Produced by Chuck Greif and the Online Distributed
Proofreading Team at http://www.pgdp.net (This file was
produced from images available at The Internet Archive)









            [Illustration: COLOR CEMENT TILES AND POTTERY]




                            [Illustration:

                                 COLOR
                                CEMENT
                              HANDICRAFT

                             PEDRO·J·LEMOS
                             RETA·A·LEMOS

                            THE DAVIS PRESS
                               WORCESTER
                            MASSACHUSETTS]




                            Copyright, 1922
                       by The Davis Press, Inc.
                           Worcester, Mass.

                            Printed in the
                       United States of America




                             Dedicated to

                           ROBERT B. HARSHE

                            Director of the
                         Chicago Art Institute
                       for his early recognition
                           and encouragement
                            of Color Cement
                              Handicraft




TABLE OF CONTENTS


                                                                    Page

Foreword                                                               9

Chapter 1. Materials and Equipment                                    11

Chapter 2. The Making of Plaster Molds                                21

Chapter 3. Plain and Incised Cement Tiles                             33

Chapter 4. Making Vases and Bowls                                     47

Chapter 5. The Use of Color in Cement Tiles                           57

Chapter 6. Color Cement Relief Tiles                                  67

Chapter 7. The Majolica Tile                                          75

Chapter 8. Sgraffito Color Cement Work                                87

Chapter 9. Modeled and Carved Color Cement                            95

Chapter 10. Color Cement for Bowls and Vases                         103

Chapter 11. Glass Mosaic Tiles                                       111

Chapter 12. Flower Boxes and Other Straight Forms                    119

Chapter 13. Color Cement for the Garden                              129

Chapter 14. The Making of Candlesticks and Book Supports             141

Chapter 15. Color Cement for Interior Decoration                     147

Chapter 16. Surface Finishes                                         159

Chapter 17. Decorations in the Open                                  165

Chapter 18. Tile and Pottery with Color Magnesite Cement Work        173

Chapter 19. Color Cement Projects for the Schoolroom                 179

Chapter 20. Designing for Tiles and Pottery                          191




LIST OF ILLUSTRATIONS


                                                                    Page

Color Cement Tiles and Vases. Frontispiece in color

Tools for Color Cement Handicraft                                     18

The Mixing of Plaster-of-Paris                                        19

Helpful Material for Color Cement Handicraft                          20

The Making of Plaster Molds                                           30

The Making of Molds                                                   31

How to Make Color Cement Tiles                                        44

Cement Tile Textures                                                  45

The Incised Tile                                                      46

Vase Molds                                                            55

The Finishing of Cement Pottery                                       56

Use of Color in Cement Tiles                                          64

Color Tile Methods                                                    65

Plaster and Clay Modeled Cement Tiles                                 73

Color Cement Tiles and Pottery by Art School Students                 74

The Majolica Tile                                                     83

Slip Painted Tiles                                                    84

Slip Painted Tile Methods                                             85

Sgraffito Tile and Sgraffito in Architecture                          93

Modeled and Carved Cement Tile Methods                               102

Color Cement Vases                                                   108

Color Cement Vases                                                   109

Mosaic Tile Method                                                   116

Mosaic Tiles                                                         117

Mosaic Stone Tiles                                                   118

Three Cement Box Methods                                             126

The Making of a Cement Box                                           127

Helps in Cement Garden Pottery                                       137

Application of Cement Tiles to Architectural Use                     138

Color Cement Flagstones used for a Bridge, Garden
Pathway and Entrance                                                 139

Color Cement Used for Chimney Stones and Flagstones                  140

Book Support and Candlestick Molds                                   145

Color Cement Tiles for Interior Decoration                           154

Color Cement Tiles for the Fireplace                                 155

Tile Patterns for Wall or Floor                                      156

The Unit Tile and Application                                        157

Cement Tiles and Woodwork                                            158

A Surface Finish for Cement Handicraft                               164

Decorations Painted with Color Cement                                171

Cement Color Painted Decorations Applied                             172

The Making of Magnesite Cement                                       177

Magnesite Objects Cast from Molds                                    178

Schoolroom Projects in Cement                                        185

A Tile in Cement made in the Grammar Grades                          186

A Tile made in the Intermediate Grades                               187

Color Cement Tiles and Pottery made by the Students of a High School 188

Problems in Cement by Students of an Art School                      189

Helpful Design Principles for Color Cement Work                      198

Outline Patterns for Color Cement Handicraft                         199

Tone Patterns for Color Cement Handicraft                            200

Egyptian, Roman, and Aztec Relief Decorations                        201




FOREWORD


It is evident to the most casual observer that the use of cement
and concrete has developed into a most important building
material--undoubtedly the most important of the age. Industrial and
vocational educators have recognized this importance and thousands of
school children have received instruction in its use and application to
objects of utility. Its use has been the subject of many books, and the
reason for the issuing of this book is to present in printed form the
use of color cement for the decoration or surface enrichment of cement
and concrete objects. We heretofore have thought of cement in terms of
rough surfaces and crude retaining walls, little thinking that beautiful
patterns and textures are possible with proper combinations of color
with cement, presenting possibilities for producing art tiles, pottery,
and decorations of a high art quality.

After a study some years ago of the various forms of producing clay
pottery and its possible relation to school arts and industrial
education, the handicap of necessary firing to give permanency loomed
large against its general adaptation by schools. This resulted in
considerable research and experimenting by the authors with cement and
the use of color in the endeavor to parallel in some measure each of the
methods employed in the making of fired tiles and pottery. Particular
attention was given to simplifying the process of securing permanent
form to many of the plastic forms of schoolroom art, which have been
presented in clay and other perishable mediums. With the projects
presented in the following chapters permanent useful objects can be
secured by students in their school art subjects. Attention was also
given to the enriching or refining by decoration the many objects
heretofore made in cement and concrete by vocational classes. The
problems and methods explained in the following description solve this
need.

Craftsmen or amateur home-workers who delight in creating and building
objects of beauty around them can find in color cement a medium which
will appeal to their needs, in that the necessary working equipment is
simple and the work can be done within small space.

The following chapters by no means complete the story of color cement.
They record the results of the work of the authors and it is hoped that
it will stimulate interested readers to carry this delightful handicraft
to even greater achievements.

The results achieved have been accomplished through several years’
patient experimenting by the authors, but the realization that many
other teachers, craftsmen and students will be aided in continuing this
delightful, durable handicraft, is in itself an enjoyable reward to the
authors for their efforts.

Reta A. Lemos

Pedro J. Lemos




[Illustration]

CHAPTER 1

Materials and Equipment

[Illustration]


IN THE MAKING OF COLOR CEMENT HANDICRAFT the chief material used is
Portland cement. While this material has assumed a most important part
in the building history of our present time, there are not many who know
its history and source, and as every craftsman is a better craftsman if
he knows something of the story of the material with which he works,
here is the brief story of Portland cement.

PORTLAND CEMENT DERIVES ITS NAME because of resemblance in color to a
stone quarried near Portland, England, and it was named by its inventor,
Joseph Aspdin in 1824. It is a manufactured product produced by a
scientific process. At the beginning of the Christian era the Romans
used a natural cement very extensively, and many fragments of color
frescoes and friezes remain from the work of the ancients, showing that
they used color with their work.

THE PRINCIPAL INGREDIENTS OF PORTLAND CEMENT are lime, silica, iron, and
alumina. These materials are mixed in definite proportions and then
subjected to a degree of heat that almost causes them to melt, forming a
clinker or slag. This clinker is ground until it is reduced to a powder,
and this is the Portland cement. Portland cement is generally mixed with
an aggregate to produce strength and this aggregate is usually stone,
gravel or sand. The third material needed to complete the combination is
water.

SUCCESS IN THE USE OF CEMENT depends largely upon cement that is fresh.
Cement is very sensitive to moisture and if kept where fogs, dew or
moisture of any nature is absorbed into it, the first set or “hydration”
takes place and destroys its use for fine handicraft.

TO TEST FRESH CEMENT when the cement sack is open, thrust the hand into
it and see that no hard lumps are in it. Fresh cement will feel
slippery and soapy when rubbed between the finger tips. If it feels
gritty and sandy it may do for the rough parts or body of vases and
tiles, but only fresh cement should be used to mix with color and for
surfacing purposes.

THE PROPER CARE OF CEMENT requires that it be kept in a covered
receptacle and kept in a dry place, preferably up from the floor if the
floor is near the ground. It should be kept in a dry, tight work-shop
and the doors should be kept closed at night to avoid any moisture from
the night air reaching it. Nothing can restore spoiled cement and it
should not be used as the results will be discouraging.

GOOD GRADES OF AGGREGATES SHOULD BE USED in cement work. Clean sand
should be used and a sand that is not too fine is preferable. Gravel and
crushed rock used in large work such as garden seats, large bowls and
outdoor problems should be of a good grade to form a good mixture.

THE WATER USED IN CEMENT WORK should be free from all impurities.
Moderately warmed water will hasten the setting or hardening of cement
while very cold water retards the hardening.

THERE ARE TWO COLORS OF CEMENT, gray and white. Portland cement is gray
in color and a white cement is also made that is a refined form of
cement. White cement is not as hard or durable as gray cement, but gives
a smooth surface and sets as satisfactorily as the gray cement. It is
more expensive than the gray cement and should not be used later than
six months after the sack is opened.

WHEN CEMENT IS USED ALONE IT IS TERMED “NEAT.” When it is mixed with
rock, gravel or sand it is termed “concrete.” Concrete produces strength
and the neat cement produces a smooth texture and surface. When concrete
is used the cement and water will rise to the top and if the surface is
worked and pressed with a trowel the cement is “flowed” to the top,
producing a smooth surface.

MOLDS ARE USED FOR FORMING CEMENT AND CONCRETE, and are made from wood,
metal or plaster-of-Paris. The forms in all instances should be tied or
braced together to prevent the moisture of the mixture from running out,
as the water is essential to the successful hardening of the cement. In
the making of cement pottery and tiles, plaster-of-Paris molds or forms
are generally used and plaster-of-Paris therefore forms an important
material in the making of color cement handicraft.

Plaster-of-Paris is made in different degrees of setting periods. These
are quick-setting, medium-setting, and slow-setting. Casting plaster or
sculptor’s plaster should be asked for and a medium-or slow-setting
plaster is preferable for the beginner.

CEMENT, AGGREGATES, WATER AND PLASTER FORM THE MAIN PARTS of our working
materials excepting the color, which is especially described in the
chapter on Color.

THE EQUIPMENT for concrete pottery is simple, and much of it may be
pressed into service from material to be found about the house or
workshop. Inventive ingenuity on the part of the worker will find clever
uses for many discarded kitchen utensils and unused tools.

Following is a list of convenient things needed to produce pottery.
These may be added to or elaborated through personal requirements.

WORKING EQUIPMENT.

    galvanized iron pans about 2 x 3 feet
    2 large spoons
    4 or 5 pans
    2 ladles
    1 large file or rasp
    2 table knives
    3 pieces of ordinary glass about 12 x 18 inches
    1 palette knife
    1 lb. modeling wax
    1 bristle brush ½ inch wide
    2 small sable oil brushes, No. 1 or 2
    1 small clay-modeling tool
    2 pieces of thin wood for mixing paddles
    ½ doz. small saucers or butter dishes
    strips of thin metal
    thin soft wire
    1 sifter
    2 pails
    muller and pestle
    several pieces of surfaced wood about 12 inches square.

With a flat table to work on, running water or a pail of water handy, a
box to receive waste plaster-of-Paris and cement, the proper environment
for color cement is set.

GALVANIZED IRON WATER TRAYS can be made by taking a three-inch by
seven-inch sheet and cutting a two-inch strip off of one end, reserve
for making scrapers and other useful tools. Cut the remaining metal into
three rectangular sections for trays.

To make the trays, lay one of these pieces over a strong box with an
even edge and hammer into tray shape as shown in the accompanying plate.
The corners should be bent so as to make the trays waterproof without
soldering. A wooden mallet should be used for hammering the metal as a
metal hammer may cut the metal.

MOLDING CASE. Several pieces of board hinged together with one series of
edges coming so that they will rest evenly on a flat surface, will
produce an adjustable case to use in making molds. A strong cord will
keep it in place. A strip of metal (tin, brass or iron) may be used as
a cylinder, the circumference being pressed in and tied to conform to
the dimensions of the object to be molded.

MIXING PADDLES. Paddles for mixing plaster or cement can be made out of
firm wood strips and handles shaped to fit the hand.

INCISING TOOLS. A nail hammered into a piece of firm wood and the head
snipped off with nippers then sharpened with a file or emery stone until
it is a tapering wedge point. Nut picks may be filed down slightly for
this purpose. Two or three points of varying widths will be handy to
have, particularly when some of them disappear occasionally as all small
tools will.

SCRAPER. A piece of barrel stave or heavy wire bent like a croquet
wicket with a wire fastened from end to end is particularly convenient
where a number of clay or plasticene tiles are to be produced. For class
use two strips of wood are fastened to the bench, the desired width
separating the strips. Between these strips a piece of strong paper
should be laid and the clay or plasticene pressed firmly onto it between
the strips. The scraper will shave the surplus clay if it is moved along
so that the wire rests on the wooden strips. Measure off the six-inch or
eight-inch squares, cut across with a knife from strip to strip and
remove the squares by sliding the paper out. This will give a smooth,
even surface on which to model or incise designs.

THE OTHER ITEMS OF EQUIPMENT all have their part to play as follows:

    2 large spoons--For handling plaster and cement.
    1 large file or rasp--For occasional use on the tile edge.
    3 pieces of glass--On which to cast tiles.
    2 table knives--For paring molds, etc.
    1 palette knife--For working color into cement.
    1 bristle brush--With which to oil molds.
    Small modeling tool--To use on clay and plasticene.
    Nut picks--For incising.
    ½ doz. small saucers--In which to mix colors.
    Thin soft wire--For cutting molds.
    Sifter--To sift cement and color for glazes.
    2 pails--In which to mix cement and plaster.
    Muller and pestle--Grinding mineral colors with cement.

It may be unnecessary to add that the old axiom “A place for everything
and everything in its place,” will do wonders toward keeping the temper
sweet, and a good temper is a most necessary ingredient for producing
good cement handicraft.

[Illustration: Tools for Color Cement Handicraft]

[Illustration: The Mixing of Plaster-of-Paris]

[Illustration: Helpful Material for Color Cement Handicraft]




[Illustration]

CHAPTER 2

The Making of

Plaster Molds

[Illustration]


THE SUCCESSFUL USE OF PLASTER is such an important part in the making of
color cement tiles and pottery that as a preliminary step or auxiliary
to the cement craft it should be well accomplished by the student before
using the cement. It is not at all difficult and for those who have not
used plaster, there awaits an interesting medium for all forms of
plastic applications or adaptations. Our concern with it will be in the
making of successful molds for the producing or reproducing of our
cement tiles and pottery, but a whole book could be written upon the
making of plaster objects. The uses of plaster form a large industry and
many art objects are produced in plaster for many forms of applied art.

PLASTER IS SENSITIVE to moisture, and should be kept in a dry place. If
plaster does not set within a short time it probably is old and even if
it does set in time it will have a tendency to pulverize. It is always
safer to purchase an entire sack than to purchase a small lot from the
hardware dealer, grocer, or druggist, for the chances are that his
plaster has been exposed in a bin so long that its strength has
vanished. This is mentioned because instances have been known where
trouble in cast making was traced to just such conditions.

ON RECEIVING THE SACKS OF PLASTER AND CEMENT the tendency will be to let
contents remain in the sacks. It will be found much more convenient and
economical to empty the sacks into a small barrel or box to which a
cover has been made. A tin tray under the box or barrel will catch all
waste that may drop around the edge, preventing the material from being
tracked over the floor. A nail or hook on the side of the barrel for
holding the ladle or spoon used for taking out the plaster will enable
you to find it when you need it.

THERE ARE VARIOUS GRADES OF PLASTER, but the best for this purpose is
molding plaster. The plaster should always be kept in a good dry
location.

TO MIX PLASTER SUCCESSFULLY for molds observe the following directions:
A bucket or pan large enough to contain the required amount of plaster
needed should be used. Then half the water for the amount of plaster
used should be poured into the bucket. Sift the plaster-of-Paris through
the fingers into the water, until the water absorbs it no longer. This
can be determined by small portions of the plaster remaining on the
surface. Then stir the whole mass slowly with the mixing paddle until
the passage of the paddle through the plaster leaves a channel which
closes up slowly.

IT IS THEN POURED PROMPTLY into the center of the space on the glass
prepared for the plaster tile so that the poured plaster gradually
spreads from the center toward the corners and edges filling up the
spaces and coming up the sides to about one-half inch height. Jarring
the table or a slight shaking of the glass will cause the plaster to
settle very level as well as causing any bubbles in the plaster to rise
to the surface and break. Care should be taken that the plaster is not
too thick before being poured. This stage of the proceedings requires
one having their wits alert, and discussing Futurist art or any other
topic may result in “try, try again.” If the plaster appears too thin
more plaster should be added until it is the proper consistency.

After the plaster is poured it should set for about half an hour
(varying according to the dryness of the atmosphere) before any attempt
is made to remove it. Meanwhile all buckets, paddles, ladles, etc.,
containing plaster should be cleaned while the plaster is soft and easy
to remove.

WHEN THE PLASTER MOLD IS READY TO REMOVE, a table knife slightly
inserted between partitions and carefully pryed will cause the parts to
separate. A most important part of casting molds and the using of the
plaster molds is the oiling. All parts of the molds to come in contact
with fresh plaster, cement or concrete must be thoroughly oiled or
greased to prevent them sticking to each other. If wood, glass or metal
is used with plaster, cement or concrete, remember to oil or grease such
surface before pouring the plaster or cement on it. If you do not, you
will have to use a chisel and with discouraging results.

The best way to oil the surface is as follows:

GLASS--Apply salad oil with brush or cloth removing as much as will come
with the palm of the hand.

PLASTER BARS AND MOLD should first be soaked in water ten or fifteen
minutes to prevent drawing the moisture out of the fresh plaster or
cement. Wipe off surface moisture with soft cloth, and replace with oil,
before using for molding. If oil is left thick or in brush streaks, it
will leave its influence on the surface of the casting.

WOOD--A smooth-surfaced wood should always be used, and oiled well.

A good grease formula for all surfaces is as follows: Three parts
paraffin and one part tallow, melt and add one pint of kerosene. This is
applied with a brush.

AS AN EXPERIMENT PROBLEM for the use of plaster so as to become familiar
with its use, we will proceed with the casting of a simple flat plaster
tile.

Taking a piece of glass, smooth board, marble or oil cloth, brush the
surface with a little salad or lubricating oil, or linseed oil. There
should be no free oil on the surface or streaks of oil as such will
cause an uneven surface. When using glass it is possible to insert a
diagram or pattern of the shape underneath on a piece of paper as a
guide to the bars or retaining walls of the mold. These retaining bars
or walls may be of various materials. Strips of wood or plaster are
excellent and strips of linoleum, metal and even glass are used. If four
pieces of wood about ten or twelve inches long and one and one-half
inches wide are used they can always be adjusted to fit any dimension
from twelve inches down, by being placed as shown in the diagram.

TO OIL THE RETAINING BARS, brush the surface to come in contact with the
plaster and then hold the wood in position over the diagram below, using
modeling wax or clay to keep it in position. The clay of course should
always be in position on the outside of the wood and should never be in
the space into which the plaster is to be poured.

PLASTER HARDENS SLOWLY IN COLD WEATHER and hardens rapidly in a warm
temperature. Salt added to plaster will cause it to set more rapidly and
to harden more firmly. No exact proportion can be given--just a little
sprinkled in a pan of plaster will cause it to set more rapidly.

DIFFERENT PLASTERS SET AT DIFFERENT PERIODS. As has been described
before, casting plasters can be secured in quick-setting, medium-or
slow-setting mixtures. Medium-setting or slow-setting will be found to
be good average mixtures for use.

TO RELEASE THE PLASTER TILE after it has hardened (generally a half hour
will insure the hardening action as being completed), the bars can be
released and the tile gently lifted at one corner will cause it to come
apart from the oiled surface. If glass is used the glass can be placed
upright and the separating of the tile from the glass can be watched as
indicated by the moisture suction disappearing as the tile is gradually
separated. If oilcloth is used the tile can be turned over and the
oilcloth peeled off easily. This of course is necessary only where any
sticking occurs, for most times the tile will separate easily. If
sticking does occur it is generally some fault of the oiling for it
needs only one or two little spots overlooked to cause considerable
trouble as the plaster will stick to any part that has been skipped in
the oiling.

Plaster dries rapidly and will dry in the sun more rapidly. When plaster
is damp it can be scraped or carved easily. Temperature and the age of
the plaster affect its drying periods.

LARGE TILE MOLDS should be strengthened by having burlap strips or wire
imbedded into the back while the plaster is soft. This creates a
stronger layer than where plaster alone is used. Wood strips should not
be used for backing plaster unless thoroughly dried as otherwise it
causes cracking by its shrinkage, and it is best not to use it for
reinforcing.

TO CORRECT FAULTS IN PLASTER CASTS use a little of the plaster scraped
from the back to fill in holes or defects. If a corner or portion is
broken off, gouge a hole or cavity so that a little plaster mixed and
placed on that section will become firmly connected. As it hardens, a
little of it can then be scraped with a knife to connect correctly with
the surrounding parts or surface.

