Produced by Victoria Woosley, Don Kretz, Juliet Sutherland and the
PG Distributed Proofreaders Team





[Illustration]




SCIENTIFIC AMERICAN SUPPLEMENT NO. 821




NEW YORK, September 26, 1891

Scientific American Supplement. Vol. XXXII, No. 821.

Scientific American established 1845

Scientific American Supplement, $5 a year.

Scientific American and Supplement, $7 a year.

       *       *       *       *       *




TABLE OF CONTENTS.


I.    Architectural.--The New Labor Exchange in Paris.--With
      views of the interior and exterior of the building

II.   Electrical.--The Construction and Maintenance of Underground
      Circuits.--By S.B. FOWLER.--A comprehensive article,
      discussing at length the various devices for protecting underground
      circuits, methods _of_ inserting the cables, etc.

III.  Engineering.--Railroads to the Clouds.--Sketches of a number
      of mountain railroads

IV.   Marine Engineering.--The French Armored Turret Ship
      the Marceau.--1 engraving.--A full description of the vessel, giving
      dimensions and cost

      A Review of Marine Engineering during the Past Decade.--A
      paper read before the Institution of Mechanical Engineers by Mr.
      Alfred Blechynben, of Barrow-in-Furness.--This paper, which
      is continued from Supplement No. 820, treats on steam pipes,
      feed water heating, twin screws, etc.

V.    Miscellaneous.--The Little House.--An article giving various
      hints about the arrangement and management of small
      dwellings, with special view to the best sanitary arrangements

      Stilt Walking.--A sketch, with engraving, of Sylvain Dornon,
      the stilt walker of Landes

      Remains of a Roman Villa in England

      Gum Arabic and its Modern Substitutes.--A continuation of a
      paper by Dr. S. Rideal and W.E. Youle.--With 26 tables

      A New Method of Extinguishing Fires.--Invented by George
      Dickson and David A. Jones, of Toronto, Canada.--Apparatus designed
      to utilize a mixture of water and liquefied carbonic acid

VI.   Medicine and Hygiene.--The Hygienic Treatment of
      Obesity.--By Dr. Paul Chebon.--Methods of eating, drinking,
      and exercising for the purpose of reducing fat.--An extended
      article, giving valuable information to people troubled with too
      much flesh

VII.  Photography.--Spectroscopic Determination of the Sensitiveness
      of Dry Plates.--A full description of the new plan of
      Mr. G.F. WILLIAMS, for determining the sensitiveness of dry
      plates by the use of a small direct vision pocket spectroscope

VIII. Physics.--A Physical Laboratory Indicator.--By J.W.
      MOORE, of Lafayette College.--1 engraving.--This is a modification
      of the old peg board adapted to use in the laboratory.--It indicates
      the names of the members of the class, contains a full
      list of the experiments to be performed, refers the student
      to the book and page where information in reference to experiments
      or apparatus may be found, it shows what experiments
      are to be performed by each student at a given time, etc.

      Cailletet's Cryogen.--A description, with one engraving, of Mr.
      Cailletet's new apparatus for producing temperatures from 70
      degrees to 80 degrees C., below zero, through the expansion of
      liquid carbonic acid

IX.   Technology.--The Manufacture of Roll Tar Paper.--An extended
      article containing a historical sketch and full information
      as to the materials used and the methods of manufacture

      Smokeless Gunpowder.--By Hudson Maxim.--A comprehensive
      article on the manufacture and use of smokeless gunpowder,
      giving a sketch of its history, and describing the methods of
      manufacture and its characteristics

      Method of Producing Alcohol.--A description of an improved
      process for making alcohol.--Invented by Mr. Alfred Springer,
      of Cincinnati, Ohio

       *       *       *       *       *





[Illustration: INTERIOR OF THE NEW LABOR EXCHANGE, PARIS.]

[Illustration: NEW LABOR EXCHANGE, PARIS.]

THE NEW LABOR EXCHANGE, PARIS.


The new Labor Exchange is soon to be inaugurated. We give herewith a
view of the entrance facade of the meeting hall. The buildings, which
are the work of Mr Bouvard, architect, of the city of Paris, are
comprised within the block of houses whose sharp angle forms upon
Place de la Republique, the intersection of Boulevard Magenta and
Bondy street. One of the entrances of the Exchange is on a level with
this street. The three others are on Chateau d'Eau street, where the
facade of the edifice extends for a length of one hundred feet. From
the facade and above the balcony that projects from the first story,
stand out in bold relief three heads surrounded by foliage and fruit
that dominate the three entrance doors. These sculptures represent the
Republic between Labor and Peace. The windows of the upper stories are
set within nine rows of columns, from between the capitals of which
stand out the names of the manufacturers, inventors, and statesmen
that have sprung from the laboring classes. Upon the same line, at the
two extremities of the facade, two modillions, traversed through their
center by palms, bear the devices "Labor" and "Peace." Above, there is
a dial surmounted by a shield bearing the device of the city of Paris.

The central door of the ground floor opens upon a large vestibule,
around which are arranged symmetrically the post, telegraph,
telephone, and intelligence offices, etc. Beyond the vestibule there
is a gallery that leads to the central court, upon the site of which
has been erected the grand assembly hall. This latter, which measures
20 meters in length, 22 in width, and 6 in height, is lighted by a
glazed ceiling, and contains ten rows of benches. These latter contain
900 seats, arranged in the form of circular steps, radiating around
the president's platform, which is one meter in height. A special
combination will permit of increasing the number of seats reserved for
the labor associations on occasions of grand reunions to 1,200. The
oak doors forming the lateral bays of the hall will open upon the two
large assembly rooms and the three waiting rooms constructed around
the faces of the large hall. In the assembly rooms forming one with
the central hall will take place the deliberations of the syndic
chambers. The walls of the hall will, ere long, receive decorative
paintings.--_L'Illustration._

       *       *       *       *       *




MANUFACTURE OF ROLL TAR PAPER.


