
was killed. With him the Rozier type of balloon, combining the hydrogen
and hot air principles, disappeared; the combination was obviously too
dangerous to be practical.

The brothers Robert were first to note how the heat of the sun acted on
the gases within a balloon envelope, and it has since been ascertained
that sun rays will heat the gas in a balloon to as much as 80 degrees
Fahrenheit greater temperature than the surrounding atmosphere;
hydrogen, being less affected by change of temperature than coal gas, is
the most suitable filling element, and coal gas comes next as the medium
of buoyancy. This for the free and non-navigable balloon, though for the
airship, carrying means of combustion, and in military work liable to
ignition by explosives, the gas helium seems likely to replace hydrogen,
being non-combustible.

In spite of the development of the dirigible airship, there remains
work for the free, spherical type of balloon in the scientific field.
Blanchard's companion on the first Channel crossing by balloon, Dr
Jeffries, was the first balloonist to ascend for purely scientific
purposes; as early as 1784 he made an ascent to a height of 9,000 feet,
and observed a fall in temperature of from degrees--at the level of
London, where he began his ascent--to 29 degrees at the maximum
height reached. He took up an electrometer, a hydrometer, a compass, a
thermometer, and a Toricelli barometer, together with bottles of water,
in order to collect samples of the air at different heights. In 1785 he
made a second ascent, when trigonometrical observations of the height of
the balloon were made from the French coast, giving an altitude of 4,800
feet.

The matter was taken up on its scientific side very early in America,
experiments in Philadelphia being almost simultaneous with those of the
Montgolfiers in France. The flight of Rozier and d'Arlandes inspired two
members of the Philadelphia Philosophical Academy to construct a balloon
or series of balloons of their own design; they made a machine which
consisted of no less than 47 small hydrogen balloons attached to a
wicker car, and made certain preliminary trials, using animals as
passengers. This was followed by a captive ascent with a man as
passenger, and eventually by the first free ascent in America, which
was undertaken by one James Wilcox, a carpenter, on December 28th,
1783. Wilcox, fearful of falling into a river, attempted to regulate his
landing by cutting slits in some of the supporting balloons, which was
the method adopted for regulating ascent or descent in this machine.
He first cut three, and then, finding that the effect produced was not
sufficient, cut three more, and then another five--eleven out of the
forty-seven. The result was so swift a descent that he dislocated his
wrist on landing.

            A NOTE ON BALLONETS OR AIR BAGS.

Meusnier, toward the end of the eighteenth century, was first to
conceive the idea of compensating for the loss of gas due to expansion
by fitting to the interior of a free balloon a ballonet, or air bag,
which could be pumped full of air so as to retain the shape and rigidity
of the envelope.

The ballonet became particularly valuable as soon as airship
construction became general, and it was in the course of advance
in Astra Torres design that the project was introduced of using the
ballonets in order to give inclination from the horizontal. In the
earlier Astra Torres, trimming was accomplished by moving the car fore
and aft--this in itself was an advance on the separate 'sliding weigh'
principle--and this was the method followed in the Astra Torres bought
by the British Government from France in 1912 for training airship
pilots. Subsequently, the two ballonets fitted inside the envelope were
made to serve for trimming by the extent of their inflation, and this
method of securing inclination proved the best until exterior rudders,
and greater engine power, supplanted it, as in the Zeppelin and, in
fact, all rigid types.

In the kite balloon, the ballonet serves the purpose of a rudder,
filling itself through the opening being kept pointed toward the
wind--there is an ingenious type of air scoop with non-return valve
which assures perfect inflation. In the S.S. type of airship, two
ballonets are provided, the supply of air being taken from the propeller
draught by a slanting aluminium tube to the underside of the envelope,
where it meets a longitudinal fabric hose which connects the two
ballonet air inlets. In this hose the non-return air valves, known
as 'crab-pots,' are fitted, on either side of the junction with the
air-scoop. Two automatic air valves, one for each ballonet, are fitted
in the underside of the envelope, and, as the air pressure tends to
open these instead of keeping them shut, the spring of the valve is set
inside the envelope. Each spring is set to open at a pressure of 25 to
28 mm.




II. THE FIRST DIRIGIBLES

Having got off the earth, the very early balloonists set about the task
of finding a means of navigating the air but, lacking steam or other
accessory power to human muscle, they failed to solve the problem.
Joseph Montgolfier speedily exploded the idea of propelling a balloon
either by means of oars or sails, pointing out that even in a dead
calm a speed of five miles an hour would be the limit achieved. Still,
sailing balloons were constructed, even up to the time of Andree, the
explorer, who proposed to retard the speed of the balloon by ropes
dragging on the ground, and then to spread a sail which should catch
the wind and permit of deviation of the course. It has been proved that
slight divergences from the course of the wind can be obtained by this
means, but no real navigation of the air could be thus accomplished.

Professor Wellner, of Brunn, brought up the idea of a sailing balloon
in more practical fashion in 1883. He observed that surfaces inclined to
the horizontal have a slight lateral motion in rising and falling, and
deduced that by alternate lowering and raising of such surfaces he would
be able to navigate the air, regulating ascent and descent by increasing
or decreasing the temperature of his buoyant medium in the balloon. He
calculated that a balloon, 50 feet in diameter and 150 feet in length,
with a vertical surface in front and a horizontal surface behind, might
be navigated at a speed of ten miles per hour, and in actual tests at
Brunn he proved that a single rise and fall moved the balloon three
miles against the wind. His ideas were further developed by Lebaudy in
the construction of the early French dirigibles.

According to Hildebrandt,[*] the first sailing balloon was built in 1784
by Guyot, who made his balloon egg-shaped, with the smaller end at the
back and the longer axis horizontal; oars were intended to propel the
craft, and naturally it was a failure. Carra proposed the use of paddle
wheels, a step in the right direction, by mounting them on the sides
of the car, but the improvement was only slight. Guyton de Morveau,
entrusted by the Academy of Dijon with the building of a sailing
balloon, first used a vertical rudder at the rear end of his
construction--it survives in the modern dirigible. His construction
included sails and oars, but, lacking steam or other than human
propulsive power, the airship was a failure equally with Guyot's.

[*] Airships Past and Present.

Two priests, Miollan and Janinet, proposed to drive balloons through the
air by the forcible expulsion of the hot air in the envelope from the
rear of the balloon. An opening was made about half-way up the envelope,
through which the hot air was to escape, buoyancy being maintained by a
pan of combustibles in the car. Unfortunately, this development of the
Montgolfier type never got a trial, for those who were to be spectators
of the first flight grew exasperated at successive delays, and in the
end, thinking that the balloon would never rise, they destroyed it.

Meusnier, a French general, first conceived the idea of compensating
for loss of gas by carrying an air bag inside the balloon, in order
to maintain the full expansion of the envelope. The brothers Robert
constructed the first balloon in which this was tried and placed the
air bag near the neck of the balloon which was intended to be driven
by oars, and steered by a rudder. A violent swirl of wind which was
encountered on the first ascent tore away the oars and rudder and broke
the ropes which held the air bag in position; the bag fell into the
opening of the neck and stopped it up, preventing the escape of gas
under expansion. The Duc de Chartres, who was aboard, realised the
extreme danger of the envelope bursting as the balloon ascended, and at
16,000 feet he thrust a staff through the envelope--another account says
that he slit it with his sword--and thus prevented disaster. The descent
after this rip in the fabric was swift, but the passengers got off
without injury in the landing.

Meusnier, experimenting in various ways, experimented with regard to
the resistance offered by various shapes to the air, and found that an
elliptical shape was best; he proposed to make the car boat--shaped, in
order further to decrease the resistance, and he advocated an entirely
rigid connection between the car and the body of the balloon, as
indispensable to a dirigible.[*] He suggested using three propellers,
which were to be driven by hand by means of pulleys, and calculated that
a crew of eighty would be required to furnish sufficient motive power.
Horizontal fins were to be used to assure stability, and Meusnier
thoroughly investigated the pressures exerted by gases, in order to
ascertain the stresses to which the envelope would be subjected. More
important still, he went into detail with regard to the use of air bags,
in order to retain the shape of the balloon under varying pressures of
gas due to expansion and consequent losses; he proposed two separate
envelopes, the inner one containing gas, and the space between it and
the outer one being filled with air. Further, by compressing the air
inside the air bag, the rate of ascent or descent could be regulated.
Lebaudy, acting on this principle, found it possible to pump air at the
rate of 35 cubic feet per second, thus making good loss of ballast which
had to be thrown overboard.

[*] Hildebrandt.

Meusnier's balloon, of course, was never constructed, but his ideas have
been of value to aerostation up to the present time. His career ended
in the revolutionary army in 1793, when he was killed in the fighting
before Mayence, and the King of Prussia ordered all firing to cease
until Meusnier had been buried. No other genius came forward to carry
on his work, and it was realised that human muscle could not drive a
balloon with certainty through the air; experiment in this direction
was abandoned for nearly sixty years, until in 1852 Giffard brought the
first practicable power-driven dirigible to being.

Giffard, inventor of the steam injector, had already made balloon
ascents when he turned to aeronautical propulsion, and constructed a
steam engine of 5 horsepower with a weight of only 100 lbs.--a great
achievement for his day. Having got his engine, he set about making the
balloon which it was to drive; this he built with the aid of two other
enthusiasts, diverging from Meusnier's ideas by making the ends pointed,
and keeping the body narrowed from Meusnier's ellipse to a shape more
resembling a rather fat cigar. The length was 144 feet, and the greatest
diameter only 40 feet, while the capacity was 88,000 cubic feet. A net
which covered the envelope of the balloon supported a spar, 66 feet in
length, at the end of which a triangular sail was placed vertically to
act as rudder. The car, slung 20 feet below the spar, carried the engine
and propeller. Engine and boiler together weighed 350 lbs., and drove
the 11 foot propeller at 110 revolutions per minute.

As precaution against explosion, Giffard arranged wire gauze in front
of the stoke-hole of his boiler, and provided an exhaust pipe which
discharged the waste gases from the engine in a downward direction. With
this first dirigible he attained to a speed of between 6 and 8 feet per
second, thus proving that the propulsion of a balloon was a possibility,
now that steam had come to supplement human effort.

Three years later he built a second dirigible, reducing the diameter and
increasing the length of the gas envelope, with a view to reducing air
resistance. The length of this was 230 feet, the diameter only 33 feet,
and the capacity was 113,000 cubic feet, while the upper part of the
envelope, to which the covering net was attached, was specially covered
to ensure a stiffening effect. The car of this dirigible was dropped
rather lower than that of the first machine, in order to provide more
thoroughly against the danger of explosions. Giffard, with a companion
named Yon as passenger, took a trial trip on this vessel, and made a
journey against the wind, though slowly. In commencing to descend, the
nose of the envelope tilted upwards, and the weight of the car and
its contents caused the net to slip, so that just before the dirigible
reached the ground, the envelope burst. Both Giffard and his companion
escaped with very slight injuries.

Plans were immediately made for the construction of a third dirigible,
which was to be 1,970 feet in length, 98 feet in extreme diameter, and
to have a capacity of 7,800,000 cubic feet of gas. The engine of this
giant was to have weighed 30 tons, and with it Giffard expected to
attain a speed of 40 miles per hour. Cost prevented the scheme being
carried out, and Giffard went on designing small steam engines until his
invention of the steam injector gave him the funds to turn to dirigibles
again. He built a captive balloon for the great exhibition in London
in 1868, at a cost of nearly L30,000, and designed a dirigible balloon
which was to have held a million and three quarters cubic feet of gas,
carry two boilers, and cost about L40,000. The plans were thoroughly
worked out, down to the last detail, but the dirigible was never
constructed. Giffard went blind, and died in 1882--he stands as the
great pioneer of dirigible construction, more on the strength of the
two vessels which he actually built than on that of the ambitious later
conceptions of his brain.

In 1872 Dupuy de Lome, commissioned by the French government, built a
dirigible which he proposed to drive by man-power--it was anticipated
that the vessel would be of use in the siege of Paris, but it was not
actually tested till after the conclusion of the war. The length of
this vessel was 118 feet, its greatest diameter 49 feet, the ends being
pointed, and the motive power was by a propeller which was revolved by
the efforts of eight men. The vessel attained to about the same speed as
Giffard's steam-driven airship; it was capable of carrying fourteen
men, who, apart from these engaged in driving the propeller, had to
manipulate the pumps which controlled the air bags inside the gas
envelope.

In the same year Paul Haenlein, working in Vienna, produced an airship
which was a direct forerunner of the Lebaudy type, 164 feet in length,
30 feet greatest diameter, and with a cubic capacity of 85,000 feet.
Semi-rigidity was attained by placing the car as close to the envelope
as possible, suspending it by crossed ropes, and the motive power was
a gas engine of the Lenoir type, having four horizontal cylinders, and
giving about 5 horse-power with a consumption of about 250 cubic feet
of gas per hour. This gas was sucked from the envelope of the balloon,
which was kept fully inflated by pumping in compensating air to the air
bags inside the main envelope. A propeller, 15 feet in diameter, was
driven by the Lenoir engine at 40 revolutions per minute. This was the
first instance of the use of an internal combustion engine in connection
with aeronautical experiments.

The envelope of this dirigible was rendered airtight by means of
internal rubber coating, with a thinner film on the outside. Coal gas,
used for inflation, formed a suitable fuel for the engine, but limited
the height to which the dirigible could ascend. Such trials as were made
were carried out with the dirigible held captive, and a speed of I 5
feet per second was attained. Full experiment was prevented through
funds running low, but Haenlein's work constituted a distinct advance on
all that had been done previously.

Two brothers, Albert and Gaston Tissandier, were next to enter the field
of dirigible construction; they had experimented with balloons during
the Franc-Prussian War, and had attempted to get into Paris by balloon
during the siege, but it was not until 1882 that they produced their
dirigible.

This was 92 feet in length and 32 feet in greatest diameter, with
a cubic capacity of 37,500 feet, and the fabric used was varnished
cambric. The car was made of bamboo rods, and in addition to its crew
of three, it carried a Siemens dynamo, with 24 bichromate cells, each
of which weighed 17 lbs. The motor gave out 1 1/2 horse-power, which was
sufficient to drive the vessel at a speed of up to 10 feet per second.
This was not so good as Haenlein's previous attempt and, after L2,000
had been spent, the Tissandier abandoned their experiments, since a
5-mile breeze was sufficient to nullify the power of the motor.

Renard, a French officer who had studied the problem of dirigible
construction since 1878, associated himself first with a brother officer
named La Haye, and subsequently with another officer, Krebs, in the
construction of the second dirigible to be electrically-propelled. La
Haye first approached Colonel Laussedat, in charge of the Engineers of
the French Army, with a view to obtaining funds, but was refused, in
consequence of the practical failure of all experiments since 1870.
Renard, with whom Krebs had now associated himself, thereupon went to
Gambetta, and succeeded in getting a promise of a grant of L8,000 for
the work; with this promise Renard and Krebs set to work.

They built their airship in torpedo shape, 165 feet in length, and of
just over 27 feet greatest diameter--the greatest diameter was at the
front, and the cubic capacity was 66,000 feet. The car itself was 108
feet in length, and 4 1/2 feet broad, covered with silk over the bamboo
framework. The 23 foot diameter propeller was of wood, and was driven
by an electric motor connected to an accumulator, and yielding 8.5
horsepower. The sweep of the propeller, which might have brought it in
contact with the ground in landing, was counteracted by rendering it
possible to raise the axis on which the blades were mounted, and a guide
rope was used to obviate damage altogether, in case of rapid descent.
There was also a 'sliding weight' which was movable to any required
position to shift the centre of gravity as desired. Altogether, with
passengers and ballast aboard, the craft weighed two tons.

In the afternoon of August 8th, 1884, Renard and Krebs ascended in
the dirigible--which they had named 'La France,' from the military
ballooning ground at Chalais-Meudon, making a circular flight of about
five miles, the latter part of which was in the face of a slight
wind. They found that the vessel answered well to her rudder, and
the five-mile flight was made successfully in a period of 23 minutes.
Subsequent experimental flights determined that the air speed of the
dirigible was no less than 14 1/2 miles per hour, by far the best that
had so far been accomplished in dirigible flight. Seven flights in all
were made, and of these five were completely successful, the dirigible
returning to its starting point with no difficulty. On the other two
flights it had to be towed back.

Renard attempted to repeat his construction on a larger scale, but funds
would not permit, and the type was abandoned; the motive power was not
sufficient to permit of more than short flights, and even to the present
time electric motors, with their necessary accumulators, are far too
cumbrous to compete with the self-contained internal combustion engine.
France had to wait for the Lebaudy brothers, just as Germany had to wait
for Zeppelin and Parseval.

Two German experimenters, Baumgarten and Wolfert, fitted a Daimler motor
to a dirigible balloon which made its first ascent at Leipzig in 1880.
This vessel had three cars, and placing a passenger in one of the outer
cars[*] distributed the load unevenly, so that the whole vessel tilted
over and crashed to the earth, the occupants luckily escaping without
injury. After Baumgarten's death, Wolfert determined to carry on with
his experiments, and, having achieved a certain measure of success, he
announced an ascent to take place on the Tempelhofer Field, near Berlin,
on June 12th, 1897. The vessel, travelling with the wind, reached a
height of 600 feet, when the exhaust of the motor communicated flame to
the envelope of the balloon, and Wolfert, together with a passenger he
carried, was either killed by the fall or burnt to death on the ground.
Giffard had taken special precautions to avoid an accident of this
nature, and Wolfert, failing to observe equal care, paid the full
penalty.

[*] Hildebrandt.

Platz, a German soldier, attempting an ascent on the Tempelhofer Field
in the Schwartz airship in 1897, merely proved the dirigible a failure.
The vessel was of aluminium, 0.008 inch in thickness, strengthened by an
aluminium lattice work; the motor was two-cylindered petrol-driven; at
the first trial the metal developed such leaks that the vessel came
to the ground within four miles of its starting point. Platz, who was
aboard alone as crew, succeeded in escaping by jumping clear before the
car touched earth, but the shock of alighting broke up the balloon, and
a following high wind completed the work of full destruction. A second
account says that Platz, finding the propellers insufficient to drive
the vessel against the wind, opened the valve and descended too rapidly.

The envelope of this dirigible was 156 feet in length, and the method
of filling was that of pushing in bags, fill them with gas, and then
pulling them to pieces and tearing them out of the body of the balloon.
A second contemplated method of filling was by placing a linen envelope
inside the aluminium casing, blowing it out with air, and then admitting
the gas between the linen and the aluminium outer casing. This would
compress the air out of the linen envelope, which was to be withdrawn
when the aluminium casing had been completely filled with gas.

All this, however, assumes that the Schwartz type--the first rigid
dirigible, by the way--would prove successful. As it proved a failure on
the first trial, the problem of filling it did not arise again.

By this time Zeppelin, retired from the German army, had begun to
devote himself to the study of dirigible construction, and, a year
after Schwartz had made his experiment and had failed, he got together
sufficient funds for the formation of a limitedliability company, and
started on the construction of the first of his series of airships. The
age of tentative experiment was over, and, forerunner of the success of
the heavier-than-air type of flying machine, successful dirigible flight
was accomplished by Zeppelin in Germany, and by Santos-Dumont in France.




III. SANTOS-DUMONT

A Brazilian by birth, Santos-Dumont began in Paris in the year 1898 to
make history, which he subsequently wrote. His book, My Airships, is a
record of his eight years of work on lighter-than-air machines, a
period in which he constructed no less than fourteen dirigible balloons,
beginning with a cubic capacity of 6,350 feet, and an engine of 3
horse-power, and rising to a cubic capacity of 71,000 feet on the tenth
dirigible he constructed, and an engine of 60 horse-power, which was
fitted to the seventh machine in order of construction, the one which he
built after winning the Deutsch Prize.

The student of dirigible construction is recommended to Santos-Dumont's
own book not only as a full record of his work, but also as one of the
best stories of aerial navigation that has ever been written. Throughout
all his experiments, he adhered to the non-rigid type; his first
dirigible made its first flight on September 18th, 1898, starting from
the Jardin d'Acclimatation to the west of Paris; he calculated that his
3 horse-power engine would yield sufficient power to enable him to steer
clear of the trees with which the starting-point was surrounded, but,
yielding to the advice of professional aeronauts who were present,
with regard to the placing of the dirigible for his start, he tore the
envelope against the trees. Two days later, having repaired the balloon,
he made an ascent of 1,300 feet. In descending, the hydrogen left in
the balloon contracted, and Santos-Dumont narrowly escaped a serious
accident in coming to the ground.

His second machine, built in the early spring of 1899, held over 7,000
cubic feet of gas and gave a further 44 lbs. of ascensional force. The
balloon envelope was very long and very narrow; the first attempt at
flight was made in wind and rain, and the weather caused sufficient
contraction of the hydrogen for a wind gust to double the machine up and
toss it into the trees near its starting-point. The inventor immediately
set about the construction of 'Santos-Dumont No. 3,' on which he made a
number of successful flights, beginning on November 13th, 1899. On
the last of his flights, he lost the rudder of the machine and made a
fortunate landing at Ivry. He did not repair the balloon, considering
it too clumsy in form and its motor too small. Consequently No. 4 was
constructed, being finished on the 1st, August, 1900. It had a cubic
capacity of 14,800 feet, a length of 129 feet and greatest diameter
of 16.7 feet, the power plant being a 7 horse-power Buchet motor.
Santos-Dumont sat on a bicycle saddle fixed to the long bar suspended
under the machine, which also supported motor propeller, ballast; and
fuel. The experiment of placing the propeller at the stem instead of at
the stern was tried, and the motor gave it a speed of 100 revolutions
per minute. Professor Langley witnessed the trials of the machine, which
proved before the members of the International Congress of Aeronautics,
on September 19th, that it was capable of holding its own against a
strong wind.

Finding that the cords with which his dirigible balloon cars were
suspended offered almost as much resistance to the air as did the
balloon itself, Santos-Dumont substituted piano wire and found that the
alteration constituted greater progress than many a more showy device.
He altered the shape and size of his No. 4 to a certain extent and
fitted a motor of 12 horse-power. Gravity was controlled by shifting
weights worked by a cord; rudder and propeller were both placed at the
stern. In Santos-Dumont's book there is a certain amount of confusion
between the No. 4 and No. 5 airships, until he explains that 'No. 5'
is the reconstructed 'No. 4.' It was with No. 5 that he won the
Encouragement Prize presented by the Scientific Commission of the Paris
Aero Club. This he devoted to the first aeronaut who between May and
October of 1900 should start from St Cloud, round the Eiffel Tower,
and return. If not won in that year, the prize was to remain open the
following year from May 1st to October 1st, and so on annually until
won. This was a simplification of the conditions of the Deutsch Prize
itself, the winning of which involved a journey of 11 kilometres in 30
minutes.

The Santos-Dumont No. 5, which was in reality the modified No. 4 with
new keel, motor, and propeller, did the course of the Deutsch Prize,
but with it Santos-Dumont made no attempt to win the prize until July of
1901, when he completed the course in 40 minutes, but tore his balloon
in landing. On the 8th August, with his balloon leaking, he made
a second attempt, and narrowly escaped disaster, the airship being
entirely wrecked. Thereupon he built No. 6 with a cubic capacity of
22,239 feet and a lifting power of 1,518 lbs.

With this machine he won the Deutsch Prize on October 19th, 1901,
starting with the disadvantage of a side wind of 20 feet per second. He
reached the Eiffel Tower in 9 minutes and, through miscalculating his
turn, only just missed colliding with it. He got No. 6 under control
again and succeeded in getting back to his starting-point in 29 1/2
minutes, thus winning the 125,000 francs which constituted the Deutsch
Prize, together with a similar sum granted to him by the Brazilian
Government for the exploit. The greater part of this money was given by
Santos-Dumont to charities.

He went on building after this until he had made fourteen non-rigid
dirigibles; of these No. 12 was placed at the disposal of the military
authorities, while the rest, except for one that was sold to an American
and made only one trip, were matters of experiment for their maker. His
conclusions from his experiments may be gathered from his own work:--

'On Friday, 31st July, 1903, Commandant Hirschauer and
Lieutenant-Colonel Bourdeaux spent the afternoon with me at my airship
station at Neuilly St James, where I had my three newest airships--the
racing 'No. 7,' the omnibus 'No. 10,' and the runabout 'No. 9'--ready
for their study. Briefly, I may say that the opinions expressed by the
representatives of the Minister of War were so unreservedly favourable
that a practical test of a novel character was decided to be made.
Should the airship chosen pass successfully through it the result will
be conclusive of its military value.

'Now that these particular experiments are leaving my exclusively
private control I will say no more of them than what has been already
published in the French press. The test will probably consist of an
attempt to enter one of the French frontier towns, such as Belfort or
Nancy, on the same day that the airship leaves Paris. It will not,
of course, be necessary to make the whole journey in the airship. A
military railway wagon may be assigned to carry it, with its balloon
uninflated, with tubes of hydrogen to fill it, and with all the
necessary machinery and instruments arranged beside it. At some station
a short distance from the town to be entered the wagon may be uncoupled
from the train, and a sufficient number of soldiers accompanying the
officers will unload the airship and its appliances, transport the whole
to the nearest open space, and at once begin inflating the balloon.
Within two hours from quitting the train the airship may be ready for
its flight to the interior of the technically-besieged town.

'Such may be the outline of the task--a task presented imperiously to
French balloonists by the events of 1870-1, and which all the devotion
and science of the Tissandier brothers failed to accomplish. To-day
the problem may be set with better hope of success. All the essential
difficulties may be revived by the marking out of a hostile zone around
the town that must be entered; from beyond the outer edge of this zone,
then, the airship will rise and take its flight--across it.

'Will the airship be able to rise out of rifle range? I have always
been the first to insist that the normal place of the airship is in low
altitudes, and I shall have written this book to little purpose if
I have not shown the reader the real dangers attending any brusque
vertical mounting to considerable heights. For this we have the terrible
Severo accident before our eyes. In particular, I have expressed
astonishment at hearing of experimenters rising to these altitudes
without adequate purpose in their early stages of experience with
dirigible balloons. All this is very different, however, from a
reasoned, cautious mounting, whose necessity has been foreseen and
prepared for.'

Probably owing to the fact that his engines were not of sufficient
power, Santos-Dumont cannot be said to have solved the problem of the
military airship, although the French Government bought one of his
vessels. At the same time, he accomplished much in furthering and
inciting experiment with dirigible airships, and he will always rank
high among the pioneers of aerostation. His experiments might have
gone further had not the Wright brothers' success in America and French
interest in the problem of the heavier-than-air machine turned him from
the study of dirigibles to that of the aeroplane, in which also he takes
high rank among the pioneers, leaving the construction of a successful
military dirigible to such men as the Lebaudy brothers, Major Parseval,
and Zeppelin.