A SECOND PRACTICE PROBLEM is to take the plaster tile and incise a line
pattern in the surface. To make the incising easier, dip the tile in
water and then trace the design previously prepared onto the plaster.
Pressure alone on the paper with a pencil will make an indentation on
the plaster that can be easily followed in the incising.

THE DESIGNS FOR INCISED PATTERNS are best where the lines enclose a
shape. The parts are more comprehensive and confusion of the lines will
not result if simple outlines are used. In the chapter on Design, line
patterns are shown that are adaptable to incised work.

TO INCISE THE PATTERN take a nail point or nut pick or other metal point
and shape the point on a grindstone or by the use of a file so that each
incised line will have a tapering side. If any undercuts are produced
the cast or plaster that is poured into it will become locked and refuse
to separate.

The tile is next immersed in water, taken out and after the water is
absorbed, a brushing of oil is given to it.

A PLASTER TILE IS MADE MORE DURABLE if it is dried and given a coat or
two of shellac before it is used for molding plaster or cement.
Otherwise repeated brushing of damp plaster with the oil brush will
gradually wear the edges and details of the mold away.

TO MAKE A CAST FROM THE PLASTER MOLD, it is surrounded with the
retaining bars after they have been oiled and held in position with the
modeling wax or clay; this time they are placed firmly against the sides
of the plaster mold.

THE CAST OF OUR FIRST EXPERIMENT now becomes the mold for our second
practice problem as the mold is always the part that produces the cast.
The cast in turn may become a mold for another cast.

TO SEPARATE THE CAST FROM THE MOLD the bars are removed and a knife edge
is pressed between the parts to separate them. Care should be taken not
to become too anxious and force the sections apart before the cast has
dried or they will cause it to break. If it refuses to come apart easily
when completely dry, a little wooden wedge tapped into the crevices in
one or two places will cause it to part easily. Sometimes plaster flows
over the sides of the mold and binds the edges together. On removing the
mold and cast from the retaining bars, examine it to see if any plaster
is binding it and if so remove it.

IF THE PARTS ARE ABSOLUTELY SOLID it is because the incising was not
properly done and the lines interlock somewhere and the only thing to do
is to break them apart and correct the faults and try again. Sometimes
when interlocking tiles are separated the faulty parts have fragments of
the opposite part attached in the defective parts showing where the
faults are located.

THE TWO PLASTER TILES SHOULD BE RETAINED for they can be used in casting
plain cement and color cement tiles in various finishes. When they have
completely dried they should be given two or three coats of thin
shellac, a day apart, on the surface only, which will make them good
durable molds for future use.

CASTING IN THE ROUND is more difficult than flat casting or bas-relief
work and while the making of plaster molds for vases and bowls is given
particular attention in the chapter on Cement Bowls and Vases,
directions for casting objects in the round will be given here.

AS A GOOD TEST PROBLEM take any small object or toy and, if it is wood,
oil it well. If it is porcelain or glass it will not need to be oiled. A
simple form, animal or bird, can be made in modeling wax or clay to be
used as the original or model from which to make a mold. The best
objects are those modeled in broad surfaces with but little detail.

PREPARING FOR CASTING. The equator or half-way mark should be marked on
the surface of the object, as one-half of the mold should be made at a
time. Instead of one-half, one-third is often used on round objects to
permit easier release of the molds. Mold divisions when possible should
follow corners of objects.

THE FIRST SECTION of the mold is made by placing a layer of clay along
the division lines on the object which have been indicated as division
lines for the sections of molds. Sometimes the object can be laid on the
table or on glass and the plaster poured around it up to the half-way
line as shown in the accompanying plate. In this method a strip of
linoleum or metal can be placed around it to make a retaining wall for
the plaster.

AFTER THE FIRST SECTION is cast, the model is removed from the plaster
and if the plaster has risen past the equator it should be scraped back
and indentations or “keys” made in the plaster portions that are not
those producing the parts of the model. The model is replaced in its
hollow and the entire surface of the mold that is exposed is oiled,
including the sides of the metal, linoleum or whatever is used as
retaining walls. Plaster is again poured for the second half after which
it is permitted to dry before separating the mold sections.

OILING. It must be remembered that the molds must be oiled after each
casting as each pouring absorbs the oil. All surfaces coming in contact
with the next pouring of plaster must be oiled to cause separation.

POURING. A hole must be cut in the molds to permit the plaster to enter.
Air holes leading upward as shown in the engraving are scraped upward
out of the molds to permit the escape of the air; otherwise air bubbles
may be formed in the plaster causing defects.

TO HOLD MOLD PARTS TOGETHER tie a cord or wire around parts. Notches cut
on corners or edges of molds to hold the tieing cord will prevent them
from slipping. Molds should fit closely together. If for any reason they
do not, the crevices can be filled with modeling wax as a temporary
filler. The best results are obtained, however, from perfect molds and
it is a saving of time to make a mold over if it is not perfect in the
first casting.

RELEASING CAST. After the plaster has set long enough to harden, the
molds are opened by gentle prying or tapping with a wooden wedge. Often
an obstinate cast is released by placing the mold over a stove or flame
for a few seconds. This causes the steam formed in the mold to separate
the mold from the cast.

CEMENT BOWLS AND VASES are made by pouring thin cement into the molds
and rotating the mold and pouring out the surplus cement. After a few
minutes another layer is poured in and the operation repeated. This
method is explained more fully in the chapter on Bowls and Vases.

[Illustration: The Making of Plaster Molds]

[Illustration: The Making of Molds]




[Illustration]

CHAPTER 3

Plain and Incised

Cement Tiles

[Illustration]


A KNOWLEDGE IN MIXING CEMENT is the next step necessary in Color Cement
Handicraft. The steps necessary toward mixing cement are simple, the
main point being that the cement should be fresh. The student is
cautioned to test the freshness of cement by seeing that no caked or
hard lumps of cement are contained in the sack mixture. As formerly
explained the cement should have a smooth, slippery feeling when passed
between the fingers.

NEAT CEMENT is the term applied to cement mixed with water without the
addition of any sand or gravel. Neat cement produces a very smooth
surface and responds to reproducing every change in the surface of the
model. It should be used on the surface only and not for the entire tile
or pottery. If used without any sand or gravel, it is termed “too fat,”
and has the fault of cracking sooner or later. Therefore neat cement is
always backed up with a concrete mixture.

CONCRETE is a mixture of sand and cement, gravel and cement, or rock and
cement. In all instances where such a mixture is made, the two parts
should be _mixed dry_ before any water is added. Only enough should be
mixed to meet immediate needs as it is not best to use cement that has
stood so long that it has commenced to harden.

TO SECURE A VERY FINE SMOOTH SURFACE for tiles or pottery the cement
should be used neat. It must be sifted dry through a fine sieve and
enough water added to make it of easy working consistency. Then a
mixture of two-thirds gravel or sand and one-third cement with water
added may be used on the back of the tile or the inside of a vase and
possibly again lined with a mixture of neat cement.

Cement or concrete can stand for an hour or two and again be used by
adding more water and mixing thoroughly. This cannot be done with
plaster and should be avoided with cement or concrete. If chemical
action has commenced and the cement has partly set, it naturally will
have lost much of its strength for second use.

A CONCRETE MIXTURE of one part cement and two parts sand or gravel will
give good strength. The sand or gravel must be clean. If it contains any
vegetable matter or other sediment, it should be avoided. To test your
sand quality put a four-inch layer in an ordinary quart jar, fill with
water within three inches of the top. Cover and shake well. Then permit
the sand to settle. If the sediment or loam which remains at the top of
the sand is one-half inch or more, the sand is not fit for use in
concrete.

CEMENT MIXTURES ADAPTABLE TO VARIOUS USES are given below. These may be
used for backing and reinforcing large problems, in garden pottery,
garden furniture or walls.

    1. RICH MIXTURE
       1 part cement
       2 parts sand
       5 parts gravel

    2. STANDARD MIXTURE
       1 part cement
       2 parts sand
       4 parts gravel

    3. MEDIUM MIXTURE
       1 part cement
       2½ parts sand
       3 parts gravel

    4. LEAN MIXTURE
       1 part cement
       3 parts sand
       6 parts gravel


Cement and sand mixed dry first, then with water. The gravel is mixed
wet with other mixture and thoroughly combined.

Builders use the Rich Mixture for columns and high stresses, and where
water tightness is necessary.

Standard Mixture is used for arches, for tanks and sewers, and for
machine foundations.

The Medium Mixture is used for piers, sidewalks, and heavy walls.

The Lean Mixture is used for walls, foundations and for unimportant
work.

THE FIRST PROBLEMS IN CEMENT should be the casting of cement tiles
without the use of color. As a beginning problem set the retaining bars
around a six-inch square space and mix a neat mixture of cement and pour
into the space so as to make about a quarter-inch layer. After this has
set for about fifteen minutes pull some of the neat cement up the sides
with a putty knife or strip of cardboard and then pour in the remainder
of the tile concrete mixture of one-third cement and two-thirds sand.
This will result in a tile with the top and sides surfaced with neat
cement. The surfaces of the bars and the glass or other under surface
have of course been properly oiled previous to the pouring.

BEFORE PROCEEDING WITH TILE MAKING it may be necessary to make a number
of plaster bars to use as retaining walls. These are made as follows:
Two strips of wood one-half inch to an inch thick laid parallel on a
glass or other smooth surface that has been greased with oil. The
distance between the strips of wood should be about ten inches, as the
length will then serve for producing eight-inch tiles or any size under
this dimension. The edges of the wood facing inward should always be
oiled, the wood strips are held in position by small lumps of modeling
wax pressed firmly into the outer edge of the wood so that it attaches
it to the surface of the glass. This will leave a channel between the
two wooden strips into which the plaster is poured. The two ends of the
channel may be stopped with blocks of wood or blocked with wax or clay.
As soon as the plaster is poured into the mold it should be evened by
running a straight strip of wood or metal over it spanning the width of
plaster. Run this back and forth to trim off the surplus, so that the
plaster will have an even thickness when removed from its bed.

TO REMOVE THE PLASTER first remove the wooden strips and then tap the
layer of plaster lightly on the edge with a hammer. This will loosen it.
Then with a T square and sharp nail mark off bars five-eighths inch
wide and also bars one and one-quarter inches wide. At least twelve bars
of each width should be made. After drying for three days the bars may
be sawed apart with any sharp saw, care being taken to hold the saw
within the groove made by the nail. The edges of the bars may be further
smoothed if necessary with a knife or file.

STRIPS OF WOOD WITH SURFACED SIDES can be used in the place of plaster
bars and if oiled will release very easily from the plaster when used as
retaining walls.

TO MAKE AN INCISED TILE in plain cement proceed as follows: Roll out
clay or modeling wax to about one-half inch thickness and cut to the
desired size of tile. Cover this smooth surface, place a design which
has been made on thin paper and trace with a pencil. The paper should be
held so as not to slip and the result should be a slight indentation of
the design on the clay. These lines are then incised over with the
incising tool to the desired depth, care being taken that no
over-hanging edges remain on the edges of the incisions. The incisions
should have sides slightly sloping inward and if the tool is correctly
shaped it will produce such lines.

THE DESIGN should be planned to be at least one-half inch from edge and
simple in construction. Avoid a tangle of ever crossing lines. A
geometrical arrangement dividing the square into pleasing spaces will
produce the best results.

Place the tile on a level surface and take four bars of the one and
one-fourth inch plaster strips or wood, soak in water for fifteen
minutes, wipe dry and oil. Now place the four bars so that the inside
edges are against the wax or clay tile and fasten so that they are
unmovable with modeling wax. The bars if placed with one end projecting
past the bar meeting it at right angles permits their adjustment to any
size tile under ten-inch dimensions. Onto this pour plaster-of-Paris,
pour into the center letting it run toward the edges forcing all air
ahead of it as it enters the incisions. Level off surface and remove the
plaster cast from the mold as soon as it has hardened.

TO RELEASE THE PLASTER CAST first remove the surrounding bars and lift
the plaster tile off the clay. The plaster tile will have the design in
relief on the surface. If any clay is adhering to these relief lines, it
is evidence that there are overhanging edges and such edges should be
trimmed with a knife before the next step. The next step is as follows:
After plaster tile is dry put it in water for a few minutes, then oil
the surface well. Place back in the bars and repeat previous operations
excepting that this time a cement mixture is used instead of plaster. A
mixture of neat cement should be used half way up and permitted to
remain for five minutes before the concrete (one-third concrete,
two-thirds sand) is poured in for the remaining half.

IN MIXING SAND AND CEMENT it should be remembered that they should be
mixed together thoroughly _while dry_ before any water is added. After
the cement has been poured into the form, if it is to be used for floor
or wall purposes, four small squares of cardboard should be pressed into
the exposed cement which is the back of the tile. This should be done
about fifteen minutes after the cement has been poured, when it is not
too soft.

The tile may be removed after it has remained in the form for
twenty-four hours. A thin cement mixture of another color may be made
and brushed over the tile and the surplus removed, leaving the last
color only in the incisions.

AN INTERESTING VARIATION is produced by cutting away the clay or wax
between the incisions of the pattern to the depth of one-half inch or
less, making a mold of this tile and in turn casting a concrete tile.
The result will be a surface with relief section and low spaces, the
relief being concrete and rough in texture.

These low spaces are then filled with a colored cement of another color,
or neat cement, and brought to the level of the relief surface. Such a
tile secures a pattern adaptable to tile walks, or any surface which is
subjected to wear, in that the design is not only a thin surface layer,
but a thick portion of color that will not disappear with the wearing of
the surface layer.

A SIMPLE METHOD OF MAKING TILE MOLDS is to cut a design from a thick
piece of cardboard or sections of a design, and glue these in proper
position to carry out a design arrangement. These pieces should be cut
with tapering sides so as to permit of proper “draught” or releasing
conditions when the plaster cast is made for mold purposes.

The pieces of cardboard should remain glued until dried to avoid the
moisture of the soft plaster moving the parts around.

WITHOUT THE USE OF COLOR a number of pleasing and varying textures can
be secured with plain cement, as the gray color of the cement has an
artistic quality, and it is well to become well grounded in the use of
cement before combining color with it.

SEVERAL WAYS OF USING PLAIN CEMENT FOR TILES beside those already given
are explained in the following descriptions. These are termed Traced
Cement, Burnished Cement, Scraped Cement, Concrete Tile, Cement and
Concrete Tile, Glazed and Dull Cement Tile, Glazed Relief Line Tile.

THE TRACED CEMENT TILE is made by pouring a half-inch mixture of
concrete (one-third cement, two-thirds sand) into a mold made with the
usual retaining bars of any desired dimensions. Over this concrete
mixture a layer of about one-quarter of an inch of sifted neat cement
mixed with water should be placed. At a certain degree of hardness this
layer of neat cement will yield to a slight indentation or traced
outline. This condition can be tested by touching the edge of the
surface with a pencil point to see whether it is too hard or too soft.
A good plan is to pour the mixture in the evening and it is generally in
right consistency to work upon on the following morning. The surface
should be nearly hard but still sensitive to pressure with a point.

HAVING PREPARED THE DESIGN on a piece of paper about the weight of
business writing paper, the design is placed on the surface of the tile
and kept in the same location while a blunt, soft lead pencil is traced
over the pattern, pressing firmly to create a good indented line in the
cement surface. The design for this work is best where the pattern is
easily expressed in lines or outlined forms. The forms can be increased
in strength by rubbing the pencil on the outer edge of the lines to be
slightly modeled in separate appearance. When the design has been
completely gone over, the tile is placed in water for several days,
after which it is dried and a thin coating of color wash (see chapter on
Surface Finishes) may be added to it which will further the pattern by
coloring the traced lines.

THE BURNISHED CEMENT TILE is produced by casting a similar tile to the
one made for the Traced Cement Tile and proceeding in the same manner,
excepting that the spaces between the forms are burnished smooth with
the dull pointed pencil or a smooth small stick. This results in some
parts being burnished or pressed down while others remain in slight
relief. A change in this is also produced by scraping the smooth surface
off between the lines in certain places instead of burnishing it. This
results in parts of the surface being of a different texture and also of
a little different color, as the scraped parts are different in both
these respects to the cement which has dried and remains untouched on
the surface.

A SECOND BURNISHED TILE EFFECT is to pour a layer of neat cement first
in the mold and a concrete mixture last. When this is hard enough to
remove, and still soft enough to work upon (the neat cement layer having
been in the bottom will dry with a dull finish and not a glaze finish
as when flowed on as a top layer) it should be removed and the design
traced upon this neat cement surface. If a leather tool or smooth hard
point is used, certain parts as desired can be worked upon, smoothed
down or pressed in, through the paper which will create a change of
surface texture.

THE SCRAPED CEMENT TILE is where either the top neat cement or bottom
cement layer has the design in line or form scraped out of the cement,
the entire design being produced without a plaster mold being used. A
sharpened nail or nut pick will make a good scraper and this scraping
and pressing is done on the cement surface direct and not through a
paper as in the two previous problems. This direct method of working
upon cement surface is considered more thoroughly and more extensive
applications made of it in the chapter on Carved and Modeled Cement.

THE CONCRETE TILE. Varying finishes may be secured in casting any cement
tile by the kind of aggregate used with the cement. A rough irregular
small crushed rock will give one kind of texture, while a round small
white gravel will give another and each change will present different
effects. Without going into extremes of finishes or having too many
changes in the surface of a tile, pleasing effects can be secured by one
to three changes of texture secured by putting different mixtures in
different parts. This may be done by mixing and applying with a brush or
spoon the different mixtures into the mold, placing the mixtures each in
their proper section of the mold. The whole is then covered with the
backing mixture resulting in the surface pattern appearing with the
changes after the tile has been released from the mold.

Where a concrete mixture is to appear rough in texture, the sand or
gravel and cement should be mixed dry, just enough water added to cause
it to mix up to a damp consistency so that it can be shaped with the
hand. This can then be put in the mold and tamped slightly with a block
of wood to press it in true contact with the surface of the mold. This
will result in a porous, open texture, producing good contrast with neat
cement parts that have been previously placed or are to be added.

THE CEMENT AND CONCRETE TILE is made with plain cement producing added
interest to the design by the two textures or surface finishes that
occur between cement and concrete. The design for such a tile is best
where the parts are separated either by an incision or a relief line.
The plaster mold should therefore present separate portions, some of
which can be considered for the cement parts and others for the concrete
parts.

By mixing neat cement until it is of a thin mixture, the mixture can be
placed on the mold wherever wanted by dripping it from a brush. Care
should be taken in the use of a brush with cement that a wiping stroke
is not used as such a stroke will remove the oil from the plaster
surface and cause parts of the cement to stick to the plaster.

After the cement has been placed, a concrete mixture is made and poured
into the space up to the desired height to produce the necessary
thickness. This will at the same time fill in the remaining surface
spaces of the tile.

THE GLAZED AND DULL CEMENT TILE is produced by filling in with clay or
glued cardboard bits cut to shape, those parts that are to be glazed
gray cement. Do not use modeling waxes or artificial clays for this part
as the oil or grease in them will interfere with the glazed cement
adhering to the surface in the final finishing.

After the cardboard or clay is dry a layer of neat cement is poured in,
and backed with the usual concrete mixture. After the tile is released,
the cardboard bits or clay is removed and cleaned out, the surface under
it is roughened with scratched lines and the tile is put in water for an
hour. The spaces are then filled with a mixture of neat cement and
permitted to harden in a shallow tray of water.

TO MAKE GLAZED CEMENT SURFACE it is important that these steps be
watched:

     1st. That the surface be roughened wherever the glazed surface is
     to appear.

     2d. That the tile be soaked in clean water until it has fully
     absorbed water.

     3d. That a little dry neat cement be placed on the spaces to have
     glazed effect.

     4th. That the neat cement should be sifted and dripped on with a
     brush and not gone over a second time.

     5th. That the tile is taken out and dried and the glazed and dull
     neat cement will create the change of surface texture as planned.

A bloom or chalk-like powder often comes on the surface of tiles, but
will disappear within a short time and need not cause any anxiety.

GLAZED RELIEF LINE TILE is made by casting either a neat cement tile or
a concrete tile with a relief line design and then mixing a neat gray or
color cement glaze and putting it onto the surface. The tile is shaken
in a level position until the entire surface is entirely covered leaving
a thin layer of the glaze in the spaces between the lines as well as
slightly on the lines. The tile is set in a shallow layer of water to
harden.

OTHER VARIATIONS IN TILE EFFECTS can be made by combining these methods
and with the use of color in these different methods described,
unlimited avenues are opened to the worker in color cement. It should be
remembered also that most of these methods of surface treatment are also
possible in other forms beside flat or tile surfaces. The student should
know these methods of working with plain cement and concrete as they are
the foundation of successful Color Cement Handicraft.

[Illustration: How to Make Color Cement Tiles]

[Illustration: Cement Tile Textures]

[Illustration: The Incised Tile]




[Illustration]

CHAPTER 4

Making
Vases and Bowls

[Illustration]


MAKING VASES AND BOWLS is a little more complicated than the making of
tiles, but by following the directions carefully it will be found that
once the process is worked out, it can be easily repeated.

FOUR DEFINITE OPERATIONS are necessary to produce a bowl or vase and
they may be termed as follows:

    1st. Making or preparing the original model.
    2d. Making the molding case from the model.
    3d. Pouring the concrete into the molding case.
    4th. Releasing the mold and completing the object cast.