Roofing paper was first used in Scandinavia early as the last century,
the invention being accredited to Faxa, an official of the Swedish
Admiralty. The first tar and gravel roofs in Sweden were very
defective. The impregnation of the paper with a water-proofing liquid
had not been thought of, and the roofs were constructed by laying over
the rafters a boarding, upon which the unsaturated paper, the sides of
which lapped over the other, was fastened with short tacks. The
surface of the paper was next coated with heated pine tar to make it
waterproof. The thin layer of tar was soon destroyed by the weather,
so that the paper, swelled by the absorption of rain water, lost its
cohesiveness and was soon destroyed by the elements. This imperfect
method of roof covering found no great favor and was but seldom
employed.

In Germany the architect Gilly was first to become interested in tar
paper roofing, and recommended it in his architecture for the country.
Nevertheless the new style of roof covering was but little employed,
and was finally abandoned during the first year of the 19th century.
It was revived again in 1840, when people began to take a renewed
interest in tar paper roofs, the method of manufacturing an
impermeable paper being already so far perfected that the squares of
paper were dipped in tar until thoroughly saturated. The roof
constructed of these waterproof paper sheets proved itself to be a
durable covering, being unimpenetrable to atmospheric precipitations,
and soon several factories commenced manufacturing the paper. The
product was improved continually and its method of manufacture
perfected. The good qualities of tar paper roofs being recognized by
the public, they were gradually adopted. The costly pine tar was soon
replaced by the cheaper coal tar. Square sheets of paper were made at
first; they were dipped sufficiently long in ordinary heated coal tar,
until perfectly saturated. The excess of tar was then permitted to
drip off, and the sheets were dried in the air. The improvement of
passing them through rollers to get rid of the surplus tar was
reserved for a future time, when an enterprising manufacturer
commenced to make endless tar paper in place of sheets. Special
apparatus were constructed to impregnate these rolls with tar; they
were imperfect at first, but gradually improved to a high degree. Much
progress was also made in the construction of the roofs, and several
methods of covering were devised. The defects caused by the old method
of nailing the tar paper direct upon the roof boarding were corrected;
the consequence of this method was that the paper was apt to tear,
caused by the unequal expansion of the roofing boards and paper, and
this soon led to the idea of making the latter independent of the
former by nailing the sides of the paper upon strips running parallel
with the gable. The use of endless tar paper proved to be an essential
advantage, because the number of seams as well as places where it had
to be nailed to the roof boarding was largely decreased. The
manufacture of tar paper has remained at about the same stage and no
essential improvements have been made up to the present. As partial
improvement may be mentioned the preparation of tar, especially since
the introduction of the tar distillery, and the manufacture of special
roof lacquers, which have been used for coating in place of the coal
tar. As an essential progress in the tar paper roofing may be
mentioned the invention of the double tar paper roof, and the wood
cement roof, which is regarded as an offshoot.

The tar paper industry has, within the last forty years, assumed great
dimensions, and the preferences for this roofing are gaining ground
daily. In view of the small weight of the covering material, the wood
construction of the roof can be much lighter, and the building is
therefore less strained by the weight of the roof than one with the
other kind, so that the outer walls need not be as heavy. Considering
the price, the paper roof is not only cheaper than other fireproof
roofs, but its light weight makes it possible for the whole building
to be constructed lighter and cheaper. The durability of the tar paper
roof is satisfactory, if carefully made of good material; the double
tar paper roof, the gravel double roof, and the wood cement roof are
distinguished by their great durability.

These roofs may be used for all kinds of buildings, and not only are
factories, storehouses, and country buildings covered with it, but
also many dwellings. The most stylish residences and villas are at
present being inclosed with the more durable kinds; the double roof,
the gravel double roof, and the wood cement roof. For factory
buildings, which are constantly shaken by the vibrations of the
machinery, the tar paper roof is preferable to any other.

In order to ascertain to what degree tar paper roofs would resist
fire, experiments were instituted at the instigation of some of the
larger manufacturers of roofing paper, in the presence of experts,
architects, and others, embracing the most severe tests, and it was
fully proved that the tar paper roof is as fireproof as any other.
These experiments were made in two different ways; first, the
readiness of ignition of the tar paper roof by a spark or flame from
the outside was considered, and, second, it was tested in how far it
would resist a fire in the interior of the building. In the former
case, it was ascertained that a bright, intense fire could be kept
burning upon the roof for some time, without igniting the woodwork of
the roof, but heat from above caused some of the more volatile
constituents of the tar to be expelled, whereby small flames appeared
upon the surface within the limits of the fire; the roofing paper was
not completely destroyed. There always remained a cohesive substance,
although it was charred and friable, which by reason of its bad
conductivity of heat protected the roof boarding to such an extent
that it was "browned" only by the developed tar vapors. A fire was
next started within a building covered with a tar paper roof; the
flame touched the roof boarding, which partly commenced to char and
smoulder, but the bright burning of the wood was prevented by the
air-tight condition of the roof; the fire gases could not escape from
the building. The smoke collecting under the roof prevented the
entrance of fresh air, in consequence of which the want of oxygen
smothered the fire. The roofing paper remained unchanged. By making
openings in the sides of the building so that the fire gases could
escape, the wood part of the roof was consumed, but the roofing paper
itself was only charred and did not burn. After removing the fire in
contact with the paper, this ceased burning at once and evinced no
disposition whatever to spread. In large conflagrations, also, the tar
paper roofs behaved in identically a similar manner. Many instances
have occurred where the tar paper roof prevented the fire from
spreading inside the building, and developing with sufficient
intensity to work injury.