IV. THE MILITARY DIRIGIBLE

Although French and German experiment in connection with the production
of an airship which should be suitable for military purposes proceeded
side by side, it is necessary to outline the development in the two
countries separately, owing to the differing character of the work
carried out. So far as France is concerned, experiment began with the
Lebaudy brothers, originally sugar refiners, who turned their energies
to airship construction in 1899. Three years of work went to the
production of their first vessel, which was launched in 1902, having
been constructed by them together with a balloon manufacturer named
Surcouf and an engineer, Julliot. The Lebaudy airships were what is
known as semi-rigids, having a spar which ran practically the full
length of the gas bag to which it was attached in such a way as to
distribute the load evenly. The car was suspended from the spar, at
the rear end of which both horizontal and vertical rudders were fixed,
whilst stabilising fins were provided at the stern of the gas envelope
itself. The first of the Lebaudy vessels was named the 'Jaune'; its
length was 183 feet and its maximum diameter 30 feet, while the cubic
capacity was 80,000 feet. The power unit was a 40 horse-power Daimler
motor, driving two propellers and giving a maximum speed of 26 miles
per hour. This vessel made 29 trips, the last of which took place in
November, 1902, when the airship was wrecked through collision with a
tree.

The second airship of Lebaudy construction was 7 feet longer than the
first, and had a capacity of 94,000 cubic feet of gas with a triple air
bag of 17,500 cubic feet to compensate for loss of gas; this latter was
kept inflated by a rotary fan. The vessel was eventually taken over by
the French Government and may be counted the first dirigible airship
considered fit on its tests for military service.

Later vessels of the Lebaudy type were the 'Patrie' and 'Republique,'
in which both size and method of construction surpassed those of the
two first attempts. The 'Patrie' was fitted with a 60 horse-power engine
which gave a speed of 28 miles an hour, while the vessel had a radius of
280 miles, carrying a crew of nine. In the winter of 1907 the 'Patrie'
was anchored at Verdun, and encountered a gale which broke her hold
on her mooring-ropes. She drifted derelict westward across France, the
Channel, and the British Isles, and was lost in the Atlantic.

The 'Republique' had an 80 horse-power motor, which, however, only gave
her the same speed as the 'Patrie.' She was launched in July, 1908,
and within three months came to an end which constituted a tragedy
for France. A propeller burst while the vessel was in the air, and one
blade, flying toward the envelope, tore in it a great gash; the airship
crashed to earth, and the two officers and two non-commissioned officers
who were in the car were instantaneously killed.

The Clement Bayard, and subsequently the Astra-Torres, non-rigids,
followed on the early Lebaudys and carried French dirigible construction
up to 1912. The Clement Bayard was a simple non-rigid having four lobes
at the stern end to assist stability. These were found to retard
the speed of the airship, which in the second and more successful
construction was driven by a Clement Bayard motor of 100 horse-power at
a speed of 30 miles an hour. On August 23rd, 1909, while being tried for
acceptance by the military authorities, this vessel achieved a record
by flying at a height of 5,000 feet for two hours. The Astra-Torres
non-rigids were designed by a Spaniard, Senor Torres, and built by the
Astra Company. The envelope was of trefoil shape, this being due to the
interior rigging from the suspension band; the exterior appearance
is that of two lobes side by side, overlaid by a third. The interior
rigging, which was adopted with a view to decreasing air resistance,
supports a low-hung car from the centre of the envelope; steering is
accomplished by means of horizontal planes fixed on the envelope at the
stern, and vertical planes depending beneath the envelope, also at the
stern end.

One of the most successful of French pre-war dirigibles was a Clement
Bayard built in 1912. In this twin propellers were placed at the front
and horizontal and vertical rudders in a sort of box formation under the
envelope at the stern. The envelope was stream-lined, while the car of
the machine was placed well forward with horizontal controlling planes
above it and immediately behind the propellers. This airship, which
was named 'Dupuy de Lome,' may be ranked as about the most successful
non-rigid dirigible constructed prior to the War.

Experiments with non-rigids in Germany was mainly carried on by Major
Parseval, who produced his first vessel in 1906. The main feature of
this airship consisted in variation in length of the suspension cables
at the will of the operator, so that the envelope could be given an
upward tilt while the car remained horizontal in order to give the
vessel greater efficiency in climbing. In this machine, the propeller
was placed above and forward of the car, and the controlling planes were
fixed directly to the envelope near the forward end. A second vessel
differed from the first mainly in the matter of its larger size,
variable suspension being again employed, together with a similar
method of control. The vessel was moderately successful, and under Major
Parseval's direction a third was constructed for passenger carrying,
with two engines of 120 horsepower, each driving propellers of 13 feet
diameter. This was the most successful of the early German dirigibles;
it made a number of voyages with a dozen passengers in addition to its
crew, as well as proving its value for military purposes by use as
a scout machine in manoeuvres. Later Parsevals were constructed
of stream-line form, about 300 feet in length, and with engines
sufficiently powerful to give them speeds up to 50 miles an hour.

Major Von Gross, commander of a Balloon Battalion, produced semi-rigid
dirigibles from 1907 onward. The second of these, driven by two 75
horse-power Daimler motors, was capable of a speed of 27 miles an hour;
in September of 1908 she made a trip from and back to Berlin which
lasted 13 hours, in which period she covered 176 miles with four
passengers and reached a height of 4,000 feet. Her successor, launched
in April of 1909, carried a wireless installation, and the next to this,
driven by four motors of 75 horse-power each, reached a speed of 45
miles an hour. As this vessel was constructed for military purposes,
very few details either of its speed or method of construction were made
public.

Practically all these vessels were discounted by the work of Ferdinand
von Zeppelin, who set out from the first with the idea of constructing
a rigid dirigible. Beginning in 1898, he built a balloon on an aluminium
framework covered with linen and silk, and divided into interior
compartments holding linen bags which were capable of containing nearly
400,000 cubic feet of hydrogen. The total length of this first Zeppelin
airship was 420 feet and the diameter 38 feet. Two cars were rigidly
attached to the envelope, each carrying a 16 horse-power motor, driving
propellers which were rigidly connected to the aluminium framework of
the balloon. Vertical and horizontal screws were used for lifting and
forward driving and a sliding weight was used to raise or lower the stem
of the vessel out of the horizontal in order to rise or descend without
altering the load by loss of ballast or the lift by loss of gas.

The first trial of this vessel was made in July of 1900, and was
singularly unfortunate. The winch by which the sliding weight was
operated broke, and the balloon was so bent that the working of the
propellers was interfered with, as was the steering. A speed of 13 feet
per second was attained, but on descending, the airship ran against
some piles and was further damaged. Repairs were completed by the end
of September, 1900, and on a second trial flight made on October 21st a
speed of 30 feet per second was reached.

Zeppelin was far from satisfied with the performance of this vessel,
and he therefore set about collecting funds for the construction of
a second, which was completed in 1905. By this time the internal
combustion engine had been greatly improved, and without any increase of
weight, Zeppelin was able to instal two motors of 85 horse-power each.
The total capacity was 367,000 cubic feet of hydrogen, carried in 16 gas
bags inside the framework, and the weight of the whole construction
was 9 tons--a ton less than that of the first Zeppelin airship. Three
vertical planes at front and rear controlled horizontal steering, while
rise and fall was controlled by horizontal planes arranged in box form.
Accident attended the first trial of this second airship, which took
place over the Bodensee on November 30th, 1905, 'It had been intended to
tow the raft, to which it was anchored, further from the shore against
the wind. But the water was too low to allow the use of the raft. The
balloon was therefore mounted on pontoons, pulled out into the lake, and
taken in tow by a motor-boat. It was caught by a strong wind which was
blowing from the shore, and driven ahead at such a rate that it
overtook the motor-boat. The tow rope was therefore at once cut, but it
unexpectedly formed into knots and became entangled with the airship,
pulling the front end down into the water. The balloon was then caught
by the wind and lifted into the air, when the propellers were set
in motion. The front end was at this instant pointing in a downward
direction, and consequently it shot into the water, where it was found
necessary to open the valves.'[*]

[*] Hildebrandt, Airships Past and Present.

The damage done was repaired within six weeks, and the second trial
was made on January 17th, 1906. The lifting force was too great for
the weight, and the dirigible jumped immediately to 1,500 feet. The
propellers were started, and the dirigible brought to a lower level,
when it was found possible to drive against the wind. The steering
arrangements were found too sensitive, and the motors were stopped, when
the vessel was carried by the wind until it was over land--it had been
intended that the trial should be completed over water. A descent was
successfully accomplished and the dirigible was anchored for the night,
but a gale caused it so much damage that it had to be broken up. It had
achieved a speed of 30 feet per second with the motors developing only
36 horse-power and, gathering from this what speed might have been
accomplished with the full 170 horse-power, Zeppelin set about the
construction of No. 3, with which a number of successful voyages were
made, proving the value of the type for military purposes.

No. 4 was the most notable of the early Zeppelins, as much on account of
its disastrous end as by reason of any superior merit in comparison with
No. 3. The main innovation consisted in attaching a triangular keel to
the under side of the envelope, with two gaps beneath which the cars
were suspended. Two Daimler Mercedes motors of 110 horse-power each were
placed one in each car, and the vessel carried sufficient fuel for a
60-hour cruise with the motors running at full speed. Each motor drove a
pair of three-bladed metal propellers rigidly attached to the framework
of the envelope and about 15 feet in diameter. There was a vertical
rudder at the stern of the envelope and horizontal controlling planes
were fixed on the sides of the envelope. The best performances and the
end of this dirigible were summarised as follows by Major Squier:--

'Its best performances were two long trips performed during the summer
of 1908. The first, on July 4th, lasted exactly 12 hours, during which
time it covered a distance of 235 miles, crossing the mountains
to Lucerne and Zurich, and returning to the balloon-house near
Friedrichshafen, on Lake Constance. The average speed on this trip
was 32 miles per hour. On August 4th, this airship attempted a 24-hour
flight, which was one of the requirements made for its acceptance by the
Government. It left Friedrichshafen in the morning with the intention
of following the Rhine as far as Mainz, and then returning to its
starting-point, straight across the country. A stop of 3 hours 30
minutes was made in the afternoon of the first day on the Rhine, to
repair the engine. On the return, a second stop was found necessary near
Stuttgart, due to difficulties with the motors, and some loss of gas.
While anchored to the ground, a storm arose which broke loose the
anchorage, and, as the balloon rose in the air, it exploded and took
fire (due to causes which have never been actually determined and
published) and fell to the ground, where it was completely destroyed. On
this journey, which lasted in all 31 hours 15 minutes, the airship was
in the air 20 hours 45 minutes, and covered a total distance of 378
miles.

'The patriotism of the German nation was aroused. Subscriptions were
immediately started, and in a short space of time a quarter of a million
pounds had been raised. A Zeppelin Society was formed to direct the
expenditure of this fund. Seventeen thousand pounds has been expended in
purchasing land near Friedrichshafen; workshops were erected, and it was
announced that within one year the construction of eight airships of the
Zeppelin type would be completed. Since the disaster to 'Zeppelin IV.'
the Crown Prince of Germany made a trip in 'Zeppelin No. 3,' which had
been called back into service, and within a very few days the German
Emperor visited Friedrichshafen for the purpose of seeing the airship in
flight. He decorated Count Zeppelin with the order of the Black Eagle.
German patriotism and enthusiasm has gone further, and the "German
Association for an Aerial Fleet" has been organised in sections
throughout the country. It announces its intention of building 50
garages (hangars) for housing airships.'

By January of 1909, with well over a quarter of a million in hand for
the construction of Zeppelin airships, No. 3 was again brought out,
probably in order to maintain public enthusiasm in respect of the
possible new engine of war. In March of that year No. 3 made a voyage
which lasted for 4 hours over and in the vicinity of Lake Constance; it
carried 26 passengers for a distance of nearly 150 miles.

Before the end of March, Count Zeppelin determined to voyage from
Friedrichshafen to Munich, together with the crew of the airship and
four military officers. Starting at four in the morning and ascertaining
their route from the lights of railway stations and the ringing of bells
in the towns passed over, the journey was completed by nine o'clock, but
a strong south-west gale prevented the intended landing. The airship
was driven before the wind until three o'clock in the afternoon, when it
landed safely near Dingolfing; by the next morning the wind had fallen
considerably and the airship returned to Munich and landed on the parade
ground as originally intended. At about 3.30 in the afternoon, the
homeward journey was begun, Friedrichshafen being reached at about 7.30.

These trials demonstrated that sufficient progress had been made to
justify the construction of Zeppelin airships for use with the German
army. No. 3 had been manoeuvred safely if not successfully in half a
gale of wind, and henceforth it was known as 'SMS. Zeppelin I.,' at the
bidding of the German Emperor, while the construction of 'SMS. Zeppelin
II.' was rapidly proceeded with. The fifth construction of Count
Zeppelin's was 446 feet in length, 42 1/2 feet in diameter,
and contained 530,000 cubic feet of hydrogen gas in 17 separate
compartments. Trial flights were made on the 26th May, 1909, and a week
later she made a record voyage of 940 miles, the route being from Lake
Constance over Ulm, Nuremberg, Leipzig, Bitterfeld, Weimar, Heilbronn,
and Stuttgart, descending near Goppingen; the time occupied in the
flight was upwards of 38 hours.

In landing, the airship collided with a pear-tree, which damaged the
bows and tore open two sections of the envelope, but repairs on the
spot enabled the return journey to Friedrichshafen to be begun 24 hours
later. In spite of the mishap the Zeppelin had once more proved itself
as a possible engine of war, and thenceforth Germany pinned its faith
to the dirigible, only developing the aeroplane to such an extent as
to keep abreast of other nations. By the outbreak of war, nearly 30
Zeppelins had been constructed; considerably more than half of these
were destroyed in various ways, but the experiments carried on with
each example of the type permitted of improvements being made. The first
fatality occurred in September, 1913, when the fourteenth Zeppelin to be
constructed, known as Naval Zeppelin L.1, was wrecked in the North Sea
by a sudden storm and her crew of thirteen were drowned. About three
weeks after this, Naval Zeppelin L.2, the eighteenth in order of
building, exploded in mid-air while manoeuvring over Johannisthal. She
was carrying a crew of 25, who were all killed.

By 1912 the success of the Zeppelin type brought imitators. Chief among
them was the Schutte-Lanz, a Mannheim firm, which produced a rigid
dirigible with a wooden framework, wire braced. This was not a cylinder
like the Zeppelin, but reverted to the cigar shape and contained about
the same amount of gas as the Zeppelin type. The Schutte-Lanz was made
with two gondolas rigidly attached to the envelope in which the gas bags
were placed. The method of construction involved greater weight than was
the case with the Zeppelin, but the second of these vessels, built with
three gondolas containing engines, and a navigating cabin built into
the hull of the airship itself, proved quite successful as a naval scout
until wrecked on the islands off the coast of Denmark late in 1914. The
last Schutte-Lanz to be constructed was used by the Germans for raiding
England, and was eventually brought down in flames at Cowley.




V. BRITISH AIRSHIP DESIGN

As was the case with the aeroplane, Great Britain left France and
Germany to make the running in the early days of airship construction;
the balloon section of the Royal Engineers was compelled to confine
its energies to work with balloons pure and simple until well after
the twentieth century had dawned, and such experiments as were made
in England were done by private initiative. As far back as 1900 Doctor
Barton built an airship at the Alexandra Palace and voyaged across
London in it. Four years later Mr E. T. Willows of Cardiff produced the
first successful British dirigible, a semi-rigid 74 feet in length and
18 feet in diameter, engined with a 7 horse-power Peugot twin-cylindered
motor. This drove a two-bladed propeller at the stern for propulsion,
and also actuated a pair of auxiliary propellers at the front which
could be varied in their direction so as to control the right and left
movements of the airship. This device was patented and the patent was
taken over by the British Government, which by 1908 found Mr Willow's
work of sufficient interest to regard it as furnishing data for
experiment at the balloon factory at Farnborough. In 1909, Willows
steered one of his dirigibles to London from Cardiff in a little less
than ten hours, making an average speed of over 14 miles an hour. The
best speed accomplished was probably considerably greater than this,
for at intervals of a few miles, Willows descended near the earth to
ascertain his whereabouts with the help of a megaphone. It must be added
that he carried a compass in addition to his megaphone. He set out for
Paris in November of 1910, reached the French coast, and landed near
Douai. Some damage was sustained in this landing, but, after repair, the
trip to Paris was completed.

Meanwhile the Government balloon factory at Farnborough began airship
construction in 1907; Colonel Capper, R.E., and S. F. Cody were jointly
concerned in the production of a semi-rigid. Fifteen thicknesses of
goldbeaters' skin--about the most expensive covering obtainable--were
used for the envelope, which was 25 feet in diameter. A slight shower of
rain in which the airship was caught led to its wreckage, owing to the
absorbent quality of the goldbeaters' skin, whereupon Capper and Cody
set to work to reproduce the airship and its defects on a larger scale.
The first had been named 'Nulli Secundus' and the second was named
'Nulli Secundus II.' Punch very appropriately suggested that the first
vessel ought to have been named 'Nulli Primus,' while a possible third
should be christened 'Nulli Tertius.' 'Nulli Secundus II.' was fitted
with a 100 horse-power engine and had an envelope of 42 feet in
diameter, the goldbeaters' skin being covered in fabric and the car
being suspended by four bands which encircled the balloon envelope.
In October of 1907, 'Nulli Secundus II.' made a trial flight from
Farnborough to London and was anchored at the Crystal Palace. The wind
sprung up and took the vessel away from its mooring ropes, wrecking it
after the one flight.

Stagnation followed until early in 1909, when a small airship fitted
with two 12 horse-power motors and named the 'Baby' was turned out from
the balloon factory. This was almost egg-shaped, the blunt end being
forward, and three inflated fins being placed at the tail as control
members. A long car with rudder and elevator at its rear-end carried
the engines and crew; the 'Baby' made some fairly successful flights and
gave a good deal of useful data for the construction of later vessels.

Next to this was 'Army Airship 2A 'launched early in 1910 and larger,
longer, and narrower in design than the Baby. The engine was an 80
horse-power Green motor which drove two pairs of propellers; small
inflated control members were fitted at the stern end of the envelope,
which was 154 feet in length. The suspended car was 84 feet long,
carrying both engines and crew, and the Willows idea of swivelling
propellers for governing the direction was used in this vessel. In June
of that year a new, small-type dirigible, the 'Beta,' was produced,
driven by a 30 horse-power Green engine with which she flew over 3,000
miles. She was the most successful British dirigible constructed up to
that time, and her successor, the 'Gamma,' was built on similar lines.
The 'Gamma' was a larger vessel, however, produced in 1912, with flat,
controlling fins and rudder at the rear end of the envelope, and with
the conventional long car suspended at some distance beneath the gas
bag. By this time, the mooring mast, carrying a cap of which the concave
side fitted over the convex nose of the airship, had been originated.
The cap was swivelled, and, when attached to it, an airship was held
nose on to the wind, thus reducing by more than half the dangers
attendant on mooring dirigibles in the open.

Private subscription under the auspices of the Morning Post got together
sufficient funds in 1910 for the purchase of a Lebaudy airship, which
was built in France, flown across the Channel, and presented to the Army
Airship Fleet. This dirigible was 337 feet long, and was driven by two
135 horse-power Panhard motors, each of which actuated two propellers.
The journey from Moisson to Aldershot was completed at a speed of 36
miles an hour, but the airship was damaged while being towed into its
shed. On May of the following year, the Lebaudy was brought out for a
flight, but, in landing, the guide rope fouled in trees and sheds and
brought the airship broadside on to the wind; she was driven into some
trees and wrecked to such an exteent that rebuilding was considered an
impossibility. A Clement Bayard, bought by the army airship section,
became scrap after even less flying than had been accomplished by the
Lebaudy.

In April of 1910, the Admiralty determined on a naval air service,
and set about the production of rigid airships which should be able to
compete with Zeppelins as naval scouts. The construction was entrusted
to Vickers, Ltd., who set about the task at their Barrow works and built
something which, when tested after a year's work, was found incapable
of lifting its own weight. This defect was remedied by a series of
alterations, and meanwhile the unofficial title of 'Mayfly' was given to
the vessel.

Taken over by the Admiralty before she had passed any flying tests,
the 'Mayfly' was brought out on September 24th, 1911, for a trial trip,
being towed out from her shed by a tug. When half out from the shed,
the envelope was caught by a light cross-wind, and, in spite of the pull
from the tug, the great fabric broke in half, nearly drowning the crew,
who had to dive in order to get clear of the wreckage.

There was considerable similarity in form, though not in performance,
between the Mayfly and the prewar Zeppelin. The former was 510 feet in
length, cylindrical in form, with a diameter of 48 feet, and divided
into 19 gas-bag compartments. The motive power consisted of two 200
horse-power Wolseley engines. After its failure, the Naval Air Service
bought an Astra-Torres airship from France and a Parseval from Germany,
both of which proved very useful in the early days of the War, doing
patrol work over the Channel before the Blimps came into being.

Early in 1915 the 'Blimp' or 'S.S.' type of coastal airship was evolved
in response to the demand for a vessel which could be turned out quickly
and in quantities. There was urgent demand, voiced by Lord Fisher, for
a type of vessel capable of maintaining anti-submarine patrol off the
British coasts, and the first S.S. airships were made by combining a
gasbag with the most available type of aeroplane fuselage and engine,
and fitting steering gear. The 'Blimp' consisted of a B.E. fuselage with
engine and geared-down propeller, and seating for pilot and observer,
attached to an envelope about 150 feet in length. With a speed of
between 35 and 40 miles an hour, the 'Blimp' had a cruising capacity of
about ten hours; it was fitted with wireless set, camera, machine-gun,
and bombs, and for submarine spotting and patrol work generally it
proved invaluable, though owing to low engine power and comparatively
small size, its uses were restricted to reasonably fair weather. For
work farther out at sea and in all weathers, airships known as the coast
patrol type, and more commonly as 'coastals,' were built, and later
the 'N.S.' or North Sea type, still larger and more weather-worthy,
followed. By the time the last year of the War came, Britain led the
world in the design of non-rigid and semi-rigid dirigibles. The 'S.S.'
or 'Blimp' had been improved to a speed of 50 miles an hour, carrying a
crew of three, and the endurance record for the type was 18 1/2 hours,
while one of them had reached a height of 10,000 feet. The North Sea
type of non-rigid was capable of travelling over 20 hours at full speed,
or forty hours at cruising speed, and the number of non-rigids belonging
to the British Navy exceeded that of any other country.

It was owing to the incapacity--apparent or real--of the British
military or naval designers to produce a satisfactory rigid airship that
the 'N.S.' airship was evolved. The first of this type was produced
in 1916, and on her trials she was voted an unqualified success, in
consequence of which the building of several more was pushed on. The
envelope, of 360,000 cubic feet capacity, was made on the Astra-Torres
principle of three lobes, giving a trefoil section. The ship carried
four fins, to three of which the elevator and rudder flaps were
attached; petrol tanks were placed inside the envelope, under which
was rigged a long covered-in car, built up of a light steel tubular
framework 35 feet in length. The forward portion was covered with
duralumin sheeting, an aluminium alloy which, unlike aluminium itself,
is not affected by the action of sea air and water, and the remainder
with fabric laced to the framework. Windows and port-holes were provided
to give light to the crew, and the controls and navigating instruments
were placed forward, with the sleeping accommodation aft. The engines
were mounted in a power unit structure, separate from the car and
connected by wooden gang ways supported by wire cables. A complete
electrical installation of two dynamos and batteries for lights,
signalling lamps, wireless, telephones, etc., was carried, and the
motive power consisted of either two 250 horse-power Rolls-Royce engines
or two 240 horse-power Fiat engines. The principal dimensions of this
type are length 262 feet, horizontal diameter 56 feet 9 inches, vertical
diameter 69 feet 3 inches. The gross lift is 24,300 lbs. and the
disposable lift without crew, petrol, oil, and ballast 8,500 lbs. The
normal crew carried for patrol work was ten officers and men. This type
holds the record of 101 hours continuous flight on patrol duty.

In the matter of rigid design it was not until 1913 that the British
Admiralty got over the fact that the 'Mayfly' would not, and decided on
a further attempt at the construction of a rigid dirigible. The
contract for this was signed in March of 1914; work was suspended in the
following February and begun again in July, 1915, but it was not until
January of 1917 that the ship was finished, while her trials were not
completed until March of 1917, when she was taken over by the Admiralty.
The details of the construction and trial of this vessel, known as 'No.
9,' go to show that she did not quite fill the contract requirements in
respect of disposable lift until a number of alterations had been made.
The contract specified that a speed of at least 45 miles per hour was to
be attained at full engine power, while a minimum disposable lift of 5
tons was to be available for movable weights, and the airship was to
be capable of rising to a height of 2,000 feet. Driven by four Wolseley
Maybach engines of 180 horse-power each, the lift of the vessel was not
sufficient, so it was decided to remove the two engines in the after
car and replace them by a single engine of 250 horsepower. With this the
vessel reached the contract speed of 45 miles per hour with a cruising
radius of 18 hours, equivalent to 800 miles when the engines were
running at full speed. The vessel served admirably as a training
airship, for, by the time she was completed, the No. 23 class of rigid
airship had come to being, and thus No. 9 was already out of date.

Three of the 23 class were completed by the end of 1917; it was
stipulated that they should be built with a speed of at least 55 miles
per hour, a minimum disposable lift of 8 tons, and a capability of
rising at an average rate of not less than 1,000 feet per minute to a
height of 3,000 feet. The motive power consisted of four 250 horse-power
Rolls-Royce engines, one in each of the forward and after cars and two
in a centre car. Four-bladed propellers were used throughout the ship.

A 23X type followed on the 23 class, but by the time two ships had been
completed, this was practically obsolete. The No. 31 class followed the
23X; it was built on Schutte-Lanz lines, 615 feet in length, 66 feet
diameter, and a million and a half cubic feet capacity. The hull was
similar to the later types of Zeppelin in shape, with a tapering stern
and a bluff, rounded bow. Five cars each carrying a 250 horse-power
Rolls-Royce engine, driving a single fixed propeller, were fitted, and
on her trials R.31 performed well, especially in the matter of speed.
But the experiment of constructing in wood in the Schutte-Lanz way
adopted with this vessel resulted in failure eventually, and the type
was abandoned.

Meanwhile, Germany had been pushing forward Zeppelin design
and straining every nerve in the improvement of rigid dirigible
construction, until L.33 was evolved; she was generally known as
a super-Zeppelin, and on September 24th, 1916, six weeks after her
launching, she was damaged by gun-fire in a raid over London, being
eventually compelled to come to earth at Little Wigborough in Essex. The
crew gave themselves up after having set fire to the ship, and though
the fabric was totally destroyed, the structure of the hull remained
intact, so that just as Germany was able to evolve the Gotha bomber from
the Handley-Page delivered at Lille, British naval constructors were able
to evolve the R.33 type of airship from the Zeppelin framework delivered
at Little Wigborough. Two vessels, R.33 and R.34, were laid down for
completion; three others were also put down for construction, but, while
R.33 and R.34 were built almost entirely from the data gathered from
the wrecked L.33, the three later vessels embody more modern design,
including a number of improvements, and more especially greater
disposable lift. It has been commented that while the British
authorities were building R.33 and R.34, Germany constructed 30
Zeppelins on 4 slips, for which reason it may be reckoned a matter for
congratulation that the rigid airship did not decide the fate of the
War. The following particulars of construction of the R.33 and R.34
types are as given by Major Whale in his survey of British Airships:--

'In all its main features the hull structure of R.33 and R.34 follows
the design of the wrecked German Zeppelin airship L.33. 'The hull
follows more nearly a true stream-line shape than in the previous ships
constructed of duralumin, in which a greater proportion of the greater
length was parallel-sided. The Germans adopted this new shape from
the Schutte-Lanz design and have not departed from this practice. This
consists of a short, parallel body with a long, rounded bow and a long
tapering stem culminating in a point. The overall length of the ship is
643 feet with a diameter of 79 feet and an extreme height of 92 feet.