THE FIRST STEP, making the original model, is as follows: With clay or
modeling wax build a form of the vase or bowl desired. The inside need
not be considered; that is, do not make the form hollow but build it
solid. Care should be taken to see that the contour is even and alike
when viewed from all sides. A templet cut from metal, wood or stiff
cardboard, will help in securing perfect contour if moved around on the
outside and corrections made accordingly. A false neck should be added
onto the solid form and part of the bottom of the mold scraped so as to
leave a rim or edge on the bottom. The form is then ready to make a mold
from it.

ANY VASE OR BOWL CAN BE DUPLICATED in cement by making a plaster mold
from it. The inside of the bowl should be filled with sand or wadded
paper and a false neck built over the mouth with clay or modeling wax.
If the surface is glazed it need not be oiled before casting, but all
dull or rough surfaces should be oiled.

THE SECOND STEP, making the molding case, is as follows: Take the model
(clay or vase to be duplicated) and place it upon an oiled glass or
other smooth surface. Marking off about one-third of its diameter, build
a narrow strip of clay or wax on two sides from top to bottom. This
ridge or wall should extend far enough out to meet the molding case or
metal strip, and the two walls of clay and the metal or case should be
made proof against the plaster running out anywhere, when it is poured
into this well. After the plaster is set, the clay strip can be removed
from one side and the exposed plaster edge is oiled after two keys have
been bored into it with a pointed metal strip (see working plate). The
removed strip is then built along the next division of the model and the
case or metal used for retaining wall is moved into new position and a
second third of the molding case is made. To make the third or last
piece of the mold the two first sections are retained in position
(always boring keys and oiling exposed edges), the case or metal wall
again placed in position and the plaster poured into the opening. The
plaster should not be too thin and if a little is poured into the bottom
and allowed to set before pouring the whole amount, it will not be
forced out through the bottom. Of course all openings must previously
have been stopped with clay or wax.

TO STRENGTHEN A MOLD strips of burlap or wire screening can be imbedded
in the plaster while it is soft. This makes a durable mold capable of
withstanding much handling.

TO MAKE THE MOLD FOR THE BOTTOM the three sections are turned upside
down (the model still being in position) and the plaster parts all being
oiled, a ring of clay is placed around the bottom so as to make a cup
shape into which the plaster is poured.

THE THIRD STEP is the most important part as the mixture or “slip” for
the pouring is important. The first mixture should be neat cement and
water and should be rather thick, for if too thin it will not adhere to
the walls of the mold. When the neat cement is ready it should be poured
into the bowl about half-way full. The bowl is then rotated in a
horizontal position gradually downward so that the surplus cement slip
will pour out of the mouth back into the pan or container in which it
was mixed. Then after a half-hour or so another mixture of slip should
be rotated. This mixture should be composed of a one-third cement and
two-thirds sand mixture and be thinner in consistency. If the bowl is
large and the walls need to be thick a third and fourth layer may be
necessary.

THE LAST LAYER OF SLIP can be of neat cement which will finish the
inside with a smooth surface. When working with color the first rotation
and the last may have color added to the slip which will result in a
color finish on the inside and the outside of the bowl or vase.

THE FOURTH STEP or releasing the mold, should occur the second or third
day after the pouring has taken place. This elapse of time depends all
upon weather conditions. In summer cement dries more rapidly and not so
well. In winter the hardening is more slowly accomplished but more
perfectly.

THE DRYING OF CEMENT is best when it occurs gradually. Never place
cement in the sun or use artificial heat to force it. Checking, cracking
and breaking will surely result if this is done.

For this reason the tiles and pottery made with cement should dry
gradually in the shade but not in a draughty location.

To release a vase or bowl from the mold, the cords are untied and the
plaster mold parts opened. The cement cast, if successful, will separate
from the mold without trouble. The ridge that may have been formed by
the groove where the plaster parts have come together can be scraped off
and smoothed by rubbing the finger tips over the surface. The surplus
part of the neck can be carefully scraped away and after the vase has
dried out of the mold for a day it can be put in a bucket or tub of
water to harden for a few days or a week.

TO FINISH A VASE it is removed from the water, permitted to dry well,
the surface is brushed clean and it can then be waxed or surface
finished as described in another chapter of this book.

A RELIEF DESIGN ON A VASE SURFACE requires care in making the sections
of the mold so that the vase cast will pull out of the mold without
breaking. If the molds are made in three or four segments there is
little danger of trouble but wherever there is relief surface or lines
on the surface, a two-piece mold is sure to result in the breaking of
parts.

DIFFERENT TEXTURES IN GRAY CEMENT can be secured on the surfaces of
bowls and vases by using almost any of the processes described in the
previous chapter for tiles.

IN ADDING COLOR TO DIFFERENT TEXTURES of cement in Cement Pottery the
color or neat cement can be added to the oiled surfaces of the plaster
molds before they are tied together preparatory to the pouring. In this
instance, however, the divisions of the plaster molds should be planned
so as not to break through the designs. If a continuous design motif is
essential, the only way to correct the break will be to touch in the
disconnected parts with the right color or mixture after the parts of
the mold have been placed together just previous to the pouring in of
the slip for the first rotation.

THE MAKING OF FLAT BOWLS simplifies the rotating problem and in many
shapes the slip can be placed and directed with the use of a brush.
After the last slip has been added to a bowl, a design can be added with
a brush by using a different color, placing the color slip in the center
of the inside portion of the bowl. This can also be done on the outside
surface of any bowl or vase, creating a change and surface enrichment.

VASES WITH SQUARE SIDES should be produced from plaster molds which have
the connecting lines coming on the corners. In this way the casting
lines that always show to some extent on the cast surface when it is
removed from the mold, will occur where it will be easy to remove them
and if a little does remain it becomes a part of the corner.

If any incised lines or relief parts are on the sides of these square
formed vases, a separate piece for each side will be necessary in the
plaster mold.

A GLAZED FINISH can be produced by rotating a bowl or vase in a mixture
of neat cement that has been well sifted and placed in a pan in a thick
enough layer to permit the bowl or vase to be turned in it without the
sides scraping the bottom of the pan.

WHERE LARGE RELIEF SURFACES are to be produced and undercut surfaces
molded, it is then necessary to use glue for the molds. This requires
skill in handling. For those who wish to produce molds for such work the
following is given:

After modeling the surfaces or figures in relief, if they are to be used
on garden pottery, book-ends, vases, etc., or any design that has
undercut surfaces, it should be covered over entirely with a one-half
inch layer or blanket of wet clay or modeling wax. If the modeling has
been done in clay it should remain overnight without the usual wet cloth
over it, before placing this second clay layer. If wax is used the clay
layer can be placed over it without waiting. Deep sections should be
lightly filled with clay to reinforce the one-half inch layer. Two or
three nails should be used to hold the original firmly to a board base.
A little plaster-of-Paris should be poured around its base to help make
it firm.

Over this clay blanket lay a strip of clay along the highest part or
equator of the surface, so that the surface is directly in line with the
equator. Place a casing around and fix so that plaster can be poured,
and a rough casing produced of one half. Remove the clay strips and with
a pointed piece of metal bore several holes or “keys” in the exposed
edge of the plaster. Oil this edge and cast the second half.

Before pouring the plaster a clay cylinder should be placed at the top
to form a hole for pouring into and a second hole near it for an air
escape.

After the plaster is set it will be found that a casing or shell is
produced which when placed over the original model (the one-half inch
clay blanket having been removed) will leave a space around the entire
original model.

The next step is to prepare the casings and pour the glue into this
space to produce a mold of the object and its immediate surface.

A few pencil marks are made on the outside of the casing and carried
onto the table or board base to check up its relation when it is
replaced. These marks are very necessary.

The casings are then given two coatings of shellac and wood alcohol (one
part alcohol, three parts shellac), and when dry are oiled well or
greased with axle grease. Shellac is also applied to the original model
whether clay or plaster. Plasticene or similar wax need only be oiled
slightly.

Replace the cases so that the two halves come together closely and so
that the marks on the outside lower edge correspond correctly with the
marks on the table. Stop the cracks on the casing with clay dipped in
plaster and bind over the casing in the same way (or with the use of
cords) to prevent the glue from floating the casing.

THE GLUE IS PREPARED as follows: White fish glue or gelatine glue is
washed well in water. Put in dry can, placing it in second pan of water
and boil until creamy in consistency. When the finger can be dipped into
it without burning, the glue is poured into the casing as follows:

A funnel of clay or wax is roughly made and the glue poured into the
opening of the casing, filling the space between the model and the
plaster casing.

Let stand for twelve hours. Remove casing and cut the glue shell along
the half-mark made by the equator division, cutting from the under side
through at one stroke. The glue can be lifted (as it will give) so as to
permit cutting from underneath. To cut from the outside will not produce
a clean cut.

With French chalk or talcum, chalk the inside of the plaster casing well
over the shellac and fit the glue shells back into each half. Then with
a solution of powdered alum and water (two teaspoonfuls in one-half cup
of water) brush the entire inner surface of the glue to harden the
surface. Let stand for one hour.

IF CEMENT IS TO BE USED, the glue must receive two coats of white lead
or varnish and left to dry two days. When plaster is used no white lead
or varnish is necessary.

Cement should be used thin and a thin layer produced by pouring into
this mold and revolving it so that a coating will stick to the surface.
After setting for twelve hours more is added and again revolved until
the desired thickness is produced.

Where the object is not to be hollow the cement is poured in solid and
left until hard enough to remove the casing and glue shell.

This sounds complicated but it is no harder than the usual recipe and if
you can’t follow a recipe or be interested in its result, then there is
no hope for you in Color Cement Handicraft.

A DIAGRAM ILLUSTRATING GLUE MOLDS is shown at the end of Chapter Two, on
The Making of Plaster Molds. A little study of this with the above
directions will make the process clearer.

[Illustration: Vase Molds]

[Illustration: The Finishing of Cement Pottery]




[Illustration]

CHAPTER 5

The Use of Color in
Cement Tiles

[Illustration]


SUCCESSFUL COLOR IN CEMENT WORK is dependent entirely upon the use of
mineral pigments in dry powder form. The lime action in the cement will
nullify and disintegrate any color of a vegetable or chemical source so
that no hue remains.

A LIMITED RANGE OF COLORS is therefore presented to the worker in Cement
with which to secure results, but the list of colors described in the
following paragraph is after all an elaborate one when compared with the
few pigments with which the primitive and aboriginal potters produce
most beautiful results in their wares.

PICTORIAL OR REALISTIC DECORATIONS ARE NOT DESIRABLE as Color Cement
decoration and it is hoped by the authors that those who follow the
technical direction of this book will be in harmony with the applied
design principles set down in the last chapter; and that their color
cement productions will be such that it will add correct line, form and
color to this new handicraft. This will enable its growth among the art
handicrafts to be without handicap or prejudices resulting from its use
in incorrect design or application.

THE FOLLOWING COLORS ARE POSSIBLE in mineral colors for us in Color
Cement: Black, Brown, Red, Dull Yellow, Blue, Green.

A Color Scale and Mineral Colors are as follows:

                { Germantown Lampblack
Black or Gray   { Carbon Black
                { Black Oxide of Manganese
                { Black Oxide of Copper

Blue            { Ultramarine Blue
                { Oxide of Cobalt

Yellow          { Yellow Ochre
                { Chromate of Lead

Orange            Mineral Orange

Green           { Chrome Oxide of Copper
                { Carbonate of Copper
                { Roasted Oxide of Iron
Brown           { Burnt Umber
                { Metallic Brown

                { Indian Red
Red             { Venetian Red
                { Mineral Turkey Red
                { Raw Iron Oxide

THE SUCCESSFUL USE OF COLOR IN CEMENT depends entirely upon the true
proportion of color to the cement. No exact rule can be quoted as colors
vary in quality in different localities. Experimenting only can solve
the correct proportions. Also, anything that will nullify the action of
disintegration upon the color by the lime in the cement is desirable.
The Petroma Cement Colors made by the American Crayon Company of
Sandusky, Ohio, fulfill these requirements for the craftsman, and will
aid in successful schoolroom results, avoiding loss of time and waste of
material.

COLORS MAY BE GLAZED, MAT OR DULL FINISH according to how and when it is
placed on the cement tile. Each finish requires different treatment and
the easiest is the Dull Finish.

THE DULL COLOR FINISH is produced when the color is dropped or placed
into the mold and concrete or cement is used as a backing. This results
in the color drying in the mold with a dull finish next to the plaster
mold surface and is exposed when the cement casting is released from the
plaster mold.

THE GLAZED COLOR FINISH is more difficult to produce successfully and is
secured only in that color that is placed onto tile or pottery surfaces
after the cement surface has partially hardened. A tile design or
pattern may be cast in a mold and after it has come out of the mold it
is dried for an hour and then placed in water. If the surface to receive
color has been roughened or lines scraped into it when first released
from the mold and the cement slightly soft, the color will adhere even
more surely. We know that metal craftsmen often roughen the surface of
metal where enamels are to be placed and fired in, to insure more
perfect attachment, and a similar treatment to the cement will do
likewise for the cement color. When the cement tile has been removed
from the water and surplus moisture shaken off a little plain neat
cement is placed on the surfaces to be colored and to this the color in
thin paste form is dripped from a brush. No back stroke is possible
without injuring the finish. Finish each section and then leave it
alone.

A SAFE WORKING METHOD is to place the tile in shallow water to avoid any
part becoming dry while the color is being applied. A pan or shallow
dish will serve the purpose.

THE MAT FINISH is produced the same as for the Glazed Finish excepting
that the tile is placed in water immediately after it is removed from
the mold and placed there for a few minutes only. The surface is treated
otherwise similarly to the glazed process and this results in the color
being dull in finish.

HARDENING IN WATER should be done with all tiles and the dull and glazed
finished tiles should be set in a pan of water without letting the water
reach the decorated surfaces.

A COLORED SKETCH should be made in every instance where color is to be
applied to cement.

MATERIALS FOR MIXING COLORS are as follows: Two sizes of small
sable-hair brushes, a palette knife (or putty knife), several small
dishes, a spoon, a fine-mesh sieve, and a piece of glass.

TO MIX THE COLORS proceed as follows: Place a little of the desired
color on the glass, to this add dry cement reducing the color intensity
to the desired strength. Portland cement being gray will do this
harmoniously. To this add a few drops of water until the color is of the
desired consistency.

The color should always be tested on a tile surface and dried in the sun
to determine final color, adding color or cement to the wet mixture to
correct the color. Where a tint of color is wanted a white cement should
be added instead of Portland cement.

To produce a plain surface color on tiles, the desired quantity of color
is mixed and strained, to eliminate all coarse particles. The mixture
may be sifted while dry or strained after the cement has been added.

THE USE OF WHITE CEMENT should be limited because white cement is not as
durable as gray cement and because its setting qualities disappear as it
becomes older more rapidly than gray cement. If perfectly fresh it can
be used with good results and produces a more brilliant color when mixed
with the colors than when gray cement is used.

TO APPLY THE COLOR either in the mold or to the surface of the object
after it is removed from the mold, the color should be applied with a
brush.

AS A TEST COLOR PROBLEM use an incised pattern plaster mold and the
colors may be planned for the incised tile as follows: Working from a
color sketch, mix up colors to match and after the plaster mold has been
water soaked it should be oiled by dabbing the brush up and down on the
surface. If the brush is stroked it will not leave enough oil on the
surface and the color will stick to the tile. Next drip the cement color
from a brush with a shaking motion. The various colors are thus placed
in each of the partitions of the mold and after drying for fifteen
minutes is backed with a layer of plain cement and sand and allowed to
set.

When the tile is released it will contain different colors between the
incisions and a thin wash of an additional color may be added to fill
the incisions.

COLORS CAN BE MIXED one with another while dry or when wet to produce
other shades. Violet will be produced by the mixture of mineral orange
and ultramarine blue.

PLAIN SURFACED TILES MAY BE COLORED by pouring in a thin layer of color
combined with neat cement and then backed up with a concrete mixture.
Mottled and variegated color surfaces may be secured by first spattering
or dropping drops of another color into the mold before the color
mixture is poured in. Or the plain cement or concrete tile can be
removed and covered with a color layer which will be dull or glazed in
finish.

A PLAIN TILE TO BE APPLIED WITH COLOR should be placed in water
immediately on being removed from the mold, and allowed to remain there
for a quarter of an hour, before applying the color. When taking the
tile out of the water do not let the fingers come in contact with the
surface to be colored. Let the tile stand a few minutes to drain, before
applying the color. Then a thin layer of neat cement mixed with water is
applied. Next place a spoonful of the color upon the surface of the
tile, slightly shaking the tile while level, then pour off the surplus
color as it overflows the edges. If bubbles occur the surface should be
recoated for the bubbles will break in the drying, producing a defect.
To prevent bubbles, the color should be stirred with the spoon slowly so
as to avoid the arresting of air which produces the bubbles. The point
of a pin will often help to dissolute the bubbles if used immediately
after the surface is coated. When satisfactorily coated, place the tile
carefully in a tray and add water until it reaches a little more than
half way up the side of the tile. Be careful that water is not splashed
or dropped on the newly coated tile, for this will ruin the surface and
necessitate doing the tile again. The tile should remain in this water
for four or five days, water being added when it has become absorbed or
evaporated.

TO COLOR AN INCISED DESIGN the plaster cast from the original becomes
the mold for the color cement tile. The plaster, having become
thoroughly dry, is shellaced with one or two thin layers of shellac and
after drying for one or two days is ready for use with color cement.

It is then oiled well but not so that surplus oil remains on the
surface. A dry brush will be good to use for removing surplus oil. The
color having been mixed to harmonize with the previously prepared color
sketch, one of the color mixtures is taken up with a brush and dripped
with a shaking motion onto the correct area, which in an incised design
is divided into spaces. If a drop of color falls where it is not wanted,
take a clean brush and pick the color out of the space, after which a
little oil should be brushed carefully into the space to renew that
which was removed with the misplaced color. If any color falls onto the
back of color already placed do not worry over it as it will not appear
on the finished surface.

ANY COLOR NEXT TO A FILLED SPACE may overlap the previously filled space
as only that color touching the plaster surface will be visible when the
tile is removed from the mold and is finished.

AFTER COVERING THE ENTIRE SURFACE WITH COLOR let it remain for half an
hour before backing it up with the concrete mixture, as otherwise the
weight of the concrete may force gravel particles through the thin color
deposits and mar the face of the color design.

TO COMPLETE THE TILE remove after two days, and place in water after the
edges and slight faults have been corrected. It should harden in water
for several days and then dry in a cool place after which it can be
waxed or finished in other ways.

ANY OF THE PREVIOUS PROBLEMS described in the methods for producing
tiles in plain cement can be carried over into this chapter and color
added to the texture finishes in cement and concrete and many
interesting finishes developed.

OLD COLOR AND CEMENT or dried cement color should not be used. Mix up
only enough color for immediate use as any color not used fresh after
mixed with cement cannot be used again and should be discarded.

[Illustration: Use of Color in Cement Tiles]

[Illustration: Color Tile Methods

    1. Relief Tile.
    2. Persian Relief.
    3. Relief Line with Mold Color.
    4. Relief Line, Majolica Color.
    5. Intaglio Tile.
    6. Sgraffito Tile.]




[Illustration]

CHAPTER 6

Color Cement Relief
Tiles

[Illustration]


TO BEGIN A RELIEF TILE, a model should first be planned on clay or
modeling wax. A pencil pattern is first made on paper and this paper is
placed over the layer of clay or wax and a pencil tracing will produce
an indented pattern of the subject on the clay or wax underneath.

TO MODEL THE SURFACE a wooden modeling tool, such as is used by
sculptors, or a leather modeling tool or even small whittled pieces of
wood can be used. In producing raised portions the clay or wax scraped
to produce low parts can be used and care should be taken not to produce
too great a relief as a tile design should not appear detached.

AVOID UNDERCUT SURFACES or overhanging edges on the finished model as
this will result in locking of the cement cast with the plaster mold and
breaking of the tile before it can be removed. A general checking over
of the different parts before the plaster cast is made will avoid many
of the overhanging parts going through as they can be easily located and
corrected.

TO CAST THE PLASTER MOLD the clay or modeling wax is surrounded with the
retaining bars and as the clay or wax needs no oiling the plaster can be
mixed and poured into this mold. A slight jarring of the table or
surface on which the mold is placed will cause the plaster to settle,
producing a level surface and also cause any bubbles to break or come to
the surface.

TO AVOID BUBBLE DEFECTS IN CASTING either with plaster or cement the
plaster or cement mixture should be poured into the center location of
the mold allowing it to spread gradually toward the sides and corners
carrying the air in the grooves and low spaces, forcing it toward the
edges. Once the surface is covered in this way the remainder of the
mixture can be poured in more rapidly.

TO CORRECT BUBBLE DEFECTS that appear on the finished plaster or cement
casting, scrape some of the plaster or cement from the back or sides
where it does not matter and repair the flaws by pressing it into the
holes. Where cement is repaired this way it should be permitted to dry
for another day before it is placed into water to harden.

TO MAKE THE CEMENT RELIEF TILE in color the plaster cast made from the
clay or wax model should be oiled after it has been shellaced and
surrounded with the retaining bars. The color should be then mixed with
the cement and water added to make it of a pouring consistency, it is
then poured into the mold. After this color has set for awhile the back
layer is added of concrete after the color of the first pouring has been
carried up so as to produce color on the sides as well as on the face.

WHERE A NUMBER OF COLORS ARE USED the colors are mixed and dripped upon
the oiled surface of the plaster mold before it is enclosed with the
retaining bars, as the retaining bars would prevent free access to the
surface with the brush. After the various colors have been placed, the
plaster cast is then placed within the bars and the color being
permitted to set, it is then backed with a layer of concrete.