As it is of interest to the roofer to know the manner of making the
material he uses, we give in the following a short description of the
manufacture of roofing paper. At first, when square sheets were used
exclusively, the raw paper consisted of ordinary dipped or formed
sheets. The materials used in its manufacture were common woolen rags
and other material. In order to prepare the pulp from the rags it is
necessary to cut them so small that the fabric is entirely dissolved
and converted into short fibers. The rags are for this purpose first
cut into pieces, which are again reduced by special machines. The rags
are cut in a rag cutting machine, which was formerly constructed
similar to a feed cutter; later on, more complicated machines of
various constructions were employed. It is not our task to describe
the various kinds, but we remain content with the general remark that
they are all based on the principles of causing revolving knives to
operate upon the rags. The careful cleansing of the cut rags,
necessary for the manufacture of paper, is not required for roofing
paper. It is sufficient to rinse away the sand and other solid
extraneous matter. The further reduction of the cut rags was formerly
performed in a stamp mill, which is no longer employed, the pulp mill
or rag engine being universally used.

The construction of this engine may be described as follows: A box or
trough of wood, iron, or stone is by a partition divided into two
parts which are connected at their ends. At one side upon the bottom
of the box lies an oakwood block, called the back fall. In a hollow of
this back fall is sunk the so-called plate, furnished with a number of
sharp steel cutters or knives, lying alongside of each other. A roller
of solid oakwood, the circumference of which is also furnished with
sharp steel cutters or knives, is fastened upon a shaft and revolves
within the hollow. The journal bearings of the shaft are let into and
fastened in movable wooden carriers. The carriers of the bearings may
be raised and lowered by turning suitable thumbscrews, whereby the
distance between the roller and the back fall is increased or
decreased. The whole is above covered with a dome, the so-called case,
to prevent the throwing out of the mass under the operation of
grinding. The roller is revolved with a velocity of from 100 to 150
revolutions per minute, whereby the rags are sucked in between the
roller and the back fall and cut and torn between the knives. At the
beginning of the operation, the distance between the roller and the
back fall is made as great as possible, the intention being less to
cut the rags than to wash them thoroughly. The dirty water is then
drawn off and replaced by clean, and the space of the grinding
apparatus is lessened gradually, so as to cut the rags between the
knives. The mass is constantly kept in motion and each piece of rag
passes repeatedly between the knives. The case protects the mass from
being thrown out by the centrifugal force. The work of beating the
rags is ended in a few hours, and the ensuing thin paste is drawn off
into the pulp chest, this being a square box lined with lead.

From the pulp chest it passes to the form of the paper machine. This
form consists of an endless fine web of brass wire, which revolves
around rollers. The upper part of this form rests upon a number of
hollow copper rollers, whereby a level place is formed. The form
revolves uniformly around the two end rollers, and has at the same
time a vibratory motion, by which the pulp running upon the form is
spread out uniformly and conducted along, more flowing on as the
latter progresses. The water escapes rapidly through the close wire
web. In order to limit the form on the sides two endless leather
straps revolve around the rollers on each side, which touch with their
lower parts the form on both sides and confine the fluid within a
proper breadth. The thickness of the pulp is regulated at the head of
the form by a brass rule standing at a certain height; its function is
to level the pulp and distribute it at a certain thickness. The
continually moving pulp layer assumes greater consistency the nearer
it approaches to the dandy roll. This is a cylinder covered with brass
wire, and is for the purpose of compressing the paper, after it has
left the form, and free it from a great part of the water, which
escapes into a box. The paper is now freed of a good deal of the
fluid, and assumes a consistency with which it is enabled to leave the
form, which now commences to return underneath the paper, passing on
to an endless felt, which revolves around rollers and delivers it to
two iron rolls. The paper passes through a second pair of iron
rollers, the interiors of which are heated by steam. These rollers
cause the last of the water to be evaporated, so that it can then be
rolled upon reels. A special arrangement shaves the edges to the exact
size required.

The paper is made in different thicknesses and designated by numbers
to the size and weight.

Waste paper, bookbinders' shavings, etc., can be used for making the
paper. As much wool as possible should be employed, because the wool
fiber has a greater resistance than vegetable fiber to the effects of
the temperature. By wool fiber is understood the horny substance
resembling hair, with the difference that the former has no marrowy
tissue. The covering pellicle of the wool fiber consists of flat,
mostly elongated leaves, with more or less corners, lying over each
other like scales, which makes the surface of the fiber rough; this
condition, together with the inclination of curling, renders it
capable of felting readily. Pure wool consists of a horny substance,
containing both nitrogen and sulphur, and dissolves in a potash
solution. In a clean condition, the wool contains from 0.3 to 0.5 per
cent. of ash. It is very hygroscopical, and under ordinary
circumstances it contains from 13 to 16 per cent. humidity, in dry air
from 7 to 11 per cent., which can be entirely expelled at a
temperature of from 226 to 230 degrees Fahrenheit. Wool when ignited
does not burn with a bright flame, as vegetable fiber does, but
consumes with a feeble smouldering glow, soon extinguishes, spreading
a disagreeable pungent vapor, as of burning horn. By placing a test
tube with a solution of five parts caustic potash in 100 parts water,
a mixture of vegetable fibers and wool fibers, the latter dissolve if
the fluid is brought to boiling above an alcohol flame, while the
cotton and linen fibers remain intact.