'The type of girders in this class has been much altered from those
in previous ships. The hull is fitted with an internal triangular keel
throughout practically the entire length. This forms the main corridor
of the ship, and is fitted with a footway down the centre for its entire
length. It contains water ballast and petrol tanks, bomb storage and
crew accommodation, and the various control wires, petrol pipes, and
electric leads are carried along the lower part.

'Throughout this internal corridor runs a bridge girder, from which
the petrol and water ballast tanks are supported. These tanks are so
arranged that they can be dropped clear of the ship. Amidships is the
cabin space with sufficient room for a crew of twenty-five. Hammocks can
be swung from the bridge girder before mentioned.

'In accordance with the latest Zeppelin practice, monoplane rudders and
elevators are fitted to the horizontal and vertical fins.

'The ship is supported in the air by nineteen gas bags, which give a
total capacity of approximately two million cubic feet of gas. The gross
lift works out at approximately 59 1/2 tons, of which the total fixed
weight is 33 tons, giving a disposable lift of 26 1/2 tons.

'The arrangement of cars is as follows: At the forward end the control
car is slung, which contains all navigating instruments and the various
controls. Adjoining this is the wireless cabin, which is also fitted
for wireless telephony. Immediately aft of this is the forward power car
containing one engine, which gives the appearance that the whole is one
large car.

'Amidships are two wing cars, each containing a single engine. These
are small and just accommodate the engines with sufficient room for
mechanics to attend to them. Further aft is another larger car which
contains an auxiliary control position and two engines.

'It will thus be seen that five engines are installed in the ship;
these are all of the same type and horsepower, namely, 250 horse-power
Sunbeam. R.33 was constructed by Messrs Armstrong, Whitworth, Ltd.;
while her sister ship R.34 was built by Messrs Beardmore on the Clyde.'

Of the two vessels, R.34 appeared rather more airworthy than her sister
ship; the lift of the ship justified the carrying of a greater quantity
of fuel than had been provided for, and, as she was considered suitable
for making a Transatlantic crossing, extra petrol tanks were fitted in
the hull and a new type of outer cover was fitted with a view to her
making the Atlantic crossing. She made a 21-hour cruise over the North
of England and the South of Scotland at the end of May, 1919, and
subsequently went for a longer cruise over Denmark, the Baltic, and the
north coast of Germany, remaining in the air for 56 hours in spite
of very bad weather conditions. Finally, July 2nd was selected as the
starting date for the cross Atlantic flight; the vessel was commanded
by Major G. H. Scott, A.F.C., with Captain G. S. Greenland as first
officer, Second-Lieut. H. F. Luck as second officer, and Lieut. J. D.
Shotter as engineer officer. There were also on board Brig.-Gen. E.
P. Maitland, representing the Air Ministry, Major J. E. M. Pritchard,
representing the Admiralty, and Lieut.-Col. W. H. Hemsley of the Army
Aviation Department. In addition to eight tons of petrol, R.34 carried a
total number of 30 persons from East Fortune to Long Island, N.Y.

There being no shed in America capable of accommodating the airship,
she had to be moored in the open for refilling with fuel and gas, and to
make the return journey almost immediately.

Brig.-Gen. Maitland's account of the flight, in itself a record as
interesting as valuable, divides the outward journey into two main
stages, the first from East Fortune to Trinity Bay, Newfoundland, a
distance of 2,050 sea miles, and the second and more difficult stage
to Mineola Field, Long Island, 1,080 sea miles. An easy journey
was experienced until Newfoundland was reached, but then storms and
electrical disturbances rendered it necessary to alter the course, in
consequence of which petrol began to run short. Head winds rendered the
shortage still more acute, and on Saturday, July 5th, a wireless signal
was sent out asking for destroyers to stand by to tow. However, after an
anxious night, R.33 landed safely at Mineola Field at 9.55 a.m. on July
6th, having accomplished the journey in 108 hours 12 minutes.

She remained at Mineola until midnight of July 9th, when, although
it had been intended that a start should be made by daylight for the
benefit of New York spectators, an approaching storm caused preparations
to be advanced for immediate departure. She set out at 5.57 a.m.
by British summer time, and flew over New York in the full glare
of hundreds of searchlights before heading out over the Atlantic. A
following wind assisted the return voyage, and on July 13th, at 7.57
a.m., R.34 anchored at Pulham, Norfolk, having made the return journey
in 75 hours 3 minutes, and proved the suitability of the dirigible
for Transatlantic commercial work. R.80, launched on July 19th, 1920,
afforded further proof, if this were needed.

It is to be noted that nearly all the disasters to airships have been
caused by launching and landing--the type is safe enough in the air,
under its own power, but its bulk renders it unwieldy for ground
handling. The German system of handling Zeppelins in and out of their
sheds is, so far, the best devised: this consists of heavy trucks
running on rails through the sheds and out at either end; on descending,
the trucks are run out, and the airship is securely attached to them
outside the shed; the trucks are then run back into the shed, taking the
airship with them, and preventing any possibility of the wind driving
the envelope against the side of the shed before it is safely housed;
the reverse process is adopted in launching, which is thus rendered as
simple as it is safe.




VI. THE AIRSHIP COMMERCIALLY

Prior to the war period, between the years 1910 and 1914, a German
undertaking called the Deutsche Luftfahrt Actien Gesellschaft conducted
a commercial Zeppelin service in which four airships known as the
Sachsan, Hansa, Victoria Louise, and Schwaben were used. During the four
years of its work, the company carried over 17,000 passengers, and over
100,000 miles were flown without incurring one fatality and with only
minor and unavoidable accidents to the vessels composing the service.
Although a number of English notabilities made voyages in these
airships, the success of this only experiment in commercial aerostation
seems to have been forgotten since the war. There was beyond doubt a
military aim in this apparently peaceful use of Zeppelin airships; it is
past question now that all Germany's mechanical development in respect
of land sea, and air transport in the years immediately preceding the
war, was accomplished with the ulterior aim of military conquest, but,
at the same time, the running of this service afforded proof of the
possibility of establishing a dirigible service for peaceful ends, and
afforded proof too, of the value of the dirigible as a vessel of purely
commercial utility.

In considering the possibility of a commercial dirigible service, it
is necessary always to bear in mind the disadvantages of first cost and
upkeep as compared with the aeroplane. The building of a modern rigid
is an exceedingly costly undertaking, and the provision of an efficient
supply of hydrogen gas to keep its compartments filled is a very large
item in upkeep of which the heavier-than-air machine goes free. Yet
the future of commercial aeronautics so far would seem to lie with the
dirigible where very long voyages are in question. No matter how the
aeroplane may be improved, the possibility of engine failure always
remains as a danger for work over water. In seaplane or flying boat
form, the danger is still present in a rough sea, though in the American
Transatlantic flight, N.C.3, taxi-ing 300 miles to the Azores after
having fallen to the water, proved that this danger is not so acute as
is generally assumed. Yet the multiple-engined rigid, as R.34 showed on
her return voyage, may have part of her power plant put out of action
altogether and still complete her voyage very successfully, which, in
the case of mail carrying and services run strictly to time, gives her
an enormous advantage over the heavier-than-air machine.

'For commercial purposes,' General Sykes has remarked, 'the airship is
eminently adapted for long distance journeys involving non-stop flights.
It has this inherent advantage over the aeroplane, that while there
appears to be a limit to the range of the aeroplane as at present
constructed, there is practically no limit whatever to that of the
airship, as this can be overcome by merely increasing the size. It thus
appears that for such journeys as crossing the Atlantic, or crossing
the Pacific from the west coast of America to Australia or Japan, the
airship will be peculiarly suitable. It having been conceded that the
scope of the airship is long distance travel, the only type which need
be considered for this purpose is the rigid. The rigid airship is still
in an embryonic state, but sufficient has already been accomplished
in this country, and more particularly in Germany, to show that with
increased capacity there is no reason why, within a few years' time,
airships should not be built capable of completing the circuit of the
globe and of conveying sufficient passengers and merchandise to render
such an undertaking a paying proposition.'

The British R.38 class, embodying the latest improvements in airship
design outside Germany, gives a gross lift per airship of 85 tons and a
net lift of about 45 tons. The capacity of the gas bags is about two
and three-quarter million cubic feet, and, travelling at the rate of
45 miles per hour, the cruising range of the vessel is estimated at 8.8
days. Six engines, each of 350 horse-power, admit of an extreme speed of
70 miles per hour if necessary.

The last word in German design is exemplified in the rigids L.70 and
L.71, together with the commercial airship 'Bodensee.' Previous to the
construction of these, the L.65 type is noteworthy as being the first
Zeppelin in which direct drive of the propeller was introduced, together
with an improved and lighter type of car. L.70 built in 1918 and
destroyed by the British naval forces, had a speed of about 75 miles per
hour; L.71 had a maximum speed of 72 miles per hour, a gas bag capacity
of 2,420,000 cubic feet, and a length of 743 feet, while the total lift
was 73 tons. Progress in design is best shown by the progress in useful
load; in the L.70 and L.71 class, this has been increased to 58.3 per
cent, while in the Bodensee it was ever higher.

As was shown in R.34's American flight, the main problem in connection
with the commercial use of dirigibles is that of mooring in the open.
The nearest to a solution of this problem, so far, consists in the mast
carrying a swivelling cap; this has been tried in the British service
with a non-rigid airship, which was attached to a mast in open country
in a gale of 52 miles an hour without the slightest damage to the
airship. In its commercial form, the mast would probably take the
form of a tower, at the top of which the cap would revolve so that
the airship should always face the wind, the tower being used for
embarkation and disembarkation of passengers and the provision of fuel
and gas. Such a system would render sheds unnecessary except in case of
repairs, and would enormously decrease the establishment charges of any
commercial airship.

All this, however, is hypothetical. Remains the airship of to-day,
developed far beyond the promise of five years ago, capable, as has
been proved by its achievements both in Britain and in Germany, of
undertaking practically any given voyage with success.




VII. KITE BALLOONS

As far back as the period of the Napoleonic wars, the balloon was
given a place in warfare, but up to the Franco-Prussian Prussian War
of 1870-71 its use was intermittent. The Federal forces made use of
balloons to a small extent in the American Civil War; they came to great
prominence in the siege of Paris, carrying out upwards of three million
letters and sundry carrier pigeons which took back messages into the
besieged city. Meanwhile, as captive balloons, the German and other
armies used them for observation and the direction of artillery fire. In
this work the ordinary spherical balloon was at a grave disadvantage; if
a gust of wind struck it, the balloon was blown downward and down
wind, generally twirling in the air and upsetting any calculations and
estimates that might be made by the observers, while in a wind of 25
miles an hour it could not rise at all. The rotatory movement caused by
wind was stopped by an experimenter in the Russo-Japanese war, who fixed
to the captive observation balloons a fin which acted as a rudder. This
did not stop the balloon from being blown downward and away from its
mooring station, but this tendency was overcome by a modification
designed in Germany by the Parseval-Siegsfield Company, which originated
what has since become familiar as the 'Sausage' or kite balloon. This
is so arranged that the forward end is tilted up into the wind, and the
underside of the gas bag, acting as a plane, gives the balloon a lifting
tendency in a wind, thus counteracting the tendency of the wind to blow
it downward and away from its mooring station. Smaller bags are fitted
at the lower and rear end of the balloon with openings that face into
the wind; these are thus kept inflated, and they serve the purpose of a
rudder, keeping the kite balloon steady in the air.

Various types of kite balloon have been introduced; the original German
Parseval-Siegsfield had a single air bag at the stern end, which was
modified to two, three, or more lobes in later varieties, while an
American experimental design attempted to do away with the attached
lobes altogether by stringing out a series of small air bags, kite
fashion, in rear of the main envelope. At the beginning of the War,
Germany alone had kite balloons, for the authorities of the Allied
armies con-sidered that the bulk of such a vessel rendered it too
conspicuous a mark to permit of its being serviceable. The Belgian
arm alone possessed two which, on being put into service, were found
extremely useful. The French followed by constructing kite balloons at
Chalais Meudon, and then, after some months of hostilities and with the
example of the Royal Naval Air Service to encourage them, the British
military authorities finally took up the construction and use of kite
balloons for artillery-spotting and general observation purposes.
Although many were brought down by gun-fire, their uses far outweighed
their disadvantages, and toward the end of the War, hardly a mile of
front was without its 'Sausage.'

For naval work, kite balloons were carried in a specially constructed
hold in the forepart of certain vessels; when required for use, the
covering of the hold was removed, the kite balloon inflated and released
to the required height by means of winches as in the case of the
land work. The perfecting of the 'Coastal' and N.S. types of airship,
together with the extension of wireless telephony between airship and
cruiser or other warship, in all probability will render the use of the
kite balloon unnecessary in connection with naval scouting. But, during
the War, neither wireless telephony nor naval airships had developed
sufficiently to render the Navy independent of any means that might come
to hand, and the fitting of kite balloons in this fashion filled a need
of the times.

A necessary accessory of the kite balloon is the parachute, which has
a long history. Da Vinci and Veranzio appear to have been the first
exponents, the first in the theory and the latter in the practice of
parachuting. Montgolfier experimented at Annonay before he constructed
his first hot air-balloon, and in 1783 a certain Lenormand dropped from
a tree in a parachute. Blanchard the balloonist made a spectacle
of parachuting, and made it a financial success; Cocking, in 1836,
attempted to use an inverted form of parachute; taken up to a height
of 3,000 feet, he was cut adrift, when the framework of the parachute
collapsed and Cocking was killed.

The rate of fall is slow in parachuting to the ground. Frau Poitevin,
making a descent from a height of 6,000 feet, took 45 minutes to reach
the ground, and, when she alighted, her husband, who had taken her up,
had nearly got his balloon packed up. Robertson, another parachutist is
said to have descended from a height of 10,000 feet in 35 minutes, or
at a rate of nearly 5 feet per second. During the War Brigadier-General
Maitland made a parachute descent from a height of 10,000 feet, the time
taken being about 20 minutes.

The parachute was developed considerably during the War period, the main
requirement, that of certainty in opening, being considerably developed.
Considered a necessary accessory for kite balloons, the parachute was
also partially adopted for use with aeroplanes in the later War period,
when it was contended that if a machine were shot down in flames, its
occupants would be given a far better chance of escape if they had
parachutes. Various trials were made to demonstrate the extreme
efficiency of the parachute in modern form, one of them being a descent
from the upper ways of the Tower Bridge to the waters of the Thames, in
which short distance the 'Guardian Angel' type of parachute opened and
cushioned the descent for its user.

For dirigibles, balloons, and kite balloons the parachute is an
essential. It would seem to be equally essential in the case of
heavier-than-air machines, but this point is still debated. Certainly
it affords the occupant of a falling aeroplane a chance, no matter how
slender, of reaching the ground in safety, and, for that reason, it
would seem to have a place in aviation as well as in aerostation.




PART IV. ENGINE DEVELOPMENT




I. THE VERTICAL TYPE

The balloon was but a year old when the brothers Robert, in 1784
attempted propulsion of an aerial vehicle by hand-power, and succeeded,
to a certain extent, since they were able to make progress when there
was only a slight wind to counteract their work. But, as may be easily
understood, the manual power provided gave but a very slow speed, and in
any wind it all the would-be airship became an uncontrolled balloon.

Henson and Stringfellow, with their light steam engines, were first to
attempt conquest of the problem of mechanical propulsion in the
air; their work in this direction is so fully linked up with their
constructed models that it has been outlined in the section dealing
with the development of the aeroplane. But, very shortly after these
two began, there came into the field a Monsieur Henri Giffard, who first
achieved success in the propulsion by mechanical means of dirigible
balloons, for his was the first airship to fly against the wind.
He employed a small steam-engine developing about 3 horse-power and
weighing 350 lbs. with boiler, fitting the whole in a car suspended from
the gas-bag of his dirigible. The propeller which this engine worked
was 11 feet in diameter, and the inventor, who made several flights,
obtained a speed of 6 miles an hour against a slight wind. The power
was not sufficient to render the invention practicable, as the dirigible
could only be used in calm weather, but Giffard was sufficiently
encouraged by his results to get out plans for immense dirigibles,
which through lack of funds he was unable to construct. When, later, his
invention of the steam-injector gave him the means he desired, he became
blind, and in 1882 died, having built but the one famous dirigible.

This appears to have been the only instance of a steam engine being
fitted to a dirigible; the inherent disadvantage of this form of motive
power is that a boiler to generate the steam must be carried, and this,
together with the weight of water and fuel, renders the steam engine
uneconomical in relation to the lift either of plane or gas-bag. Again,
even if the weight could be brought down to a reasonable amount, the
attention required by steam plant renders it undesirable as a motive
power for aircraft when compared with the internal combustion engine.

Maxim, in Artificial and Natural Flight, details the engine which he
constructed for use with his giant experimental flying machine, and his
description is worthy of reproduction since it is that of the only steam
engine besides Giffard's, and apart from those used for the propulsion
of models, designed for driving an aeroplane. 'In 1889,' Maxim says,
'I had my attention drawn to some very thin, strong, and comparatively
cheap tubes which were being made in France, and it was only after I had
seen these tubes that I seriously considered the question of making a
flying machine. I obtained a large quantity of them and found that they
were very light, that they would stand enormously high pressures, and
generate a very large quantity of steam. Upon going into a mathematical
calculation of the whole subject, I found that it would be possible to
make a machine on the aeroplane system, driven by a steam engine, which
would be sufficiently strong to lift itself into the air. I first made
drawings of a steam engine, and a pair of these engines was afterwards
made. These engines are constructed, for the most part, of a very high
grade of cast steel, the cylinders being only 3/32 of an inch thick,
the crank shafts hollow, and every part as strong and light as possible.
They are compound, each having a high-pressure piston with an area of
20 square inches, a low-pressure piston of 50.26 square inches, and a
common stroke of 1 foot. When first finished they were found to weigh
300 lbs. each; but after putting on the oil cups, felting, painting, and
making some slight alterations, the weight was brought up to 320 lbs.
each, or a total of 640 lbs. for the two engines, which have since
developed 362 horsepower with a steam pressure of 320 lbs. per square
inch.'

The result is remarkable, being less than 2 lbs. weight per horse-power,
especially when one considers the state of development to which the
steam engine had attained at the time these experiments were made. The
fining down of the internal combustion engine, which has done so much to
solve the problems of power in relation to weight for use with aircraft,
had not then been begun, and Maxim had nothing to guide him, so far
as work on the part of his predecessors was concerned, save the
experimental engines of Stringfellow, which, being constructed on so
small a scale in comparison with his own, afforded little guidance.
Concerning the factor of power, he says: 'When first designing this
engine, I did not know how much power I might require from it. I thought
that in some cases it might be necessary to allow the high-pressure
steam to enter the low-pressure cylinder direct, but as this would
involve a considerable loss, I constructed a species of injector. This
injector may be so adjusted that when the steam in the boiler rises
above a certain predetermined point, say 300 lbs., to the square inch,
it opens a valve and escapes past the high-pressure cylinder instead of
blowing off at the safety valve. In escaping through this valve, a fall
of about 200 lbs. pressure per square inch is made to do work on the
surrounding steam and drive it forward in the pipe, producing a pressure
on the low-pressure piston considerably higher than the back-pressure on
the high-pressure piston. In this way a portion of the work which would
otherwise be lost is utilised, and it is possible, with an unlimited
supply of steam, to cause the engines to develop an enormous amount of
power.'

With regard to boilers, Maxim writes,

'The first boiler which I made was constructed something on the
Herreshof principle, but instead of having one simple pipe in one very
long coil, I used a series of very small and light pipes, connected in
such a manner that there was a rapid circulation through the whole--the
tubes increasing in size and number as the steam was generated. I
intended that there should be a pressure of about 100 lbs. more on the
feed water end of the series than on the steam end, and I believed that
this difference in pressure would be sufficient to ensure direct and
positive circulation through every tube in the series. The first boiler
was exceedingly light, but the workmanship, as far as putting the tubes
together was concerned, was very bad, and it was found impossible to so
adjust the supply of water as to make dry steam without overheating and
destroying the tubes.

'Before making another boiler I obtained a quantity of copper tubes,
about 8 feet long, 3/8 inch external diameter, and 1/50 of an inch
thick. I subjected about 100 of these tubes to an internal pressure of
1 ton per square inch of cold kerosene oil, and as none of them leaked
I did not test any more, but commenced my experiments by placing some
of them in a white-hot petroleum fire. I found that I could evaporate
as much as 26 1/2 lbs. of water per square foot of heating surface per
hour, and that with a forced circulation, although the quantity of water
passing was very small but positive, there was no danger of overheating.
I conducted many experiments with a pressure of over 400 lbs. per square
inch, but none of the tubes failed. I then mounted a single tube in a
white-hot furnace, also with a water circulation, and found that it only
burst under steam at a pressure of 1,650 lbs. per square inch. A large
boiler, having about 800 square feet of heating surface, including the
feed-water heater, was then constructed. This boiler is about 4 1/2 feet
wide at the bottom, 8 feet long and 6 feet high. It weighs, with the
casing, the dome, and the smoke stack and connections, a little less
than 1,000 lbs. The water first passes through a system of small
tubes--1/4 inch in diameter and 1/60 inch thick--which were placed at
the top of the boiler and immediately over the large tubes.... This
feed-water heater is found to be very effective. It utilises the heat
of the products of combustion after they have passed through the boiler
proper and greatly reduces their temperature, while the feed-water
enters the boiler at a temperature of about 250 F. A forced circulation
is maintained in the boiler, the feed-water entering through a spring
valve, the spring valve being adjusted in such a manner that the
pressure on the water is always 30 lbs. per square inch in excess of
the boiler pressure. This fall of 30 lbs. in pressure acts upon the
surrounding hot water which has already passed through the tubes, and
drives it down through a vertical outside tube, thus ensuring a positive
and rapid circulation through all the tubes. This apparatus is found to
act extremely well.'

Thus Maxim, who with this engine as power for his large aeroplane
achieved free flight once, as a matter of experiment, though for what
distance or time the machine was actually off the ground is matter for
debate, since it only got free by tearing up the rails which were to
have held it down in the experiment. Here, however, was a steam engine
which was practicable for use in the air, obviously, and only the rapid
success of the internal combustion engine prevented the steam-producing
type from being developed toward perfection.

The first designers of internal combustion engines, knowing nothing
of the petrol of these days, constructed their examples with a view to
using gas as fuel. As far back as 1872 Herr Paul Haenlein obtained a
speed of about 10 miles an hour with a balloon propelled by an internal
combustion engine, of which the fuel was gas obtained from the balloon
itself. The engine in this case was of the Lenoir type, developing
some 6 horse-power, and, obviously, Haenlein's flights were purely
experimental and of short duration, since he used the gas that sustained
him and decreased the lifting power of his balloon with every stroke of
the piston of his engine. No further progress appears to have been made
with the gas-consuming type of internal combustion engine for work
with aircraft; this type has the disadvantage of requiring either a
gas-producer or a large storage capacity for the gas, either of which
makes the total weight of the power plant much greater than that of
a petrol engine. The latter type also requires less attention when
working, and the fuel is more convenient both for carrying and in the
matter of carburation.

The first airship propelled by the present-day type of internal
combustion engine was constructed by Baumgarten and Wolfert in 1879
at Leipzig, the engine being made by Daimler with a view to working on
benzine--petrol as a fuel had not then come to its own. The construction
of this engine is interesting since it was one of the first of Daimler's
make, and it was the development brought about by the experimental
series of which this engine was one that led to the success of the
motor-car in very few years, incidentally leading to that fining down of
the internal combustion engine which has facilitated the development
of the aeroplane with such remarkable rapidity. Owing to the faulty
construction of the airship no useful information was obtained from
Daimler's pioneer installation, as the vessel got out of control
immediately after it was first launched for flight, and was wrecked.
Subsequent attempts at mechanically-propelled flight by Wolfert ended,
in 1897, in the balloon being set on fire by an explosion of benzine
vapour, resulting in the death of both the aeronauts.

Daimler, from 1882 onward, devoted his attention to the perfecting of
the small, high-speed petrol engine for motor-car work, and owing to
his efforts, together with those of other pioneer engine-builders, the
motorcar was made a success. In a few years the weight of this type of
engine was reduced from near on a hundred pounds per horse-power to less
than a tenth of that weight, but considerable further improvement had to
be made before an engine suitable for use with aircraft was evolved.

The increase in power of the engines fitted to airships has made
steady progress from the outset; Haenlein's engine developed about 6
horse-power; the Santos-Dumont airship of 1898 was propelled by a motor
of 4 horse-power; in 1902 the Lebaudy airship was fitted with an engine
of 40 horse-power, while, in 1910, the Lebaudy brothers fitted an
engine of nearly 300 horsepower to the airship they were then
constructing--1,400 horse-power was common in the airships of the War
period, and the later British rigids developed yet more.

Before passing on to consideration of the petrol-driven type of engine,
it is necessary to accord brief mention to the dirigible constructed in
1884 by Gaston and Albert Tissandier, who at Grenelle, France, achieved
a directed flight in a wind of 8 miles an hour, obtaining their power
for the propeller from 1 1/3 horse-power Siemens electric motor, which
weighed 121 lbs. and took its current from a bichromate battery weighing
496 lbs. A two-bladed propeller, 9 feet in diameter, was used, and
the horse-power output was estimated to have run up to 1 1/2 as the
dirigible successfully described a semicircle in a wind of 8 miles an
hour, subsequently making headway transversely to a wind of 7 miles
an hour. The dirigible with which this motor was used was of the
conventional pointed-end type, with a length of 92 feet, diameter of 30
feet, and capacity of 37,440 cubic feet of gas. Commandant Renard, of
the French army balloon corps, followed up Tissandier's attempt in
the next year--1885--making a trip from Chalais-Meudon to Paris and
returning to the point of departure quite successfully. In this case the
motive power was derived from an electric plant of the type used by
the Tissandiers, weighing altogether 1,174 lbs., and developing
9 horsepower. A speed of 14 miles an hour was attained with this
dirigible, which had a length of 165 feet, diameter of 27 feet, and
capacity of 65,836 cubic feet of gas.

Reverting to the petrol-fed type again, it is to be noted that
Santos-Dumont was practically the first to develop the use of the
ordinary automobile engine for air work--his work is of such importance
that it has been considered best to treat of it as one whole, and
details of the power plants are included in the account of his
experiments. Coming to the Lebaudy brothers and their work, their engine
of 1902 was a 40 horse-power Daimler, four-cylindered; it was virtually
a large edition of the Daimler car engine, the arrangement of the
various details being on the lines usually adopted for the standard
Daimler type of that period. The cylinders were fully water-jacketed,
and no special attempt toward securing lightness for air work appears to
have been made.