THE CONCRETE BACKING MAY BE COLORED either with color throughout or with
a topping of color to give it a finish. If corners are to be rounded or
the edges trimmed in any way this color layer should be thick enough to
permit trimming without exposing the under layer.

TO AVOID THE COLOR FALLING OUT in color relief work, the following
should be observed. When preparing to pour in the backing, observe
whether any of the color cement placed on the tile has become too dry.
If so, it should be sprayed with a light coating of water or brushed
with a brush full of water, and its upper exposed surface slightly
roughened so that the backing will adhere firmly. If it becomes dry and
smooth the second layer of cement poured onto it will come in close
contact but not adhere, and later a change in temperature or jar of the
tile may shake a portion of the design loose so that a color fragment
will fall out.

TO AVOID COLOR PREMATURELY DRYING, the plaster cast should be placed in
water for fifteen minutes at least before the color is placed into it.
To permit free absorption of water the plaster tile should never be
shellaced on the bottom but only on the sides and the top.

ANOTHER WAY TO MODEL A RELIEF DESIGN is to carve it on plaster direct
without making the relief on clay or modeling wax. This method has the
advantage of being proof against overhanging edges, though some care
must be taken against undercut surfaces.

TO MAKE THE PLASTER CARVED MODEL trace the design onto a smooth slab of
plaster of the right size that has been cast on a smooth surface. If a
larger piece of plaster than the desired size is used it can be cut
down.

TO CUT PLASTER SECTIONS an old saw can be used or several strokes of a
knife on the surface until about one-quarter of the thickness has been
cut, and a similar cutting on the reverse side, just opposite to the
cutting on the first side will enable the plaster to be broken easily.
Or by laying it on a straight edge with the line of cutting over the
edge, a quick pressure with the hand will snap the two pieces apart.

AFTER THE DESIGN IS TRACED a chiseled nail point, nut pick or other hard
edged point is used for scraping the surface of the plaster, modeling it
or carving it to the desired shapes. Naturally it will be found that
plaster can only be taken off and not added on and that all reliefs
must be produced from the surface downward, that is the natural surface
will be the maximum height and all variations in the surface produced
below that.

BACKGROUND TREATMENTS are produced where a design appears in low relief
against a background. The background may be stippled with the tool point
or lines scraped or crossed lines used to create interesting background
qualities.

TO BUILD UP PLASTER SURFACES, roughen the surface onto which more
plaster is to be placed and mix fresh plaster and place it on with a
small spoon or with the brush. After this is dry it can be carved or
scraped with the tools used in the modeling of plaster.

TO FINISH THE PLASTER CARVING, it is dried, shellaced, and used for
casting just the same as the other relief forms described. To preserve
casts from receiving injuries to their surfaces they should be wrapped
in paper with a card against their face and placed with face toward the
wall in a cupboard or shelf, when not in use. Where a mold has been
repeatedly used and the shellac become worn, the mold should be
carefully dried and the shellac coating renewed.

A CONVENIENT CLAY TO USE for relief work is the powdered fire clay
secured in most hardware stores and is the clay used for lining grates,
furnaces and similar purposes. This clay is convenient in that only the
amount needed may be mixed up for use, leaving the balance of the
powdered fire clay always in good condition.

RELIEF TILES DESIGNED FOR FLOOR SURFACES or for wall surfaces are best
where they do not contain deep relief as they will not catch dust or
dirt and will be better unified with the remaining surfaces.

SPECIAL TREATMENT FOR RELIEF FLOOR TILES is required in that the cement
should be compact and clean sand should be used mixed with just enough
water to cause the two to adhere to each other and this should be
tamped into the mold well up against the face of the plaster tile to
pack the mixture firmly and cause it to form into a durable surface.

TO HARDEN CEMENT TILES or pottery they should be placed in water so that
the water will complete the chemical action producing the stone-like
quality of successful cement work. If the tile is removed and dried and
again placed in water it will increase the hardness.

AFTER THE TILE IS HARDENED it is dried thoroughly and brushed well with
a brush. It may be waxed or first given a thin coat of shellac and then
waxed. Shellac should never be applied until the cement tile is
thoroughly dry, as otherwise the shellac will remain sticky.

[Illustration: Plaster and Clay Modeled Cement Tiles]

[Illustration: Color Cement Tiles and Pottery by Art School Students]




[Illustration]

CHAPTER 7

The Majolica Tile

[Illustration]


MAJOLICA POTTERY derived its name from the island of Majorca, Italy,
where during the sixteenth century glazed pottery reached its highest
perfection.

Glazed color may be placed in hollows in the surface of pottery or on
the surface. A better method is to produce a raised line or rim to
retain the glaze, and this is the method we will use in the cement or
concrete pottery.

THE CEMENT MAJOLICA TILE is made as follows: First design a subject that
will have each motif, part or section defined with lines. These lines
must be part of the design and used much as lines are used in stained
glass work. The design should be simply planned. A confusing
overcrossing tangle of lines is to be avoided. A few geometrical forms
rightly related will be most pleasing. Keep the design at least one-half
inch within the edge of the space. Then oil a piece of glass as
directed, place over a card that has the tile dimensions squared off on
it as a guide for placing the casting bars on the glass. Clay or wax
should always be used to hold the casting bars in place. Into this now
pour plaster-of-Paris, pouring into the center, letting it flow to the
outer edge. Level off evenly and remove after fifteen minutes. On
releasing this plaster tile a smooth surface will be found on the side
which came next to the glass.

THE DESIGN is then transferred to the plaster tile by tracing with a
carbon paper. The paper should be thumbtacked onto the sides of the
plaster tile to prevent it from slipping while tracing. The design
should also be traced on backwards so that the completed majolica tile
will be in the same position as the design. The design is then incised
with the incising tool, care being taken that at whatever depth the line
is made the incision has sides sloping upward. If these grooves have
overhanging edges the cement to be poured in will flow under these edges
and lock the tile, causing these lines to break before the cement tile
can be released.

WHEN INCISING, see that the bottom of the groove is sufficiently wide,
as this bottom is to be the surface of the line on the completed
surface. A line one-sixteenth or one-eighteenth of an inch is not too
wide. The plaster should not be too soft or too hard to secure the best
incision and avoid crumbly lines. When the incising is completed oil the
surface and surround the tile with four retaining bars. The bars should
be soaked in water and be of double width as they extend above the
plaster cast. This extension above the tile represents the thickness of
the tile to be made. Clay or wax is pressed on the outer edges of the
bars and plain neat cement or a mixture of the desired color is made and
poured onto the mold. Pour in the center steadily, for cement poured on
the “installment plan” will show a mark wherever each installment
occurred.

When the cement in the mold has dried for twenty-four hours remove by
slightly prying, after the retaining bars have been removed. If parts of
the lines are not on the surface it is because air was arrested in
pouring the cement or the oil settling in the grooves. If lines are
broken and remain in the mold it is because the grooves have overhanging
edges and locked the cement line. To repair these lines, soak the tile
for a few minutes and mix a small portion of cement to match that used
and build the missing section by dripping the cement from a brush.

AFTER DRYING for an hour put the whole tile in water for a day or
overnight and it is then ready to add the color. Meanwhile the plaster
mold with the defective grooves should have the grooves cleared by
scraping the overhanging edge with an incising tool.

The tile as it has been produced by the mold appears with a number of
relief lines dividing the whole surface into a number of partitions or
cells. It is into these that we are to place the color and it should be
worked as follows:

While the surface of the tile is moist, drip in the color with a brush,
spreading it to fill the required space. Thin pieces of metal (or
material that will not absorb the moisture) may be used to spread the
color, producing a smooth, even surface. The color after once commencing
to set should not be touched, and for this reason should be rather
liquid so as to permit handling without too rapid drying.

THE COLOR SURFACE appears better when the lines of the design remain
uncovered with color. If the color is thickest in the center of the
spaces and then bevels down as it comes in contact with the lines, the
whole tile or surface will appear more professional.

If color becomes blurred or disturbed, it is better to wash the whole
out under the faucet and begin anew, or remove the section at fault and
work over. No amount of patching or rubbing will perfect the surface
after it is partly dry or completed.

After the coloring is finished put in a tray, carefully pour water into
the tray without dropping any onto the tile and let harden for five
days. The water should reach a little more than half-way up the side.
After removing it from the water let stand until dry, polish with a soft
flannel slightly waxed to remove white sediment on surface.

ANOTHER METHOD WITHOUT THE LINES is to use the color directly onto
cement or concrete surface without any retaining lines. The colors may
be placed so that they intermingle or so that they just touch, or the
color spots may be separated one from another similar to stencil work.
The color for this method is mixed thoroughly with cement and water
until the mixture is a fine thick liquid or “slip.”

SLIP PAINTING is a method of painting a design in one or several colors
over a cement or concrete surface. The color may be slightly in relief
or if done at the proper time it can be made to become a flat stain of
color sinking into the first surface.

THE TWO WAYS OF SLIP PAINTING must be handled a little differently and
the best way to become familiar with these methods is to do the work.
Therefore let us work out the first method of producing a design slip
painted in slight relief as follows:

FIRST: Make a design for a six-inch square, the design to denote the
colors to be used. Second: on a glass place retaining bars which have
been soaked in water and oiled, leaving space six inches square into
which a half layer of neat cement is poured and then a layer of one-half
sand and one-half cement. Third: after standing for twelve hours,
release this cement tile and it will be a plain, smooth surface. This is
placed in water for an hour and the design traced upon its surface.

Chalk of any visible color should be rubbed on the back of the drawing
to act as a tracing medium. Carbon paper or graphite should not be used
as any greasy substance will prevent the slip painting from adhering to
the cement tile surface.

THE COLORS FOR THE SLIP PAINTING should be mixed so as to match the
colors of the color sketch. When matching the colors, dry a small dab of
each color on a glass to see the dried color effect.

TO MIX THE COLORS PROPERLY, select the color you wish, emptying a little
upon a glass or marble slab. Take a little clean water and mix with a
palette or putty knife and grind the color until it becomes a thin
liquid paste. Having ground this color thoroughly, scrape it up and
place on one side of the glass, then proceed with the next color until
you have mixed the complete palette of colors to match those on the
sketch.

VARYING COLORS CAN BE SECURED by mixing the mineral colors and where
hues different than those in the set are wanted they should be mixed the
same as in water colors. There is one exception to this rule and that is
in using the orange. The orange in the mineral colors when mixed with
blue will produce a violet.

To gray the colors add gray cement, and to lighten the colors add some
of the white cement.

TO PLACE THE COLOR ON THE TILE, take it up with the brush and drip onto
the cement surface, being guided by the tracing previously made. The
color should be thin enough to flow from the brush easily and not so
thick that it drips in lumps. More water should be added if too thick
and more color is added if too thin. In both instances, whether water or
color is added it must be ground in thoroughly. If the color settles on
the glass it should be stirred again to keep the mixture uniform.

THE RELIEF OF THE COLORS can be regulated by how much color is flowed
from the brush, and surfaces can be built up by repeating the strokes of
color. Avoid repeating a stroke after the color has commenced to set, as
a second stroke in such an instance will destroy the surface lustre.
Where colors run over the boundaries they may be scraped back or taken
off with a moist, clean brush.

The direct clean stroke will produce the best final results, and if
preceding each stroke a little thought is given, mistakes will be
avoided.

The tile surface should not be permitted to dry while working upon it
and if kept in a shallow tray of water there will be less risk of it
doing so. Water should never be permitted to fall upon or touch the
surface of the slip painting or tile as the color will be destroyed. The
tile is placed carefully into shallow water to continue hardening and in
four or five days will be hard enough to remove. After drying out of
water several days it is ready to use or it may be given a gasoline wash
or wax rub if needed.

Tiles will harden as they age. Those that appear to be partly chalky
when completed will harden in a month’s time, when the moisture from the
center of the tile has completely evaporated.

THE SECOND METHOD OF SLIP PAINTING is used where three different planes
or heights of color are wanted. For instance we will suppose that the
subject is to be a decorative design of trees and distance landscape in
three colors. This would be worked out as follows: First, cast a plain
cement tile and after removing it and while damp pour a spoonful of
color on the surface coating it with plain color as desired. This color
should be the background color of the sketch. Second, while this coating
is soft, take the lightest color (for clouds, water, boats, flowers,
etc.) and with a full brush place the color onto this soft coating. It
will blend and sink into the background color and remain equally flat.
Third, after these colors have commenced to set, with a full brush paint
in the foreground part of the design (trees, etc.), working in large
masses and building up the color by repeated strokes until the right
relief is secured. Avoid shading the parts and keep all parts flat in
tone, even though they may be in relief. It will be found that the later
color is added to the first coating the less it will sink into the
background. Any design can be worked out accordingly either in relief or
flat. A little experimenting will solve many questions, and reveal
greater possibilities. To complete the tile it is placed in shallow
water until it hardens, then let dry for several days after which it may
be given a toning wash, or gasoline wash, and a wax rub.

A THIRD METHOD is to take a flat surface and slip-paint a design onto it
in relief. After the color has set for a short time it can be trimmed
carefully with a knife so that the sides are nearly vertical. This will
give the slip-painting a decidedly different appearance and it may be
left this way or other color may be added so that it comes nearly up to
these trimmed sides.

AVOID LEAVING ANY PART OF THE SURFACE DRYING or setting when painting on
the surface; or the tile hardening in the water too long before being
painted upon, as it will prevent it from becoming durable. Surfaces can
be covered smoothly when slip-painted if the color is used very thin.
First cover the surface with a coating of the color to be used,
immediately adding more of the color and it will flow and settle evenly.

A slip-painted color will dry dull if placed upon a tile shortly after
it has come out of the mold. To secure a glaze to a color the tile
should remain in the water for two days before the color is placed onto
it.

FOR LARGE SURFACES on which color is to be slip-painted, the surface on
which the color is to go should be roughened, so that the color will
become anchored.

THREE DEGREES OF SURFACE can be secured by different treatment. These
finishes are, first, Dull Surface; second, Mat Surface; third, Glazed
Surface.

DULL FINISH is secured by putting the color into the mold. The mold
absorbing the water from the surface causes it to dry dull.

MAT FINISH is secured by placing the color onto the tile or vase surface
after the surface has come out of the mold and moistened in water for a
few minutes.

GLAZED SURFACE is secured by letting the tile or other object harden in
water for several days and then draining off the surplus water, after
which the color is slip-painted onto the desired surfaces.

TILE SHOULD NOT BE PERMITTED TO DRY at any time before color is added,
as the color will not become attached to the surface.

DO NOT FORGET to roughen the surfaces of the spaces and to add neat
cement also before dripping the color onto either the mat finish or
glaze finish tiles as described in chapter five in the paragraph on The
Glazed Color Finish.

[Illustration: The Majolica Tile]

[Illustration: Slip-Painted Tiles]

[Illustration: Slip-Painted Tile Methods]




[Illustration]

CHAPTER 8

Sgraffito
Color Cement Work

[Illustration]


SGRAFFITO is the name applied to the incised ware of the Italians, and
used by them from a very early period dating as far back as the twelfth
and thirteenth centuries. The ware was made by covering the clay body
with a layer of slip of another color, and this was then scratched
through with a tool showing the color of the ware beneath against the
superimposed surface, after which it was fired. This process has been
used from the most primitive times, but it remained for the Italians of
the fifteenth century to dignify it as an art.

COLOR CEMENT SGRAFFITO is produced with a layer of cement and color
being used instead of colored clay and the cement is hardened without
firing, water only being used to finish the surface to a durable
quality.

THERE ARE TWO WAYS to produce a sgraffito surface on a tile and these
are, the glazed surface and the dull surface tile. No mold is needed for
the design as a sgraffito design must necessarily be a freehand
production, though molds may be used for duplicating the sgraffito
effect after the original one has been made, if no undercut edges are
left.

TO PRODUCE A SGRAFFITO TILE, the retaining bars are set to give the
desired shape and dimensions, after which the space is filled with a
half inch layer of concrete, either of sand and cement mixture or of
gravel and cement. When this layer has dried so that the top section is
moist but firm in surface, a thin layer of color and cement should be
poured onto the cement so that it forms a thin layer not more than an
eighth of an inch thick.

TO SMOOTH THE LAYERS after the color has been poured in, shake the glass
or table or whatever surface the mold is resting upon and if this is
done gently it will cause the color to become level and even in surface
finish.

TO CAUSE TILES TO BE EQUAL IN THICKNESS the surface of the glass or
table upon which the mold rests should be level when the cement is
poured in. Otherwise the tile when finished will be found to be thicker
on one side than on the other. A glass or pan of water or a spirit level
will quickly show whether or not the surface is level.

AFTER THE FIRST COLOR LAYER IS POURED into the mold it is permitted to
stand just long enough to settle firmly and then a second layer of
another color is poured over the first layer so that it also forms a
thin layer of even color. This second layer should be even thinner than
the first. A layer one-sixteenth of an inch is a good dimension to plan
on, though these dimensions need not be accurately adhered to. If the
first layer is permitted to dry too long before the second layer is
added the result will be that as the finished sgraffito tile is drying
it will split in layers, the split coming between the layers of colors
that were permitted to dry too long.

A THIRD LAYER OF COLOR may be added over the second layer if the design
being planned calls for three divisions of colors. These layers are to
respond to the next step in the process, which is to expose portions of
each layer by tooling the surfaces so as to produce different colors at
the same time that the different depths are produced.

THE TOP LAYER WILL DRY WITH A SMOOTH SURFACE which will produce a
sgraffito tile with a glazed or partly polished surface while the other
layers will have a surface with dull texture.

TO PRODUCE A TILE WITH A DULL SURFACE throughout, the pouring stages
should be reversed in their steps. That is, the color that is to be the
top surface should be poured first and the other colors in their proper
relation, the last layer being the cement and sand or other concrete
mixture. This will result in the layer first poured in coming next to
the glass, having a dull finish when it is released from the mold.

TO PRODUCE THE SGRAFFITO DESIGN on the sgraffito tile, the tile should
be permitted to dry for about ten to twelve hours or if it remains
overnight the surface will be about right to work upon. The paper with
the design is then placed and retained in the correct position on the
cement tile and a dull pencil is used to trace the pattern, without the
use of carbon paper or other transfer medium. This will result in an
indented or embossed guide line on the cement surface of the tile which
can be used in scratching away through the first layer to the under
color.

THE TOP LAYER OF COLOR should be used to tell the main part of the
design story. If the subject is to be that of a bird or a ship, the top
layer design should be the bird or ship or other motif and the motif
should be so designed as to reach the boundaries of the tile surface so
as to produce a strengthening border arrangement all around the edge.

THE SECOND COLOR LAYER can then play a secondary part in both the color
scheme and the design arrangement, giving with its color placing a
contrast to the upper main layer used for the design.

THE BACKGROUND COLOR should be brilliant or dull depending upon the
surface color. If the surface color is brilliant, the bottom color
should be duller. If the upper color is dull, the background color can
then be the bright intenser color.

WHERE THREE LAYERS OF COLOR ARE USED the middle layer can be a color
harmonizing with both the background layer and the top layer and can be
used either for a pattern part to the design or it may be used simply as
a blending strata or layer appearing in the cut sides of the sgraffito
work.

COLOR HARMONY is essential in producing sgraffito color cement and a
color sketch will be a good safe preliminary in doing sgraffito work as
false steps or errors cannot be remedied in sgraffito and each step
should be carefully thought out before the tooling commences.

TO DO THE TOOLING, a scratch point should be used for incising or
scraping down along the line of the portion to be scraped out. The
portion within this boundary should then be scraped out down to the next
layer of color, care being taken not to gouge or cut deeply into the
under color. If the design is one of three layers, the center layer can
be included in the scraping out if the bottom color or layer is to
appear in that portion of the design. Do not attempt in the scraping to
take out large portions at a time as it will result in the breaking out
of sections that are wanted as part of the remaining design. It will be
found that the layers of color as scratched into retain their separate
layers and that the thin layer of the upper color separates easily from
the layer on which it rests. If a slight portion of the upper color is
inclined to remain attached to the background color or under layer let
it remain as it will give an interesting color quality and harmonize the
two colors.

THE SIDES OF THE SGRAFFITO LAYERS should gradually slope outward, and
after the layers have been tooled clear the sides of the layers should
be gone over and evened up in slant as well as in general finish. If the
corners are to be sharp or rounded in finish, see that the treatment is
carried out similarly in all parts so that a general unity of finish
will remain.

THE LAST STEP IN FINISH is to place the sgraffito tile in water so that
it is entirely immersed, and it is left in the water for several days
after which it is dried by being placed flat in a cool but not draughty
place to dry.

TO PRODUCE SGRAFFITO SURFACE on bowls or other round surfaces the layers
are produced by rotating the bowl in colors or spraying the colors on
with a sprayer such as is described in the chapter on coloring of bowls
and vases. The color can also be placed on with a brush if it is mixed
to the right consistency and the successive layers put on at the right
intervals.

SGRAFFITO FOR ARCHITECTURAL WORK holds great possibilities, and is being
gradually recognized by those builders who desire the charm of hand
wrought enrichment that graces so many of the Old World buildings.
Sgraffito decorative pillars and panels for buildings, homes and courts
is an assured possibility by the use of color cement and can be produced
with less cost than by the fired clay method as well as in larger, more
unified sections in that there are no kiln limitations to be considered
in doing the color cement. A plate is shown illustrating the use of
sgraffito in the making of an entrance to a college building designed in
the Italian Renaissance style and the sgraffito and ornamentation being
of Italian source, both combined in perfect harmony with the building as
a whole.