The solubility of the woolen fibers in potash lye is a ready means of
ascertaining the percentage of wool fiber in the paper. An exhaustive
analysis of the latter can be performed in the following manner: A
known quantity of the paper is slowly dried in a drying apparatus at
temperature of 230° Fahrenheit, until a sample weighed on a scale
remains constant. The loss of weight indicates the degree of humidity.
To determine the ash percentage, the sample is placed in a platinum
crucible, and held over a lamp until all the organic matter is burned
out and the ash has assumed a light color. The cold ash is then
moistened with a carbonate of ammonia solution, and the crucible again
exposed until it is dark red; the weight of the ash is then taken. To
determine the percentage of wool, a sample of the paper is dried at
230° Fahrenheit and weighed, boiled in a porcelain dish in potash lye
12° B. strong, and frequently stirred with a glass rod. The wool fiber
soon dissolves in the potash lye, while the vegetable fiber remains
unaltered. The pulpy mass resulting is placed upon a filter, dried at
212° Fahrenheit, and after the potash lye has dripped off, the
residue, consisting of vegetable fiber and earthy ash ingredients, is
washed until the water ceases to dissolve anything. The residue dried
at 212° Fahrenheit is weighed with a filter, after which that of the
latter is deducted. The loss of weight experienced is essentially
equal to the loss of the wool fiber. If the filtrate is saturated with
hydrochloric acid, the dissolved wool fiber separates again, and after
having been collected upon a weighed filter, it may be weighed and the
quantity ascertained.

The weight of the mineral substances in the raw paper is ascertained
by analyzing the ash in a manner similar to that above described. The
several constituents of the ash and the mineral added to the raw paper
are ascertained as follows: Sufficient of the paper is calcined in the
manner described; a known quantity of the ash is weighed and thrown
into a small porcelain dish containing a little distilled water and an
excess of chemically pure hydrochloric acid. In this solution are
dissolved the carbonates, carbonate of lime, carbonate of magnesia, a
little of sulphate of alumina, as well as metallic oxides, while
silicate of magnesia, silicic acid, sulphate of lime (gypsum) remain
undissolved. The substance is heated until the water and excess of
free hydrochloric acid have been driven off; it is then moistened with
a little hydrochloric acid, diluted with distilled water and heated.
The undissolved residue is by filtering separated from the dissolved,
the filter washed with distilled water, and the wash water added to
the filtrate. The undissolved residue is dried, and after the filter
has also been burned in due manner and the ash added, the weight is
ascertained. It consists of clay, sand, silicic acid and gypsum.

The filtrate is then poured into a cylinder capable of holding 100
cubic centimeters, and furnished with a scale; sufficient distilled
water is then added until the well-shaken fluid measures precisely 100
cubic centimeters. By means of this measuring instrument, the filtrate
is then divided into two equal portions. One of these parts is in a
beaker glass over-saturated with chemically pure chloride of ammonia,
whereby any iron of oxide present and a little dissolved alumina fall
down as deposit. The precipitate is separated by filtering, washed,
dried at 212° Fahrenheit and weighed. To the filtrate is then added a
solution of oxalate of ammonia until a white precipitate of oxalate of
lime is formed. This precipitate is separated by filtering, washed,
dried and when separated from the filter, is collected upon dark
satinized paper; the filter itself is burned and the ash added to the
oxalate of lime. This oxalate of lime is then heated to a dark red
heat in a platinum crucible with lid until the oxalate of lime is
converted into carbonate of lime. By the addition of a few drops of
carbonate of ammonia solution and another slight heating of the
crucible, also the caustic lime produced in the filter ash by heating,
is reconverted into carbonate of lime, and after cooling in the
exsiccator, the whole contents of the crucible is weighed as
carbonate of lime, after deducting the known quantity of filter ash.

Any magnesia present in the filtrate of the oxalate of lime is by the
addition of a solution of phosphate of soda separated as phosphate of
ammonia and magnesia, after having stood twenty-four hours. The
precipitate is filtered off, washed with water to which a little
chloride of ammonia is added, dried, and after calcining the fiber and
adding the filter ash, glow heated in the crucible. The glowed
substance is weighed after cooling, and is pyrophosphate of magnesia,
from which the magnesia or carbonate of magnesia is calculated
stoichiometrically. All the ascertained sums must be multiplied by 2,
if they are to correspond to the analyzed and weighed quantity of ash.

The second half of the filtrate is used for determining the small
quantity of sulphate of lime still contained in the hydrochlorate
solution. By adding chloride of barium solution the sulphuric acid is
bound to the barytes and sulphate of baryta separates as white
precipitate. This is separated by filtering, washed, dried and weighed
in the customary manner. From the weight of the sulphate of baryta is
then computed the weight of sulphate of lime, which has passed over
into solution. The ascertained sum is also to be multiplied with 2.

The manufacture of roll tar paper from the roll paper was at first
found to be difficult, as it was impossible to submerge a surface
larger than from ten to fifteen square yards, rolled up, in the tar,
because more would have required too large a pan. Besides this, the
paper tears easily, when it is in the hot tar. All kinds of
experiments were tried, in order to impregnate the surface of the
paper without employing too large a pan.

The following method was tried at first: The roll paper was cut into
lengths of ten yards, which were rolled up loosely, so that a certain
space was left between the different coils. These loose rolls, of
course, occupied much space and could be put into the tar only in a
standing position, because in a horizontal one the several coils would
have pressed together again. The loose roll was therefore slipped over
a vertical iron rod fastened into a circular perforated wooden foot.
The upper end of this iron rod ended in a ring, in which the hook of a
chain or rope could be fastened. With the aid of a windlass the roll
was raised or lowered. When placed in the pan with boiling tar, it was
left there until thoroughly saturated. It was then taken out, placed
upon a table, and the excess of tar allowed to drip off into a vessel
underneath. After partially drying, the roll was spread out in open
air, occasionally turned, until sufficiently dried, when it was rolled
up again.