The fining down of detail that brought weight to such limits as would
fit the engine for work with heavier-than-air craft appears to have
waited for the brothers Wright. Toward the end of 1903 they fitted
to their first practicable flying machine the engine which made the
historic first aeroplane flight; this engine developed 30 horse-power,
and weighed only about 7 lbs. per horse-power developed, its design and
workmanship being far ahead of any previous design in this respect, with
the exception of the remarkable engine, designed by Manly, installed in
Langley's ill-fated aeroplane--or 'aerodrome,' as he preferred to call
it--tried in 1903.

The light weight of the Wright brothers' engine did not necessitate a
high number of revolutions per minute to get the requisite power; the
speed was only 1,300 revolutions per minute, which, with a piston
stroke of 3.94 inches, was quite moderate. Four cylinders were used,
the cylinder diameter being 4.42 inches; the engine was of the
vertical type, arranged to drive two propellers at a rate of about 350
revolutions per minute, gearing being accomplished by means of chain
drive from crank-shaft end to propeller spindle.

The methods adopted by the Wrights for obtaining a light-weight engine
were of considerable interest, in view of the fact that the honour
of first achieving flight by means of the driven plane belongs to
them--unless Ader actually flew as he claimed. The cylinders of this
first Wright engine were separate castings of steel, and only the
barrels were jacketed, this being done by fixing loose, thin aluminium
covers round the outside of each cylinder. The combustion head and valve
pockets were cast together with the cylinder barrel, and were not water
cooled. The inlet valves were of the automatic type, arranged on the
tops of the cylinders, while the exhaust valves were also overhead,
operated by rockers and push-rods. The pistons and piston rings were
of the ordinary type, made of cast-iron, and the connecting rods were
circular in form, with a hole drilled down the middle of each to reduce
the weight.

Necessity for increasing power and ever lighter weight in relation to
the power produced has led to the evolution of a number of different
designs of internal combustion engines. It was quickly realised that
increasing the number of cylinders on an engine was a better way of
getting more power than that of increasing the cylinder diameter, as the
greater number of cylinders gives better torque-even turning effect--as
well as keeping down the weight--this latter because the bigger
cylinders must be more stoutly constructed than the small sizes; this
fact has led to the construction of engines having as many as eighteen
cylinders, arranged in three parallel rows in order to keep the length
of crankshaft within reasonable limits. The aero engine of to-day may,
roughly, be divided into four classes: these are the V type, in which
two rows of cylinders are set parallel at a certain angle to each other;
the radial type, which consists of cylinders arranged radially and
remaining stationary while the crankshaft revolves; the rotary, where
the cylinders are disposed round a common centre and revolve round
a stationary shaft, and the vertical type, of four or six
cylinders--seldom more than this--arranged in one row. A modification of
the V type is the eighteen-cylindered engine--the Sunbeam is one of the
best examples--in which three rows of cylinders are set parallel to each
other, working on a common crankshaft. The development these four types
started with that of the vertical--the simplest of all; the V, radial,
and rotary types came after the vertical, in the order given.

The evolution of the motor-car led to the adoption of the vertical
type of internal combustion engine in preference to any other, and
it followed naturally that vertical engines should be first used for
aeroplane propulsion, as by taking an engine that had been developed to
some extent, and adapting it to its new work, the problem of mechanical
flight was rendered easier than if a totally new type had had to be
evolved. It was quickly realised--by the Wrights, in fact-that the
minimum of weight per horse-power was the prime requirement for the
successful development of heavier-than-air machines, and at the same
time it was equally apparent that the utmost reliability had to be
obtained from the engine, while a third requisite was economy, in order
to reduce the weight of petrol necessary for flight.

Daimler, working steadily toward the improvement of the internal
combustion engine, had made considerable progress by the end of
last century. His two-cylinder engine of 1897 was approaching to
the present-day type, except as regards the method of ignition; the
cylinders had 3.55 inch diameter, with a 4.75 inch piston stroke,
and the engine was rated at 4.5 brake horse-power, though it probably
developed more than this in actual running at its rated speed of 800
revolutions per minute. Power was limited by the inlet and exhaust
passages, which, compared with present-day practice, were very small.
The heavy castings of which the engine was made up are accounted for by
the necessity for considering foundry practice of the time, for in 1897
castings were far below the present-day standard. The crank-case of
this two-cylinder vertical Daimler engine was the only part made of
aluminium, and even with this no attempt was made to attain lightness,
for a circular flange was cast at the bottom to form a stand for the
engine during machining and erection. The general design can be followed
from the sectional views, and these will show, too, that ignition was by
means of a hot tube on the cylinder head, which had to be heated with a
blow-lamp before starting the engine. With all its well known and hated
troubles, at that time tube ignition had an advantage over the magneto,
and the coil and accumulator system, in reliability; sparking plugs,
too, were not so reliable then as they are now. Daimler fitted a very
simple type of carburettor to this engine, consisting only of a float
with a single jet placed in the air passage. It may be said that this
twin-cylindered vertical was the first of the series from which has been
evolved the Mercedes-Daimler car and airship engines, built in sizes up
to and even beyond 240 horse-power.

In 1901 the development of the petrol engine was still so slight that it
did not admit of the construction, by any European maker, of an engine
weighing less than 12 lbs. per horse-power. Manly, working at the
instance of Professor Langley, produced a five-cylindered radial type
engine, in which both the design and workmanship showed a remarkable
advance in construction. At 950 revolutions per minute it developed 52.4
horse-power, weighing only 2.4 pounds per horse-power; it was a very
remarkable achievement in engine design, considering the power developed
in relation to the total weight, and it was, too, an interruption in
the development of the vertical type which showed that there were other
equally great possibilities in design.

In England, the first vertical aero-engine of note was that designed
by Green, the cylinder dimensions being 4.15 inch diameter by 4.75
stroke--a fairly complete idea of this engine can be obtained from the
accompanying diagrams. At a speed of 1,160 revolutions per minute
it developed 35 brake horse-power, and by accelerating up to 1,220
revolutions per minute a maximum of 40 brake horse-power could be
obtained--the first-mentioned was the rated working speed of the engine
for continuous runs. A flywheel, weighing 23.5 lbs., was fitted to the
engine, and this, together with the ignition system, brought the weight
up to 188 lbs., giving 5.4 lbs. per horse-power. In comparison with the
engine fitted to the Wrights' aeroplane a greater power was obtained
from approximately the same cylinder volume, and an appreciable saving
in weight had also been effected. The illustration shows the arrangement
of the vertical valves at the top of the cylinder and the overhead cam
shaft, while the position of the carburettor and inlet pipes can be
also seen. The water jackets were formed by thin copper casings, each
cylinder being separate and having its independent jacket rigidly
fastened to the cylinder at the top only, thus allowing for free
expansion of the casing; the joint at the bottom end was formed by
sliding the jacket over a rubber ring. Each cylinder was bolted to the
crank-case and set out of line with the crankshaft, so that the crank
has passed over the upper dead centre by the time that the piston is at
the top of its stroke when receiving the full force of fuel explosion.
The advantage of this desaxe setting is that the pressure in the
cylinder acts on the crank-pin with a more effective leverage during
that part of the stroke when that pressure is highest, and in addition
the side pressure of the piston on the cylinder wall, due to the thrust
of the connecting rod, is reduced. Possibly the charging of the cylinder
is also more complete by this arrangement, owing to the slower movement
of the piston at the bottom of its stroke allowing time for an increased
charge of mixture to enter the cylinder.

A 60 horse-power engine was also made, having four vertical cylinders,
each with a diameter of 5.5 inches and stroke of 5.75 inches, developing
its rated power at 1,100 revolutions per minute. By accelerating up to
1,200 revolutions per minute 70 brake horsepower could be obtained, and
a maximum of 80 brake horse-power was actually attained with the type.
The flywheel, fitted as with the original 35 horse-power engine, weighed
37 lbs.; with this and with the ignition system the total weight of
the engine was only 250 lbs., or 4.2 lbs. per horse-power at the normal
rating. In this design, however, low weight in relation to power was
not the ruling factor, for Green gave more attention to reliability and
economy of fuel consumption, which latter was approximately 0.6 pint of
petrol per brake horse-power per hour. Both the oil for lubricating
the bearings and the water for cooling the cylinders were circulated by
pumps, and all parts of the valve gear, etc., were completely enclosed
for protection from dust.

A later development of the Green engine was a six-cylindered vertical,
cylinder dimensions being 5.5 inch diameter by 6 inch stroke, developing
120 brake horsepower when running at 1,250 revolutions per minute. The
total weight of the engine with ignition system 398 was 440 lbs., or
3.66 lbs. per horse-power. One of these engines was used on the machine
which, in 1909, won the prize of L1,000 for the first circular mile
flight, and it may be noted, too, that S. F. Cody, making the circuit
of England in 1911, used a four-cylinder Green engine. Again, it was a
Green engine that in 1914 won the L5,000 prize offered for the best aero
engine in the Naval and Military aeroplane engine competition.

Manufacture of the Green engines, in the period of the War, had
standardised to the production of three types. Two of these were
six-cylinder models, giving respectively 100 and 150 brake horse-power,
and the third was a twelve-cylindered model rated at 275 brake
horse-power.

In 1910 J. S. Critchley compiled a list showing the types of engine then
being manufactured; twenty-two out of a total of seventy-six were of the
four-cylindered vertical type, and in addition to these there were two
six-cylindered verticals. The sizes of the four-cylinder types ranged
from 26 up to 118 brake horse-power; fourteen of them developed less
than 50 horse-power, and only two developed over 100 horse-power.

It became apparent, even in the early stages of heavier-than-air flying,
that four-cylinder engines did not produce the even torque that was
required for the rotation of the power shaft, even though a flywheel
was fitted to the engine. With this type of engine the breakage of
air-screws was of frequent occurrence, and an engine having a more
regular rotation was sought, both for this and to avoid the excessive
vibration often experienced with the four-cylinder type. Another, point
that forced itself on engine builders was that the increased power which
was becoming necessary for the propulsion of aircraft made an increase
in the number of cylinders essential, in order to obtain a light engine.
An instance of the weight reduction obtainable in using six cylinders
instead of four is shown in Critchley's list, for one of the
four-cylinder engines developed 118.5 brake horse-power and weighed
1,100 lbs., whereas a six-cylinder engine by the same manufacturer
developed 117.5 brake horse-power with a weight of 880 lbs., the
respective cylinder dimensions being 7.48 diameter by 9.06 stroke
for the four-cylinder engine, and 6.1 diameter by 7.28 stroke for the
six-cylinder type.

A list of aeroplane engines, prepared in 1912 by Graham Clark, showed
that, out of the total number of 112 engines then being manufactured,
forty-two were of the vertical type, and of this number twenty-four had
four-cylinders while sixteen were six-cylindered. The German aeroplane
engine trials were held a year later, and sixty-six engines entered the
competition, fourteen of these being made with air-cooled cylinders.
All of the ten engines that were chosen for the final trials were of the
water-cooled type, and the first place was won by a Benz four-cylinder
vertical engine which developed 102 brake horse-power at 1,288
revolutions per minute. The cylinder dimensions of this engine were 5.1
inch diameter by 7.1 inch stroke, and the weight of the engine worked
out at 3.4 lbs. per brake horse-power. During the trials the full-load
petrol consumption was 0.53 pint per horse-power per hour, and the
amount of lubricating oil used was 0.0385 pint per brake horse-power per
hour. In general construction this Benz engine was somewhat similar to
the Green engine already described; the overhead valves, fitted in the
tops of the cylinders, were similarly arranged, as was the cam-shaft;
two springs were fitted to each of the valves to guard against the
possibility of the engine being put out of action by breakage of one
of the springs, and ignition was obtained by two high-tension magnetos
giving simultaneous sparks in each cylinder by means of two sparking
plugs--this dual ignition reduced the possibility of ignition troubles.
The cylinder jackets were made of welded sheet steel so fitted around
the cylinder that the head was also water-cooled, and the jackets were
corrugated in the middle to admit of independent expansion. Even the
lubrication system was duplicated, two sets of pumps being used, one to
circulate the main supply of lubricating oil, and the other to give a
continuous supply of fresh oil to the bearings, so that if the
supply from one pump failed the other could still maintain effective
lubrication.

Development of the early Daimler type brought about the four-cylinder
vertical Mercedes-Daimler engine of 85 horse-power, with cylinders
of 5.5 diameter with 5.9 inch stroke, the cylinders being cast in two
pairs. The overhead arrangement of valves was adopted, and in later
designs push-rods were eliminated, the overhead cam-shaft being adopted
in their place. By 1914 the four-cylinder Mercedes-Daimler had been
partially displaced from favour by a six-cylindered model, made in two
sizes; the first of these gave a nominal brake horse-power of 80, having
cylinders of 4.1 inches diameter by 5.5 inches stroke; the second type
developed 100 horse-power with cylinders 4.7 inches in diameter and 5.5
inches stroke, both types being run at 1,200 revolutions per minute. The
cylinders of both these types were cast in pairs, and, instead of the
water jackets forming part of the casting, as in the design of the
original four-cylinder Mercedes-Daimler engine, they were made of steel
welded to flanges on the cylinders. Steel pistons, fitted with cast-iron
rings, were used, and the overhead arrangement of valves and cam-shaft
was adopted. About 0.55 pint per brake horse-power per hour was the
usual fuel consumption necessary to full load running, and the engine
was also economical as regards the consumption of lubricating oil,
the lubricating system being 'forced' for all parts, including the
cam-shaft. The shape of these engines was very well suited for work
with aircraft, being narrow enough to admit of a streamline form being
obtained, while all the accessories could be so mounted as to produce
little or no wind resistance, and very little obstruction to the pilot's
view.

The eight-cylinder Mercedes-Daimler engine, used for airship propulsion
during the War, developed 240 brake horse-power at 1,100 revolutions per
minute; the cylinder dimensions were 6.88 diameter by 6.5 stroke--one
of the instances in which the short stroke in relation to bore was very
noticeable.

Other instances of successful vertical design-the types already detailed
are fully sufficient to give particulars of the type generally--are
the Panhard, Chenu, Maybach, N.A.G., Argus, Mulag, and the well-known
Austro-Daimler, which by 1917 was being copied in every combatant
country. There are also the later Wright engines, and in America
the Wisconsin six-cylinder vertical, weighing well under 4 lbs. per
horse-power, is evidence of the progress made with this first type of
aero engine to develop.




II. THE VEE TYPE

An offshoot from the vertical type, doubling the power of this with only
a very slight--if any--increase in the length of crankshaft, the Vee
or diagonal type of aero engine leaped to success through the insistent
demand for greater power. Although the design came after that of the
vertical engine, by 1910, according to Critchley's list of aero engines,
there were more Vee type engines being made than any other type,
twenty-five sizes being given in the list, with an average rating of
57.4 brake horse-power.

The arrangement of the cylinders in Vee form over the crankshaft,
enabling the pistons of each pair of opposite cylinders to act upon the
same crank pin, permits of a very short, compact engine being built, and
also permits of reduction of the weight per horsepower, comparing this
with that of the vertical type of engine, with one row of cylinders.
Further, at the introduction of this type of engine it was seen that
crankshaft vibration, an evil of the early vertical engines, was
practically eliminated, as was the want of longitudinal stiffness that
characterised the higher-powered vertical engines.

Of the Vee type engines shown in Critchley's list in 1910 nineteen
different sizes were constructed with eight cylinders, and with
horse-powers ranging from thirty to just over the hundred; the lightest
of these weighed 2.9 lbs. per horse-power--a considerable advance in
design on the average vertical engine, in this respect of weight per
horse-power. There were also two sixteen-cylinder engines of Vee design,
the larger of which developed 134 horse-power with a weight of only 2
lbs. per brake horse-power. Subsequent developments have indicated that
this type, with the further development from it of the double-Vee, or
engine with three rows of cylinders, is likely to become the standard
design of aero engine where high powers are required. The construction
permits of placing every part so that it is easy of access, and the
form of the engine implies very little head resistance, while it can be
placed on the machine--supposing that machine to be of the single-engine
type--in such a way that the view of the pilot is very little obstructed
while in flight.

An even torque, or great uniformity of rotation, is transmitted to the
air-screw by these engines, while the design also permits of such good
balance of the engine itself that vibration is practically eliminated.
The angle between the two rows of cylinders is varied according to the
number of cylinders, in order to give working impulses at equal angles
of rotation and thus provide even torque; this angle is determined by
dividing the number of degrees in a circle by the number of cylinders
in either row of the engine. In an eight-cylindered Vee type engine, the
angle between the cylinders is 90 degrees; if it is a twelve-cylindered
engine, the angle drops to 60 degrees.

One of the earliest of the British-built Vee type engines was an
eight-cylinder 50 horse-power by the Wolseley Company, constructed in
1908 with a cylinder bore of 3.75 inches and stroke of 5 inches, running
at a normal speed of 1,350 revolutions per minute. With this engine, a
gearing was introduced to enable the propeller to run at a lower speed
than that of the engine, the slight loss of efficiency caused by the
friction of the gearing being compensated by the slower speed of the
air-screw, which had higher efficiency than would have been the case if
it had been run at the engine speed. The ratio of the gearing--that is,
the speed of the air-screw relatively to that of the engine, could be
chosen so as to suit exactly the requirements of the air-screw, and the
gearing itself, on this engine, was accomplished on the half-speed shaft
actuating the valves.

Very soon after this first design had been tried out, a second Vee type
engine was produced which, at 1,200 revolutions per minute, developed 60
horse-power; the size of this engine was practically identical with that
of its forerunner, the only exception being an increase of half an inch
in the cylinder stroke--a very long stroke of piston in relation to
the bore of the cylinder. In the first of these two engines, which was
designed for airship propulsion, the weight had been about 8 lbs. per
brake horse-power, no special attempt appearing to have been made to
fine down for extreme lightness; in this 60 horse-power design, the
weight was reduced to 6.1 lbs. per horse-power, counting the latter
as normally rated; the engine actually gave a maximum of 75 brake
horse-power, reducing the ratio of weight to power very considerably
below the figure given.

The accompanying diagram illustrates a later Wolseley model, end
elevation, the eight-cylindered 120 horse-power Vee type aero engine
of the early war period. With this engine, each crank pin has two
connecting rods bearing on it, these being placed side by side and
connected to the pistons of opposite cylinders and the two cylinders of
the pair are staggered by an amount equal to the width of the connecting
rod bearing, to afford accommodation for the rods. The crankshaft was a
nickel chrome steel forging, machined hollow, with four crank pins set
at 180 degrees to each other, and carried in three bearings lined with
anti-friction metal. The connecting rods were made of tubular nickel
chrome steel, and the pistons of drawn steel, each being fitted with
four piston rings. Of these the two rings nearest to the piston head
were of the ordinary cast-iron type, while the others were of phosphor
bronze, so arranged as to take the side thrust of the piston. The
cylinders were of steel, arranged in two groups or rows of four, the
angular distance between them being 90 degrees. In the space above the
crankshaft, between the cylinder rows, was placed the valve-operating
mechanism, together with the carburettor and ignition system, thus
rendering this a very compact and accessible engine. The combustion
heads of the cylinders were made of cast-iron, screwed into the steel
cylinder barrels; the water-jacket was of spun aluminium, with one end
fitting over the combustion head and the other free to slide on the
cylinder; the water-joint at the lower end was made tight by a Dermatine
ring carried between small flanges formed on the cylinder barrel.
Overhead valves were adopted, and in order to make these as large as
possible the combustion chamber was made slightly larger in diameter
than the cylinder, and the valves set at an angle. Dual ignition was
fitted in each cylinder, coil and accumulator being used for starting
and as a reserve in case of failure of the high-tension magneto system
fitted for normal running. There was a double set of lubricating pumps,
ensuring continuity of the oil supply to all the bearings of the engine.

The feature most noteworthy in connection with the running of this type
of engine was its flexibility; the normal output of power was
obtained with 1,150 revolutions per minute of the crankshaft, but, by
accelerating up to 1,400 revolutions, a maximum of 147 brake horse-power
could be obtained. The weight was about 5 lbs. per horse-power, the
cylinder dimensions being 5 inches bore by 7 inches stroke. Economy in
running was obtained, the fuel consumption being 0.58 pint per brake
horse-power per hour at full load, with an expenditure of about 0.075
pint of lubricating oil per brake horse-power per hour.

Another Wolseley Vee type that was standardised was a 90 horse-power
eight-cylinder engine running at 1,800 revolutions per minute, with
a reducing gear introduced by fitting the air screw on the half-speed
shaft. First made semi-cooled--the exhaust valve was left air-cooled,
and then entirely water-jacketed--this engine demonstrated the advantage
of full water cooling, for under the latter condition the same power was
developed with cylinders a quarter of an inch less in diameter than in
the semi-cooled pattern; at the same time the weight was brought down to
4 1/2 lbs. per horsepower.

A different but equally efficient type of Vee design was the Dorman
engine, of which an end elevation is shown; this developed 80 brake
horse-power at a speed of 1,300 revolutions per minute, with a cylinder
bore of 5 inches; each cylinder was made in cast-iron in one piece with
the combustion chamber, the barrel only being water-jacketed. Auxiliary
exhaust ports were adopted, the holes through the cylinder wall being
uncovered by the piston at the bottom of its stroke--the piston, 4.75
inches in length, was longer than its stroke, so that these ports were
covered when it was at the top of the cylinder. The exhaust discharged
through the ports into a belt surrounding the cylinder, the belts on the
cylinders being connected so that the exhaust gases were taken through
a single pipe. The air was drawn through the crank case, before reaching
the carburettor, this having the effect of cooling the oil in the crank
case as well as warming the air and thus assisting in vaporising the
petrol for each charge of the cylinders. The inlet and exhaust valves
were of the overhead type, as may be gathered from the diagram, and in
spite of cast-iron cylinders being employed a light design was obtained,
the total weight with radiator, piping, and water being only 5.5 lbs.
per horse-power.

Here was the antithesis of the Wolseley type in the matter of bore in
relation to stroke; from about 1907 up to the beginning of the war, and
even later, there was controversy as to which type--that in which the
bore exceeded the stroke, or vice versa--gave greater efficiency.
The short-stroke enthusiasts pointed to the high piston speed of the
long-stroke type, while those who favoured the latter design contended
that full power could not be obtained from each explosion in the
short-stroke type of cylinder. It is now generally conceded that the
long-stroke engine yields higher efficiency, and in addition to this,
so far as car engines are concerned, the method of rating horse-power
in relation to bore without taking stroke into account has given the
long-stroke engine an advantage, actual horse-power with a long stroke
engine being in excess of the nominal rating. This may have had some
influence on aero engine design, but, however this may have been, the
long-stroke engine has gradually come to favour, and its rival has taken
second place.

For some time pride of place among British Vee type engines was held
by the Sunbeam Company, which, owing to the genius of Louis Coatalen,
together with the very high standard of construction maintained by the
firm, achieved records and fame in the middle and later periods of the
war. Their 225 horse-power twelve-cylinder engine ran at a normal
speed of 2,000 revolutions per minute; the air screw was driven through
gearing at half this speed, its shaft being separate from the timing
gear and carried in ball-bearings on the nose-piece of the engine. The
cylinders were of cast-iron, entirely water-cooled; a thin casing formed
the water-jacket, and a very light design was obtained, the weight being
only 3.2 lbs. per horse-power. The first engine of Sunbeam design had
eight cylinders and developed 150 horse-power at 2,000 revolutions
per minute; the final type of Vee design produced during the war was
twelve-cylindered, and yielded 310 horse-power with cylinders 4.3 inches
bore by 6.4 inches stroke. Evidence in favour of the long-stroke engine
is afforded in this type as regards economy of working; under full load,
working at 2,000 revolutions per minute, the consumption was 0.55 pints
of fuel per brake horse-power per hour, which seems to indicate that the
long stroke permitted of full use being made of the power resulting from
each explosion, in spite of the high rate of speed of the piston.

Developing from the Vee type, the eighteen-cylinder 475 brake
horse-power engine, designed during the war, represented for a time
the limit of power obtainable from a single plant. It was water-cooled
throughout, and the ignition to each cylinder was duplicated; this
engine proved fully efficient, and economical in fuel consumption.
It was largely used for seaplane work, where reliability was fully as
necessary as high power.

The abnormal needs of the war period brought many British firms into the
ranks of Vee-type engine-builders, and, apart from those mentioned,
the most notable types produced are the Rolls-Royce and the Napier.
The first mentioned of these firms, previous to 1914 had concentrated
entirely on car engines, and their very high standard of production in
this department of internal combustion engine work led, once they took
up the making of aero engines, to extreme efficiency both of design and
workmanship. The first experimental aero engine, of what became known
as the 'Eagle' type, was of Vee design--it was completed in March
of 1915--and was so successful that it was standardised for quantity
production. How far the original was from the perfection subsequently
ascertained is shown by the steady increase in developed horse-power
of the type; originally designed to develop 200 horse-power, it was
developed and improved before its first practical trial in October of
1915, when it developed 255 horsepower on a brake test. Research
and experiment produced still further improvements, for, without any
enlargement of the dimensions, or radical alteration in design, the
power of the engine was brought up to 266 horse-power by March of 1916,
the rate of revolutions of 1,800 per minute being maintained throughout.
July, 1916 gave 284 horse-power; by the cud of the year this had been
increased to 322 horse-power; by September of 1917 the increase was to
350 horse-power, and by February of 1918 then 'Eagle' type of engine was
rated at 360 horse-power, at which standard it stayed. But there is no
more remarkable development in engine design than this, a 75 per cent
increase of power in the same engine in a period of less than three
years.

To meet the demand for a smaller type of engine for use on training
machines, the Rolls-Royce firm produced the 'Hawk' Vee-type engine of
100 horsepower, and, intermediately between this and the 'Eagle,' the
'Falcon' engine came to being with an original rated horse-power of 205
at 1,800 revolutions per minute, in April of 1916. Here was another case
of growth of power in the same engine through research, almost similar
to that of the 'Eagle' type, for by July of 1918 the 'Falcon' was
developing 285 horse-power with no radical alteration of design.
Finally, in response to the constant demand for increase of power in a
single plant, the Rolls-Royce company designed and produced the 'Condor'
type of engine, which yielded 600 horse-power on its first test in
August of 1918. The cessation of hostilities and consequent falling off
in the demand for extremely high-powered plants prevented the 'Condor'
being developed to its limit, as had been the 'Falcon' and 'Eagle'
types.

The 'Eagle 'engine was fitted to the two Handley-Page aeroplanes--which
made flights from England to India--it was virtually standard on the
Handley-Page bombers of the later War period, though to a certain extent
the American 'Liberty' engine was also used. Its chief record, however,
is that of being the type fitted to the Vickers-Vimy aeroplane which
made the first Atlantic flight, covering the distance of 1,880 miles at
a speed averaging 117 miles an hour.