SGRAFFITO CAN BE APPLIED TO MANY FORMS such as book ends, fern boxes,
garden bowls, the requirement for success being mainly the placing of
the successive layers of color on each other when neither too dry or too
wet, and the scraping away of those parts desired when the cement is in
the proper condition.

[Illustration: Sgraffito Tile and Sgraffito in Architecture]




[Illustration]

CHAPTER 9

Modeled and Carved
Color Cement

[Illustration]


FROM A STANDPOINT OF GOOD DESIGN modeling, when applied to a flat
surface or any other surface, should not be high in relief.

Any time that a modeled design appears to have been added onto or is in
such relation to the surface that it appears to be an independent,
detachable ornament to that surface, then it is not truly decorating the
surface, but detracting from the object decorated.

At all times keep the principles of unity and subordination in mind when
producing modeling so that the design will be a related development to
the material and the surface used.

CEMENT TILES WITH A MODELED SURFACE are produced as follows: Take a
flat, smooth piece of clay or modeling wax, cut to the size of the tile
to be produced. Such a surface may be made by rolling clay or wax with a
rolling pin or other rounded surface. Having drawn the design to be
modeled on a piece of thin paper, place this over the clay and trace
lightly. This will produce a slight indication on the surface sufficient
to guide the modeling. If there are sections that are to be low, these
parts are outlined with an incision in the surface and scraped out to
the desired level.

Do this over the entire surface, bearing in mind that the edges of the
tile should generally have a border or other parts retained of the
original surface. Too much elimination on the tile edge will thin the
tile and weaken its construction and design.

Having scraped out all the low parts, then clay or wax may be added to
such parts that are to be higher than the first surface. With the
modeling tool shape the parts, finishing them so that there are no
overhanging edges.

When this is completed surround with the plaster bars and produce a mold
in plaster which in turn is oiled in the usual way and a cement tile
cast from it. Neat cement should be poured first, and after a few
minutes setting, a concrete mixture is poured in until the desired
thickness is secured. In this way a cement tile is secured, duplicating
in form the original clay or plaster hand-made modeled tile. The color
of the surface can be any color according to the color added to the neat
cement mixture.

DIFFERENT COLORS on different parts of the surface can be produced as
follows: Mix cement colors with equal parts of cement. Grind these
colors with the putty knife or pestle and place each color in a small
saucer or pan. Oil the surface of the mold with a brush, dabbing it on
in short strokes. The colors are next dripped from a brush onto their
right location. This layer of color should be about a quarter of an inch
thick and left to stand until firm on the surface. It is then covered
with a layer of concrete and smoothed off to a level.

TEA TILES OR LARGE TILES for inserts into garden furniture or for
architectural use can be strengthened by a reinforcement. A
reinforcement may be made from the ordinary window screening or any wire
fence mesh or so-called hardware cloths used in building construction.

This wire should be cut a little smaller than the tile and sunk into the
concrete layer while soft. It should be pressed down with the fingers
until the concrete closes over it. This will add a considerable strength
to the tile.

After the tile has set for several days, it is removed by inserting the
knife between the edges and carefully prying it apart, or steaming apart
by placing over a low flame for a few seconds. If part of the color
remains sticking to the plaster mold it is because there was not enough
oil on that particular spot. Therefore remember that a mold surface
should be well oiled before placing the color into it, and care being
taken that there is not so much oil that it settles in the hollows and
grooves.

The tile after drying thoroughly may be polished with wax and used.

FOR MODELING LARGER OBJECTS such as flower pots, urns or similar forms,
it is best to form some means of reinforcement to approximate fairly
closely the final form of the object. Close meshed wire can be used
successfully for this purpose. It should be tied and braced firmly so
that the concrete or cement weight will not destroy its shape. The
concrete mixture should be made with one part cement and two parts clean
sand.

TO HASTEN THE SETTING OF CEMENT add a very small quantity of common
washing soda to the water used in mixing the cement. This will cause the
cement to set up rapidly so that the work can be done more quickly.

AFTER THE MIXTURE HAS BEEN APPLIED over the wire reinforcement and
shaped and modeled until completed, it should be put in some covered
place or in a moist location for the first two or three days so that the
moisture in it will not evaporate.

TO HARDEN THE CEMENT OBJECT immerse it well in the water for four or
five days. If it stays longer in the water it will not hurt the object.
The water will harden or complete the action of hydration necessary to
make cement durable.

TO SECURE BISYMMETRIC SHAPES to forms or to secure true circular shapes,
a templet of sheet metal can be cut and rotated from a centrally located
axis. This is used while the mortar or concrete is in plastic condition
so that the templet will cut or model the right contour.

CARVED CEMENT is made possible by scraping or carving out the cement
when it is in the right condition. This condition can be determined by
scraping the cement to see whether it is hard enough to carve. If it is
too hard, it cannot be carved successfully. About sixteen to twenty
hours setting will produce about the right condition but this will vary
according to the mixture and climatic conditions, as temperature will be
an important thing to consider in all color cement work. Very hot
weather is not a good time to do color cement, the winter days or gray
cool days are best to work with cement for perfect hardening results.
Avoid freezing weather.

TO CARVE CEMENT, the tools may be of metal or nails shaped with cutting
points and the work done similarly to the carving of the sgraffito tile
described in the previous chapter. No adding or building of parts is
possible, the whole subject being a process of taking out parts and
shaping the parts that are left. Backgrounds and portions can be varied
in texture and different results will be secured with a little
experimenting.

DIFFERENT TEXTURES are possible in the carved tile. A glazed surface to
the carved tile is secured by carving on the upper side of the tile;
while the dull under surface, the side molded against the glass or under
surface, will be used if a dull surface for the carved tile is desired.

A GLAZED OR MAT FINISH BACKGROUND in the carved tile can be secured by
immersing the tile in water for a day or two for glazed finish or an
hour for a mat finish and then applying neat cement, plain or with color
as described in the chapter on Color Work for Tiles.

CARVING ON BOWLS AND VASES and other forms can be done, care being taken
that the carving does not go so deep as to weaken the surfaces. Motifs
or spaces can be carved out of cement bowls and vases and bits of
stained glass or mosaics, or color cement can be put into the spaces and
neat color cement used to bind the additions into the spaces.

SLIP-PAINTED PORTIONS MAY BE ADDED to the carved tile. After the tile is
carved and properly moistened in preparation for the cement to be added,
the color cement is mixed to a thin slip and a background pattern or
decorations can be added to the surfaces of the carved tile. The tile is
then placed in shallow water without permitting the water to reach the
surface of the tile, and permitted to remain for four to six days before
removing. It should then be placed in a cool location until completely
dried.

THE UNIT TILE or the small tiles made to be assembled in patterns, may
have modeled or carved cement surfaces combined with the units to
complete the pattern. For instance a number of tiles representing leaf
forms may be combined with others representing flower motifs. These may
be imbedded into a panel of cement or concrete, the units grouped in
some form of design growth, the stems and other related portions being
modeled in the cement, or carved in the surface after the cement is
somewhat hardened. The units can be in color or mat finish, the
background remaining in dull finish.

MODELED CEMENT TILES differ from the cement tile with a modeled surface.
In the first the modeling is done on wax or clay and the cement tile is
made by duplicating the effect by the use of plaster molds. The modeled
cement tile is a modeling of the cement by hand while it is still in a
plastic stage.

TO PREPARE CEMENT FOR MODELING, pour a concrete mixture into the mold so
as to allow for a second added layer of about one quarter inch of neat
cement. This last layer of neat cement is the part which is to be
modeled and can be made into a color by the addition of color to it.
This color should be added in the dry form to the dry cement, mulled or
ground well into the cement and then mixed with water until it becomes a
thick cement paste that will pour slowly onto the concrete mixture first
placed in the mold, until it covers the entire surface. A gentle jarring
of the mold will settle the color evenly and it should then be permitted
to stand until of a good modeling consistency.

A GOOD MODELING CONSISTENCY for cement is determined by testing it with
a tool or small pointed stick making a small incision or trying a small
section to see if the mixture holds its form. If the cement as laid up
on edge stays in position and does not have the tendency to fall or
settle, it is then ready to model, as it will hold its form when built
in relief.

PROMPT ACTION IS NECESSARY when the mixture is at this point and the
tool should be promptly used scraping or sketching the subject by
incised lines in the surface. Then parts of the cement are scraped from
the low portions and placed on the parts to be in higher relief until
the general rough forms are massed in. The smaller parts are then
detailed in and the different parts finished just as one would in
working with clay or modeling wax. If it is found that parts do not hold
up, it is because under sections of the cement have not dried
sufficiently and it will be necessary to wait until it hardens a little
more.

THE FINISHED RESULT may be complete with the strokes of the tool or the
modeling instrument showing over the entire surface.

If the technique is shown in this way, care should be taken that the
strokes are pleasing in direction and not carelessly left. As the tile
hardens it will be found that the surfaces or edges can be shaped, and
even when the surface is almost hard, it can be slightly indented or
carved to produce different textures and varying qualities.

GOOD MODELING TOOLS are those that are made from pear wood for sculptors
use. Metal modeling tools also can be used. Good home-made modeling
tools can be made from manicure sticks, pencils, dowel sticks or
ordinary small hardwood pieces shaped with a knife. These pieces should
be smoothed down very evenly with fine sandpaper and then rubbed with
beeswax or paraffin to avoid any rough surfaces. Rough surfaces will
cause the cement to stick to the tool. Experience will be a good guide
to the worker in color cement for determining the best shape to make the
modeling tool, as individual needs and ways of working will determine
the best form for each person.

[Illustration: Modeled and Carved Cement Tile Methods]




[Illustration]

CHAPTER 10

Color Cement
for Bowls and Vases

[Illustration]


THE COLOR FOR BOWLS AND VASES is mixed the same as for the tiles and it
will be found that the use of the muller to grind the color is necessary
to secure a good mixture. The color should be of the right consistency
for rotating inside of the molds, which can be best determined by a
trial. It will fall off the sides if too thin and if it is too heavy it
will fail to roll evenly.

TO PREPARE A VASE OR BOWL MOLD for color, the parts to come in contact
with the color should be oiled after they have been immersed in water.
The parts are then assembled and tied together. Corresponding marks or
figures can be placed on the molds so that there can be no mistake in
combining the correct sections. Such marks will avoid confusion,
particularly where the mold may be composed of a number of sections.
Molds for vases are not shellaced.

THE FIRST ROTATION is then made by taking a quantity of the color cement
or slip, mixed only with neat cement of thick quality, and pouring it
into the mouth of the mold into the bottom. A spoon may be used to place
the color if the mouth of the mold is large enough. The color is then
rotated by turning the mold gradually until the color covers all the
inside of the walls and the surplus is poured out into a pan. If the
color at first refuses to attach to the inside, a few slow revolutions
of the mold will generally overcome the trouble as the oil is causing
the separation and is overcome by a few turnings of the color.

THE SECOND ROTATION is accomplished in the same way that the first
rotation was but not until the first layer has fairly set. The surplus
from the first mixture may be used. It is placed or poured carefully in
and the rotating done and the surplus again poured out, excepting that
it is poured out from the opposite side so as to equalize the thickness
of the neck section of the vase or bowl.

A THIRD ROTATION may be necessary if the bowl is a large surface or if
the slip used has been very thin. After each rotation the mold with its
layer of inside color should be covered over with a damp cloth to
prevent too rapid drying of the color. The second and third mixtures
should be thinner than the first.

THE WALL MIXTURE is then rotated over the color stratas and is made of
one part of cement and two parts sand. This mixture is necessary to give
the bowl or vase strength and to make it waterproof. If neat cement
alone is used the vase will check and crack in time, particularly if
water is ever poured into it.

FOR SMALL VASES only one rotation of color is necessary and the second
and third may be of cement and sand with a fourth finishing layer in
color. This finish layer may be of any color desired within the range of
color cements or of neat gray cement only.

THE FINISH ROTATION is the layer that will appear as the inside lining.
This is made of color and neat cement and is rotated so as to cover the
cement and sand mixture. This mixture may be placed in the mold after
the vase or bowl has been removed from the mold, and this permits the
possibility of carrying the inside color over the edge of the mouth and
partly down the side as a decoration.

AFTER THE ROTATED COLORS HAVE DRIED, which generally takes from two to
five days, the mold is carefully opened and the vase removed. Flaws or
bubbles on the surface, if any, are corrected by scraping with a
moistened knife parts of the neck that are not to remain and others
filled in. The false neck or that portion that extends above the actual
vase is now carefully trimmed away, leaving only the actual bowl or
vase.

CARVING AND SCRAPING of the surface can be done while the surface is
slightly soft which is soon after the bowl or vase has been removed from
the mold. Glazed color may be placed into the spaces carved or scraped
from the surface if the surface is moistened well with water, then
adding neat cement over which the color is dripped following the
instructions as given for the tiles.

TO HARDEN THE OBJECT molded it is immersed in a bucket of water and left
for several days. If the surface has had color added to it after it has
come from the mold, it cannot be immersed in water as the color would be
floated off. It should have water poured on the inside and left to dry
in a cool place.

TONING WASHES can be made of thin color and brushed onto the surface
after the bowl has been well dampened. This will permeate the fine pores
of the cement as well as gather into the crevices particularly of a
carved or relief surface and if a contrasting color is used, it gives
pleasing effects.

GLAZING BOWLS AND VASES is much more difficult than coloring tiles. The
curved surface requires careful application. Prepare a quantity of
desired color to be applied. Then spread it out in a pan or dish (a
platter will do very well), revolve the bowl on the fingers so that the
surface comes in contact with the color. The color will adhere and the
bowl should be kept slowly revolving until the color sets. The bowl can
then be filled with water and left to dry. If the bowl is kept in one
position before the color is set, the moisture will cause it to run and
mar the surface. After the first color has set an additional color can
be dripped on at the top or other colors added into or onto this
surface. Different effects will be possible, depending upon how soon the
color is added to the first coating.

Dry color can be sprinkled onto the wet color and permitted to become
absorbed, giving an interesting effect. The color may be applied with a
brush or palette knife, and other ways of producing variations on the
surface may be produced by experimenting.

A VASE FORM WITH MAJOLICA SURFACE will need to have the surface turned
as it is worked upon. This can be done by revolving with the hand inside
of it, or if too small turned on a right angle support, padded so that
it will not injure the neck of the vase. The vase may have one end
supported on something to keep the worked part from coming in contact
with the surface. After a part has been filled in, it should be left to
set for a minute before turning the surface, otherwise the color will
drop out.

After the color is all in position, stand the vase upright and with a
funnel fill with water and let it harden for several days. The water
will supply the color surface with moisture preventing it from drying
too rapidly.

Any cement surface (tile or vase) before it is very hard can have motifs
scraped into it so that the design is a series of shallow openings in
the surface. The color cement can then be dripped into these openings
similar to majolica work and completed in the same way.

A vase with a plain surface can be made exceedingly attractive by adding
a few simple motifs well chosen and placed on the surface in this way.

FOR SLIP PAINTING tile or pottery surface, various colors to be used
should be mixed and ground on glass or marble with palette or putty
knife until thoroughly smooth. The colors should be placed in order on a
glass or enamel palette. Other hues may be produced by the mixture of
these colors or lightened by adding a white cement. A small brush is
used to apply the color. The surface to which they are being applied
should always be damp and the complete surface to be colored should be
done at one sitting. The tile or vase is then placed in water as
previously explained.

It is best that the color be thin rather than thick, and avoid going
over a surface a second time. A second stroke will destroy the lustre
which will otherwise remain on the surface.

A VASE OR BOWL FORM to be used for slip-painted color will have to set a
few minutes to prevent the color running when the bowl is turned for new
working surface. The bowl or vase is carefully filled with water and
left to set for several days, care being taken that no water drops onto
the slip painting. The object worked upon must be set in the shade to
dry, where nothing will come in contact with it.

[Illustration: Color Cement Vases]

[Illustration: Color Cement Vases]




[Illustration]

CHAPTER 11

Glass Mosaic Tiles

[Illustration]


FRAGMENTS OF STAINED GLASS can be secured from almost any stained glass
works without cost, as much of the odds and ends of glass are thrown
away. These fragments can be used in making Glass Mosaic Tiles, and used
correctly will produce charming and interesting results.

Mother-of-pearl or abalone flakes can also be used as small bits here
and there in designs and will be found to give an additional rich
effect.

Semi-precious stones or glass beads can be used in many ways such as
handles and tops or as rests for tea tiles, etc. The beads can be sunk
into the cement until the hole through the bead is concealed.

TO MAKE A GLASS MOSAIC TILE there are four steps as follows:

    1st. Making and tracing the design.
    2nd. Cutting the glass.
    3rd. Pouring the cement backing.
    4th. Releasing the tiles and finishing.

FIRST STEP: MAKING AND TRACING THE DESIGN. To make a design for glass
mosaic, plan a very simple design for the first problem. A few squares
joined by simple bars, composed in a simple pleasing arrangement will be
hard enough. Objects such as flowers, birds, trees, etc., must be
planned in simple forms. Remember that each piece is to be cut from
glass and intricate outlines, etc., must be abbreviated. Decide what
direction of line will tell the most in the shortest length. It will be
found that designing for glass mosaics or for stained glass is one of
the best influences for recording large masses, for producing the
maximum amount of subject with the minimum means of line.

After the design has been drawn out on paper it should be colored to
correspond with the stained glass fragments that have been secured.
Right here it may be well to state that the glass mosaic need not be
entirely covered with glass sections. Much of the background may be
cement and the colored portions (stained glass and mother-of-pearl) may
be only a certain portion or design running across the tile surface.

After the design has been colored, make a firm tracing from it and place
the tracing upside down on the table and a glass over this large enough
to cover it fully. The stained glass sections are assembled upon this
glass as they are cut.

SECOND STEP: CUTTING THE GLASS. A small glass cutter with a wheel can be
purchased at any hardware store and with a little practice glass can be
easily cut. Once the wheel is placed upon the glass it should be pressed
slightly so that it grips the surface. Then draw the cutter firmly
toward you without changing the angle of the handle and without turning
the handle to one side or another. A few taps with the tip of the handle
on the under side of the glass and a “bending and pulling apart” motion
of the glass with the fingers will cause it to come apart after the
cutting. Some glass cuts much easier than others and a good cut with the
cutter will cause it to come apart upon the slightest bending in the
fingers. Do not run the cutter wheel over a cut line in the glass a
second time, as it will injure the wheel. Practice cutting clear glass
as well as stained glass. The glass cutter should be placed with the
wheel in turpentine to preserve the cutting edge.

To cut the glass in the right shape use either of the following methods:
Trace the design upon stiff paper and number each section of the design
to correspond with numbers on the original sketch. Cut these sections
apart and use them as patterns to lay on the glass. The glass cutter is
then run around the edge of the pattern in cutting the glass. The second
method is to trace the sections to be cut directly onto the glass. If
carbon paper is used, the line will be definite enough to follow.

SMALL SECTIONS OF GLASS can be better separated after the glass cutter
has been used if small pliers or dull nippers are used to grip the
glass. Hold the largest piece of glass firmly between the fingers and
with the nippers grip the glass close up to the line of division and
with a quick downward turn of the nippers it will divide the glass along
the line produced by the cutter.

The sections of glass when all cut may be trimmed to truer forms by
using a corborundum stone or file.

AFTER THE GLASS HAS BEEN CUT, place a tracing upside down on the table
and a glass over the tracing. The tracing on the underside of the paper
should be visible through the glass, and of course is reverse in
position. Take each piece of glass and touch the right side with glue
and place it onto the glass over its location defined by the tracing.
Assemble all the glass in this way, all the pieces being glued face
downward onto the glass. Mother-of-pearl, metals, etc., can be assembled
the same way, and the fact that they are thinner than the glass need
make no difference as their surfaces all resting upon the glass will
result in their being all the same level on the completed tile.

THIRD STEP: POURING THE CEMENT. After the glass has been glued and left
remaining for several hours (to permit the glue to dry) the retaining
bars are placed on the glass, at the proper distance from the cut
sections and cement is then poured into and over the glass mosaics until
the required thickness of tile is secured. This mixture may be color
cement or the neat Portland cement, care being taken to pour it in
slowly from the center to avoid formation of bubbles.

FOURTH STEP: FINISHING THE TILE. When the tile has set for several days
it may be removed and an incised line made around the edge of each glass
mosaic. Place the tile in water to harden for several days. Remove and
let dry, then give the entire surface a gasoline wash of gray or other
color. A slight polishing of the surface will finish the tile. It will
be found that the moisture has softened the glue so that the whole tile
releases from the glass surface. The cement should be rubbed off of any
of the glass parts if it has encroached until the entire edges of the
glass mosaics are visible. This should be done before the tile is placed
in the water to harden.

[Illustration: Mosaic Tile Method]

[Illustration: Mosaic Tiles]

[Illustration: Mosaic Stone Tiles]




[Illustration]

CHAPTER 12

Flower Boxes and
Other Straight Forms

[Illustration]


THERE ARE THREE WAYS TO PRODUCE FLOWER BOXES in color cement and the
methods equally apply to other straight-sided objects that are to be
hollow or act as containers.

MOLDS MADE FOR STRAIGHT-SIDED OBJECTS have the advantage of permitting
the joints of the molds to come on the corners or junctures of the
straight sides; thereby making the entire elimination of any joints
remaining on the object (from where the molds come together) an easy
matter of removal.