In order to neutralize the smeary, sticky condition of the surface and
avoid the disagreeable drying in open air, the experiment of strewing
sand on the sticky places was tried next. The weight of the paper was
largely increased by the sand, and appeared considerably thicker. For
this reason the method of sanding the paper was at once universally
adopted. To dispense with the process of permitting the surplus tar to
drip off, means were devised by which it was taken off by scrapers, or
by pressing through rollers. The scrapers, two sharp edged rods
fastened across the pan, were then so placed that the paper was drawn
through them. The excess of tar adhering to its surface was thereby
scraped off and ran back into the pan.

This work, however, was performed better and to more satisfaction by a
pair of rollers fastened to the pan. These performed a double duty;
thoroughly removed the tar from the surface and by reason of their
pressure they caused a more perfect incorporation of the tar with the
fibers of the paper. Finally, different factories employed different
methods of manufacture, one of which was to cut the rolls into
definite lengths of about ten yards; these were then rerolled very
loosely and immersed in the hot tar until sufficiently saturated. The
paper was then passed through the roller, much pressure exerted, and
then loosely rolled up again. Being tarred once, it was then laid into
a second pan with hot tar, reeled out after a time, strewn with sand,
and rolled up again. Another method was to cut clothes lines into
lengths of about fifteen yards, and at a distance of two inches have
knots tied in them. The paper was cut in lengths of ten or fifteen
yards, three pieces of the knotted clothes line were then rolled
between the loose coils of paper, which was then submerged in the tar,
which on account of the knots could penetrate the paper. The paper was
next sanded by permitting its lower surface to pass over dry sand in a
box standing on the floor. A workman rolled off the paper, and with
his hand he strews sand on the upper surface. The rolling taking place
on the edge of a table, by means of a crank, the excess of sand
dropped off.

It is said by this method two workmen, one of which tends to the
rolling and sanding, the other turning the crank, could turn out
eighty rolls per day. This method is still in use. It is useless to
describe the many antiquated methods in vogue in smaller factories,
and it can truthfully be said that nearly all of them are out of date.
It appears to be the fact of almost all inventions that when reduced
to practical use, the arrangements, apparatus, and working methods
employed are generally of the most complicated nature, and time and
experience only will simplify them. This has been also the case with
the methods in the roofing paper industry, which are at present
gradually being reduced to a practical basis. The method gradually
adopted has been described in the preceding. The pan is of a certain
length, whereby it becomes possible to saturate the paper by slowly
drawing it through the heated tar. This is the chief feature. The work
is much simplified thereby and the workmen need not dip their hands
into the tar or soil them with it. The work of impregnating has become
much cleaner and easier, while at the same time the tar can be heated
to a much higher temperature. The pan is generally filled with
distilled coal tar, and the heating is regulated in such a manner that
the temperature of the impregnating mass is raised far beyond 212°
Fahrenheit. This accelerates the penetration, which takes place more
quickly as the degree of heat is raised, which may be almost up to the
boiling point of the tar, as at this degree the paper is not destroyed
by the heat. In order to prevent the evaporation of the volatile
ingredients of the tar, the pan is covered with a sheet iron cover,
with a slot at the place where the paper enters into the impregnating
mass and another at the place where it issues. The tar is always kept
at the same level, by occasional additions.

The roll of paper is mounted upon a shaft at the back end of the pan,
and by suitable arrangement of guide rollers it unwinds slowly, passes
into the tar in which it is kept submerged. The guide rollers can be
raised so that when a new roller is set up they can be raised out of
the tar. The end of the paper is then slipped underneath them above
the surface of the tar, when having passed through the squeezing
rollers, it is fastened to the beaming roller, and the guide rollers
are submerged again. A workman slowly turns the crank of the beaming
roller.

This motion draws the paper slowly through the fluid, the roll at the
back end unwinding. The speed with which the squeezing rollers are
turned is regulated in such a manner that the paper remains
sufficiently long underneath the fluid to be thoroughly impregnated
with it. The workmen quickly learn by experience how fast to turn the
crank. The hotter the tar, the more rapid the saturation; the high
degree of heat expels the air and evaporates the hygroscopic fluid in
the pores of the paper. The strong heating of the tar causes another
advantage connected with this method. The surface of the paper as it
issues from the squeezing rollers is still very hot, and a part of the
volatile oils evaporate very quickly at this high temperature. The
surface is thereby at once dried to a certain degree and at the same
time receives a handsome luster, as if it had been coated with a black
lacquer. The paper is sanded in a very simple manner without the use
of mechanical apparatus; as it is being wrapped into a coil, it passes
with its lower surface over a layer of sand, while the workman who
tends to rolling up strews the inside with sand. The lower surface is
coated very equally. Care only being necessary that the sand lies
smooth and even at all times. When the workman has rolled up ten or
fifteen yards, he cuts it across with a knife and straightedge, so
that the paper is cut at right angles with its sides.

There are three different sorts of roofing paper, according to the
impregnating fluid used in its manufacture. The ordinary tar paper is
that saturated with clear cold tar. This contains the greatest amount
of fluid ingredients and is very raggy in a fresh condition. It is
easy to see that the volatile hydrocarbons evaporate in a short time,
and when expelled, the paper becomes stiffer and apparently drier.
This drying, or the volatilization of the hydrocarbons, causes pores
between the fibers of the paper. These pores are highly injurious to
it, as they facilitate a process of decomposition which will ruin it
in a short time.

Roofing paper can be called good only when it is essentially made from
woolen rags, and contains either very few or no earthy additions. It
is beyond doubt that the durability of a roofing paper increases with
the quality of wool fiber it contains--vegetable fibers and earthy
additions cause a direct injury. Reprehensible altogether is any
combination with lime, either in form of a carbonate or sulphate,
because the lime enters into chemical combination with the
decomposition products of the tar.