The Napier Company specialised on one type of engine from the outset,
a power plant which became known as the 'Lion' engine, giving 450
horse-power with twelve cylinders arranged in three rows of four each.
Considering the engine as 'dry,' or without fuel and accessories, an
abnormally light weight per horse-power--only 1.89 lbs.--was attained
when running at the normal rate of revolution. The cylinders and
water-jackets are of steel, and there is fitted a detachable aluminium
cylinder head containing inlet and exhaust valves and valve actuating
mechanism; pistons are of aluminium alloy, and there are two inlet and
two exhaust valves to each cylinder, the whole of the valve mechanism
being enclosed in an oil-tight aluminium case. Connecting rods and
crankshaft are of steel, the latter being machined from a solid steel
forging and carried in five roller bearings and one plain bearing at the
forward end. The front end of the crank-case encloses reduction gear for
the propeller shaft, together with the shaft and bearings. There are
two suction and one pressure type oil pumps driven through gears at
half-engine speed, and two 12 spark magnetos, giving 2 sparks in each
cylinder.

The cylinders are set with the central row vertical, and the two side
rows at angles of 60 degrees each; cylinder bore is 5 1/2 inches, and
stroke 5 1/8 inches; the normal rate of revolution is 1,350 per minute,
and the reducing gear gives one revolution of the propeller shaft to
1.52 revolutions of crankshaft. Fuel consumption is 0.48lbs. of fuel per
brake horse-power hour at full load, and oil consumption is 0.020 lbs.
per brake horsepower hour. The dry weight of the engine, complete with
propeller boss, carburettors, and induction pipes, is 850 lbs., and the
gross weight in running order, with fuel and oil for six hours working,
is 2,671 lbs., exclusive of cooling water.

To this engine belongs an altitude record of 30,500 feet, made at
Martlesham, near Ipswich, on January 2nd, 1919, by Captain Lang, R.A.F.,
the climb being accomplished in 66 minutes 15 seconds. Previous to this,
the altitude record was held by an Italian pilot, who made 25,800 feet
in an hour and 57 minutes in 1916. Lang's climb was stopped through
the pressure of air, at the altitude he reached, being insufficient for
driving the small propellers on the machine which worked the petrol and
oil pumps, or he might have made the height said to have been attained
by Major Schroeder on February 27th, 1920, at Dayton, Ohio. Schroeder
is said to have reached an altitude of 36,020 feet on a Napier biplane,
and, owing to failure of the oxygen supply, to have lost consciousness,
fallen five miles, righted his machine when 2,000 feet in the air, and
alighted successfully. Major Schroeder is an American.

Turning back a little, and considering other than British design of Vee
and double-Vee or 'Broad arrow' type of engine, the Renault firm from
the earliest days devoted considerable attention to the development of
this type, their air-cooled engines having been notable examples from
the earliest days of heavier-than-air machines. In 1910 they were making
three sizes of eight-cylindered Vee-type engines, and by 1915 they had
increased to the manufacture of five sizes, ranging from 25 to 100 brake
horse-power, the largest of the five sizes having twelve cylinders but
still retaining the air-cooled principle. The De Dion firm, also,
made Vee-type engines in 1914, being represented by an 80 horse-power
eight-cylindered engine, air-cooled, and a 150 horse-power, also
of eight cylinders, water-cooled, running at a normal rate of 1,600
revolutions per minute. Another notable example of French construction
was the Panhard and Levassor 100 horse-power eight-cylinder Vee engine,
developing its rated power at 1,500 revolutions per minute, and having
the--for that time--low weight of 4.4 lbs. per horse-power.

American Vee design has followed the British fairly cclosely; the
Curtiss Company produced originally a 75 horse-power eight-cylinder Vee
type running at 1,200 revolutions per minute, supplementing this with
a 170 horse-power engine running at 1,600 revolutions per minute, and
later with a twelve-cylinder model Vee type, developing 300 horse-power
at 1,500 revolutions per minute, with cylinder bore of 5 inches and
stroke of 7 inches. An exceptional type of American design was the Kemp
Vee engine of 80 horse-power in which the cylinders were cooled by a
current of air obtained from a fan at the forward end of the engine.
With cylinders of 4.25 inches bore and 4.75 inches stroke, the rater
power was developed at 1,150 revolutions per minute, and with the engine
complete the weight was only 4.75 lbs. per horse-power.




III. THE RADIAL TYPE

The very first successful design of internal combustion aero engine made
was that of Charles Manly, who built a five-cylinder radial engine in
1901 for use with Langley's 'aerodrome,' as the latter inventor decided
to call what has since become known as the aeroplane. Manly made a
number of experiments, and finally decided on radial design, in which
the cylinders are so rayed round a central crank-pin that the pistons
act successively upon it; by this arrangement a very short and compact
engine is obtained, with a minimum of weight, and a regular crankshaft
rotation and perfect balance of inertia forces.

When Manly designed his radial engine, high speed internal combustion
engines were in their infancy, and the difficulties in construction
can be partly realised when the lack of manufacturing methods for this
high-class engine work, and the lack of experimental data on the various
materials, are taken into account. During its tests, Manly's engine
developed 52.4 brake horsepower at a speed of 950 revolutions per
minute, with the remarkably low weight of only 2.4 lbs. per horsepower;
this latter was increased to 3.6 lbs. when the engine was completed
by the addition of ignition system, radiator, petrol tank, and all
accessories, together with the cooling water for the cylinders.

In Manly's engine, the cylinders were of steel, machined outside and
inside to 1/16 of an inch thickness; on the side of cylinder, at the top
end, the valve chamber was brazed, being machined from a solid forging,
The casing which formed the water-jacket was of sheet steel, 1/50 of an
inch in thickness, and this also was brazed on the cylinder and to
the valve chamber. Automatic inlet valves were fitted, and the exhaust
valves were operated by a cam which had two points, 180 degrees
apart; the cam was rotated in the opposite direction to the engine at
one-quarter engine speed. Ignition was obtained by using a one-spark
coil and vibrator for all cylinders, with a distributor to select
the right cylinder for each spark--this was before the days of the
high-tension magneto and the almost perfect ignition systems that makers
now employ. The scheme of ignition for this engine was originated by
Manly himself, and he also designed the sparking plugs fitted in the
tops of the cylinders. Through fear of trouble resulting if the steel
pistons worked on the steel cylinders, cast iron liners were introduced
in the latter, 1/16 of an inch thick.

The connecting rods of this engine were of virtually the same type as is
employed on nearly all modern radial engines. The rod for one cylinder
had a bearing along the whole of the crank pin, and its end enclosed the
pin; the other four rods had bearings upon the end of the first rod,
and did not touch the crank pin. The accompanying diagram shows this
construction, together with the means employed for securing the ends of
the four rods--the collars were placed in position after the rods had
been put on. The bearings of these rods did not receive any of the
rubbing effect due to the rotation of the crank pin, the rubbing on them
being only that of the small angular displacement of the rods during
each revolution; thus there was no difficulty experienced with the
lubrication.

Another early example of the radial type of engine was the French
Anzani, of which type one was fitted to the machine with which Bleriot
first crossed the English Channel--this was of 25 horse-power. The
earliest Anzani engines were of the three-cylinder fan type, one
cylinder being vertical, and the other two placed at an angle of 72
degrees on each side, as the possibility of over-lubrication of the
bottom cylinders was feared if a regular radial construction were
adopted. In order to overcome the unequal balance of this type, balance
weights were fitted inside the crank case.

The final development of this three-cylinder radial was the 'Y' type of
engine, in which the cylinders were regularly disposed at 120 degrees
apart, the bore was 4.1, stroke 4.7 inches, and the power developed was
30 brake horse-power at 1,300 revolutions per minute.

Critchley's list of aero engines being constructed in 1910 shows twelve
of the radial type, with powers of between 14 and 100 horse-power, and
with from three to ten cylinder--this last is probably the greatest
number of cylinders that can be successfully arranged in circular form.
Of the twelve types of 1910, only two were water-cooled, and it is to be
noted that these two ran at the slowest speeds and had the lowest weight
per horse-power of any.

The Anzani radial was considerably developed special attention being
paid to this type by its makers and by 1914 the Anzani list comprised
seven different sizes of air-cooled radials. Of these the largest had
twenty cylinders, developing 200 brake horse-power--it was virtually
a double radial--and the smallest was the original 30 horse-power
three-cylinder design. A six-cylinder model was formed by a combination
of two groups of three cylinders each, acting upon a double-throw
crankshaft; the two crank pins were set at 180 degrees to each other,
and the cylinder groups were staggered by an amount equal to the
distance between the centres of the crank pins. Ten-cylinder radial
engines are made with two groups of five cylinders acting upon two
crank pins set at 180 degrees to each other, the largest Anzani 'ten'
developed 125 horsepower at 1,200 revolutions per minute, the ten
cylinders being each 4.5 inches in bore with stroke of 5.9 inches, and
the weight of the engine being 3.7 lbs. per horse-power. In the 200
horse-power Anzani radial the cylinders are arranged in four groups of
five each, acting on two crank pins. The bore of the cylinders in this
engine is the same as in the three-cylinder, but the stroke is increased
to 5.5 inches. The rated power is developed at 1,300 revolutions per
minute, and the engine complete weighs 3.4 lbs. per horse-power.

With this 200 horse-power Anzani, a petrol consumption of as low as 0.49
lbs. of fuel per brake horse-power per hour has been obtained, but
the consumption of lubricating oil is compensatingly high, being up to
one-fifth of the fuel used. The cylinders are set desaxe with the
crank shaft, and are of cast-iron, provided with radiating ribs for
air-cooling; they are attached to the crank case by long bolts passing
through bosses at the top of the cylinders, and connected to other bolts
at right angles through the crank case. The tops of the cylinders are
formed flat, and seats for the inlet and exhaust valves are formed on
them. The pistons are cast-iron, fitted with ordinary cast-iron spring
rings. An aluminium crank case is used, being made in two halves
connected together by bolts, which latter also attach the engine to the
frame of the machine. The crankshaft is of nickel steel, made hollow,
and mounted on ball-bearings in such a manner that practically a
combination of ball and plain bearings is obtained; the central web
of the shaft is bent to bring the centres of the crank pins as close
together as possible, leaving only room for the connecting rods, and
the pins are 180 degrees apart. Nickel steel valves of the cone-seated,
poppet type are fitted, the inlet valves being automatic, and those for
the exhaust cam-operated by means of push-rods. With an engine having
such a number of cylinders a very uniform rotation of the crankshaft is
obtained, and in actual running there are always five of the cylinders
giving impulses to the crankshaft at the same time.

An interesting type of pioneer radial engine was the Farcot, in which
the cylinders were arranged in a horizontal plane, with a vertical
crankshaft which operated the air-screw through bevel gearing. This was
an eight-cylinder engine, developing 64 horse-power at 1,200 revolutions
per minute. The R.E.P. type,in the early days, was a 'fan' engine,
but the designer, M. Robert Pelterie, turned from this design to a
seven-cylinder radial, which at 1,100 revolutions per minute gave 95
horse-power. Several makers entered into radial engine development in
the years immediately preceding the War, and in 1914 there were
some twenty-two different sizes and types, ranging from 30 to 600
horse-power, being made, according to report; the actual construction of
the latter size at this time, however, is doubtful.

Probably the best example of radial construction up to the outbreak of
War was the Salmson (Canton-Unne) water-cooled, of which in 1914
six sizes were listed as available. Of these the smallest was a
seven-cylinder 90 horse-power engine, and the largest, rated at 600
horse-power, had eighteen cylinders. These engines, during the War, were
made under license by the Dudbridge Ironworks in Great Britain.

The accompanying diagram shows the construction of the cylinders in the
200 horse-power size, showing the method of cooling, and the arrangement
of the connecting rods. A patent planetary gear, also shown in the
diagram, gives exactly the same stroke to all the pistons. The complete
engine has fourteen cylinders, of forged steel machined all over, and
so secured to the crank case that any one can be removed without parting
the crank case. The water-jackets are of spun copper, brazed on to the
cylinder, and corrugated so as to admit of free expansion; the water is
circulated by means of a centrifugal pump. The pistons are of cast-iron,
each fitted with three rings, and the connecting rods are of high grade
steel, machined all over and fitted with bushes of phosphor bronze;
these rods are connected to a central collar, carried on the crank pin
by two ball-bearings. The crankshaft has a single throw, and is made
in two parts to allow the cage for carrying the big end-pins of the
connecting rods to be placed in position.

The casing is in two parts, on one of which the brackets for fixing the
engine are carried, while the other part carries the valve-gear. Bolts
secure the two parts together. The mechanically-operated steel valves
on the cylinders are each fitted with double springs and the valves are
operated by rods and levers. Two Zenith carburettors are fitted on the
rear half of the crank case, and short induction pipes are led to each
cylinder; each of the carburettors is heated by the exhaust gases.
Ignition is by two high-tension magnetos, and a compressed air
self-starting arrangement is provided. Two oil pumps are fitted for
lubricating purposes, one of which forces oil to the crankshaft and
connecting-rod bearings, while the second forces oil to the valve gear,
the cylinders being so arranged that the oil which flows along the walls
cannot flood the lower cylinders. This engine operates upon a six-stroke
cycle, a rather rare arrangement for internal combustion engines of the
electrical ignition type; this is done in order to obtain equal angular
intervals for the working impulses imparted to the rotating crankshaft,
as the cylinders are arranged in groups of seven, and all act upon the
one crankshaft. The angle, therefore, between the impulses is 77 1/7
degrees. A diagram is inset giving a side view of the engine, in order
to show the grouping of the cylinders.

The 600 horse-power Salmson engine was designed with a view to fitting
to airships, and was in reality two nine-cylindered engines, with a
gear-box connecting them; double air-screws were fitted, and these were
so arranged that either or both of them might be driven by either or
both engines; in addition to this, the two engines were complete and
separate engines as regards carburation and ignition, etc., so that
they could be run independently of each other. The cylinders were
exceptionally 'long stroke,' being 5.9 inches bore to 8.27 inches
stroke, and the rated power was developed at 1,200 revolutions per
minute, the weight of the complete engine being only 4.1 lbs. per
horse-power at the normal rating.

A type of engine specially devised for airship propulsion is that in
which the cylinders are arranged horizontally instead of vertically, the
main advantages of this form being the reduction of head resistance and
less obstruction to the view of the pilot. A casing, mounted on the top
of the engine, supports the air-screw, which is driven through bevel
gearing from the upper end of the crankshaft. With this type of engine
a better rate of air-screw efficiency is obtained by gearing the screw
down to half the rate of revolution of the engine, this giving a more
even torque. The petrol consumption of the type is very low, being only
0.48 lbs. per horse-power per hour, and equal economy is claimed as
regards lubricating oil, a consumption of as little as 0.04 lbs. per
horse-power per hour being claimed.

Certain American radial engines were made previous to 1914, the
principal being the Albatross six-cylinder engines of 50 and 100
horse-powers. Of these the smaller size was air-cooled, with cylinders
of 4.5 inches bore and 5 inches stroke, developing the rated power
at 1,230 revolutions per minute, with a weight of about 5 lbs. per
horse-power. The 100 horse-power size had cylinders of 5.5 inches bore,
developing its rated power at 1,230 revolutions per minute, and weighing
only 2.75 lbs. per horse-power. This engine was markedly similar to the
six-cylindered Anzani, having all the valves mechanically operated, and
with auxiliary exhaust ports at the bottoms of the cylinders, overrun
by long pistons. These Albatross engines had their cylinders arranged in
two groups of three, with each group of three pistons operating on one
of two crank pins, each 180 degrees apart.

The radial type of engine, thanks to Charles Manly, had the honour of
being first in the field as regards aero work. Its many advantages,
among which may be specially noted the very short crankshaft as compared
with vertical, Vee, or 'broad arrow' type of engine, and consequent
greater rigidity, ensure it consideration by designers of to-day, and
render it certain that the type will endure. Enthusiasts claim that the
'broad arrow' type, or Vee with a third row of cylinders inset between
the original two, is just as much a development from the radial engine
as from the vertical and resulting Vee; however this may be, there is
a place for the radial type in air-work for as long as the internal
combustion engine remains as a power plant.




IV. THE ROTARY TYPE

M. Laurent Seguin, the inventor of the Gnome rotary aero engine,
provided as great a stimulus to aviation as any that was given anterior
to the war period, and brought about a great advance in mechanical
flight, since these well-made engines gave a high-power output for their
weight, and were extremely smooth in running. In the rotary design the
crankshaft of the engine is stationary, and the cylinders, crank
case, and all their adherent parts rotate; the working is thus exactly
opposite in principle to that of the radial type of aero engine, and
the advantage of the rotary lies in the considerable flywheel effect
produced by the revolving cylinders, with consequent evenness of torque.
Another advantage is that air-cooling, adopted in all the Gnome engines,
is rendered much more effective by the rotation of the cylinders, though
there is a tendency to distortion through the leading side of each
cylinder being more efficiently cooled than the opposite side; advocates
of other types are prone to claim that the air resistance to the
revolving cylinders absorbs some 10 per cent of the power developed by
the rotary engine, but that has not prevented the rotary from attaining
to great popularity as a prime mover.

There were, in the list of aero engines compiled in 1910, five rotary
engines included, all air-cooled. Three of these were Gnome engines, and
two of the make known as 'International.' They ranged from 21.5 to 123
horse-power, the latter being rated at only 1.8 lbs. weight per brake
horse-power, and having fourteen cylinders, 4.33 inches in diameter
by 4.7 inches stroke. By 1914 forty-three different sizes and types
of rotary engine were being constructed, and in 1913 five rotary type
engines were entered for the series of aeroplane engine trials held
in Germany. Minor defects ruled out four of these, and only the
German Bayerischer Motoren Flugzeugwerke completed the seven-hour test
prescribed for competing engines. Its large fuel consumption barred this
engine from the final trials, the consumption being some 0.95 pints
per horse-power per hour. The consumption of lubricating oil, also was
excessive, standing at 0.123 pint per horse-power per hour. The engine
gave 37.5 effective horse-power during its trial, and the loss due to
air resistance was 4.6 horse-power, about 11 per cent. The accompanying
drawing shows the construction of the engine, in which the seven
cylinders are arranged radially on the crank case; the method of
connecting the pistons to the crank pins can be seen. The mixture is
drawn through the crank chamber, and to enter the cylinder it passes
through the two automatic valves in the crown of the piston; the exhaust
valves are situated in the tops of the cylinders, and are actuated by
cams and push-rods. Cooling of the cylinder is assisted by the radial
rings, and the diameter of these rings is increased round the hottest
part of the cylinder. When long flights are undertaken the advantage of
the light weight of this engine is more than counterbalanced by its high
fuel and lubricating oil consumption, but there are other makes which
are much better than this seven-cylinder German in respect of this.

Rotation of the cylinders in engines of this type is produced by the
side pressure of the pistons on the cylinder walls, and in order to
prevent this pressure from becoming abnormally large it is necessary
to keep the weight of the piston as low as possible, as the pressure is
produced by the tangential acceleration and retardation of the piston.
On the upward stroke the circumferential velocity of the piston is
rapidly increased, which causes it to exert a considerable tangential
pressure on the side of the cylinder, and on the return stroke there
is a corresponding retarding effect due to the reduction of the
circumferential velocity of the piston. These side pressures cause an
appreciable increase in the temperatures of the cylinders and pistons,
which makes it necessary to keep the power rating of the engines fairly
low.

Seguin designed his first Gnome rotary as a 34 horse-power engine when
run at a speed of 1,300 revolutions per minute. It had five cylinders,
and the weight was 3.9 lbs. per horse-power. A seven-cylinder model soon
displaced this first engine, and this latter, with a total weight of 165
lbs., gave 61.5 horse-power. The cylinders were machined out of solid
nickel chrome-steel ingots, and the machining was carried out so that
the cylinder walls were under 1/6 of an inch in thickness. The pistons
were cast-iron, fitted each with two rings, and the automatic inlet
valve to the cylinder was placed in the crown of the piston. The
connecting rods, of 'H' section, were of nickel chrome-steel, and the
large end of one rod, known as the 'master-rod' embraced the crank pin;
on the end of this rod six hollow steel pins were carried, and to these
the remaining six connecting-rods were attached. The crankshaft of the
engine was made of nickel chrome-steel, and was in two parts connected
together at the crank pin; these two parts, after the master-rod had
been placed in position and the other connecting rods had been attached
to it, were firmly secured. The steel crank case was made in five parts,
the two central ones holding the cylinders in place, and on one side
another of the five castings formed a cam-box, to the outside of which
was secured the extension to which the air-screw was attached. On the
other side of the crank case another casting carried the thrust-box, and
the whole crank case, with its cylinders and gear, was carried on the
fixed crank shaft by means of four ball-bearings, one of which also took
the axial thrust of the air-screw.

For these engines, castor oil is the lubricant usually adopted, and it
is pumped to the crankshaft by means of a gear-driven oil pump; from
this shaft the other parts of the engine are lubricated by means of
centrifugal force, and in actual practice sufficient unburnt oil passes
through the cylinders to lubricate the exhaust valve, which partly
accounts for the high rate of consumption of lubricating oil. A very
simple carburettor of the float less, single-spray type was used, and
the mixture was passed along the hollow crankshaft to the interior of
the crank case, thence through the automatic inlet valves in the tops of
the pistons to the combustion chambers of the cylinders. Ignition was
by means of a high-tension magneto specially geared to give the correct
timing, and the working impulses occurred at equal angular intervals of
102.85 degrees. The ignition was timed so that the firing spark occurred
when the cylinder was 26 degrees before the position in which the piston
was at the outer end of its stroke, and this timing gave a maximum
pressure in the cylinder just after the piston had passed this position.

By 1913, eight different sizes of the Gnome engine were being
constructed, ranging from 45 to 180 brake horse-power; four of these
were single-crank engines one having nine and the other three having
seven cylinders. The remaining four were constructed with two cranks;
three of them had fourteen cylinders apiece, ranged in groups of seven,
acting on the cranks, and the one other had eighteen cylinders ranged in
two groups of nine, acting on its two cranks. Cylinders of the two-crank
engines are so arranged (in the fourteen-cylinder type) that fourteen
equal angular impulses occur during each cycle; these engines are
supported on bearings on both sides of the engine, the air-screw being
placed outside the front support. In the eighteen-cylinder model the
impulses occur at each 40 degrees of angular rotation of the cylinders,
securing an extremely even rotation of the air-screw.

In 1913 the Gnome Monosoupape engine was introduced, a model in which
the inlet valve to the cylinder was omitted, while the piston was of the
ordinary cast-iron type. A single exhaust valve in the cylinder head was
operated in a manner similar to that on the previous Gnome engines, and
the fact of this being the only valve on the cylinder gave the engine
its name. Each cylinder contained ports at the bottom which communicated
with the crank chamber, and were overrun by the piston when this was
approaching the bottom end of its stroke. During the working cycle of
the engine the exhaust valve was opened early to allow the exhaust gases
to escape from the cylinder, so that by the time the piston overran the
ports at the bottom the pressure within the cylinder was approximately
equal to that in the crank case, and practically no flow of gas took
place in either direction through the ports. The exhaust valve remained
open as usual during the succeeding up-stroke of the piston, and
the valve was held open until the piston had returned through about
one-third of its downward stroke, thus permitting fresh air to enter the
cylinder. The exhaust valve then closed, and the downward motion of the
piston, continuing, caused a partial vacuum inside the cylinder; when
the piston overran the ports, the rich mixture from the crank case
immediately entered. The cylinder was then full of the mixture, and the
next upward stroke of the piston compressed the charge; upon ignition
the working cycle was repeated. The speed variation of this engine
was obtained by varying the extent and duration of the opening of the
exhaust valves, and was controlled by the pilot by hand-operated levers
acting on the valve tappet rollers. The weight per horsepower of these
engines was slightly less than that of the two-valve type, while the
lubrication of the gudgeon pin and piston showed an improvement, so that
a lower lubricating oil consumption was obtained. The 100 horse-power
Gnome Monosoupape was built with nine cylinders, each 4.33 inches
bore by 5.9 inches stroke, and it developed its rated power at 1,200
revolutions per minute.

An engine of the rotary type, almost as well known as the Gnome, is the
Clerget, in which both cylinders and crank case are made of steel, the
former having the usual radial fins for cooling. In this type the
inlet and exhaust valves are both located in the cylinder head, and
mechanically operated by push-rods and rockers. Pipes are carried from
the crank case to the inlet valve casings to convey the mixture to the
cylinders, a carburettor of the central needle type being used. The
carburetted mixture is taken into the crank case chamber in a manner
similar to that of the Gnome engine. Pistons of aluminium alloy, with
three cast-iron rings, are fitted, the top ring being of the obturator
type. The large end of one of the nine connecting rods embraces the
crank pin and the pressure is taken on two ball-bearings housed in the
end of the rod. This carries eight pins, to which the other rods are
attached, and the main rod being rigid between the crank pin and piston
pin determines the position of the pistons. Hollow connecting-rods
are used, and the lubricating oil for the piston pins passes from the
crankshaft through the centres of the rods. Inlet and exhaust valves
can be set quite independently of one another--a useful point, since
the correct timing of the opening of these valves is of importance. The
inlet valve opens 4 degrees from top centre and closes after the bottom
dead centre of the piston; the exhaust valve opens 68 degrees before
the bottom centre and closes 4 degrees after the top dead centre of the
piston. The magnetos are set to give the spark in the cylinder at 25
degrees before the end of the compression stroke--two high-tension
magnetos are used: if desired, the second one can be adjusted to give
a later spark for assisting the starting of the engine. The lubricating
oil pump is of the valveless two-plunger type, so geared that it runs
at seven revolutions to 100 revolutions of the engine; by counting
the pulsations the speed of the engine can be quickly calculated by
multiplying the pulsations by 100 and dividing by seven. In the 115
horse-power nine-cylinder Clerget the cylinders are 4.7 bore with a 6.3
inches stroke, and the rated power of the engine is obtained at
1,200 revolutions per minute. The petrol consumption is 0.75 pint per
horse-power per hour.

A third rotary aero engine, equally well known with the foregoing two,
is the Le Rhone, made in four different sizes with power outputs of from
50 to 160 horse-power; the two smaller sizes are single crank engines
with seven and nine cylinders respectively, and the larger sizes are
of double-crank design, being merely the two smaller sizes
doubled--fourteen and eighteen-cylinder engines. The inlet and
exhaust valves are located in the cylinder head, and both valves are
mechanically operated by one push-rod and rocker, radial pipes from
crank case to inlet valve casing taking the mixture to the cylinders.
The exhaust valves are placed on the leading, or air-screw side, of the
engine, in order to get the fullest possible cooling effect. The rated
power of each type of engine is obtained at 1,200 revolutions per
minute, and for all four sizes the cylinder bore is 4.13 inches, with
a 5.5 inches piston stroke. Thin cast-iron liners are shrunk into
the steel cylinders in order to reduce the amount of piston friction.
Although the Le Rhone engines are constructed practically throughout
of steel, the weight is only 2.9 lbs. per horse-power in the
eighteen-cylinder type.