ONE OF THE WAYS TO PROCEED IN THE MAKING OF A FLOWER BOX is as follows:
Take any ordinary good proportioned small wooden box, or block of wood
of the right shape, and place a thin layer of modeling wax over the
surface until it is smooth and evenly coated. Model the design desired
on the four sides, avoiding, as has been before cautioned, having
undercut or overhanging portions.

THE DESIGN MAY BE SECURED WITHOUT MODELING by taking the box and
covering the sides with cut cardboard designs, the cut sections
producing the motifs or the spaces between the cut and applied portions
being the motifs. In either case the cut sides of the portions applied
should slant so that the widest portion of any opening formed where two
applied pieces come together will be widest at the top. The reason for
this is to prevent locking of the plaster which will be poured over the
surfaces to produce the molds.

IF THE CARDBOARD IS USED FOR THE DESIGN after the glue is dry, the
entire surfaces of the portions to come in contact with the plaster is
given two coats of shellac, the second coat to be given after the first
coat is dry. The shellac should be permitted to dry well.

TO MAKE THE MOLDS the box with the design is turned upside-down and a
mold is made of the bottom first. This is done by surrounding the four
sides with wooden retaining walls so that the sides extend at least an
inch above the edges. Into the space formed by the four projecting
walls, plaster is poured and permitted to dry. This will result in a
slab of plaster to reproduce the bottom of the flower box in the final
cement casting. If legs or irregular portions are on the bottom, the
mold should include these portions.

As soon as this bottom section is hard, the keys are bored into it and
one of the sides is next molded. When molding the sides, turn the model
so that the plaster is poured onto the sides and not so that it is
poured alongside the surface. This is done by turning each side to be
molded so that it is horizontal or flat.

WHEN ALL THE MOLDS ARE MADE and dried they are ready for casting the
cement box. They should be placed in water until all parts have absorbed
moisture. Next they are oiled well and assembled. If more than one color
is to be used, the molds for those sides to have color should have the
color cement placed on the molds while the surfaces are flat. When this
color has set sufficiently to permit the sides to be placed upright,
without the color running, the sides should be assembled with the bottom
mold and the whole set tied together ready for the pouring of the
cement.

THE FIRST MIXTURE OF CEMENT should be a thick mixture, just as thick as
will run easily when the mold is rotated. The first mixture of cement
should be of neat cement and may have color mixed with it. It is poured
into the mold or placed in with a spoon, and the mold is rotated slowly
until the mixture has covered all the inside surfaces. The surplus, if
any remains, is poured out from one of the corners.

THE SECOND MIXTURE OF CEMENT should be poured in after the first layer
has set. This usually takes from an hour to half a day depending on
climatic conditions. The second mixture should be of sand and cement and
of a thinner mixture than the first. This is necessary as the first
layer will absorb moisture very rapidly from the second layer and
therefore it should be very thin.

THE LAST LAYER OR MIXTURE should have color in it also and is added in
the same manner as the second mixture, after the previous layer has set.
This is the finishing layer and the color should be arranged to be in
harmony with the outside color. A harmonious color will be one that is a
lighter value of the outside color or it may be color that is
complementary to the outside color.

THERE ARE TWO IMPORTANT THINGS TO REMEMBER in making pottery or boxes
where the molds are rotated. One is that the mold to be rotated should
not be shellaced. The reason for this is that the plaster molds must
absorb some water from the cement mixture to produce the thin lining or
inside coating. The second thing to remember is to pour the surplus
mixture in the second rotation from the side opposite that the first
surplus mixture was poured. As the lining is inclined to be thicker
where the pouring out occurs, using an opposite side for the second
pouring out will equalize the lining of color.

THE SECOND METHOD TO PRODUCE A FLOWER BOX is by spreading the color in
the mold with a knife, pressing it up against the sides with a palette
knife or small trowel. This is possible because the opening is large
enough to permit seeing the sides. Where the opening is small such as
that in a vase or jar with tapering sides it cannot be done this way and
the method of rotation must be relied upon.

WHEN SPREADING THE COLOR CEMENT or lining, the mold should be turned so
that as the mixture is placed and spread a flat surface is being worked
upon. This makes it easier to work and insures the cement adhering to
the mold. After the sides are fully covered, a thin mixture may be
poured into the bottom and this whole mixture (the bottom and walls)
permitted to harden.

IF DRAIN HOLES ARE NEEDED in the bottom of the flower box, two cylinders
of clay or modeling wax may be placed upright in the bottom of the mold.
These cylinders should be long enough to protrude above the bottom layer
of cement that is poured in, and after the cement layer has hardened,
they may be removed. This is preferable to endeavoring to drill the
holes out of the bottom after the box is removed from the mold which
might result in breaking the entire box.

AFTER THE BOX IS ENTIRELY DRY it may be given a gasoline color wash or
rubbed with a thin color cement wash and after the color has become
partly dry, the surplus rubbed off with a cloth. A wax rub given with a
soft cloth and floor wax afterwards will smoothen up the entire surface
producing a velvety surface.

THE THIRD WAY TO PRODUCE A BOX in color cement is by pouring, and the
method is as follows: When making the molds instead of making the parts
as usual, make a mold part for the top instead of the bottom, as the
pouring mold is made upside down.

When the four sides and top portion of mold are ready, they are
assembled and the metal inside mold is placed inside of the plaster
mold.

THE METAL INSIDE MOLD is a metal pattern which when folded together
represents the inside space of the box. Within this metal pattern or
box, strips of wood or plaster should be placed to keep the metal or tin
form in shape when the pouring of the cement commences. A good way to
secure a perfect fitting brace inside of the metal form is shown in the
working plate accompanying this chapter.

When this metal box with enclosed bars is placed in the right position
within the plaster mold, the cement mixture is then poured into the
spaces between the outside mold and the metal box until the space is
filled. Then the cement pouring is continued until the top of the metal
box is covered adding enough more to form the bottom. It will be thus
seen that the metal box must be planned low enough so as to permit of a
bottom space.

TO FINISH THE BOX, it is turned over after the cement has sufficiently
hardened and the plaster, or wooden bar, is removed. The sides of the
metal box are folded inward and the entire box removed. This will leave
the inside of the box free for the smoothing or scraping of faults or
filling in of bubble holes which can easily be accomplished before the
cement has entirely hardened. The outside portion of the plaster mold is
then removed and the flower box appears complete except for the surface
coloring or finishing as may be desired.

OTHER SQUARE-SIDED OBJECTS may be similarly treated, in some instances
the shapes or proportions requiring different handling. For instance, a
very long narrow box could not be easily produced by rotating and should
be made by the spreading or pouring method. Large surfaces or very long
surfaces should be reinforced by the placing of wire cloth in the walls
when the cement is poured in.

TAMPING OR PRESSING OF CEMENT is done by using cement and sand of a
consistency like wet sand. This is placed into the mold and pressed
firmly with a blunt stick, and a mallet can be used to tap these wooden
chisels so as to press the cement well into the apertures. This results
in a very firm surface and is particularly good for large boxes and
containers. Care should be taken that the molds are firmly fastened
together and the molds should be watched occasionally while the tamping
is taking place to see that they do not spread.

TILES, STAINED GLASS AND MOSAICS may be included in the decoration of
flower boxes. They should be glued firmly into position on the molds or
boards forming the mold for the box. After a day or two drying the molds
are assembled and the cement is poured in the usual way. The moisture
in the cement will be found to soften the glue so that on removal of the
molds the tiles, glass or mosaics will remain with the cement.

TO INCLUDE HANGING CHAINS, RINGS OR HOOKS in a cement box, the mold
should be arranged so as to accommodate the chain or metal through it.
The part or opening through which the metal passes is filled with clay
or wax to avoid the running out of the cement. The molds can be held up
from the table surface by a few blocks of wood or worked upon after
being placed on a trestle.

COVERS TO BOXES can be made in the same manner as boxes. A single flat
lid may have fewer molded parts but should have enough to permit easy
release of the cement.

[Illustration: Three Cement Box Methods]

[Illustration: The Making of a Cement Box]




[Illustration]

CHAPTER 13

Color Cement for the
Garden

[Illustration]


ARTISTIC GARDEN WORK can be enhanced by the use of color cement. While
ordinary cement and concrete construction has been much used, there are
still greater possibilities with the use of color cement. The use of
color in the open permits the use of bright colors, in key with the
flowers and foliage; and with color cement the formal or Italian garden
scheme or the informal or Japanese manner of garden arrangement is
delightfully possible. Pottery, garden furniture, fountains, walls,
chimneys, pools and walks are a few of the possibilities with color
cement.

LARGE GARDEN POTTERY is produced by the same principles as vases and
bowls, but as the proportions are much larger, the methods of working
are different.

Where a large jardinière is to be made, the form should first be built
up from clay and be formed upside down. Bricks or any other solid
material may be used for the main body of this form, and the clay built
over it as it will not then require so much clay. If a long nail or rod
or strong stick is placed in the center of this mass, it can serve the
purpose as an axis to a templet which will form the contour of the
jardinière when moved around in a circular direction. The metal must be
good and heavy and sometimes it is necessary to reinforce the templet
with wood.

After the clay form is built, cases are made in several sections from
the plaster the same as for small forms; and cement and concrete used in
large quantities after the same method as for small forms.

Large dish-pans, pails, etc., may be used for securing the inside form
for garden pottery. Oil the outside and bottom of the pail or pan used
and place it upside down on a table. If only a certain part of the
bottom is wanted, clay should be built up around it, so that only the
part wanted is exposed. With a strip of tin or linoleum for a moulding
case surround the inverted utensil and then pour the concrete around and
over it.

TO FORM THE GARDEN POTTERY more accurately on the outside, take it out
from the mold in two or three days and trim with a knife to the desired
form (in winter let the form stay in the mold four or five days). If
extensions or additions are wanted the vase, bowl or jardinière, should
be soaked in water for an hour or two and the form made from tin or
other material placed in position and the cement poured into the forms.

To secure smaller parts independent from the larger parts such as fishes
or cup forms for fountains, etc., the smaller part should be made
separate from the large form but a pin or extension should be arranged
so that it will fit into a groove on the larger form. This can then be
built together by the addition of a little cement.

GARDEN SEATS. The seat and ends can be made by using wooden forms which
can be released easily. Openings in the ends can be arranged by either
the use of wooden blocks or clay bars placed in the right location.
These blocks or bars should be taken out after the cement has dried
three or four days. A few nails in the blocks will make it easier to
lift them out.

Tiles made as previously explained can be inserted into the ends by
scraping an opening to accommodate them while the cement is still soft.
A little cement poured into the back and around the edge will fasten the
two together.

GARDEN FOUNTAINS. The bowl for fountains should be made independent of
the base or pedestal, but arranged so that the two groove together. This
can be planned by taking a clay impression or a plaster casting from the
surface. For instance, in making a bowl to rest on a pedestal, the
bottom of the bowl should have keys or projections planned. Now
supposing the bowl is finished, a pedestal should have depressions in it
to correspond with the projections on the bottom of the bowl. To secure
these the bowl itself or an equivalent surface in clay or plaster must
be made to combine with the other parts of the molding case when the
pedestal is made. These keys or grooves can be scraped out of the
pedestal top when soft if care is taken to secure the right location. By
resting the bowl upon the top a slight indentation will be made so that
the indentation can be increased to the proper depth to secure complete
“register” between the two parts.

When making plaster mold cases for large pieces, burlap, coarse cloth,
etc., should be dipped rapidly into the plaster and used to build up the
molding case. This produces greater strength in the plaster case.

A DESIGN UNIT used on large pottery or as a border to any large surface
can be planned and modeled in modeling wax. From this model a mold is
made in plaster. The clay can be pressed into this mold, lifted out and
placed upon the surface to receive it. A slight pressure and joining of
the edges will make it conform to the surface.

TO REINFORCE LARGE PIECES, wire, iron rods, wire mesh, or any such
material will serve the purpose. Any narrow junction point or narrow
part connecting two large parts should be reinforced.

PIPE CONNECTIONS FOR WATER, GAS, OR ELECTRIC WIRES must be planned for
often in garden furniture. A round wooden rod with a smooth surface and
oiled, having a larger diameter than the pipe to be used should be used
in the mold. This is then withdrawn to make room for the iron pipe. A
pipe can be used in place of the wooden rod, but of course it is then
held firmly in place, becoming part of the mass. All pipe should be
threaded for proper connections, and it is very advisable that you
confer with a plumber or electrician so that no mistakes will be made.

Straight-sided forms can be made from tiles as follows: Take four tiles,
soaked in water, afterwards imbed them on edge upside down in a layer of
clay. They should be placed vertical and at right angles to each other.
It is also better that the corners do not meet. Within these four tiles
a clay cube is placed leaving a certain space all around for the wall.
The cube should also be lower than the height of the tile to allow for
the bottom as the box is made upside down. With clay or cardboard stop
the corners and then pour in cement to the top of the tiles. Let harden
for a few days; then remove clay, smooth up corners, and set in water to
harden. Fern dishes, plant holders, etc., can be made in this way with
as many sides as desired. The accompanying chart further explains this
problem.

GARDEN WALKS can be made with large irregular cement slabs or stones
formed with concrete. This will produce all the beauty that comes from
natural flagstones and enables anyone to secure the effect even when
flagstones are not securable. Flat tile or irregular tile can be
produced as a finish surface to the concrete base underneath, the whole
being one solid mass, eliminating much of the breaking up and loosening
that comes when separate tiles are placed in a surface.

COLOR CEMENT FLAGSTONES are made as follows: First prepare a solid earth
under-foundation. To do this the surface is pressed with an iron roller
or tamped with an iron tamper or heavy wooden block. If the surface has
been previously walked upon for some time, it will be good and solid. On
this surface indicate by scraping with a stick or trowel the shapes of
the flagstones desired, and scrape the earth out of these areas to a
depth of one to two inches. This surface is then sprayed with water
until it remains damp and is ready for placing the concrete mixture.

THE CONCRETE PROPORTIONS should be one part cement to two parts or three
parts gravel. These parts are mixed well together dry and then water is
added while it is mixed again. The best way to add the water is to have
one person spray the water from a hose while a second person uses a hoe
to mix the wet portions and expose the dry sections.

A MIXING TRAY can be made from wood and should hold water fairly well as
it is important that there be no leaks while the mixing is proceeding as
the leaking water may carry off much of the cement. After a box has been
used several times, the cracks and crevices will become filled and the
mixing tray will become more waterproof.

WHEN THE CONCRETE IS THOROUGHLY MIXED a portion is then taken and placed
in one of the scraped areas and shaped with a trowel. The sides should
be left thick and preferably tapering slightly upward. This prevents
breaking edges later when in use such as occurs if the edges overhang.

THE TOP LAYER should be of colored cement and may be a very thin layer,
but in order to be durable it should be composed of one-half part of
cement and one-half part of gravel or sand. This is mixed with color
sufficiently to tint it, but the color should not be too great in
quantity for it will weaken the strength of the mixture.

THE COLORS FOR THE CEMENT FLAGSTONES is dry color and may be Venetian
red, yellow, ochre, Indian red, lamp black, burnt umber, or burnt
sienna. This mineral color should be mixed in well with the dry concrete
before water is added. Colors can be changed by mixing one color into
another. For instance, the red can be made less intense by the addition
of burnt umber or with the addition of a little lamp black. When adding
another color to a cement mixture to which water has been combined, do
not add the color dry but mix it with water first until it is a paste
before mixing it into the first mixture.

TO FINISH THE FLAGSTONES the color mixture is spread over the first
portion placed in the scraped area and spread with the trowel until it
covers all the surface of the first pouring. When this strata has
partly set, it can be surfaced with trowel marks or a few twigs or weeds
can be held in the hand and whipped over the cement surface, producing a
roughened texture. The stone should then be covered so as to protect it
from being walked upon and after the second day it should be sprayed
with water to help its hardening process while drying. Do not permit the
sun to prematurely dry the stones as the slower a cement dries the more
durable it will be.

BRIDGE WORK FOR THE GARDEN can be constructed with cement, and the use
of color combined with cement will enhance the project if used
reservedly and in good arrangement. Iron posts or supports can be used
as under parts of the bridge or a temporary support of wood can be used.
A wooden barrel has been used successfully to form the opening under a
cement garden bridge, the staves being knocked in to remove the barrel
after the bridge was completed.

Stones and tree limbs can be combined with the cement bridge toward
creating informal effects. The Japanese garden is delightfully arranged
with many surprise effects of stone work and pools, all of which can be
duplicated with cement.

NATURAL EFFECTS can be secured with the proper use of cement and the
possibilities are only limited by the time and interest of the worker.
It must be remembered that cement and concrete is a process of creating
stone and the stones can be formed in pleasing shapes and finishes and
colors according to the wish of the worker. There is great opportunity
for the worker with color cement to create garden ideas either for
pleasure or for remuneration and any enthusiastic worker can plan and
direct such work for neighboring needs or for those who are always
anxious for the different but pleasing garden creation.

A TILE EFFECT for walks or courts in regular pattern can be made by
pouring a color layer over a concrete solid layer. Previous to the
pouring thin strips of wood are placed so as to divide the space into
the tile shapes. These strips are afterwards taken out and the tile
edges scraped round, and the spaces where the wood was placed is then
filled with gray cement. This produces at considerable less expense the
same result as the inlaid tile surface.

THE DECORATED GARDEN TILE is where the color cement is poured onto the
square or rectangular concrete stones and while it is semi-moist other
color is dripped on or stroked into the surface with a brush, forming a
design motif. These motifs may appear at regular or irregular intervals
depending upon the pattern arrangement of the stones, and can be of
flowers, quaint birds or animals, preferably in abstract arrangements.

CHIMNEY STONES or flat stones for surfacing fireplaces or stone walls
can be made by pouring out the concrete mixture to which color has been
added. These should be poured onto a fairly hard ground surface which
has been previously watered. The stones can be of varying shapes and
sizes and with varying tints of colors. Gray cement alone will give a
good color to which may be added those made of Venetian red, Indian red,
and lamp black or yellow ochre.

When dry they should be immersed in water and then added to the brick
undersurface of the chimney or mantel by using a mortar made of a
mixture of lime and clean sand with water. To this add one-fourth to
one-sixth part Portland cement. The lime should be prepared previously
to combining with the sand by adding water to it, letting it remain for
a half day to two days in order that it will become slackened. Lime
gives adhesiveness to the plaster, and the brick surface to which the
stones are placed should be moistened with water before adding the
plaster layer into which the color cement stones are to be pressed.

Many other fascinating uses of color cement will develop into successful
applications in the hands of the craftsman who is interested in
beautifying the garden.

[Illustration: Helps in Cement Garden Pottery]

[Illustration: Application of Cement Tiles to Architectural Use]

[Illustration: Color Cement Flagstones Used for a Bridge, Garden
Pathway, and Entrance.]

[Illustration: Color Cement Used for Chimney Stones and Flagstones]




[Illustration]

CHAPTER 14

The Making
of Candlesticks and
Book Supports

[Illustration]


TO MAKE A CANDLESTICK WITH STRAIGHT SIDES the molds should be made in
sections, the divisions occurring where the corners come. This results
in the object coming from the mold with the mold lines where they can be
easily removed.

THE MOLD FOR A CIRCULAR CANDLESTICK or round base can be made in three
divisions similar to the making of a mold for a round vase. The mold
lines occurring on the surface can be obliterated as soon as the object
is removed from the mold.

A MOLD FOR A CANDLESTICK DIFFERS FROM A VASE MOLD in that it is made
upside down. As a candlestick is made solid instead of hollow like a
vase, the mold is filled from the bottom, the open part to hold the
candle being a projecting section into the space of the mold into which
the cement is poured.

TO MAKE THE MOLD SECTIONS the small section to reproduce the hole for
the candlestick is first made. The original model, made either from clay
or modeling wax, is placed upright and a strip of oiled cardboard or
metal fastened around the top and plaster poured into the candlestick
hole and up above the top to the level of the cardboard or metal which
should extend at least an inch above the top of the candlestick.

AFTER THE MOLD FOR THE TOP IS MADE each side should have a key space
bored into it and then the mold is placed back into the model, the
exposed portions of the plaster are oiled and the side section (round or
straight section) is next made, leaving the bottom open. The completed
parts of the mold are assembled and dried before using them for the
cement cast.

TO POUR THE CANDLESTICK CAST, assemble the molds after they have been
immersed in water and oiled and after tying them firmly together turn
them upside down and pour the cement into the opening. If a color is to
be used, the color should be poured in and the mold rotated until the
color covers the inner surface. Surplus color should be mixed and kept
to use later in completing the bottom. After the lining has set, a
mixture of sand and coarse cement should be poured into it and permitted
to settle. Jarring or tapping the mold will help the cement to settle.
If it settles, more cement should be poured in. After it has settled,
the color surplus similar to the surface lining is poured on to finish
the bottom.

WHEN THE MOLD IS OPENED the sides are opened first and the small mold
section forming the candlestick hole is carefully twisted out. If when
making this part of the mold, a T shape wire has been inserted it will
strengthen the mold.

TO MAKE THE BOOK SUPPORT, a model should first be designed and modeled
in clay or modeling wax. This design must be considered from its
practicability and the structural design therefore must be carefully
planned. The base on the book support should be heavy enough to
overbalance the upright portion so as to prevent the book support from
falling over. The upright portion may be of any simple shape and
enriched in any of the methods previously described for the decorating
of tiles.