The general nature of gravel is too well known to require description.
The grains of quartz sand are either sharp cornered or else rounded
pieces of stone of quartz, occasionally mixed with grains of other
amorphous pieces of silica--such as horn stone, silicious slate,
carnelian, etc.; again, with lustrous pieces of mica, or red and white
pieces of feldspar. The gravel used for a tar paper roof must be of a
special nature and be prepared for the purpose. The size of its grains
must not exceed a certain standard--say, the size of a pea. When found
in the gravel bank, it is frequently mixed with clay, etc., and it
cannot be used in this condition for a roof, but must be washed. The
utensils necessary for this purpose are of so simple and suggestive a
nature that they need not be described. Slag is being successfully
used in place of the gravel. It is easily reduced to suitable size, by
letting the red hot mass, as it runs from the furnace, run into a
vessel with water. The sudden chilling of the slag causes it to burst
into fragments of a sharp cornered structure. It is next passed
through a sieve, and the suitably sized gravel makes an excellent
material, as it gives a clean appearance to the roof.

The thinking mind can easily go one step further and imagine that,
since the tar contains a number of volatile hydrocarbons, it might be
made more adaptable for impregnation by paper by distilling it, as by
this process the fluid would lose its tendency to evaporate and the
percentage of resinous substances increase. Singular to say, there was
a prejudice against the employment of distilled tar, entertained by
builders and people who had no knowledge of chemistry. Increasing
intelligence and altered business circumstances, however, brought
about the almost universal employment of distilled tar, and every
large factory uses it at present. The roofing paper prepared with
distilled tar is perhaps most suitably called asphaltum paper, as this
has been used in its manufacture. It possesses properties superior to
the ordinary tar paper, one of which is that immediately after its
manufacture, as soon as cold, it is dry and ready for shipment; nor
does it require to be kept in store for a length of time, and it has
also a good, firm body, being as flexible and tough as leather. It is
very durable upon the roof, and remains flexible for a long time. It
is true that asphaltum papers will always in a fresh state contain a
small percentage of volatile ingredients, which after a while make it
hard and friable upon the roof; but, by reason of its greater
percentage of resinous components, it will always preserve a superior
degree of durability and become far less porous. One hundred parts by
weight absorb 140 or 150 parts by weight of coal tar. A factory which
distilled a good standard tar for roofing paper recovered, besides
benzole and naphtha, also about ten per cent. of creosote oil, used
for one hundred parts raw paper, 176.4 partially distilled tar.
Experiments on a larger as well as a smaller scale reduced this
quantity to an average of 141.5 parts for one hundred parts raw paper.
The weight of sanded paper is very variable, as it depends altogether
upon the size of the sand grains. It may be stated generally that the
weight of the sand is as large as that of the tarred paper.

The kinds of roofing paper saturated with other additions besides coal
tar form a separate class, in order to neutralize the defects inherent
in coal tar. These additions were originally for the purpose of
thickening the paper and making it stiffer and drier. The most
ordinary and cheapest thickener was the coal pitch. Although the
resinous substances are increased thereby, still the light tar oils
remain to evaporate, and the paper prepared with such a substance
readily becomes hard and brittle. A better addition is the natural
asphaltum, because it resists better the destroying influence of the
decomposition process, and also, to a certain degree, protects the
coal tar in which it is dissolved. The addition of natural asphaltum
doubtless caused the name of "asphaltum roofing paper." Resin,
sulphur, wood tar and other substances were also used as additions;
each manufacturer kept his method secret, however, and simply pointed
out by high sounding title in what manner his paper was composed. In
most cases, however, this appellation was applied to the ordinary tar
paper; the impregnating substance was mixed only with coal pitch, or
else a roofing paper saturated with distilled tar. The costly
additions, by the use of which a high grade of roofing paper can
doubtless be produced, largely increased its price, and on account of
the constant fall of prices of the article, its use became rather one
of those things "more honored in the breach than in the observance,"
and was dispensed with whenever practicable. The crude paper is the
foundation of the roofing paper. The qualities of a good,
unadulterated paper have already been stated. At times, the crude
paper contains too many earthy ingredients which impair the cohesion
of the felted fibrous substance, and which especially the carbonate of
lime is very injurious, as it readily effects the decomposition of the
coal tar. The percentage of wool, upon which the durability of the
paper depends very largely, is very small in some of the paper found
in the market. In place of woolen rags, cheap substitutes have been
used, such as waste, which contains vegetable fibers. Since this
cannot resist the decomposition process for any length of time, it is
evident that the roofing paper which contains a noticeable quantity of
vegetable fibers cannot be very durable. To judge from the endeavors
made to improve the coal tar, it may be concluded that this material
does not fully comply with its function of making the roofing paper
perfectly and durably waterproof. The coal tar, be it either crude or
distilled, is not a perfect impregnating material, and the roofing
paper, saturated with it, possesses several defects. Let us in the
following try to ascertain their shortcomings, and then express our
idea in what manner the roofing paper may be improved. It was
previously mentioned that every tar roofing paper will, after a
greater or smaller lapse of time, assume a dry, porous, friable
condition, caused by the volatilization of a part of the constituents
of the tar. This alteration is materially assisted by the oxygen of
the air, which causes the latter to become resinous and exerts a
chemical influence upon them. By the volatilization of the lighter tar
oils, pores are generated between the fibers of the roofing paper,
into which the air and humidity penetrate. In consequence of the
greatly enlarged surface, not only the solid ingredients of the tar,
which still remain unaltered, are exposed to the action of the oxygen,
but also the fibers of the roofing paper are exposed to decomposition.
How destructive the alternating influence of the oxygen and the
atmospheric precipitations are for the roofing paper will be shown by
the following results of tests. It will have been observed that the
rain water running from an old paper roof, especially after dry
weather, has a yellowish, sometimes a brown yellow color. The
supposition that this colored rain water might contain decomposition
products of the roofing paper readily prompted itself, and it has been
collected and analyzed at different seasons of the year. After a
period of several weeks of fair weather during the summer, rain fell,
and the sample of water running from a roof was caught and evaporated;
the residue when dried weighed 1.68 grammes. It was of a brownish
black color, fusible in heat and readily soluble, with a yellow brown
color in water. The dark brown substance readily dissolved in ammonia,
alcohol, dilute acid, hydrochloric acid, sulphuric acid, and
decomposed in nitric acid, but did not dissolve in benzine or fat oil.
After several days' rain during the summer, a quantity of the water
was caught, evaporated, and the residue dried. Its characteristics
were similar to those above mentioned. By an experiment instituted in
water under conditions similar to the first mentioned, the dry brown
substance weighed 71 grammes. It possessed the same characteristics.
In the solution effected with water containing some aqua ammonia of
the brown substance, a white precipitate of oxalate of lime occurred
when an oxalate of ammonia solution was added, but the brown substance
remained in solution. A further precipitation of oxalate of lime was
produced by a solution of oxalic acid, but the brown organic substance
remained in solution. This organic substance being liberated from the
lime was evaporated, and left a dry, resinous, fusible brownish black
substance, which also dissolved readily in water. It will be seen from
these trials that the substance obtained from the rain water running
from a paper roof is a combination of an organic acid with lime, which
readily dissolves in water, and that also the free organic acid
combined with the lime dissolves easily in water.