American enterprise in the construction of the rotary type is perhaps
best illustrated in the 'Gyro 'engine; this was first constructed with
inlet valves in the heads of the pistons, after the Gnome pattern, the
exhaust valves being in the heads of the cylinders. The inlet valve in
the crown of each piston was mechanically operated in a very ingenious
manner by the oscillation of the connecting-rod. The Gyro-Duplex engine
superseded this original design, and a small cross-section illustration
of this is appended. It is constructed in seven and nine-cylinder sizes,
with a power range of from 50 to 100 horse-power; with the largest size
the low weight of 2.5 lbs.. per horse-power is reached. The design is
of considerable interest to the internal combustion engineer, for it
embodies a piston valve for controlling auxiliary exhaust ports, which
also acts as the inlet valve to the cylinder. The piston uncovers the
auxiliary ports when it reaches the bottom of its stroke, and at the end
of the power stroke the piston is in such a position that the exhaust
can escape over the top of it. The exhaust valve in the cylinder head is
then opened by means of the push-rod and rocker, and is held open until
the piston has completed its upward stroke and returned through more
than half its subsequent return stroke. When the exhaust valve closes,
the cylinder has a charge of fresh air, drawn in through the exhaust
valve, and the further motion of the piston causes a partial vacuum;
by the time the piston reaches bottom dead centre the piston-valve has
moved up to give communication between the cylinder and the crank case,
therefore the mixture is drawn into the cylinder. Both the piston valve
and exhaust valve are operated by cams formed on the one casting, which
rotates at seven-eighths engine speed for the seven-cylinder type, and
nine-tenths engine speed for the nine-cylinder engines. Each of these
cams has four or five points respectively, to suit the number of
cylinders.

The steel cylinders are machined from solid forgings and provided with
webs for air-cooling as shown. Cast-iron pistons are used, and are
connected to the crankshaft in the same manner as with the Gnome and Le
Rhone engines. Petrol is sprayed into the crank case by a small geared
pump and the mixture is taken from there to the piston valves by radial
pipes. Two separate pumps are used for lubrication, one forcing oil to
the crank-pin bearing and the other spraying the cylinders.

Among other designs of rotary aero engines the E.J.C. is noteworthy,
in that the cylinders and crank case of this engine rotate in opposite
directions, and two air-screws are used, one being attached to the end
of the crankshaft, and the other to the crank case. Another interesting
type is the Burlat rotary, in which both the cylinders and crankshaft
rotate in the same direction, the rotation of the crankshaft being twice
that of the cylinders as regards speed. This engine is arranged to
work on the four-stroke cycle with the crankshaft making four, and the
cylinders two, revolutions per cycle.

It would appear that the rotary type of engine is capable of but little
more improvement--save for such devices as these of the last two engines
mentioned, there is little that Laurent Seguin has not already done in
the Gnome type. The limitation of the rotary lies in its high fuel and
lubricating oil consumption, which renders it unsuited for long-distance
aero work; it was, in the war period, an admirable engine for such
short runs as might be involved in patrol work 'over the lines,' and
for similar purposes, but the watercooled Vee or even vertical, with
its much lower fuel consumption, was and is to be preferred for distance
work. The rotary air-cooled type has its uses, and for them it will
probably remain among the range of current types for some time to come.
Experience of matters aeronautical is sufficient to show, however, that
prophecy in any direction is most unsafe.




V. THE HORIZONTALLY-OPPOSED ENGINE

Among the first internal combustion engines to be taken into use with
aircraft were those of the horizontally-opposed four-stroke cycle type,
and, in every case in which these engines were used, their excellent
balance and extremely even torque rendered them ideal-until the
tremendous increase in power requirements rendered the type too long and
bulky for placing in the fuselage of an aeroplane. As power increased,
there came a tendency toward placing cylinders radially round a central
crankshaft, and, as in the case of the early Anzani, it may be said that
the radial engine grew out of the horizontal opposed piston type. There
were, in 1910--that is, in the early days of small power units,
ten different sizes of the horizontally opposed engine listed for
manufacture, but increase in power requirements practically ruled out
the type for air work.

The Darracq firm were the leading makers of these engines in 1910; their
smallest size was a 24 horsepower engine, with two cylinders each of 5.1
inches bore by 4.7 inches stroke. This engine developed its rated power
at 1,500 revolutions per minute, and worked out at a weight of 5 lbs.
per horse-power. With these engines the cranks are so placed that two
regular impulses are given to the crankshaft for each cycle of working,
an arrangement which permits of very even balancing of the inertia
forces of the engine. The Darracq firm also made a four-cylindered
horizontal opposed piston engine, in which two revolutions were given to
the crankshaft per revolution, at equal angular intervals.

The Dutheil-Chambers was another engine of this type, and had
the distinction of being the second largest constructed. At 1,000
revolutions per minute it developed 97 horse-power; its four cylinders
were each of 4.93 inches bore by 11.8 inches stroke--an abnormally long
stroke in comparison with the bore. The weight--which owing to the build
of the engine and its length of stroke was bound to be rather high,
actually amounted to 8.2 lbs. per horse-power. Water cooling was
adopted, and the engine was, like the Darracq four-cylinder type,
so arranged as to give two impulses per revolution at equal angular
intervals of crankshaft rotation.

One of the first engines of this type to be constructed in England was
the Alvaston, a water-cooled model which was made in 20, 30, and 50
brake horse-power sizes, the largest being a four-cylinder engine. All
three sizes were constructed to run at 1,200 revolutions per minute. In
this make the cylinders were secured to the crank case by means of
four long tie bolts passing through bridge pieces arranged across the
cylinder heads, thus relieving the cylinder walls of all longitudinal
explosion stresses. These bridge pieces were formed from chrome
vanadium steel and milled to an 'H' section, and the bearings for the
valve-tappet were forged solid with them. Special attention was given
to the machining of the interiors of the cylinders and the combustion
heads, with the result that the exceptionally high compression of 95
lbs. per square inch was obtained, giving a very flexible engine. The
cylinder heads were completely water-jacketed, and copper water-jackets
were also fitted round the cylinders. The mechanically operated valves
were actuated by specially shaped cams, and were so arranged that only
two cams were required for the set of eight valves. The inlet valves at
both ends of the engine were connected by a single feed-pipe to which
the carburettor was attached, the induction piping being arranged above
the engine in an easily accessible position. Auxiliary air ports were
provided in the cylinder walls so that the pistons overran them at the
end of their stroke. A single vertical shaft running in ball-bearings
operated the valves and water circulating pump, being driven by spiral
gearing from the crankshaft at half speed. In addition to the excellent
balance obtained with this engine, the makers claimed with justice that
the number of working parts was reduced to an absolute minimum.

In the two-cylinder Darracq, the steel cylinders were machined from
solid, and auxiliary exhaust ports, overrun by the piston at the inner
end of its stroke, were provided in the cylinder walls, consisting of a
circular row of drilled holes--this arrangement was subsequently adopted
on some of the Darracq racing car engines. The water jackets were of
copper, soldered to the cylinder walls; both the inlet and exhaust
valves were located in the cylinder heads, being operated by rockers and
push-rods actuated by cams on the halftime shaft driven from one end
of the crankshaft. Ignition was by means of a high-tension magneto,
and long induction pipes connected the-ends of the cylinders to the
carburettor, the latter being placed underneath the engine. Lubrication
was effected by spraying oil into the crank case by means of a pump, and
a second pump circulated the cooling water.

Another good example of this type of engine was the Eole, which had
eight opposed pistons, each pair of which was actuated by a common
combustion chamber at the centre of the engine, two crankshafts being
placed at the outer ends of the engine. This reversal of the ordinary
arrangement had two advantages; it simplified induction, and further
obviated the need for cylinder heads, since the explosion drove at two
piston heads instead of at one piston head and the top of the cylinder;
against this, however, the engine had to be constructed strongly enough
to withstand the longitudinal stresses due to the explosions, as the
cranks are placed on the outer ends and the cylinders and crank-cases
take the full force of each explosion. Each crankshaft drove a separate
air-screw.

This pattern of engine was taken up by the Dutheil-Chambers firm in
the pioneer days of aircraft, when the firm in question produced seven
different sizes of horizontal engines. The Demoiselle monoplane used
by Santos-Dumont in 1909 was fitted with a two-cylinder,
horizontally-opposed Dutheil-Chambers engine, which developed 25 brake
horse-power at a speed of 1,100 revolutions per minute, the cylinders
being of 5 inches bore by 5.1 inches stroke, and the total weight of the
engine being some 120 lbs. The crankshafts of these engines were usually
fitted with steel flywheels in order to give a very even torque,
the wheels being specially constructed with wire spokes. In all the
Dutheil-Chambers engines water cooling was adopted, and the cylinders
were attached to the crank cases by means of long bolts passing through
the combustion heads.

For their earliest machines, the Clement-Bayard firm constructed
horizontal engines of the opposed piston type. The best known of these
was the 30 horse-power size, which had cylinders of 4.7 inches diameter
by 5.1 inches stroke, and gave its rated power at 1,200 revolutions per
minute. In this engine the steel cylinders were secured to the crank
case by flanges, and radiating ribs were formed around the barrel
to assist the air-cooling. Inlet and exhaust valves were actuated by
push-rods and rockers actuated from the second motion shaft mounted
above the crank case; this shaft also drove the high-tension magneto
with which the engine was fitted. A ring of holes drilled round each
cylinder constituted auxiliary ports which the piston uncovered at the
inner end of its stroke, and these were of considerable assistance not
only in expelling exhaust gases, but also in moderating the temperature
of the cylinder and of the main exhaust valve fitted in the cylinder
head. A water-cooled Clement-Bayard horizontal engine was also made, and
in this the auxiliary exhaust ports were not embodied; except in this
particular, the engine was very similar to the water-cooled Darracq.

The American Ashmusen horizontal engine, developing 100 horse-power, is
probably the largest example of this type constructed. It was made with
six cylinders arranged on each side of a common crank case, with long
bolts passing through the cylinder heads to assist in holding them down.
The induction piping and valve-operating gear were arranged below the
engine, and the half-speed shaft carried the air-screw.

Messrs Palons and Beuse, Germans, constructed a light-weight,
air-cooled, horizontally-opposed engine, two-cylindered. In this the
cast-iron cylinders were made very thin, and were secured to the
crank case by bolts passing through lugs cast on the outer ends of
the cylinders; the crankshaft was made hollow, and holes were drilled
through the webs of the connecting-rods in order to reduce the weight.
The valves were fitted to the cylinder heads, the inlet valves being of
the automatic type, while the exhaust valves were mechanically operated
from the cam-shaft by means of rockers and push-rods. Two carburettors
were fitted, to reduce the induction piping to a minimum; one was
attached to each combustion chamber, and ignition was by the normal
high-tension magneto driven from the halftime shaft.

There was also a Nieuport two-cylinder air-cooled horizontal engine,
developing 35 horse-power when running at 1,300 revolutions per minute,
and being built at a weight of 5.1 lbs. per horse-power. The cylinders
were of 5.3 inches diameter by 5.9 inches stroke; the engine followed
the lines of the Darracq and Dutheil-Chambers pretty closely, and thus
calls for no special description.

The French Kolb-Danvin engine of the horizontal type, first constructed
in 1905, was probably the first two-stroke cycle engine designed to
be applied to the propulsion of aircraft; it never got beyond the
experimental stage, although its trials gave very good results. Stepped
pistons were adopted, and the charging pump at one end was used to
scavenge the power cylinder at the other ends of the engine, the
transfer ports being formed in the main casting. The openings of these
ports were controlled at both ends by the pistons, and the location of
the ports appears to have made it necessary to take the exhaust from the
bottom of one cylinder and from the top of the other. The carburetted
mixture was drawn into the scavenging cylinders, and the usual
deflectors were cast on the piston heads to assist in the scavenging and
to prevent the fresh gas from passing out of the exhaust ports.




VI. THE TWO-STROKE CYCLE ENGINE

Although it has been little used for aircraft propulsion, the
possibilities of the two-stroke cycle engine render some study of
it desirable in this brief review of the various types of internal
combustion engine applicable both to aeroplanes and airships.
Theoretically the two-stroke cycle engine--or as it is more commonly
termed, the 'two-stroke,' is the ideal power producer; the doubling of
impulses per revolution of the crankshaft should render it of very much
more even torque than the four-stroke cycle types, while, theoretically,
there should be a considerable saving of fuel, owing to the doubling of
the number of power strokes per total of piston strokes. In practice,
however, the inefficient scavenging of virtually every two-stroke cycle
engine produced nullifies or more than nullifies its advantages over the
four-stroke cycle engine; in many types, too, there is a waste of fuel
gases through the exhaust ports, and much has yet to be done in the way
of experiment and resulting design before the two-stroke cycle engine
can be regarded as equally reliable, economical, and powerful with its
elder brother.

The first commercially successful engine operating on the two-stroke
cycle was invented by Mr Dugald Clerk, who in 1881 proved the design
feasible. As is more or less generally understood, the exhaust gases of
this engine are discharged from the cylinder during the time that
the piston is passing the inner dead centre, and the compression,
combustion, and expansion of the charge take place in similar manner
to that of the four-stroke cycle engine. The exhaust period is usually
controlled by the piston overrunning ports in the cylinder at the end
of its working stroke, these ports communicating direct with the outer
air--the complication of an exhaust valve is thus obviated; immediately
after the escape of the exhaust gases, charging of the cylinder occurs,
and the fresh gas may be introduced either through a valve in the
cylinder head or through ports situated diametrically opposite to the
exhaust ports. The continuation of the outward stroke of the piston,
after the exhaust ports have been closed, compresses the charge into
the combustion chamber of the cylinder, and the ignition of the mixture
produces a recurrence of the working stroke.

Thus, theoretically, is obtained the maximum of energy with the minimum
of expenditure; in practice, however, the scavenging of the power
cylinder, a matter of great importance in all internal combustion
engines, is often imperfect, owing to the opening of the exhaust ports
being of relatively short duration; clearing the exhaust gases out of
the cylinder is not fully accomplished, and these gases mix with the
fresh charge and detract from its efficiency. Similarly, owing to the
shorter space of time allowed, the charging of the cylinder with the
fresh mixture is not so efficient as in the four-stroke cycle type; the
fresh charge is usually compressed slightly in a separate chamber--crank
case, independent cylinder, or charging pump, and is delivered to
the working cylinder during the beginning of the return stroke of the
piston, while in engines working on the four-stroke cycle principle a
complete stroke is devoted to the expulsion of the waste gases of the
exhaust, and another full stroke to recharging the cylinder with fresh
explosive mixture.

Theoretically the two-stroke and the four-stroke cycle engines possess
exactly the same thermal efficiency, but actually this is modified by a
series of practical conditions which to some extent tend to neutralise
the very strong case in favour of the two-stroke cycle engine. The
specific capacity of the engine operating on the two-stroke principle is
theoretically twice that of one operating on the four-stroke cycle, and
consequently, for equal power, the former should require only about half
the cylinder volume of the latter; and, owing to the greater superficial
area of the smaller cylinder, relatively, the latter should be far more
easily cooled than the larger four-stroke cycle cylinder; thus it should
be possible to get higher compression pressures, which in turn should
result in great economy of working. Also the obtaining of a working
impulse in the cylinder for each revolution of the crankshaft should
give a great advantage in regularity of rotation--which it undoubtedly
does--and the elimination of the operating gear for the valves, inlet
and exhaust, should give greater simplicity of design.

In spite of all these theoretical--and some practical--advantages the
four-stroke cycle engine was universally adopted for aircraft work;
owing to the practical equality of the two principles of operation, so
far as thermal efficiency and friction losses are concerned, there is no
doubt that the simplicity of design (in theory) and high power output
to weight ratio (also in theory) ought to have given the 'two-stroke'
a place on the aeroplane. But this engine has to be developed so as to
overcome its inherent drawbacks; better scavenging methods have yet to
be devised--for this is the principal drawback--before the two-stroke
can come to its own as a prime mover for aircraft.

Mr Dugald Clerk's original two-stroke cycle engine is indicated roughly,
as regards principle, by the accompanying diagram, from which it will
be seen that the elimination of the ordinary inlet and exhaust valves
of the four-stroke type is more than compensated by a separate cylinder
which, having a piston worked from the connecting-rod of the power
cylinder, was used to charging, drawing the mixture from the carburettor
past the valve in the top of the charging cylinder, and then forcing it
through the connecting pipe into the power cylinder. The inlet valves
both on the charging and the power cylinders are automatic; when the
power piston is near the bottom of its stroke the piston in the charging
cylinder is compressing the carburetted air, so that as soon as the
pressure within the power cylinder is relieved by the exit of the burnt
gases through the exhaust ports the pressure in the charging cylinder
causes the valve in the head of the power cylinder to open, and fresh
mixture flows into the cylinder, replacing the exhaust gases. After
the piston has again covered the exhaust ports the mixture begins to be
compressed, thus automatically closing the inlet valve. Ignition
occurs near the end of the compression stroke, and the working stroke
immediately follows, thus giving an impulse to the crankshaft on every
down stroke of the piston. If the scavenging of the cylinder were
complete, and the cylinder were to receive a full charge of fresh
mixture for every stroke, the same mean effective pressure as is
obtained with four-stroke cycle engines ought to be realised, and at
an equal speed of rotation this engine should give twice the power
obtainable from a four-stroke cycle engine of equal dimensions. This
result was not achieved, and, with the improvements in construction
brought about by experiment up to 1912, the output was found to be only
about fifty per cent more than that of a four-stroke cycle engine of the
same size, so that, when the charging cylinder is included, this engine
has a greater weight per horse-power, while the lowest rate of fuel
consumption recorded was 0.68 lb. per horse-power per hour.

In 1891 Mr Day invented a two-stroke cycle engine which used the crank
case as a scavenging chamber, and a very large number of these engines
have been built for industrial purposes. The charge of carburetted air
is drawn through a non-return valve into the crank chamber during the
upstroke of the piston, and compressed to about 4 lbs. pressure per
square inch on the down stroke. When the piston approaches the bottom
end of its stroke the upper edge first overruns an exhaust port, and
almost immediately after uncovers an inlet port on the opposite side of
the cylinder and in communication with the crank chamber; the entering
charge, being under pressure, assists in expelling the exhaust gases
from the cylinder. On the next upstroke the charge is compressed into
the combustion space of the cylinder, a further charge simultaneously
entering the crank case to be compressed after the ignition for the
working stroke. To prevent the incoming charge escaping through the
exhaust ports of the cylinder a deflector is formed on the top of the
piston, causing the fresh gas to travel in an upward direction, thus
avoiding as far as possible escape of the mixture to the atmosphere.
From experiments conducted in 1910 by Professor Watson and Mr Fleming
it was found that the proportion of fresh gases which escaped unburnt
through the exhaust ports diminished with increase of speed; at 600
revolutions per minute about 36 per cent of the fresh charge was lost;
at 1,200 revolutions per minute this was reduced to 20 per cent, and at
1,500 revolutions it was still farther reduced to 6 per cent.

So much for the early designs. With regard to engines of this type
specially constructed for use with aircraft, three designs call for
special mention. Messrs A. Gobe and H. Diard, Parisian engineers,
produced an eight-cylindered two-stroke cycle engine of rotary design,
the cylinders being co-axial. Each pair of opposite pistons was secured
together by a rigid connecting rod, connected to a pin on a rotating
crankshaft which was mounted eccentrically to the axis of rotation
of the cylinders. The crankshaft carried a pinion gearing with an
internally toothed wheel on the transmission shaft which carried the
air-screw. The combustible mixture, emanating from a common supply pipe,
was led through conduits to the front ends of the cylinders, in which
the charges were compressed before being transferred to the working
spaces through ports in tubular extensions carried by the pistons.
These extensions had also exhaust ports, registering with ports in the
cylinder which communicated with the outer air, and the extensions slid
over depending cylinder heads attached to the crank case by long studs.
The pump charge was compressed in one end of each cylinder, and the
pump spaces each delivered into their corresponding adjacent combustion
spaces. The charges entered the pump spaces during the suction period
through passages which communicated with a central stationary supply
passage at one end of the crank case, communication being cut off when
the inlet orifice to the passage passed out of register with the port
in the stationary member. The exhaust ports at the outer end of the
combustion space opened just before and closed a little later than the
air ports, and the incoming charge assisted in expelling the exhaust
gases in a manner similar to that of the earlier types of two-stroke
cycle engine; The accompanying rough diagram assists in showing the
working of this engine.

Exhibited in the Paris Aero Exhibition of 1912, the Laviator two-stroke
cycle engine, six-cylindered, could be operated either as a radial or
as a rotary engine, all its pistons acting on a single crank. Cylinder
dimensions of this engine were 3.94 inches bore by 5.12 inches stroke,
and a power output of 50 horse-power was obtained when working at a rate
of 1,200 revolutions per minute. Used as a radial engine, it developed
65 horse-power at the same rate of revolution, and, as the total weight
was about 198 lbs., the weight of about 3 lbs. per horse-power was
attained in radial use. Stepped pistons were employed, the annular space
between the smaller or power piston and the walls of the larger cylinder
being used as a charging pump for the power cylinder situated 120
degrees in rear of it. The charging cylinders were connected by short
pipes to ports in the crank case which communicated with the hollow
crankshaft through which the fresh gas was supplied, and once in each
revolution each port in the case registered with the port in the
hollow shaft. The mixture which then entered the charging cylinder was
transferred to the corresponding working cylinder when the piston of
that cylinder had reached the end of its power stroke, and immediately
before this the exhaust ports diametrically opposite the inlet ports
were uncovered; scavenging was thus assisted in the usual way. The very
desirable feature of being entirely valveless was accomplished with this
engine, which is also noteworthy for exceedingly compact design.

The Lamplough six-cylinder two-stroke cycle rotary, shown at the Aero
Exhibition at Olympia in 1911, had several innovations, including a
charging pump of rotary blower type. With the six cylinders, six power
impulses at regular intervals were given on each rotation; otherwise,
the cycle of operations was carried out much as in other two-stroke
cycle engines. The pump supplied the mixture under slight pressure to
an inlet port in each cylinder, which was opened at the same time as the
exhaust port, the period of opening being controlled by the piston. The
rotary blower sucked the mixture from the carburettor and delivered it
to a passage communicating with the inlet ports in the cylinder walls.
A mechanically-operated exhaust valve was placed in the centre of each
cylinder head, and towards the end of the working stroke this valve
opened, allowing part of the burnt gases to escape to the atmosphere;
the remainder was pushed out by the fresh mixture going in through the
ports at the bottom end of the cylinder. In practice, one or other of
the cylinders was always taking fresh mixture while working, therefore
the delivery from the pump was continuous and the mixture had not to be
stored under pressure.

The piston of this engine was long enough to keep the ports covered
when it was at the top of the stroke, and a bottom ring was provided
to prevent the mixture from entering the crank case. In addition to
preventing leakage, this ring no doubt prevented an excess of oil
working up the piston into the cylinder. As the cylinder fired with
every revolution, the valve gear was of the simplest construction, a
fixed cam lifting each valve as the cylinder came into position. The
spring of the exhaust valve was not placed round the stem in the usual
way, but at the end of a short lever, away from the heat of the exhaust
gases. The cylinders were of cast steel, the crank case of aluminium,
and ball-bearings were fitted to the crankshaft, crank pins, and the
rotary blower pump. Ignition was by means of a high-tension magneto of
the two-spark pattern, and with a total weight of 300 lbs. the maximum
output was 102 brake horse-power, giving a weight of just under 3 lbs.
per horse-power.

One of the most successful of the two-stroke cycle engines was that
designed by Mr G. F. Mort and constructed by the New Engine Company.
With four cylinders of 3.69 inches bore by 4.5 inches stroke, and
running at 1,250 revolutions per minute, this engine developed 50 brake
horse-power; the total weight of the engine was 155 lbs., thus giving a
weight of 3.1 lbs. per horse-power. A scavenging pump of the rotary type
was employed, driven by means of gearing from the engine crankshaft, and
in order to reduce weight to a minimum the vanes were of aluminium. This
engine was tried on a biplane, and gave very satisfactory results.

American design yields two apparently successful two-stroke cycle aero
engines. A rotary called the Fredericson engine was said to give an
output of 70 brake horse-power with five cylinders 4.5 inches diameter
by 4.75 inches stroke, running at 1,000 revolutions per minute. Another,
the Roberts two-stroke cycle engine, yielded 100 brake horse-power
from six cylinders of the stepped piston design; two carburettors, each
supplying three cylinders, were fitted to this engine. Ignition was
by means of the usual high-tension magneto, gear-driven from the
crankshaft, and the engine, which was water-cooled, was of compact
design.

It may thus be seen that the two-stroke cycle type got as far as actual
experiment in air work, and that with considerable success. So far,
however, the greater reliability of the four-stroke cycle has rendered
it practically the only aircraft engine, and the two-stroke has yet some
way to travel before it becomes a formidable competitor, in spite of its
admitted theoretical and questioned practical advantages.




VII. ENGINES OF THE WAR PERIOD

The principal engines of British, French, and American design used in
the war period and since are briefly described under the four distinct
types of aero engine; such notable examples as the Rolls-Royce,
Sunbeam, and Napier engines have been given special mention, as they
embodied--and still embody--all that is best in aero engine practice. So
far, however, little has been said about the development of German aero
engine design, apart from the early Daimler and other pioneer makes.

At the outbreak of hostilities in 1914, thanks to subsidies to
contractors and prizes to aircraft pilots, the German aeroplane
industry was in a comparatively flourishing condition. There were about
twenty-two establishments making different types of heavier-than-air
machines, monoplane and biplane, engined for the most part with the
four-cylinder Argus or the six-cylinder Mercedes vertical type engines,
each of these being of 100 horse-power--it was not till war brought
increasing demands on aircraft that the limit of power began to rise.
Contemporary with the Argus and Mercedes were the Austro-Daimler,
Benz, and N.A.G., in vertical design, while as far as rotary types were
concerned there were two, the Oberursel and the Stahlhertz; of these the
former was by far the most promising, and it came to virtual monopoly
of the rotary-engined plane as soon as the war demand began. It was
practically a copy of the famous Gnome rotary, and thus deserves little
description.

Germany, from the outbreak of war, practically, concentrated on the
development of the Mercedes engine; and it is noteworthy that, with one
exception, increase of power corresponding with the increased demand
for power was attained without increasing the number of cylinders. The
various models ranged between 75 and 260 horse-power, the latter being
the most recent production of this type. The exception to the rule
was the eight-cylinder 240 horse-power, which was replaced by the 260
horse-power six-cylinder model, the latter being more reliable and but
very slightly heavier. Of the other engines, the 120 horsepower Argus
and the 160 and 225 horse-power Benz were the most used, the Oberursel
being very largely discarded after the Fokker monoplane had had its day,
and the N.A.G. and Austro-Daimler Daimler also falling to comparative
disuse. It may be said that the development of the Mercedes engine
contributed very largely to such success as was achieved in the war
period by German aircraft, and, in developing the engine, the builders
were careful to make alterations in such a way as to effect the least
possible change in the design of aeroplane to which they were to be
fitted. Thus the engine base of the 175 horse-power model coincided
precisely with that of the 150 horse-power model, and the 200 and 240
horse-power models retained the same base dimensions. It was estimated,
in 1918, that well over eighty per cent of German aircraft was engined
with the Mercedes type.