A WOODEN BASE OR BACK FOR THE MODEL may be used on which to place the
modeling wax. A thin layer of the modeling wax may be placed over the
entire surface, and variations to the shape also can be made with the
modeling wax. A panel of plaster or a tile design can be incorporated
into the model instead of modeling. This method has been often used and
found to give good results.

GESSO OR RELIEFO MODELED PANELS CAN BE USED for book support designs by
attaching them to the surface of the model. If the gesso or reliefo is
first shellaced it will be found to be an excellent material with which
to produce modeled designs for color cement handicraft.


AFTER THE MODEL IS COMPLETED the first part of the mold to be made
should be the portion with the design. The triangular shape of the
design and base portion should be placed in position and supported so
that a single pouring of plaster will produce a mold of the design and
the upper surface of the base. Different shaped bases or irregular
shaped bases will require individual consideration when planning the
molds. The main thing to consider is that the parts of the molds must be
made so that the cast will release easily from the molds.


THE SIDES OF THE BOOK SUPPORT are next made, casting the sides while the
first piece cast is kept in close position over the model and drilling
keys in the sides to produce locking holds in the mold sections. The top
of the model is also cast, the bottom being the only portion not made,
as the book support like the candle is cast upside down.


PRECEDING THE POURING OF CEMENT the mold sections are soaked in water,
taken out and oiled, assembled and put closely together, and tied firmly
in position. The colored cement slip is then poured in, the mold is
rotated and the concrete or cement filler is poured in and permitted to
settle. The bottom or last layer is then poured on in the same color as
that used for the lining.


TO INSURE QUICK ASSEMBLY OF MOLD PARTS when working, the molds should be
marked with corresponding numbers so that the correct parts can be put
together rapidly.


TO FINISH THE BOOK SUPPORT it is removed from the mold, trimmed as
needed, placed in water to harden for several days, taken out and
permitted to dry slowly and then brushed well and waxed. A thin coating
of shellac may precede the wax. Two sets of molds for book supports will
enable two book supports to be made at one time and in this way the
color of both can be made to match each other.

[Illustration: Book Support and Candlestick Molds]




[Illustration]

CHAPTER 15

Color Cement for
Interior Decoration

[Illustration]


PRACTICAL USE FOR COLOR CEMENT inside the home is one of the greatest
possibilities with color cement as a handicraft. It enables the home
builder, the art student, or the busy housewife who has some idea of
decoration, to plan and execute durable tiles or panels for the floor,
walls or fireplaces, and to execute them with but little space and
equipment.

TO MAKE TILES FOR THE FLOOR, the tiles should be made in flat surfaces
and without relief parts that will project so as to become worn from
being walked upon. For floor surfaces pressed tiles are better than
poured tiles. Manufacturers of common cement tiles for architectural
purposes produce them in presses with several tons pressure. The
craftsman can secure very good pressed effects by using backing cement
that has very little moisture in it and tapping it in well, using a
block of wood and a mallet. The retaining sides of the mold should be of
wood or of some durable material that will withstand the pressure, and
hold together firmly.

POURED TILES FOR FLOOR USE made from a strong mixture of sand and cement
and with a small proportion of color will be found to be durable. One or
two coatings of shellac and a covering of floor wax will further
increase the durability of the wearing surface.

PLAIN TILES FOR FLOOR USE can be used with decorated tile and various
interesting patterns can be made (a few of which are shown) by
interspersing the tile in different arrangements. A glazed tile can be
made and used as a variation in combination with mat finish or dull
finish tiles. Several small tiles may be used to fill a space and
produce patterns in contrast to larger tiles. It will be found that with
a little design arrangement many interesting floor arrangements can be
made with tiles.

WHERE A LARGE NUMBER OF TILES ARE TO BE MADE several molds in
plaster-of-Paris should be made and a large quantity of color mixed at
once, and the first color placed in each tile consecutively and then
the next color, until all the colors have been placed in the six, eight,
ten or whatever number of molds is being made at the same operation.
After the color has set, the backing mixture of concrete is made and
poured into all the tiles.

A TEMPLET PATTERN MOLD for floor tiles is made by cutting templets from
either cardboard or linoleum with slightly tapering sides and gluing
these into position to produce the design. The templets should duplicate
the portions of a design and the design should be the first step in the
problem to be solved.

THE DESIGN FOR TEMPLET PATTERNS should be simple in form and division.
Geometric patterns and straight line forms are the best for use. Good
divisions of squares and rectangles and these divisions changed slightly
to floral or leaf shapes should be as far as any elaboration should go.

AFTER THE TEMPLET PATTERN IS CUT it is assembled and glued into position
on another card or glass surface and given two coats of shellac. It is
then placed within the retaining bars and a cast is made in plaster.
This cast in plaster is afterwards shellaced and becomes the mold for
casting the cement tile.

TO CAST THE CEMENT TILE the colors selected from parts of the design are
first mixed and placed into the mold. After the colors have been all
placed and permitted to harden, they are backed with a mixture of neat
cement and color which is next backed up with a concrete mixture and
then permitted to dry for three days. After being hardened in water for
several days after its removal from the mold, it is then ready to be
cemented in position for floor use.

THE BACK FINISH OF WALL TILES should have countersunk spaces to permit a
good grip or hold of the mortar that will be used to hold the tile in
position. These grip holds can be made by cutting four small rectangular
sections of cardboard and pressing them closely together into the back
of the tile after the last layer of cement has been poured. After the
cement has dried thoroughly and the tile is ready to be removed from its
mold, these cards can be easily removed.

TO USE WALL TILES they should always be immersed in water before the
mortar is applied. This prevents the moisture being absorbed out of the
mortar by a dry tile and assures better sticking of the tile to a
perpendicular surface.

TO MAKE GOOD MORTAR, building lime is placed in a mixing box or bucket
and water poured over it. Next day it can be taken and mixed with sand
until a rich, thick plaster results. To this add one-quarter or
one-eighth part of Portland cement to make it strong.

TO APPLY TILES TO AN UPRIGHT SURFACE, spray the brick or rock surface
with water. This can be done with a whisk broom or a large brush. A
cloth immersed into water and dabbed onto the surface will serve very
well. The tile which has been placed in a bucket of water to absorb
moisture is then covered with mortar on the reverse side. The surface of
the wall or fire mantel to receive the tile is also covered with a layer
of mortar and the tile is pressed into the mortar, causing the two
layers (the one on the tile and the one on the wall) to adhere to each
other.

TO CONNECT TILES ONTO AN OLD CEMENT SURFACE the following method should
be used: Clean the old cement surface well with a brush and water,
removing the dirt and dust. Sprinkle a thin layer of neat cement onto
this surface while the floor is still moist. Work this neat cement into
the surface well, pressing it and working it with a flat trowel. Onto
this add a layer of strong mixture cement into which the tiles are
pressed.

TO FINISH A TILE FLOOR the spaces between the tiles are filled with
cement; a small narrow cement trowel or strip of metal is passed over
the strip to smooth the cement in between the tiles. After the first day
the tiles and entire surface should be sprinkled with water to insure
good hardening of the cement.

THE SPACES BETWEEN THE TILES can vary in width, depending upon the size
of the tiles. A half-inch space of cement between six-inch tiles is a
good average. A tile surface either upright or flat looks better with a
liberal space between the tiles than where too close a connection is
attempted. The tiles also look more interesting if the cement in between
is left a little lower than the surface of the tile.

A color may be added to the cement used between the tiles, creating a
pleasing contrast in color and values. This color may be a thin coating
of color cement and need not be used throughout the entire cement
section.

TO SECURE A LEVEL TILE FLOOR with the color cement tiles, the under
layer of cement into which the tiles are placed should not be a wet
mixture of cement but a mixture of cement and sand that is a little more
moist than wet sand. The tiles are then pressed onto this layer, more of
the moist cement being pressed under the tiles until the tiles are level
with each other. To test the level surface a straight edged board is
placed straight edge downward along the surface. If it rocks on any part
of the surface, that part should be pressed downward or lowered by the
removal of some of the cement. If parts are too low, they will show a
light opening underneath the leveling edge and should be built up.

After the tiles are all level, the spaces between are filled with a soft
mixture of cement and finished smooth.

TILES FOR INSERTS IN WALL PANELS can be made in the same way as
described in the chapter on Tiles, excepting that they may be made
thinner to conform with the thickness of the wood or other surface to
which they will be added.

Where the wood or wall surface is grayed or toned with a paint wash or
tint, the tint can be carried over the tile insert which will help the
unity of the tile with the wall.

COLOR CEMENT TILES FOR FURNITURE INSERTS can be made in colors to
harmonize with the wood background. The surface finish given the wood,
whether wax or gray tone, can be also applied to the tile. The tiles may
be applied to boxes, chairbacks, flower stands so that they become the
bright spot of color motif to a design produced by the pattern of the
wood, or a carved or relief enrichment on the surface.

UNIT TILES FOR WALL SURFACES can be made and planned so that various
arrangements can be made by using the same motifs or elements. These
elements can be combined into a group that may be inserted into an over
mantel or into a wall or corridor space. Unit tiles admit of arranging a
vertical or a horizontal border or of combining both borders each
produced with the same motifs.

COLOR TILE BORDERS for plain cement floors will make an otherwise plain
floor a thing of beauty. A series of tiles for the border can be made
and special tiles for the corner arranged. The whole series can then be
set at the same time that the center plain gray or tinted portion of
cement is spread.

CEMENT FLOOR ABRASION CAN BE AVOIDED by dampening the cement as it
hardens and spraying water onto it regularly once or twice a day after
the first day for a period of five to seven days.

Abrasion or powdering of cement floors indoors often occurs because of
prematurely drying when constructed. Where walks out-of-doors are
benefited by the dew or moisture at night, inside floors do not receive
this moisture and often dry too rapidly.

To remedy the abrasion, or powdering of cement floors, wash the floor
thoroughly with clean water removing all dirt and particles with a
stiff scrub brush. After the surface has dried, apply a solution of one
part water-glass (sodium silicate) of 40 degrees Baumé and three to five
parts water, the water depending upon the absorbing quality of the
cement. This mixture is applied with a large brush and should be mixed
well and used within an hour. When this has dried mop the surface with
clean water and repeat the wash of water-glass three times, letting the
floor dry after each operation.

The silicate penetrates the pores, comes in contact with the other
alkalies in the concrete, forming an insoluble and very hard material,
preventing dusting and makes a better wearing floor.

[Illustration: Color Cement Tiles for Interior Decoration]

[Illustration: Color Cement Tiles for the Fireplace]

[Illustration: Tile Patterns for Wall or Floor]

[Illustration: The Unit Tile and Application]

[Illustration: Cement Tiles and Woodwork]




[Illustration]

CHAPTER 16

Surface Finishes

[Illustration]


COLOR CEMENT TILES ARE SURFACE FINISHED generally after they are dry. As
the tiles or pottery dry a lime or white powder dries on the surface and
the colors appear to become dull. To bring out the colors and remove
this powder, a soft cloth or soft brush is used to brush or dust off the
tile surface thoroughly.

AN OIL RUB can be given to the surface of the tile with raw linseed oil
on a soft cloth, and a brisk rubbing of the cloth will give a soft dull
polish. This should be done only on the cast and dull finish tiles and
not on the slip-painted or glazed surfaces.

A THIN SHELLAC COATING may be given a color cement tile or pottery as a
preliminary to a wax polish or a gasoline wash. White cement tiles or
pottery are very porous and a thin coating of clear white shellac will
prevent over absorption of surface coloring if the shellac is permitted
to dry thoroughly. Shellac should be applied after the surface is
thoroughly dried to prevent a sticky surface.

THE GASOLINE WASH is made by mixing white oil paint (flake white or zinc
white) with black paint (ivory black or lamp black) until a gray tone is
secured. This mixture should be made in a cup or bowl so that gasoline
can then be added until the paint is almost as thin as water. To this
mixture green or blue paint or other color should be added until the
right hue is secured. This is then brushed onto the tile surface and
brushed well into the crevices and countersunk sections as it is
important that the low sections be well filled. After the wash has dried
thoroughly, a soft cloth is used to rub off all the surplus. This will
leave the gasoline wash remaining only in the bottom or lower portions
giving a pleasing finish. After this has dried a wax rub may be placed
over it.

A WAX RUB is produced by taking either wax tan shoe polish or floor wax
and rubbing it onto the cement with a soft cloth. The cement should be
thoroughly dry before the wax is placed upon the surface. After a few
minutes a soft brush or woolen cloth should be used to polish the waxed
surface.

A wax rub can be applied over a gasoline wash, but only after the wash
has been given time to thoroughly dry. If the gasoline wash is not dry,
the wax will remove it in parts and destroy the effect produced by the
gasoline wash.

A COLOR CEMENT SURFACE FINISH is made by mixing a thin mixture of color
and cement which is then brushed onto the tile. The tile or surface to
be finished with cement should not be dry or be permitted to dry after
it has been removed from the mold. Previous to the application of the
cement color, the tile should be well moistened. After the color has
dried for several hours upon the surface, a cloth balled or gathered so
as to form a padded surface should be used to remove the color from the
high parts.

A SLIP SURFACE FINISH is where the tile or surface has been completed in
single or several colors and when hardened sufficiently in water, a thin
slip of color cement is placed over the entire surface and permitted to
settle into the hollows, leaving the higher portions to appear more
clearly through the colored slip. If the surface is a tile, it should
then be permitted to harden in shallow water placed in a tray with the
tile placed carefully into it so that the water does not reach the color
slip portions. If the object is a vase, it may be filled with water to
harden the outer surface properly. If the color has been used as a layer
on the inside, the bowl or vase should be placed in a pail and water
poured into the pail so that the object is surrounded with water. A
weight or board can be placed so as to prevent the object from floating
if it commences to do so.

COLOR MAY BE SPRAYED by mixing a thin mixture of color and cement and
spraying it onto the tile or pottery surface with a fixitive blower such
as may be obtained at artists’ supply stores and which is used by
artists for spraying a solution of shellac (termed fixitive) onto
charcoal or pencil drawings.

The color should be repeatedly stirred to keep it well mixed and if the
sprayer becomes clogged, it should be rinsed in water.

Too much color should not be sprayed at a time as it will fail to be
absorbed and run on the surface, resulting in streaks.

SPATTERED COLOR FOR SURFACES is secured by dipping a short-haired
bristle brush (the bristles are best when they are about one inch long)
into color cement and causing the color to spatter onto the surface by
rubbing a knife edge or straight edge of a stick along the brush. This
will cause the bristles to release suddenly, throwing pigment in the
opposite direction onto the object. A trial should first be made on
paper surface before the actual surface is used to avoid too much color,
such as would come from an overcharged brush or too vigorous rubbing.
The surface of the object should be moist or dampened well previous to
the spattering.

SPRINKLED DRY COLOR can be applied to surfaces. This will give a
pleasing effect in certain places where an antique or scattering of dry
color will enter into the nature of the design. The dry pigment can be
sprinkled onto the surface only where the surface has been covered with
a layer of other color that is still moist. This is necessary in order
that the dry color will absorb sufficient moisture from the other color
to amalgamate with the first color.

TEXTURE SURFACES are produced by working on the surfaces while they are
still moist or soft enough to admit the use of a tool or edge to press
or model the surface. Even when a surface might have become quite hard
it may be tooled or chipped and a cement wash or gasoline wash used to
give the tooled parts a unifying color.

REPEATED SURFACE COLORING may be done where the first coloring is not
satisfactory. It will be found that a more pleasing effect is often
produced by the second surface coloring being placed over the first.
Care should be taken that so much rubbing does not occur that it wears
parts of the tile or pottery surface that are soft.

SURFACE FINISHES PERMIT OF EXPERIMENTING and the craftsworker in color
cement must test out different combinations in order to achieve the most
desirable quality to respond to personal choice. A brilliant color wash
will often bring out the pattern in pleasing contrast, and at other
times it may be over absorbed and produce a mottled undesirable quality.
The condition of the molds and the amount of sand in the mixture all
influence the surface of the object and in turn influence the result of
the surface finishes.

[Illustration: A Surface Finish for Cement Handicraft]




[Illustration]

CHAPTER 17

Decorations in the
Open

[Illustration]


COLOR AS OUTER ARCHITECTURAL DECORATION was much used on the buildings
of Egypt and Assyria. The winged sphere in gold and amber against a
background of dark blue was commonly used on the outer walls of Egyptian
buildings and the processions of warriors and ancient kings decorated
the walls of the Assyrian cities.

THE GRECIANS USED COLOR ALSO and the beautiful Parthenon was decorated
with color and the restored model in the Metropolitan Museum of Art in
New York shows their use of color architecturally. The great Acropolis
was resplendent in bas-reliefs on the outer walls in color, gold and
silver.

THE ROMANS USED COLOR OUT OF DOORS on their buildings and the Etruscans
built in terra cotta coloring the outer walls with gorgeous decorations.
They recognized that architecture could be dignified and noble with
proper use of color decorations to enrich the building as a whole.

MURAL DECORATIONS IN THE OPEN were used by the Egyptians, examples of
which remain in our museums today, and so permanent were their colors
that the color schemes are apparent even at this day thousands of years
after their artists applied them.

Pompeians with their house-tops massed against their blue skies were
prompted to use orange-red largely in their decorations which were
lavishly applied in their gardens and other surroundings.

THE CHINESE USED COLORS SIMILAR TO THE POMPEIANS and their decorations
give brilliant notes to their buildings creating pleasing effects. The
Chinese medium has been one largely of lacquer which has been used over
their gold and painted color, producing transparent qualities making it
difficult to know where the actual surface begins.

COLOR ON OUTSIDE BUILDING SURFACES exists on many of the Italian
cathedrals and enriched color facades were used on many houses during
the Gothic period of which there remains examples at Heldesheim and
Nurenberg and other cities.

COLOR IN AMERICAN ARCHITECTURE IS POSSIBLE with the use of color cement
and with careful analysis of the colors used and methods of hardening,
the patient worker can accomplish much toward realizing this much sought
possibility.

THE FIRST STEP TOWARD SUCCESSFUL USE OF COLOR CEMENT in the open is to
realize that color used at all times must be protected from drying too
rapidly. If it does so, it will disintegrate and chalk away gradually.
The drying of color cement should be retarded as much as possible and
kept moist as long as the hardening process has not completed. It is
impossible, of course, to apply water to the face of a working surface
without destroying the glaze of the color, or the surface setting layer
once the surface commences to dry. Water applied at this time will cause
the surface to float in sections and ruin the entire surface. Therefore
the best way is to arrange for the water to be absorbed from the back
and this can be done easily where the panel or mural decoration is a
separate section to be applied to the building surface afterwards.

WHERE THE MURAL IS TO BE APPLIED TO THE WALL the surface must be first
roughened, next thoroughly dampened with water, then a layer of wet neat
cement placed upon it. The bed of cement or sand and cement is next
applied and the subject then applied onto this surface all at one
sitting. This is necessary to avoid any part drying, as it will be
impossible to dampen the surface for postponed work.

BETTER RESULT ON WALL DECORATION is possible where the color cement can
be applied before the wall mass has dried out. If the forms or board
walls can be removed before the cement has thoroughly set, whatever
color cement or cement underlayers necessary to the color surfacing are
placed upon it, will stand greater chances of remaining as a permanent
part of the whole structure.

TO PROCEED WITH A MURAL PANEL a pan of metal two inches larger each way
than the panel dimensions should be made from galvanized sheet metal.
This is to hold the mural cement slab onto which the subject is to be
painted.

THE CEMENT SLAB IS MADE by surrounding an oiled surface (wood or glass)
with wooden retaining walls similar to those used in making tiles. These
walls should be oiled and otherwise made proof against leakage of water
as it is necessary that all water in the cement be retained to perfect
the hardening. The mixture of sand and cement (one part cement and two
parts sand or gravel) is next poured into this space and permitted to
set for several hours. Over this surface a thin layer of neat cement may
be spread or dry neat cement sprinkled through a sieve and worked into
the moist surface with the flat side of a palette or other knife.

THE COLOR IS THEN APPLIED by mixing up the colors to be used into a
paste form and these can be applied with a brush or with a palette knife
shaping and forming the subject as if painting in ordinary colors.

If the color sinks in too rapidly and becomes lost, the under surface is
too wet and the painting should be delayed for several hours or until
the color applied lays upon the surface properly.

THE CEMENT SLAB IS TRANSFERRED TO THE METAL TRAY as soon as it is
removable from its surface. In fact, a good way is to move the wood or
glass under support with the cement slab upon it and place the whole
combination into the tray. If the sides are well set the retaining walls
can be removed, and as soon as the whole layer is set enough so as not
to be dissolved by water, water is poured in the tray until it comes
half-way up the side of the cement slab. This will prevent the whole
slab drying prematurely as the water will supply all that is needed. If
the water becomes absorbed more should be poured in. After it has
remained in the tray for a week, it may be withdrawn and permitted to
dry gradually. Wet cloths around it will prevent too rapid drying.

WHEN WORKING UPON THE SURFACE, the surface should be completed as the
space is covered, avoiding returning to work upon any part after it has
commenced to set. If the surface has formed a shell or thin layer and
reworking breaks this shell, the color in that section will not harden
properly. It requires direct, confident handling of the subject, and
reworking of the surface such as the painter in oils is accustomed to is
not possible with color cement.

A WHITE CEMENT SURFACE can be formed over a cement layer and when this
is nearly dry thin washes of color cement may be used onto the surface
similar to working with water color. The white cement will absorb the
color easily and parts of the design may be worked in opaque or solid
colors.