The question concerning the origin of this organic substance or its
combination with lime can only be answered in one way, viz., that it
must have been washed by the rain water out of the paper. But since
such a solid substance, easily soluble in water, is contained neither
in the fresh roofing paper nor in the coal tar, the only deduction is
that it must have arisen by the decomposition of the tar, in
consequence of the operation of the oxygen. The lime comes from the
coating substance of the roof, for which tar mixed with coal pitch was
used. The latter was fused with carbonate of lime. These analyses
furthermore show that the formation of the organic acid easily soluble
in water depends upon the season; and that a larger quantity of it is
generated in warm, sunny weather than in cold, without sunshine. This
peculiarity of the solid, resinous constituents of the coal tar, to be
by the operation of the atmospheric oxygen altered into such products
that are readily soluble in water, makes the tar very unsuitable as a
saturative substance for a roofing paper. How rapidly a paper roof can
be ruined by the generation of this injurious organic acid will be
seen from the following calculation: Let us suppose that an average
of 132 gallons of rain water falls upon ten square feet roof surface
per year, and that the arithmetical mean 0.932 of the largest (1.680)
and smallest number (0.184) be the quantity of the soluble brown
substance which on an average is dissolved in one quart of rain water;
hence from ten square feet of roof surface are rinsed away with the
rain water per year 466 grammes of the soluble decomposition products
of the tar. The oxidation process will not always occur as intensely
as by a paper roof, ten years old and painted two years ago, which
instigated above described experiment. As long as the roofing paper is
fresh and less porous, especially if the occurring pores are filled
and closed again by repeated coatings, oxidation will take place far
less rapidly. Besides this, the protective coating applied to the roof
surface is exposed most to this oxidation process. Even by assuming
this constantly progressive destructive action of the oxygen on the
roofing paper to be much less than above stated, we can readily
imagine that it must be quite large. If it is desired to produce a
material free of faults, it is first of all indispensable that
unobjectionable raw material be procured. Coal tar was formerly used
almost exclusively for the coating of a roof. It was heated and
applied hot upon the surface. In order to avoid the running off of the
thinly fluid mass, the freshly coated surface was strewn with sand.
The most volatile portion of the tar evaporated soon, whereby the
coating became thicker and finally dried. The bad properties of the
coal tar, pointed out elsewhere, made it very unsuitable even for this
purpose, and experiments were instituted to compound mixtures, by
adding other ingredients to the tar, that should more fully comply
with its function. It may be said in general that the coating masses
for roofs can be divided into two classes: either as lacquers or as
cements. To the former may be classed those of a fairly thinly fluid
consistency, and which contain volatile oils in such quantities that
they will dry quickly. Cements are those of a thickly fluid
consistency, and are rendered thus fluid by heating. It is not
necessary that the coating applied should harden quickly, as it
assumes soon after its application a firmness sufficient to prevent it
from running off the roof. Coal tar is to be classed among lacquers.
If it has been liberated by distillation from the volatile oils, it is
made better suited for the purpose than the ordinary kind. The mass
contains much more asphaltum, and after drying, which takes place
soon, it leaves a far thicker layer upon the roof surface, while the
pores, which had formed in the roofing paper consequent on drying, are
better filled up. Nevertheless, the distilled tar also has retained
the property of drying with time into a hard, vitreous mass, and
ultimately to be destroyed by decomposition.--_The Roofer_.

       *       *       *       *       *




A PHYSICAL LABORATORY INDICATOR.


The difficulties attending the management of a physical laboratory are
much greater than those of a chemical one. The cause of this lies in the
fact that in the latter the apparatus is less complicated and the pieces
less varied. Any contrivance that will reduce the labor and worry
connected with the running of a laboratory is valuable.

A physical laboratory may be arranged in several ways. The apparatus may
be kept in a store room and such as is needed may be given to the
student each day and removed after the experiments are performed; or the
apparatus for each experiment or system of experiments may be kept in a
fixed place in the laboratory ready for assembling; for certain
experiments the apparatus may be kept in a fixed place in the laboratory
and permanently arranged for service.