In design and construction, there was nothing abnormal about the
Mercedes engine, the keynote throughout being extreme reliability and
such simplification of design as would permit of mass production in
different factories. Even before the war, the long list of records set
up by this engine formed practical application of the wisdom of this
policy; Bohn's flight of 24 hours 10 minutes, accomplished on July 10th
and 11th, 1914, 9is an instance of this--the flight was accomplished on
an Albatross biplane with a 75 horsepower Mercedes engine. The radial
type, instanced in other countries by the Salmson and Anzani makes, was
not developed in Germany; two radial engines were made in that country
before the war, but the Germans seemed to lose faith in the type under
war conditions, or it may have been that insistence on standardisation
ruled out all but the proved examples of engine.

Details of one of the middle sizes of Mercedes motor, the 176
horse-power type, apply very generally to the whole range; this size was
in use up to and beyond the conclusion of hostilities, and it may still
be regarded as characteristic of modern (1920) German practice. The
engine is of the fixed vertical type, has six cylinders in line, not
off-set, and is water-cooled. The cam shaft is carried in a special
bronze casing, seated on the immediate top of the cylinders, and a
vertical shaft is interposed between crankshaft and camshaft, the latter
being driven by bevel gearing.

On this vertical connecting-shaft the water pump is located, serving to
steady the motion of the shaft. Extending immediately below the camshaft
is another vertical shaft, driven by bevel gears from the crank-shaft,
and terminating in a worm which drives the multiple piston oil pumps.

The cylinders are made from steel forgings, as are the valve chamber
elbows, which are machined all over and welded together. A jacket of
light steel is welded over the valve elbows and attached to a flange
on the cylinders, forming a water-cooling space with a section of about
7/16 of an inch. The cylinder bore is 5.5 inches, and the stroke 6.29
inches. The cylinders are attached to the crank case by means of dogs
and long through bolts, which have shoulders near their lower ends and
are bolted to the lower half of the crank chamber. A very light and
rigid structure is thus obtained, and the method of construction won the
flattery of imitation by makers of other nationality.

The cooling system for the cylinders is extremely efficient. After
leaving the water pump, the water enters the top of the front cylinders
and passes successively through each of the six cylinders of the row;
short tubes, welded to the tops of the cylinders, serve as connecting
links in the system. The Panhard car engines for years were fitted with
a similar cooling system, and the White and Poppe lorry engines were
also similarly fitted; the system gives excellent cooling effect where
it is most needed, round the valve chambers and the cylinder heads.

The pistons are built up from two pieces; a dropped forged steel piston
head, from which depend the piston pin bosses, is combined with a
cast-iron skirt, into which the steel head is screwed. Four rings are
fitted, three at the upper and one at the lower end of the piston skirt,
and two lubricating oil grooves are cut in the skirt, in addition to the
ring grooves. Two small rivets retain the steel head on the piston skirt
after it has been screwed into position, and it is also welded at two
points. The coefficient of friction between the cast-iron and steel is
considerably less than that which would exist between two steel parts,
and there is less tendency for the skirt to score the cylinder walls
than would be the case if all steel were used--so noticeable is this
that many makers, after giving steel pistons a trial, discarded them in
favour of cast-iron; the Gnome is an example of this, being originally
fitted with a steel piston carrying a brass ring, discarded in favour of
a cast-iron piston with a percentage of steel in the metal mixture. In
the Le Rhone engine the difficulty is overcome by a cast-iron liner to
the cylinders.

The piston pin of the Mercedes is of chrome nickel steel, and is
retained in the piston by means of a set screw and cotter pin. The
connecting rods, of I section, are very short and rigid, carrying
floating bronze bushes which fit the piston pins at the small end, and
carrying an oil tube on each for conveying oil from the crank pin to the
piston pin.

The crankshaft is of chrome nickel steel, carried on seven bearings.
Holes are drilled through each of the crank pins and main bearings, for
half the diameter of the shaft, and these are plugged with pressed brass
studs. Small holes, drilled through the crank cheeks, serve to convey
lubricant from the main bearings to the crank pins. The propeller thrust
is taken by a simple ball thrust bearing at the propeller end of the
crankshaft, this thrust bearing being seated in a steel retainer which
is clamped between the two halves of the crank case. At the forward end
of the crankshaft there is mounted a master bevel gear on six splines;
this bevel floats on the splines against a ball thrust bearing, and,
in turn, the thrust is taken by the crank case cover. A stuffing
box prevents the loss of lubricant out of the front end of the crank
chamber, and an oil thrower ring serves a similar purpose at the
propeller end of the crank chamber.

With a motor speed of 1,450 r.p.m., the vertical shaft at the forward
end of the motor turns at 2,175 r.p.m., this being the speed of the two
magnetos and the water pump. The lower vertical shaft bevel gear and the
magneto driving gear are made integral with the vertical driving shaft,
which is carried in plain bearings in an aluminium housing. This housing
is clamped to the upper half of the crank case by means of three studs.
The cam-shaft carries eighteen cams, these being the inlet and exhaust
cams, and a set of half compression cams which are formed with the
exhaust cams and are put into action when required by means of a lever
at the forward end of the cam-shaft. The cam-shaft is hollow, and
serves as a channel for the conveyance of lubricating oil to each of
the camshaft bearings. At the forward end of this shaft there is also
mounted an air pump for maintaining pressure on the fuel supply tank,
and a bevel gear tachometer drive.

Lubrication of the engine is carried out by a full pressure system.
The oil is pumped through a single manifold, with seven branches to the
crankshaft main bearings, and then in turn through the hollow crankshaft
to the connecting-rod big ends and thence through small tubes, already
noted, to the small end bearings. The oil pump has four pistons and two
double valves driven from a single eccentric shaft on which are mounted
four eccentrics. The pump is continuously submerged in oil; in order to
avoid great variations in pressure in the oil lines there is a piston
operated pressure regulator, cut in between the pump and the oil lines.
The two small pistons of the pump take fresh oil from a tank located in
the fuselage of the machine; one of these delivers oil to the cam shaft,
and one delivers to the crankshaft; this fresh oil mixes with the used
oil, returns to the base, and back to the main large oil pump cylinders.
By means of these small pump pistons a constant quantity of oil is kept
in the motor, and the oil is continually being freshened by means of the
new oil coming in. All the oil pipes are very securely fastened to the
lower half of the crank case, and some cooling of the oil is effected
by air passing through channels cast in the crank case on its way to the
carburettor.

A light steel manifold serves to connect the exhaust ports of the
cylinders to the main exhaust pipe, which is inclined about 25 degrees
from vertical and is arranged to give on to the atmosphere just over the
top of the upper wing of the aeroplane.

As regards carburation, an automatic air valve surrounds the throat of
the carburettor, maintaining normal composition of mixture. A small jet
is fitted for starting and running without load. The channels cast in
the crank chamber, already alluded to in connection with oil-cooling,
serve to warm the air before it reaches the carburettor, of which the
body is water-jacketed.

Ignition of the engine is by means of two Bosch ZH6 magnetos, driven at
a speed of 2,175 revolutions per minute when the engine is running at
its normal speed of 1,450 revolutions. The maximum advance of spark is
12 mm., or 32 degrees before the top dead centre, and the firing order
of the cylinders is 1,5,3,6,2,4.

The radiator fitted to this engine, together with the water-jackets,
has a capacity of 25 litres of water, it is rectangular in shape, and is
normally tilted at an angle of 30 degrees from vertical. Its weight is
26 kg., and it offers but slight head resistance in flight.

The radial type of engine, neglected altogether in Germany, was brought
to a very high state of perfection at the end of the War period by
British makers. Two makes, the Cosmos Engineering Company's 'Jupiter'
and 'Lucifer,' and the A.B.C. 'Wasp II' and 'Dragon Fly 1A' require
special mention for their light weight and reliability on trials.

The Cosmos 'Jupiter' was--for it is no longer being made--a 450
horse-power nine-cylinder radial engine, air-cooled, with the cylinders
set in one single row; it was made both geared to reduce the propeller
revolutions relatively to the crankshaft revolutions, and ungeared;
the normal power of the geared type was 450 horse-power, and the total
weight of the engine, including carburettors, magnetos, etc., was only
757 lbs.; the engine speed was 1,850 revolutions per minute, and the
propeller revolutions were reduced by the gearing to 1,200. Fitted to a
'Bristol Badger' aeroplane, the total weight was 2,800 lbs., including
pilot, passenger, two machine-guns, and full military load; at 7,000
feet the registered speed, with corrections for density, was 137 miles
per hour; in climbing, the first 2,000 feet was accomplished in 1 minute
4 seconds; 4,000 feet was reached in 2 minutes 10 seconds; 6,000 feet
was reached in 3 minutes 33 seconds, and 7,000 feet in 4 minutes 15
seconds. It was intended to modify the plane design and fit a new
propeller, in order to attain even better results, but, if trials were
made with these modifications, the results are not obtainable.

The Cosmos 'Lucifer' was a three-cylinder radial type engine of 100
horse-power, inverted Y design, made on the simplest possible principles
with a view to quantity production and extreme reliability. The rated
100 horse-power was attained at 1,600 revolutions per minute, and the
cylinder dimensions were 5.75 bore by 6.25 inches stroke. The cylinders
were of aluminium and steel mixture, with aluminium heads; overhead
valves, operated by push rods on the front side of the cylinders, were
fitted, and a simple reducing gear ran them at half engine speed. The
crank case was a circular aluminium casting, the engine being attached
to the fuselage of the aeroplane by a circular flange situated at the
back of the case; propeller shaft and crankshaft were integral. Dual
ignition was provided, the generator and distributors being driven off
the back end of the engine and the distributors being easily accessible.
Lubrication was by means of two pumps, one scavenging and one suction,
oil being fed under pressure from the crankshaft. A single carburettor
fed all three cylinders, the branch pipe from the carburettor to the
circular ring being provided with an exhaust heater. The total weight of
the engine, 'all on,' was 280 lbs.

The A.B.C. 'Wasp II,' made by Walton Motors, Limited, is a
seven-cylinder radial, air-cooled engine, the cylinders having a bore
of 4.75 inches and stroke 6.25 inches. The normal brake horse-power
at 1,650 revolutions is 160, and the maximum 200 at a speed of 1,850
revolutions per minute. Lubrication is by means of two rotary pumps,
one feeding through the hollow crankshaft to the crank pin, giving
centrifugal feed to big end and thence splash oiling, and one feeding to
the nose of the engine, dropping on to the cams and forming a permanent
sump for the gears on the bottom of the engine nose. Two carburettors
are fitted, and two two-spark magnetos, running at one and
three-quarters engine speed. The total weight of this engine is 350
lbs., or 1.75 lbs. per horse-power. Oil consumption at 1,850 revolutions
is.03 pints per horse-power per hour, and petrol consumption is.56 pints
per horsepower per hour. The engine thus shows as very economical in
consumption, as well as very light in weight.

The A.B.C. 'Dragon Fly 1A 'is a nine-cylinder radial engine having
one overhead inlet and two overhead exhaust valves per cylinder. The
cylinder dimensions are 5.5 inches bore by 6.5 inches stroke, and
the normal rate of speed, 1,650 revolutions per minute, gives 340
horse-power. The oiling is by means of two pumps, the system being
practically identical with that of the 'Wasp II.' Oil consumption
is.021 pints per brake horse-power per hour, and petrol consumption.56
pints--the same as that of the 'Wasp II.' The weight of the complete
engine, including propeller boss, is 600 lbs., or 1,765 lbs. per
horse-power.

These A.B.C. radials have proved highly satisfactory on tests, and their
extreme simplicity of design and reliability commend them as engineering
products and at the same time demonstrate the value, for aero work, of
the air-cooled radial design--when this latter is accompanied by sound
workmanship. These and the Cosmos engines represent the minimum of
weight per horse-power yet attained, together with a practicable degree
of reliability, in radial and probably any aero engine design.




APPENDIX A

GENERAL MENSIER'S REPORT ON THE TRIALS OF CLEMENT ADER'S AVION.

                                  Paris, October 21, 1897.

Report on the trials of M. Clement Ader's aviation apparatus.

M. Ader having notified the Minister of War by letter, July 21, 1897,
that the Apparatus of Aviation which he had agreed to build under the
conditions set forth in the convention of July 24th, 1894, was ready,
and therefore requesting that trials be undertaken before a Committee
appointed for this purpose as per the decision of August 4th, the
Committee was appointed as follows:--

Division General Mensier, Chairman; Division General Delambre, Inspector
General of the Permanent Works of Coast Defence, Member of the Technical
Committee of the Engineering Corps; Colonel Laussedat, Director of the
Conservatoire des Arts et Metiers; Sarrau, Member of the Institute,
Professor of Mechanical Engineering at the Polytechnic School; Leaute,
Member of the Institute, Professor of Mechanical Engineering at the
Polytechnique School.

Colonel Laussedat gave notice at once that his health and work as
Director of the Conservatoire des Arts et Metiers did not permit him
to be a member of the Committee; the Minister therefore accepted his
resignation on September 24th, and decided not to replace him.

Later on, however, on the request of the Chairman of the Committee, the
Minister appointed a new member General Grillon, commanding the Engineer
Corps of the Military Government of Paris.

To carry on the trials which were to take place at the camp of Satory,
the Minister ordered the Governor of the Military Forces of Paris to
requisition from the Engineer Corps, on the request of the Chairman of
the Committee, the men necessary to prepare the grounds at Satory.

After an inspection made on the 16th an aerodrome was chosen. M. Ader's
idea was to have it of circular shape with a width of 40 metres and an
average diameter of 450 metres. The preliminary work, laying out the
grounds, interior and exterior circumference, etc., was finished at the
end of August; the work of smoothing off the grounds began September 1st
with forty-five men and two rollers, and was finished on the day of the
first tests, October 12th.

The first meeting of the Committee was held August 18th in M. Ader's
workshop; the object being to demonstrate the machine to the Committee
and give all the information possible on the tests that were to be held.
After a careful examination and after having heard all the explanations
by the inventor which were deemed useful and necessary, the Committee
decided that the apparatus seemed to be built with a perfect
understanding of the purpose to be fulfilled as far as one could judge
from a study of the apparatus at rest; they therefore authorised M. Ader
to take the machine apart and carry it to the camp at Satory so as to
proceed with the trials.

By letter of August 19th the Chairman made report to the Minister of the
findings of the Committee.

The work on the grounds having taken longer than was anticipated, the
Chairman took advantage of this delay to call the Committee together
for a second meeting, during which M. Ader was to run the two propulsive
screws situated at the forward end of the apparatus.

The meeting was held October 2nd. It gave the Committee an opportunity
to appreciate the motive power in all its details; firebox, boiler,
engine, under perfect control, absolute condensation, automatic fuel
and feed of the liquid to be vaporised, automatic lubrication and
scavenging; everything, in a word, seemed well designed and executed.

The weights in comparison with the power of the engine realised a
considerable advance over anything made to date, since the two engines
weighed together realised 42 kg., the firebox and boiler 60 kg., the
condenser 15 kg., or a total of 117 kg. for approximately 40 horse-power
or a little less than 3 kg. per horse-power.

One of the members summed up the general opinion by saying: 'Whatever
may be the result from an aviation point of view, a result which could
not be foreseen for the moment, it was nevertheless proven that from
a mechanical point of view M. Ader's apparatus was of the greatest
interest and real ingeniosity. He expressed a hope that in any case the
machine would not be lost to science.'

The second experiment in the workshop was made in the presence of the
Chairman, the purpose being to demonstrate that the wings, having a
spread of 17 metres, were sufficiently strong to support the weight of
the apparatus. With this object in view, 14 sliding supports were placed
under each one of these, representing imperfectly the manner in which
the wings would support the machine in the air; by gradually raising the
supports with the slides, the wheels on which the machine rested were
lifted from the ground. It was evident at that time that the members
composing the skeleton of the wings supported the apparatus, and it was
quite evident that when the wings were supported by the air on every
point of their surface, the stress would be better equalised than when
resting on a few supports, and therefore the resistance to breakage
would be considerably greater.

After this last test, the work on the ground being practically finished,
the machine was transported to Satory, assembled and again made ready
for trial.

At first M. Ader was to manoeuvre the machine on the ground at a
moderate speed, then increase this until it was possible to judge
whether there was a tendency for the machine to rise; and it was only
after M. Ader had acquired sufficient practice that a meeting of the
Committee was to be called to be present at the first part of the
trials; namely, volutions of the apparatus on the ground.

The first test took place on Tuesday, October 12th, in the presence
of the Chairman of the Committee. It had rained a good deal during the
night and the clay track would have offered considerable resistance to
the rolling of the machine; furthermore, a moderate wind was blowing
from the south-west, too strong during the early part of the afternoon
to allow of any trials.

Toward sunset, however, the wind having weakened, M. Ader decided to
make his first trial; the machine was taken out of its hangar, the wings
were mounted and steam raised. M. Ader in his seat had, on each side of
him, one man to the right and one to the left, whose duty was to rectify
the direction of the apparatus in the event that the action of the
rear wheel as a rudder would not be sufficient to hold the machine in a
straight course.

At 5.25 p.m. the machine was started, at first slowly and then at an
increased speed; after 250 or 300 metres, the two men who were being
dragged by the apparatus were exhausted and forced to fall flat on
the ground in order to allow the wings to pass over them, and the
trip around the track was completed, a total of 1,400 metres, without
incident, at a fair speed, which could be estimated to be from 300 to
400 metres per minute. Notwithstanding M. Ader's inexperience, this
being the first time that he had run his apparatus, he followed
approximately the chalk line which marked the centre of the track and he
stopped at the exact point from which he started.

The marks of the wheels on the ground, which was rather soft, did not
show up very much, and it was clear that a part of the weight of the
apparatus had been supported by the wings, though the speed was only
about one-third of what the machine could do had M. Ader used all its
motive power; he was running at a pressure of from 3 to 4 atmospheres,
when he could have used 10 to 12.

This first trial, so fortunately accomplished, was of great importance;
it was the first time that a comparatively heavy vehicle (nearly 400
kg., including the weight of the operator, fuel, and water) had been set
in motion by a tractive apparatus, using the air solely as a propelling
medium. The favourable report turned in by the Committee after the
meeting of October 2nd was found justified by the results demonstrated
on the grounds, and the first problem of aviation, namely, the creation
of efficient motive power, could be considered as solved, since the
propulsion of the apparatus in the air would be a great deal easier
than the traction on the ground, provided that the second part of the
problem, the sustaining of the machine in the air, would be realised.

The next day, Wednesday the 13th, no further trials were made on account
of the rain and wind.

On Thursday the 14th the Chairman requested that General Grillon, who
had just been appointed a member of the Committee, accompany him so as
to have a second witness.

The weather was fine, but a fairly strong, gusty wind was blowing from
the south. M. Ader explained to the two members of the Committee the
danger of these gusts, since at two points of the circumference the wind
would strike him sideways. The wind was blowing in the direction A B,
the apparatus starting from C, and running in the direction shown by the
arrow. The first dangerous spot would be at B. The apparatus had been
kept in readiness in the event of the wind dying down. Toward sunset the
wind seemed to die down, as it had done on the evening of the 12th. M.
Ader hesitated, which, unfortunately, further events only justified, but
decided to make a new trial.

At the start, which took place at 5.15 p.m., the apparatus, having
the wind in the rear, seemed to run at a fairly regular speed; it was,
nevertheless, easy to note from the marks of the wheels on the ground
that the rear part of the apparatus had been lifted and that the rear
wheel, being the rudder, had not been in constant contact with the
ground. When the machine came to the neighbourhood of B, the two members
of the Committee saw the machine swerve suddenly out of the track in a
semicircle, lean over to the right and finally stop. They immediately
proceeded to the point where the accident had taken place and
endeavoured to find an explanation for the same. The Chairman finally
decided as follows:

M. Ader was the victim of a gust of wind which he had feared as he
explained before starting out; feeling himself thrown out of his course,
he tried to use the rudder energetically, but at that time the rear
wheel was not in contact with the ground, and therefore did not
perform its function; the canvas rudder, which had as its purpose the
manoeuvring of the machine in the air, did not have sufficient action
on the ground. It would have been possible without any doubt to react
by using the propellers at unequal speed, but M. Ader, being still
inexperienced, had not thought of this. Furthermore, he was thrown
out of his course so quickly that he decided, in order to avoid a more
serious accident, to stop both engines. This sudden stop produced the
half-circle already described and the fall of the machine on its side.

The damage to the machine was serious; consisting at first sight of the
rupture of both propellers, the rear left wheel and the bending of the
left wing tip. It will only be possible to determine after the machine
is taken apart whether the engine, and more particularly the organs of
transmission, have been put out of line.

Whatever the damage may be, though comparatively easy to repair, it will
take a certain amount of time, and taking into consideration the time
of year it is evident that the tests will have to be adjourned for the
present.

As has been said in the above report, the tests, though prematurely
interrupted, have shown results of great importance, and though the
final results are hard to foresee, it would seem advisable to continue
the trials. By waiting for the return of spring there will be plenty of
time to finish the tests and it will not be necessary to rush matters,
which was a partial cause of the accident. The Chairman of the Committee
personally has but one hope, and that is that a decision be reached
accordingly.

     Division General,

            Chairman of the Committee,

                     Mensier.

Boulogne-sur-Seine, October 21st, 1897.


               Annex to the Report of October 21st.

General Grillon, who was present at the trials of the 14th, and who saw
the report relative to what happened during that day, made the following
observations in writing, which are reproduced herewith in quotation
marks. The Chairman of the Committee does not agree with General Grillon
and he answers these observations paragraph by paragraph.

1. 'If the rear wheel (there is only one of these) left but intermittent
tracks on the ground, does that prove that the machine has a tendency to
rise when running at a certain speed?'

Answer.--This does not prove anything in any way, and I was very careful
not to mention this in my report, this point being exactly what was
needed and that was not demonstrated during the two tests made on the
grounds.

'Does not this unequal pressure of the two pair of wheels on the ground
show that the centre of gravity of the apparatus is placed too far
forward and that under the impulse of the propellers the machine has a
tendency to tilt forward, due to the resistance of the air?'

Answer.--The tendency of the apparatus to rise from the rear when it was
running with the wind seemed to be brought about by the effects of the
wind on the huge wings, having a spread of 17 metres, and I believe that
when the machine would have faced the wind the front wheels would have
been lifted.

During the trials of October 12th, when a complete circuit of the track
was accomplished without incidents, as I and Lieut. Binet witnessed,
there was practically no wind. I was therefore unable to verify whether
during this circuit the two front wheels or the rear wheel were in
constant contact with the ground, because when the trial was over it was
dark (it was 5.30) and the next day it was impossible to see anything
because it had rained during the night and during Wednesday morning. But
what would prove that the rear wheel was in contact with the ground at
all times is the fact that M. Ader, though inexperienced, did not swerve
from the circular track, which would prove that he steered pretty well
with his rear wheel--this he could not have done if he had been in the
air.

In the tests of the 12th, the speed was at least as great as on the
14th.

2. 'It would seem to me that if M. Ader thought that his rear wheels
were off the ground he should have used his canvas rudder in order to
regain his proper course; this was the best way of causing the machine
to rotate, since it would have given an angular motion to the front
axle.'

Answer.--I state in my report that the canvas rudder whose object was
the manoeuvre of the apparatus in the air could have no effect on the
apparatus on the ground, and to convince oneself of this point it is
only necessary to consider the small surface of this canvas rudder
compared with the mass to be handled on the ground, a weight of
approximately 400 kg. According to my idea, and as I have stated in my
report, M. Ader should have steered by increasing the speed on one of
his propellers and slowing down the other. He admitted afterward that
this remark was well founded, but that he did not have time to think of
it owing to the suddenness of the accident.

3. 'When the apparatus fell on its side it was under the sole influence
of the wind, since M. Ader had stopped the machine. Have we not a result
here which will always be the same when the machine comes to the ground,
since the engines will always have to be stopped or slowed down when
coming to the ground? Here seems to be a bad defect of the apparatus
under trial.'

Answer.--I believe that the apparatus fell on its side after coming to
a stop, not on account of the wind, but because the semicircle described
was on rough ground and one of the wheels had collapsed.

                                       Mensier.

October 27th, 1897.




APPENDIX B

Specification and Claims of Wright Patent, No. 821393. Filed March 23rd,
1903. Issued May 22nd, 1906. Expires May 22nd, 1923.

To all whom it may concern.

Be it known that we, Orville Wright and Wilbur Wright, citizens of the
United States, residing in the city of Dayton, county of Montgomery,
and State of Ohio, have invented certain new and useful Improvements in
Flying Machines, of which the following is a specification.

Our invention relates to that class of flying-machines in which
the weight is sustained by the reactions resulting when one or more
aeroplanes are moved through the air edgewise at a small angle of
incidence, either by the application of mechanical power or by the
utilisation of the force of gravity.

The objects of our invention are to provide means for maintaining
or restoring the equilibrium or lateral balance of the apparatus, to
provide means for guiding the machine both vertically and horizontally,
and to provide a structure combining lightness, strength, convenience of
construction and certain other advantages which will hereinafter appear.

To these ends our invention consists in certain novel features, which we
will now proceed to describe and will then particularly point out in the
claims. In the accompanying drawings, Figure I 1 is a perspective view
of an apparatus embodying our invention in one form. Fig. 2 is a plan
view of the same, partly in horizontal section and partly broken away.
Fig. 3 is a side elevation, and Figs. 4 and 5 are detail views, of one
form of flexible joint for connecting the upright standards with the
aeroplanes.

In flying machines of the character to which this invention relates the
apparatus is supported in the air by reason of the contact between the
air and the under surface of one or more aeroplanes, the contact surface
being presented at a small angle of incidence to the air. The relative
movements of the air and aeroplane may be derived from the motion of
the air in the form of wind blowing in the direction opposite to that in
which the apparatus is travelling or by a combined downward and forward
movement of the machine, as in starting from an elevated position or
by combination of these two things, and in either case the operation is
that of a soaring-machine, while power applied to the machine to propel
it positively forward will cause the air to support the machine in a
similar manner. In either case owing to the varying conditions to be
met there are numerous disturbing forces which tend to shift the machine
from the position which it should occupy to obtain the desired results.
It is the chief object of our invention to provide means for remedying
this difficulty, and we will now proceed to describe the construction by
means of which these results are accomplished.

In the accompanying drawing we have shown an apparatus embodying our
invention in one form. In this illustrative embodiment the machine is
shown as comprising two parallel superposed aeroplanes, 1 and 2, may be
embodied in a structure having a single aeroplane. Each aeroplane is of
considerably greater width from side to side than from front to rear.
The four corners of the upper aeroplane are indicated by the reference
letters a, b, c, and d, while the corresponding corners of the lower
aeroplane 2 are indicated by the reference letters e, f, g, and h. The
marginal lines ab and ef indicate the front edges of the aeroplanes, the
lateral margins of the upper aeroplane are indicated, respectively,
by the lines ad and bc, the lateral margins of the lower aeroplane are
indicated, respectively, by the lines eh and fg, while the rear margins
of the upper and lower aeroplanes are indicated, respectively, by the
lines cd and gh.