A DARK WORKING BACKGROUND may be used by mixing a layer of dark blue,
brown or green. A layer of black can also be used. Brilliant colors can
be brushed or dripped into this so that they sink and become a part of
the dark surface without being in relief. A slight shaking of the
surface or the tray will produce this amalgamation of colors.

WATER SHOULD NOT REACH THE COLOR SURFACE until after it is entirely dry.
To avoid water splashing onto the surface from the tray it is the best
policy not to pour water into the tray before the painting is completed
and only when the tray is to be left undisturbed.

TO CONNECT THE COLOR CEMENT MURAL with the building wall, the space to
receive it should be well moistened and covered with neat cement which
is well worked into the surface. The back of the cement mural is
similarly treated and the two cement surfaces are pressed together and
held in position by a brace or support until thoroughly dried. The space
or border edge around the panel should be filled in with cement at the
same time.

[Illustration: Decorations Painted with Color Cement]

[Illustration: Cement Color Painted Decorations Applied]




[Illustration]

CHAPTER 18

Tiles and Pottery
with Color Magnesite
Cement Work

[Illustration]


MAGNESITE CEMENT WORK is a mixture medium producing a hard marble-like
quality and does not contain any Portland cement, but is given in this
book in order to complete the possible plastic mediums for the worker
wishing to mold objects with permanent durable mediums.

MAGNESITE CEMENT IS A SUCCESSFUL INDUSTRIAL MATERIAL and is used by
builders in interior trimmings for floor tiles, in making of bath-room
surfaces and recently used in coating stairways and hallways, producing
a pleasing texture and durable surface. The material is fireproof,
cleanly and better than marble.

MAGNESITE IS A FORM OF LIMESTONE and is a carbonate of magnesia which is
produced by burning until all gases have been eliminated, leaving only
the oxide in the form of a pure white powder. It comes from Europe and
is found in Maryland, Massachusetts, New York, Vermont, California, and
Washington. It has been used extensively in Europe and when better known
will be used more generally in America.

MAGNESITE CEMENT AS AN ENAMEL has been used as a hardening surface on
concrete and cement surfaces and also on clay brick. The concrete or
cement or brick surfaces should be thoroughly moistened before the
magnesite mixture is placed upon it to avoid the moisture from the
magnesite being absorbed and improperly drying.

THE MATERIALS FOR PRODUCING MAGNESITE are calcined powdered magnesite,
chloride of magnesia, sulphate of magnesia, white sand, white talc and
fine sawdust.

The magnesite should be kept in a container, proof against exposure to
air and dampness, in order to preserve its full setting qualities.

Chloride of magnesia has the appearance of ice or alum and when exposed
has the tendency to dissolve but does not deteriorate. It is the
chemical which when united with the magnesite produces the binding or
cement qualities.

Sulphate of magnesia or epsom salts is an easily secured material and is
used in very small quantities in the formulae for producing magnesite
cement and which is given later in this chapter.

The white talc or soapstone used for giving a smooth and polished white
background is used as a filler.

White sand and the fine sawdust should be absolutely clean and are mixed
with the other ingredients to produce the composite mixture to produce
Magnesite Cement.

TO COMBINE THE INGREDIENTS proceed as follows:

FIRST MIXTURE. Two and one-half pounds of powdered magnesite and one
pound of white talc are mixed thoroughly with one quart of fine sawdust.
To this mineral, dry color similar to that used and described for color
cement should be added if a color tone is desired. About one-half as
much color should be used as there is magnesite. In other words, one
pound of color should be used with two and a half pounds of powdered
magnesite. A stone mortar should be used to grind the entire mixture
well together.

This first combination is a dry mixture and is then mixed with the
second mixture which is liquid.

SECOND MIXTURE. Take five parts by weight of chloride of magnesia
solution with a density of 25 tested with a Baumé hydrometer which is a
simple glass tube secured at any druggist for registering solutions. To
the chloride of magnesia solution add one-half part by weight of
sulphate of magnesia which is epsom salts and test with the hydrometer
until it records 15.

TO USE THE HYDROMETER, place water in a container and if the hydrometer
is placed in it, it will register “0” and when the chloride is placed in
it, and dissolves the hydrometer will commence registering the density
of the solution. When it records 25 no more chemical should be added.
More water should be added to correct the density if needed. The same
procedure is followed for registering the 15 for the epsom salts.

Chloride of magnesia will dissolve more rapidly if it is broken up, and
distilled water may be used if the usual available water contains lime,
iron or other injurious minerals. Some workers use rain water for many
purposes.

THE FINAL MIXTURE, or third step in the mixing, is to take the first dry
mixture and add enough of the second liquid combination to produce a
thick creamy mixture of the two. Strain this after it has been well
mixed.

TO PRODUCE TILES OR OTHER OBJECTS, THE MATERIAL is quickly poured into
the molds. A brush may be used for brushing the material well into the
edges and corners. A gentle jarring of the mold will remove the air
bubbles and the molds with the magnesite is permitted to dry for seven
to ten hours before the cast is removed from the mold.

FOR VARIOUS COLORS in the same design, the dry mixture can be mixed with
color and the liquid, or second mixture, added to it. This can be
applied to the mold in the same way as the color was used with cement,
and after it has set, can be backed with a general color of magnesite
cement or with plain magnesite mixture.

TO FINISH MAGNESITE let it remain drying for two or three days after
which it can be washed with slightly warmed water to remove the thin
scum on the surface. A thin coating of beeswax or floor wax well
polished will finish the article.

[Illustration: The Making of Magnesite Cement]

[Illustration: Magnesite Objects Cast from Molds]




[Illustration]

CHAPTER 19

Color Cement
Projects
for the Schoolroom

[Illustration]


CEMENT TILES simple in form may be made in any grade where tiles are
made in clay or the modeling waxes. Many times clay is used in making
tiles and the coloring is done with colored chalks or paints. These can
be but temporary in effect and are broken easily, being impractical for
use. The child’s interest will be much greater where he knows that with
cement the results will be durable as well as to know that he is working
with the same materials that the “grown-ups” use.

COMMENCING WITH SMALL TILES IS THE BEST PLAN. Have the class plan from
nature a rosette design for a two-inch tile. An excellent way to secure
interesting patterns is to fold a two-inch square paper into four folds
and cut a design in the four folds. Opening out these folds will often
reveal a very interesting design. When the student has completed the
design, it can be traced with a pencil onto a flat layer of modeling
wax, and a pencil, stick or nail used to cut away portions of the
design. The pattern designed may be the part taken out or the background
may be the part to be removed. In either case the part removed should be
scraped out about a quarter of an inch deep and the sides should not
slope in but rather outward. If the design is to be simply produced by
incised lines only (and charming results can be thus secured), the
stick, nail or instrument used should be sharpened so that it scrapes a
groove in the clay that remains widest at the surface. The design being
completed in the clay or wax, a few strips of thick cardboard or heavy
oiled paper is cut so as to project above the clay or wax tile. This
projection must equal the thickness of the mold to be made in
plaster-of-Paris. These strips may then be placed up against the tile so
as to surround it, and are to be retained in position with nails or pins
or heavy objects.

When the pupils have all reached this stage of the tile, the teacher
then may mix up the plaster and pour it into the molds, illustrating the
correct method for the students to afterwards follow.

AFTER THE PLASTER TILE IS RELEASED, it is brushed well with oil and
again surrounded with the strips of paper. Cement with any desired color
added to it is then poured in and after two or three days the completed
tile can be removed.

To secure color effects it is only necessary for the teacher to mix two
colors of cement sufficient for the student’s use. The student then
places a thin layer of the color on the plaster mold, keeping it within
a certain portion of the design. The second color is placed on the
spaces left, and after the color has set for a short time it is backed
with ordinary neat cement and the whole tile permitted to dry several
days.

TILES WITH THE DESIGN IN A RELIEF LINE can be made as follows: The
teacher should have previously made a number of plaster tiles with a
smooth surface. These can be easily made by flowing the plaster onto
glass or other hard, smooth surface, the plaster being retained between
two strips of wood 4 × 4 inches. Cutting these bars of plaster into
squares, one is given to each student. A simple design is made on paper
first and traced onto the plaster tile. A nail or hard pencil is then
used to incise the design in the plaster, after which it is brushed well
with oil and surrounded with cardboard strips and cement poured into it.
This will result in a tile with the design in relief. Within these
relief lines cement with color added to it may be placed and the tiles
placed in a tray of water with the water coming half-way up the side of
the tile. The tile will be hard enough to remove in five days.

SIMPLE ROUND PAPER WEIGHTS and tiles that are not square can be made by
the same method. A little ingenuity in arranging the retaining cardboard
strips around the plaster or wax model will solve the producing of
irregular forms.

FLOWER AND PLANT HOLDERS, FISH PONDS, AND BOOK SUPPORTS can be made by
using the tiles as the principle part. Take four tiles that have not
been permitted to dry and place them face against the inside wall of a
rough box form without the bottom, the size of the box to conform to the
tiles. Pour about an inch of cement into the bottom of the box to form a
bottom. When this has partly set, place strips of wood across the inside
covers to hold the cement which is then poured in so as to connect the
tiles where the corners meet. The cement should be poured also into the
outside corner spaces. After the complete form has dried for a day, pour
water inside and let it remain for three days or more. Release and trim
corners and inside as desired. A thin mixture of colored cement placed
inside and then poured out will give an inside lining, producing a
finished effect.

SAND BOX ANIMALS AND TOYS can be made in a very durable form by the use
of cement. The method to follow in class should be as follows: Have the
pupils outline an animal in simple form on paper. No intricate or small
details should be attempted in this outline and the feet or lower
portions of the animal must be planned so that it will stand up easily.

After the outline is made then secure thin strips of tin or other sheet
metal and have the pupils bend it with their fingers and with the use of
a ruler to conform to the outline. The metal should be about two inches
wide. The outline need not be made entirely of one piece of metal but
perhaps of several. When the outline is completed in metal, it should
conform fairly closely to the outline on the paper. This metal rim is
then pressed slightly into wax or clay, or it may be placed on glass or
on an oiled card. If clay is used, the eyes, wings, or other parts may
be incised in the clay within the metal rim. A one-inch layer of cement
is then poured in the metal rim, and after several days, the metal rim
is removed and the cement around it is evened where necessary and
colored if desired. By making the feet of birds or animals first,
combining wire legs with them, the body can then be cast, combining the
body and the legs through the wire connection.

MOSAIC CEMENT TILES can be easily produced as follows: Secure a number
of the small mosaic stone squares used by masons and tile setters for
inlaying floors. These come in many colors and different geometric
forms. Plan a four-inch tea tile arranging a design with the use of two
or three different colors of mosaics. When the arrangement or design is
decided upon, the mosaics should be glued face downward to a piece of
cardboard or glass. If glass is used, it should be brushed with oil
after the mosaics have been glued into position and before the cement is
poured. Where glass is used the design arrangement on paper can be
slipped underneath the glass to show the location and correct position
for gluing the mosaics onto the glass surface. The mosaic pattern is
then surrounded with retaining bars or slips of wood or surrounded with
metal and the cement poured over the mosaics until the right thickness
is secured. It is then left for several days to dry, after which it is
removed from the glass or the cardboard is peeled away from the cement
surface. The tile is then finished after being placed in water for a
week to harden. Glue a piece of soft leather or felt on the bottom when
the cement has thoroughly dried.

CEMENT BOXES AND BOOK SUPPORTS can be made by the use of mosaics, gluing
them onto sections of boards and then assembling the boards and tying
them so that they will hold the cement that is poured in to finish the
object. Where cement is removed from the mold before it has thoroughly
hardened, it can be shaped with a knife, and mosaic book supports or
boxes made in general form can be shaped easily this way.

VASES AND BOWLS as a problem for the schoolroom can be simplified if the
teacher produces previously several vase molds so that the pupils can
make their casts in individually selected colors, after which they can
scrape or slip paint the shapes as they are removed from the molds.

THE POSSIBILITIES OF COLOR CEMENT for schoolroom applied arts are many
and the interested teacher can arrange working equipment and methods of
presentation according to space and class size. One ingenious teacher
placed building paper on the floor of a schoolroom corner section,
covered several old tables with oil-cloth and secured excellent results
with her class room problems by permitting a small group of students to
work at a time on account of the limited equipment.

Another teacher had her students design and make tiles for a new school
building and today they are used as part of the enrichment of the
school. This correlation of the student’s work with every day utility is
one of the attractions of color cement for the school student, and
innumerable practical applications can be found for color cement. The
various problems for which directions have been given in the chapters of
this book can be arranged in more or less simple form for the various
school classes; and as a vocational subject it combines design with
construction in a sensible proportion.

[Illustration: Schoolroom Projects in Cement]

[Illustration: A Tile in Cement Made in the Grammar Grades]

[Illustration: A Tile Made in the Intermediate Grades]

[Illustration: Color Cement Tiles and Pottery Made by the Students of a
High School.]

[Illustration: Problems in Cement by Students of an Art School. 1 to 3
are Elementary Problems. 4 to 13 are Secondary Problems. 14 is a Palette
Knife Painting in Colored Cement. 15 is a Fish Bowl and Sun-Dial Made in
Cement by the Use of a Glue Mold.]




[Illustration]

CHAPTER 20

Designing for Tiles
and Pottery

[Illustration]


PRINCIPLES OF PATTERN DESIGN are important for the craftsman to be
familiar with, for the reason that it gives points with which to “check
up” drawings before they are applied, as well as to permit greater
facility in designing.

MANY DESIGN WELL without having learned the theories of design, having a
natural sense of good arrangement of details and spaces. However,
natural designers, as well as those who do not find it easy, will profit
by becoming well grounded in the design principles.

NATURAL FORMS afford excellent examples of principles, giving beauty in
line, form and color; and the more the designer refers to nature for
these ever occurring lines of grace and beauty, the greater will be his
development as a designer.

SUCH STUDY FROM NATURE should be intelligently pursued. To study nature
for design motifs does not mean that “photographic” arrangement or
life-like sprays should be applied onto surfaces. The most deplorable
forms applied to pottery or other handicrafts are those that have been
made with no thought of the surface influence upon the pattern designed.
The designer should refer to nature only as a reference from which
inspiration is received for motifs to be used. In every instance the
forms in nature should be interpreted into design and so transposed that
they beautify the surface irrespective to resemblance to the natural
source. Nature uses patterns in all her kingdoms correctly. The patterns
on petals and leaves, the pattern on bird plumage and animal skins, as
well as nature’s designs on minerals are all beautifully arranged to
conform to the contours of the surface. It would have been just as easy
for the Great Creator to produce forget-me-nots and violets in natural
splendor upon the leopard, but the ringed spots varying and converging
to the lithe, graceful lines of the surface without any appearance of
being in relief upon the skin are much more beautiful. Those who state
that “Nature cannot be improved upon” as an excuse for natural
representation in designing are overlooking nature’s real poetic
opportunities to the designer. No true artist or designer ever hopes to
actually represent nature. It is impossible. The best that can be done
is each individual artist’s interpretation of nature forms founded upon
governing principles. These principles have been tested by centuries of
scrutiny and all beautiful forms of historic ornament are governed by
principles which, as has been stated, originated in nature’s design
forms.

RADIATION, SYMMETRY, UNITY, SUBORDINATION, MEASURE, ETC., are all
principles of importance, but the three that are of great value to the
craftsman are Measure, Balance and Unity.

THESE THREE PRINCIPLES can be used to test the line, form and color of
the design before it is applied.

MEASURE is the principle that requires a consistent varying of areas,
line directions or colors. Measure creates interest. It does not mean
that large and small parts are to be designed without any further
consideration. There must be a right proportion of one to the other and
balanced as regards their location. Measure will control the contours or
forms of vases and motifs for if the widest part of the form comes above
or below center of the axis, it will be more interesting than if located
in the center. The working plate illustrates this.

BALANCE is the principle which creates harmony by contrasting measures.
If we have a heavy spot on one side of a design, the eye requires
satisfaction by seeing another spot or several parts equal in weight to
the large spot on the opposite side of the design. Balance is also
secured by locating a unit or design spot in the proper location of a
space, without necessarily having a second opposite spot. Nevertheless,
it is balance in relation to its background. Balance may be secured by
Symmetry, making parts like-sided or balance may be secured by equal
amounts of form on two sides of an axis, even though not symmetrically
placed. (See working plate.)

Balance in color requires that if a color is used in a single spot that
its location be pleasingly balanced within the space decorated. Where a
color is to be used in several places in the design, these different
spots should balance each other.

UNITY is the principle which brings harmony into design by similarity of
parts, by keeping lines of a design parallel to the space outline within
which they are designed. Again the main lines of a design if radiating
from a point or axis within or without the design space produces unity.
Unity is produced by harmonious values and by harmonious color.

A DESIGN WITHOUT UNITY may be one where the parts are too varied in
form, where they do not pertain or group with each other, but appear
“explosive.” Different finishes to the motifs in a design destroy unity.
Avoid mixing naturalistic or conventional and geometrical motifs in the
same design, and using lines or forms which are not pleasing in
direction, or harmonious with the space in which they are placed.

UNITY requires that all parts of a design be of similar expression. To
have one part of a design based upon a poppy or bird with a section
drawn naturalistic and another part conventionalized and possibly a
third section in geometric arrangement is to produce disorder or
dissimilarity, and yet such fault is apparent in a large proportion of
designs.

ALL DESIGN FORMS CAN BE DIVIDED INTO FOUR DIVISIONS and these divisions
can be defined as Naturalistic, Conventional, Geometric, and Abstract.
If any design motif for a tile or any application is started in a
Naturalistic manner, then all parts should be expressed in the same
manner.

THE NATURALISTIC DIVISION OF DESIGN is where natural forms and growth
arrangements are planned or designed within a given or arbitrary space.
The decorative arrangement comes from carefully planning the subject so
that it composes in a pleasing way within the space. The Japanese
designs are good examples of this kind of decoration. It will be found
that careful attention is given to the background spaces as well as to
the parts of the subject being drawn. Strong outlines, double outlines
and individual techniques or renderings further increase the decorative
quality of a naturalistic design.

THE CONVENTIONAL DIVISION OF DESIGN is where a typical form from a
nature growth is taken and repeated in regular repetition, or a general
shape formed from a plant form and used to interpret the subject. For
instance, a flower with several petals will have each petal different in
contour, but in conventional design, one shape is chosen and this shape
is repeated. While no two leaves are alike on the plant, one or two
conventionalized shapes are determined and these shapes are then used
throughout the design. The veins and stems of the flowers may be
elaborated or the leaves may have their centers designed or “inhabited”
so that added interest may be created in the subject.

THE GEOMETRICAL DIVISION OF DESIGN is when the subject is designed
entirely with triangular, rectangular, square, oval, elliptical, or
circular shapes, or where the outlines follow straight lines which may
go at right angles to each other or in oblique directions. Such straight
line designs are technically required for rug or textile designs and due
to the ruggedness and strength or interest achieved through a straight
line rendering are often adapted for decorating many other forms of
applied art.

THE ABSTRACT DIVISION OF DESIGN is represented by that form of design
which may have little direct representation of the natural forms, but
has been developed from it. We find that the wave border of the
Egyptians and the Greek fret are abstract designs of the water. The
Peruvian Inca, the Aztec and North American Indian used abstract designs
of the bird and other nature forms in their textiles and pottery. The
abstract design requires a careful arrangement of line and form spaces,
depending as it does on good design for interest rather than its
identity to nature forms.

LINE UNITY is that principle which appeals to the eye by the relation of
lines in the design to the space decorated. Curved lines for curved
forms and straight lines in the designs decorating straight lined forms
will do much toward making all parts consistent. A line not too curved
and with a blending of straight lines with the curved direction produces
a line of character and strength for design rendering.

A TEST OF GOOD DESIGN is to see if the main lines or “frame lines” are
pleasing in direction, decorating the space, whether any more details
are added or not. No amount of filling in and adding of motifs will
perfect an imperfect beginning.

BLOCKING IN of general forms is considered essential in freehand drawing
and it cannot be discarded in designing. First plan the main lines of
growth of the design. Then block in the masses or motifs to be used. The
details and connections as well as the technique of the design will then
be a simple matter to solve.

THE GREATEST ENJOYMENT to the craftsman in any line of endeavor lies
only through working out of Good Design.

WHEN MODELING FOR COLOR CEMENT HANDICRAFT or for any applied art it will
be found that three forms that are least modeled will be most pleasing
in the years of usage. High relief is not refined or deservable in
applied modeling. Sculptors everywhere are studying and returning to the
chaste, quiet forms of flat bas-reliefs of which we find excellent
examples among the early work of the Egyptians, Byzantines, the early
Indian and Chinese carvings, as well as the work of the Aztecs and Maya
Indians of early America. A few examples of these types are shown and
workers in color cement will find ultimately that they have chosen a
good influence if they will work their projects in color cement
handicraft in this manner.

High projecting parts and naturalistic representation of flower or
foliage masses are neither pleasing nor artistic and a visit by anyone
to the good museums will fail to find any such productions from the art
ages of the past recorded as good examples of the era.

Keep all parts applied to the curved or flat surface of the bowl, vase,
box or tile so that it appears to have been always a part of it rather
than an afterthought and detachable in relation.

[Illustration: Helpful Design Principles for Color Cement Work]

[Illustration: Outline Patterns for Color Cement Handicraft]

[Illustration: Tone Patterns for Color Cement Handicraft]

[Illustration: Egyptian, Roman and Aztec Relief Decorations]


Typographical errors corrected by the etext transcriber:

tested with a Beaume=> tested with a Baumé {pg 175}

40 degrees Baume=> 40 degrees Baumé {pg 153}