Before proceeding to a description of the fundamental theory of
operation of the structure we will first describe the preferred mode of
constructing the aeroplanes and those portions of the structure which
serve to connect the two aeroplanes.

Each aeroplane is formed by stretching cloth or other suitable fabric
over a frame composed of two parallel transverse spars 3, extending
from side to side of the machine, their ends being connected by bows 4
extending from front to rear of the machine. The front and rear spars
3 of each aeroplane are connected by a series of parallel ribs 5, which
preferably extend somewhat beyond the rear spar, as shown. These spars,
bows, and ribs are preferably constructed of wood having the necessary
strength, combined with lightness and flexibility. Upon this framework
the cloth which forms the supporting surface of the aeroplane is
secured, the frame being enclosed in the cloth. The cloth for each
aeroplane previous to its attachment to its frame is cut on the bias
and made up into a single piece approximately the size and shape of the
aeroplane, having the threads of the fabric arranged diagonally to the
transverse spars and longitudinal ribs, as indicated at 6 in Fig. 2.
Thus the diagonal threads of the cloth form truss systems with the spars
and ribs, the threads constituting the diagonal members. A hem is formed
at the rear edge of the cloth to receive a wire 7, which is connected to
the ends of the rear spar and supported by the rearwardly-extending ends
of the longitudinal ribs 5, thus forming a rearwardly-extending flap
or portion of the aeroplane. This construction of the aeroplane gives
a surface which has very great strength to withstand lateral and
longitudinal strains, at the same time being capable of being bent or
twisted in the manner hereinafter described.

When two aeroplanes are employed, as in the construction illustrated,
they are connected together by upright standards 8. These standards are
substantially rigid, being preferably constructed of wood and of equal
length, equally spaced along the front and rear edges of the aeroplane,
to which they are connected at their top and bottom ends by hinged
joints or universal joints of any suitable description. We have shown
one form of connection which may be used for this purpose in Figs. 4 and
5 of the drawings. In this construction each end of the standard 8
has secured to it an eye 9 which engages with a hook 10, secured to a
bracket plate 11, which latter plate is in turn fastened to the spar 3.
Diagonal braces or stay-wires 12 extend from each end of each standard
to the opposite ends of the adjacent standards, and as a convenient mode
of attaching these parts I have shown a hook 13 made integral with the
hook 10 to receive the end of one of the stay-wires, the other stay-wire
being mounted on the hook 10. The hook 13 is shown as bent down to
retain the stay-wire in connection to it, while the hook 10 is shown
as provided with a pin 14 to hold the staywire 12 and eye 9 in position
thereon. It will be seen that this construction forms a truss system
which gives the whole machine great transverse rigidity and strength,
while at the same time the jointed connections of the parts permit the
aeroplanes to be bent or twisted in the manner which we will now proceed
to describe.

15 indicates a rope or other flexible connection extending lengthwise
of the front of the machine above the lower aeroplane, passing under
pulleys or other suitable guides 16 at the front corners e and f of the
lower aeroplane, and extending thence upward and rearward to the upper
rear corners c and d, of the upper aeroplane, where they are attached,
as indicated at 17. To the central portion of the rope there is
connected a laterally-movable cradle 18, which forms a means for moving
the rope lengthwise in one direction or the other, the cradle being
movable toward either side of the machine. We have devised this cradle
as a convenient means for operating the rope 15, and the machine is
intended to be generally used with the operator lying face downward on
the lower aeroplane, with his head to the front, so that the operator's
body rests on the cradle, and the cradle can be moved laterally by the
movements of the operator's body. It will be understood, however, that
the rope 15 may be manipulated in any suitable manner.

19 indicates a second rope extending transversely of the machine along
the rear edge of the body portion of the lower aeroplane, passing under
suitable pulleys or guides 20 at the rear corners g and h of the lower
aeroplane and extending thence diagonally upward to the front corners a
and b of the upper aeroplane, where its ends are secured in any suitable
manner, as indicated at 21.

Considering the structure so far as we have now described it, and
assuming that the cradle 18 be moved to the right in Figs. 1 and 2,
as indicated by the arrows applied to the cradle in Fig. 1 and by the
dotted lines in Fig. 2, it will be seen that that portion of the rope 15
passing under the guide pulley at the corner e and secured to the corner
d will be under tension, while slack is paid out throughout the other
side or half of the rope 15. The part of the rope 15 under tension
exercises a downward pull upon the rear upper corner d of the structure
and an upward pull upon the front lower corner e, as indicated by the
arrows. This causes the corner d to move downward and the corner e to
move upward. As the corner e moves upward it carries the corner a upward
with it, since the intermediate standard 8 is substantially rigid and
maintains an equal distance between the corners a and e at all times.
Similarly, the standard 8, connecting the corners d and h, causes the
corner h to move downward in unison with the corner d. Since the corner
a thus moves upward and the corner h moves downward, that portion of
the rope 19 connected to the corner a will be pulled upward through the
pulley 20 at the corner h, and the pull thus exerted on the rope 19 will
pull the corner b on the other wise of the machine downward and at the
same time pull the corner g at said other side of the machine upward.
This results in a downward movement of the corner b and an upward
movement of the corner c. Thus it results from a lateral movement of the
cradle 18 to the right in Fig. 1 that the lateral margins ad and eh at
one side of the machine are moved from their normal positions in which
they lie in the normal planes of their respective aeroplanes, into
angular relations with said normal planes, each lateral margin on this
side of the machine being raised above said normal plane at its forward
end and depressed below said normal plane at its rear end, said lateral
margins being thus inclined upward and forward. At the same time a
reverse inclination is imparted to the lateral margins bc end fg at the
other side of the machine, their inclination being downward and forward.
These positions are indicated in dotted lines in Fig. 1 of the drawings.
A movement of the cradle 18 in the opposite direction from its normal
position will reverse the angular inclination of the lateral margins of
the aeroplanes in an obvious manner. By reason of this construction it
will be seen that with the particular mode of construction now under
consideration it is possible to move the forward corner of the lateral
edges of the aeroplane on one side of the machine either above or below
the normal planes of the aeroplanes, a reverse movement of the forward
corners of the lateral margins on the other side of the machine
occurring simultaneously. During this operation each aeroplane is
twisted or distorted around a line extending centrally across the same
from the middle of one lateral margin to the middle of the other lateral
margin, the twist due to the moving of the lateral margins to different
angles extending across each aeroplane from side to side, so that each
aeroplane surface is given a helicoidal warp or twist. We prefer this
construction and mode of operation for the reason that it gives a
gradually increasing angle to the body of each aeroplane from the
centre longitudinal line thereof outward to the margin, thus giving a
continuous surface on each side of the machine, which has a gradually
increasing or decreasing angle of incidence from the centre of the
machine to either side. We wish it to be understood, however, that our
invention is not limited to this particular construction, since any
construction whereby the angular relations of the lateral margins of
the aeroplanes may be varied in opposite directions with respect to
the normal planes of said aeroplanes comes within the scope of our
invention. Furthermore, it should be understood that while the lateral
margins of the aeroplanes move to different angular positions with
respect to or above and below the normal planes of said aeroplanes,
it does not necessarily follow that these movements bring the opposite
lateral edges to different angles respectively above and below a
horizontal plane since the normal planes of the bodies of the aeroplanes
are inclined to the horizontal when the machine is in flight, said
inclination being downward from front to rear, and while the forward
corners on one side of the machine may be depressed below the
normal planes of the bodies of the aeroplanes said depression is not
necessarily sufficient to carry them below the horizontal planes passing
through the rear corners on that side. Moreover, although we prefer to
so construct the apparatus that the movements of the lateral margins
on the opposite sides of the machine are equal in extent and opposite m
direction, yet our invention is not limited to a construction producing
this result, since it may be desirable under certain circumstances
to move the lateral margins on one side of the machine just described
without moving the lateral margins on the other side of the machine to
an equal extent in the opposite direction. Turning now to the purpose of
this provision for moving the lateral margins of the aeroplanes in the
manner described, it should be premised that owing to various conditions
of wind pressure and other causes the body of the machine is apt to
become unbalanced laterally, one side tending to sink and the other side
tending to rise, the machine turning around its central longitudinal
axis. The provision which we have just described enables the operator
to meet this difficulty and preserve the lateral balance of the machine.
Assuming that for some cause that side of the machine which lies to
the left of the observer in Figs. 1 and 2 has shown a tendency to drop
downward, a movement of the cradle 18 to the right of said figures, as
herein before assumed, will move the lateral margins of the aeroplanes
in the manner already described, so that the margins ad and eh will be
inclined downward and rearward, and the lateral margins bc and fg will
be inclined upward and rearward with respect to the normal planes of the
bodies of the aeroplanes. With the parts of the machine in this position
it will be seen that the lateral margins ad and eh present a larger
angle of incidence to the resisting air, while the lateral margins on
the other side of the machine present a smaller angle of incidence.
Owing to this fact, the side of the machine presenting the larger angle
of incidence will tend to lift or move upward, and this upward movement
will restore the lateral balance of the machine. When the other side of
the machine tends to drop, a movement of the cradle 18 in the reverse
direction will restore the machine to its normal lateral equilibrium. Of
course, the same effect will be produced in the same way in the case of
a machine employing only a single aeroplane.

In connection with the body of the machine as thus operated we employ
a vertical rudder or tail 22, so supported as to turn around a vertical
axis. This rudder is supported at the rear ends on supports or arms 23,
pivoted at their forward ends to the rear margins of the upper and lower
aeroplanes, respectively. These supports are preferably V-shaped, as
shown, so that their forward ends are comparatively widely separated,
their pivots being indicated at 24. Said supports are free to swing
upward at their free rear ends, as indicated in dotted lines in Fig.
3, their downward movement being limited in any suitable manner. The
vertical pivots of the rudder 22 are indicated at 25, and one of these
pivots has mounted thereon a sheave or pulley 26, around which passes a
tiller-rope 27, the ends of which are extended out laterally and secured
to the rope 19 on opposite sides of the central point of said rope. By
reason of this construction the lateral shifting of the cradle 18 serves
to turn the rudder to one side or the other of the line of flight. It
will be observed in this connection that the construction is such that
the rudder will always be so turned as to present its resisting
surface on that side of the machine on which the lateral margins of the
aeroplanes present the least angle of resistance. The reason of this
construction is that when the lateral margins of the aeroplanes are
so turned in the manner hereinbefore described as to present different
angles of incidence to the atmosphere, that side presenting the largest
angle of incidence, although being lifted or moved upward in the manner
already described, at the same time meets with an increased resistance
to its forward motion, while at the same time the other side of the
machine, presenting a smaller angle of incidence, meets with less
resistance to its forward motion and tends to move forward more rapidly
than the retarded side. This gives the machine a tendency to turn around
its vertical axis, and this tendency if not properly met will not only
change the direction of the front of the machine, but will ultimately
permit one side thereof to drop into a position vertically below the
other side with the aero planes in vertical position, thus causing the
machine to fall. The movement of the rudder, hereinbefore described,
prevents this action, since it exerts a retarding influence on that side
of the machine which tends to move forward too rapidly and keeps the
machine with its front properly presented to the direction of flight and
with its body properly balanced around its central longitudinal axis.
The pivoting of the supports 23 so as to permit them to swing upward
prevents injury to the rudder and its supports in case the machine
alights at such an angle as to cause the rudder to strike the ground
first, the parts yielding upward, as indicated in dotted lines in Fig.
3, and thus preventing injury or breakage. We wish it to be understood,
however, that we do not limit ourselves to the particular description of
rudder set forth, the essential being that the rudder shall be vertical
and shall be so moved as to present its resisting surface on that side
of the machine which offers the least resistance to the atmosphere, so
as to counteract the tendency of the machine to turn around a vertical
axis when the two sides thereof offer different resistances to the air.

From the central portion of the front of the machine struts 28 extend
horizontally forward from the lower aeroplane, and struts 29 extend
downward and forward from the central portion of the upper aeroplane,
their front ends being united to the struts 28, the forward extremities
of which are turned up, as indicated at 30. These struts 28 and 29 form
truss-skids projecting in front of the whole frame of the machine
and serving to prevent the machine from rolling over forward when it
alights. The struts 29 serve to brace the upper portion of the main
frame and resist its tendency to move forward after the lower aeroplane
has been stopped by its contact with the earth, thereby relieving the
rope 19 from undue strain, for it will be understood that when the
machine comes into contact with the earth, further forward movement of
the lower portion thereof being suddenly arrested, the inertia of the
upper portion would tend to cause it to continue to move forward if
not prevented by the struts 29, and this forward movement of the upper
portion would bring a very violent strain upon the rope 19, since it
is fastened to the upper portion at both of its ends, while its lower
portion is connected by the guides 20 to the lower portion. The struts
28 and 29 also serve to support the front or horizontal rudder, the
construction of which we will now proceed to describe.

The front rudder 31 is a horizontal rudder having a flexible body, the
same consisting of three stiff crosspieces or sticks 32, 33, and 34, and
the flexible ribs 35, connecting said cross-pieces and extending from
front to rear. The frame thus provided is covered by a suitable fabric
stretched over the same to form the body of the rudder. The rudder is
supported from the struts 29 by means of the intermediate cross-piece
32, which is located near the centre of pressure slightly in front of
a line equidistant between the front and rear edges of the rudder,
the cross-piece 32 forming the pivotal axis of the rudder, so as to
constitute a balanced rudder. To the front edge of the rudder there are
connected springs 36 which springs are connected to the upturned ends 30
of the struts 28, the construction being such that said springs tend to
resist any movement either upward or downward of the front edge of the
horizontal rudder. The rear edge of the rudder lies immediately in front
of the operator and may be operated by him in any suitable manner. We
have shown a mechanism for this purpose comprising a roller or shaft 37,
which may be grasped by the operator so as to turn the same in either
direction. Bands 38 extend from the roller 37 forward to and around a
similar roller or shaft 39, both rollers or shafts being supported in
suitable bearings on the struts 28. The forward roller or shaft has
rearwardly-extending arms 40, which are connected by links 41 with the
rear edge of the rudder 31. The normal position of the rudder 31 is
neutral or substantially parallel with the aeroplanes 1 and 2; but its
rear edge may be moved upward or downward, so as to be above or below
the normal plane of said rudder through the mechanism provided for that
purpose. It will be seen that the springs 36 will resist any tendency of
the forward edge of the rudder to move in either direction, so that when
force is applied to the rear edge of said rudder the longitudinal ribs
35 bend, and the rudder thus presents a concave surface to the action of
the wind either above or below its normal plane, said surface presenting
a small angle of incidence at its forward portion and said angle of
incidence rapidly increasing toward the rear. This greatly increases the
efficiency of the rudder as compared with a plane surface of equal area.
By regulating the pressure on the upper and lower sides of the rudder
through changes of angle and curvature in the manner described a
turning movement of the main structure around its transverse axis may be
effected, and the course of the machine may thus be directed upward
or downward at the will of the operator and the longitudinal balance
thereof maintained.

Contrary to the usual custom, we place the horizontal rudder in front of
the aeroplanes at a negative angle and employ no horizontal tail at all.
By this arrangement we obtain a forward surface which is almost entirely
free from pressure under ordinary conditions of flight, but which even
if not moved at all from its original position becomes an efficient
lifting-surface whenever the speed of the machine is accidentally
reduced very much below the normal, and thus largely counteracts that
backward travel of the centre of pressure on the aeroplanes which has
frequently been productive of serious injuries by causing the machine
to turn downward and forward and strike the ground head-on. We are aware
that a forward horizontal rudder of different construction has been used
in combination with a supporting surface and a rear horizontal-rudder;
but this combination was not intended to effect and does not effect the
object which we obtain by the arrangement hereinbefore described.

We have used the term 'aeroplane' in this specification and the appended
claims to indicate the supporting surface or supporting surfaces by
means of which the machine is sustained in the air, and by this term we
wish to be understood as including any suitable supporting surface which
normally is substantially flat, although. Of course, when constructed
of cloth or other flexible fabric, as we prefer to construct them, these
surfaces may receive more or less curvature from the resistance of the
air, as indicated in Fig. 3.

We do not wish to be understood as limiting ourselves strictly to the
precise details of construction hereinbefore described and shown in
the accompanying drawings, as it is obvious that these details may be
modified without departing from the principles of our invention. For
instance, while we prefer the construction illustrated in which each
aeroplane is given a twist along its entire length in order to set its
opposite lateral margins at different angles, we have already pointed
out that our invention is not limited to this form of construction,
since it is only necessary to move the lateral marginal portions, and
where these portions alone are moved only those upright standards which
support the movable portion require flexible connections at their ends.

Having thus fully described our invention, what we claim as new, and
desire to secure by Letters Patent, is:--

1. In a flying machine, a normally flat aeroplane having lateral
marginal portions capable of movement to different positions above or
below the normal plane of the body of the aeroplane, such movement being
about an axis transverse to the line of flight, whereby said lateral
marginal portions may be moved to different angles relatively to the
normal plane of the body of the aeroplane, so as to present to the
atmosphere different angles of incidence, and means for so moving said
lateral marginal portions, substantially as described.

2. In a flying machine, the combination, with two normally parallel
aeroplanes, superposed the one above the other, of upright standards
connecting said planes at their margins, the connections between the
standards and aeroplanes at the lateral portions of the aeroplanes being
by means of flexible joints, each of said aeroplanes having lateral
marginal portions capable of movement to different positions above or
below the normal plane of the body of the aeroplane, such movement being
about an axis transverse to the line of flight, whereby said lateral
marginal portions may be moved to different angles relatively to the
normal plane of the body of the aeroplane, so as to present to the
atmosphere different angles of incidence, the standards maintaining
a fixed distance between the portions of the aeroplanes which they
connect, and means for imparting such movement to the lateral marginal
portions of the aeroplanes, substantially as described.

3. In a flying machine, a normally flat aeroplane having lateral
marginal portions capable of movement to different positions above or
below the normal plane of the body of the aeroplane, such movement being
about an axis transverse to the line of flight, whereby said lateral
marginal portions may be moved to different angles relatively to the
normal plane of the body of the aeroplane, and also to different angles
relatively to each other, so as to present to the atmosphere different
angles of incidence, and means for simultaneously imparting such
movement to said lateral marginal portions, substantially as described.

4. In a flying machine, the combination, with parallel superposed
aeroplanes, each having lateral marginal portions capable of movement to
different positions above or below the normal plane of the body of the
aeroplane, such movement being about an axis transverse to the line of
flight, whereby said lateral marginal portions may be moved to different
angles relatively to the normal plane of the body of the aeroplane, and
to different angles relatively to each other, so as to present to the
atmosphere different angles of incidence, of uprights connecting said
aeroplanes at their edges, the uprights connecting the lateral portions
of the aeroplanes being connected with said aeroplanes by flexible
joints, and means for simultaneously imparting such movement to said
lateral marginal portions, the standards maintaining a fixed distance
between the parts which they connect, whereby the lateral portions on
the same side of the machine are moved to the same angle, substantially
as described.

5. In a flying machine, an aeroplane having substantially the form of a
normally flat rectangle elongated transversely to the line of flight,
in combination which means for imparting to the lateral margins of said
aeroplane a movement about an axis lying in the body of the aeroplane
perpendicular to said lateral margins, and thereby moving said lateral
margins into different angular relations to the normal plane of the body
of the aeroplane, substantially as described.

6. In a flying machine, the combination, with two superposed and
normally parallel aeroplanes, each having substantially the form of a
normally flat rectangle elongated transversely to the line of flight,
of upright standards connecting the edges of said aeroplanes to maintain
their equidistance, those standards at the lateral portions of said
aeroplanes being connected therewith by flexible joints, and means for
simultaneously imparting to both lateral margins of both aeroplanes a
movement about axes which are perpendicular to said margins and in the
planes of the bodies of the respective aeroplanes, and thereby moving
the lateral margins on the opposite sides of the machine into different
angular relations to the normal planes of the respective aeroplanes, the
margins on the same side of the machine moving to the same angle, and
the margins on one side of the machine moving to an angle different from
the angle to which the margins on the other side of the machine move,
substantially as described.

7. In a flying machine, the combination, with an aeroplane, and means
for simultaneously moving the lateral portions thereof into different
angular relations to the normal plane of the body of the aeroplane and
to each other, so as to present to the atmosphere different angles of
incidence, of a vertical rudder, and means whereby said rudder is
caused to present to the wind that side thereof nearest the side of the
aeroplane having the smaller angle of incidence and offering the least
resistance to the atmosphere, substantially as described.

8. In a flying machine, the combination, with two superposed and
normally parallel aeroplanes, upright standards connecting the edges of
said aeroplanes to maintain their equidistance, those standards at
the lateral portions of said aeroplanes being connected therewith
by flexible joints, and means for simultaneously moving both lateral
portions of both aeroplanes into different angular relations to the
normal planes of the bodies of the respective aeroplanes, the lateral
portions on one side of the machine being moved to an angle different
from that to which the lateral portions on the other side of the machine
are moved, so as to present different angles of incidence at the two
sides of the machine, of a vertical rudder, and means whereby said
rudder is caused to present to the wind that side thereof nearest
the side of the aeroplanes having the smaller angle of incidence and
offering the least resistance to the atmosphere, substantially as
described.

9. In a flying machine, an aeroplane normally flat and elongated
transversely to the line of flight, in combination with means for
imparting to said aeroplane a helicoidal warp around an axis transverse
to the line of flight and extending centrally along the body aeroplane
in the direction of the elongation aeroplane, substantially as
described.

10. In a flying machine, two aeroplanes, each normally flat and
elongated transversely to the line of flight, and upright standards
connecting the edges of said aeroplanes to maintain their equidistance,
the connections between said standards and aeroplanes being by means of
flexible joints, in combination with means for simultaneously imparting
to each of said aeroplanes a helicoidal warp around an axis transverse
to the line of flight and extending centrally along the body of the
aeroplane in the direction of the aeroplane, substantially as described.

11. In a flying machine, two aeroplanes, each normally flat and
elongated transversely to the line of flight, and upright standards
connecting the edges of said aeroplanes to maintain their equidistance,
the connections between such standards and aeroplanes being by means of
flexible joints, in combination with means for simultaneously imparting
to each of said aeroplanes a helicoidal warp around an axis transverse
to the line of flight and extending centrally along the body of the
aeroplane in the direction of the elongation of the aeroplane, a
vertical rudder, and means whereby said rudder is caused to present to
the wind that side thereof nearest the side of the aeroplanes having
the smaller angle of incidence and offering the least resistance to the
atmosphere, substantially as described.

12. In a flying machine, the combination, with an aeroplane, of a
normally flat and substantially horizontal flexible rudder, and means
for curving said rudder rearwardly and upwardly or rearwardly and
downwardly with respect to its normal plane, substantially as described.

13. In a flying machine, the combination, with an aeroplane, of a
normally flat and substantially horizontal flexible rudder pivotally
mounted on an axis transverse to the line of flight near its centre,
springs resisting vertical movement of the front edge of said rudder,
and means for moving the rear edge of said rudder, above or below the
normal plane thereof, substantially as described.

14. A flying machine comprising superposed connected aeroplanes means
for moving the opposite lateral portions of said aeroplanes to different
angles to the normal planes thereof, a vertical rudder, means for moving
said vertical rudder toward that side of the machine presenting the
smaller angle of incidence and the least resistance to the atmosphere,
and a horizontal rudder provided with means for presenting its upper
or under surface to the resistance of the atmosphere, substantially as
described.

15. A flying machine comprising superposed connected aeroplanes, means
for moving the opposite lateral portions of said aeroplanes to different
angles to the normal planes thereof, a vertical rudder, means for moving
said vertical rudder toward that side of the machine presenting the
smaller angle of incidence and the least resistance to the atmosphere,
and a horizontal rudder provided with means for presenting its upper or
under surface to the resistance of the atmosphere, said vertical rudder
being located at the rear of the machine and said horizontal rudder at
the front of the machine, substantially as described.

16. In a flying machine, the combination, with two superposed and
connected aeroplanes, of an arm extending rearward from each aeroplane,
said arms being parallel and free to swing upward at their rear ends,
and a vertical rudder pivotally mounted in the rear ends of said arms,
substantially as described.

17. A flying machine comprising two superposed aeroplanes, normally
flat but flexible, upright standards connecting the margins of said
aeroplanes, said standards being connected to said aeroplanes by
universal joints, diagonal stay-wires connecting the opposite ends of
the adjacent standards, a rope extending along the front edge of the
lower aeroplane, passing through guides at the front corners thereof,
and having its ends secured to the rear corners of the upper aeroplane,
and a rope extending along the rear edge of the lower aeroplane, passing
through guides at the rear corners thereof, and having its ends secured
to the front corners of the upper aeroplane, substantially as described.

18. A flying machine comprising two superposed aeroplanes, normally
flat but flexible, upright standards connecting the margins of said
aeroplanes, said standards being connected to said aeroplanes by
universal joints, diagonal stay-wires connecting the opposite ends of
the adjacent standards, a rope extending along the front edge of the
lower aeroplane, passing through guides at the front corners thereof,
and having its ends secured to the rear corners of the upper aeroplane,
and a rope extending along the rear edge of the lower aeroplane, passing
through guides at the rear corners thereof, and having its ends secured
to the front corners of the upper aeroplane, in combination with a
vertical rudder, and a tiller-rope connecting said rudder with the rope
extending along the rear edge of the lower aeroplane, substantially as
described.

                              ORVILLE WRIGHT.

                              WILBUR WRIGHT.

Witnesses:

Chas. E. Taylor.

E. Earle Forrer.




APPENDIX C

Proclamation published by the French Government on balloon ascents,
1783.

       NOTICE TO THE PUBLIC! PARIS, 27TH AUGUST, 1783.

On the Ascent of balloons or globes in the air. The one in question
has been raised in Paris this day, 27th August, 1783, at 5 p.m., in the
Champ de Mars.

A Discovery has been made, which the Government deems it right to make
known, so that alarm be not occasioned to the people.

On calculating the different weights of hot air, hydrogen gas, and
common air, it has been found that a balloon filled with either of the
two former will rise toward heaven till it is in equilibrium with the
surrounding air, which may not happen until it has attained a great
height.

The first experiment was made at Annonay, in Vivarais, MM. Montgolfier,
the inventors; a globe formed of canvas and paper, 105 feet in
circumference, filled with heated air, reached an uncalculated height.
The same experiment has just been renewed in Paris before a great crowd.
A globe of taffetas or light canvas covered by elastic gum and filled
with inflammable air, has risen from the Champ de Mars, and been lost
to view in the clouds, being borne in a north-westerly direction. One
cannot foresee where it will descend.

It is proposed to repeat these experiments on a larger scale. Any
one who shall see in the sky such a globe, which resembles 'la lune
obscurcie,' should be aware that, far from being an alarming phenomenon,
it is only a machine that cannot possibly cause any harm, and which will
some day prove serviceable to the wants of society.

(Signed) DE SAUVIGNY.

LENOIR.





End of Project Gutenberg's A History of Aeronautics, by E. Charles Vivian