Each student may have his own desk and apparatus or he may be required
to pass from desk to desk. The latter method is preferable.

When a store room is used the services of a man are required to
distribute and afterward to collect. If the apparatus is permanently
distributed, a large room is necessary, but the labor of collecting and
distributing is done away with.

There are certain general experiments intended to show the use of
measuring instruments which all students must perform. To illustrate the
use of the indicator I have selected an elementary class, although the
instrument is equally applicable to all classes of experiments.

Having selected a suitable room, tables may be placed against the walls
between the windows and at other convenient places. Shallow closets are
built upon these tables against the wall; they have glass doors and are
fitted with shelves properly spaced. A large number of light wooden
boxes are prepared, numbered from one up to the limit of the storage
capacity of the closets. A number corresponding to that upon the box is
placed upon the shelf, so that each one after removal may be returned to
its proper place without difficulty. On the front of the box is a label
upon which is written the experiment to be performed or the name of the
apparatus whose use is to be learned, references to various books, which
may be found in the laboratory library, and the apparatus necessary for
the experiment, which ought to be found in the box. If any parts of the
apparatus are too large to be placed in the box, the label indicates by
a number where it may be found in the storage case.

It is evident that, instead of the above arrangement, all the boxes can
be stacked in piles in a general store room. The described arrangement
is preferable, as it prevents confusion in collecting and distributing
apparatus when the class is large.

_The Indicator_ (see figure).--Some device is evidently desirable to
direct the work of a laboratory with the least trouble and friction
possible. I have found that the old fashioned "peg board," formerly used
in schools to record the demerits of scholars, modified as in the
following description, leaves nothing to be desired.

The requirements of such an instrument are these: It must show the names
of the members of the class; it must contain a full list of the
experiments to be performed; it must refer the student to the book and
page where information in reference to the experiments or apparatus may
be found; it must show what experiments are to be performed by each
student at a given time; it must give information as to the place in the
laboratory where the apparatus is deposited; it must show to the
instructor what experiments have been performed by each student; it must
prevent the assignment of the same experiment to two students; it must
enable the instructor to assign the same experiment to two or more
students; it must form a complete record of what has been done, what
work is incomplete, and what experiments have not yet been assigned; it
must also be so arranged that new experiments or sets of experiments may
be exhibited.

      +------+---+---+---+---+---+---+---+---+
      |      | A | B | C | D | E | F | G | H |
      +------+---+---+---+---+---+---+---+---+
      |    1 | *   o   o   *   o   o   o   o |
      |    2 | *   o   *   *   o   o   o   o |
      |    3 | +   *   *   *   o   o   o   o |
      |    4 | +   o   *   *   o   o   o   o |
      |    5 | o   +   *   *   *   *   o   o |
      |    6 | o   +   *   *   o   *   o   o |
      |    7 | o   o   +   *   o   o   o   o |
      |    8 | o   o   o   +   *   o   o   o |
      |    9 | o   o   o   *   +   o   o   o |
      |   10 | o   o   o   o   o   +   o   o |
      |   11 | o   o   o   *   o   o   +   * |
      |   12 | o   o   *   *   o   +   +   + |
      |   13 | o   o   *   o   o   o   o   o |
      |   14 | o   o   *   o   o   o   o   o |
      |   15 | o   o   +   o   o   o   o   o |
      |   16 | o   o   +   +   *   o   o   * |
      +--------------------------------------+

     A, B, C, etc., are cards upon which are the names of students. 1,
     2, 3, etc., are cards like the one described in the article. The
     small circles (o) represent unassigned experiments. The black
     circles (*) (slate nails) represent work done. The caudate circles
     (+) (brass nail) represent work assigned.

The indicator consists of a plank of any convenient length and breadth.
The front surface is divided into squares of such size that the pegs may
be introduced and withdrawn with ease. At each corner of the squares
holes are bored into which nails may be placed. There is a blank border
at the top and another on the left side. At the top of each vertical
column of holes is placed a card holder. This is made of light tin
turned up on the long edges--which are vertical--and tacked to the
board. Opposite each horizontal row of holes is a similar tin card
holder, but of greater length, and having its length horizontal. The
holders at the top of the board contain cards upon which the names of
the class are written.

Cards, like the following, are prepared for the horizontal holders.

--------------------------------------------------------------
Stewart & Gee 229
Physical Manip. 85    Intensity of Gravity--Borda's Method  39
Glazebrook & Shaw 132
--------------------------------------------------------------

These cards are numbered from one to any desired number and are arranged
in the holders consecutively.

Two kinds of nails are provided to fit the holes in the board: An
ordinary slate nail and a common picture frame nail with a brass head.
The latter indicates work to be done, the former work done.

To prepare the board for service, brass headed nails are placed opposite
each experiment, and below the names, care being taken not to have more
than one nail in the same horizontal row, unless it is intended that two
persons or more are to work upon the same experiment.

There will be no conflict when the brass nails occupy diagonal lines. If
they do not, a glance will show the fact.

After an experiment has been performed and a report made upon the usual
blank, the brass nail is removed and a slate nail put in its place.

The board will show by the slate nails what work has been done by each
student, by the brass nails what is yet to be done, and by the empty
holes, experiments which have been omitted or are yet to be assigned. A
slate nail opposite an experiment card indicates that that experiment
may now be assigned to another person.

It is evident that the schedule for a whole term may be arranged in a
few minutes and that the daily changes require very little time.

The board is hung in a convenient place. The student as he enters the
laboratory looks for his name on the upper cards and under it for the
first brass nail in the vertical column: to the left he finds the
experiment card. On the left hand end of the slip he sees the book
references, on the right hand end a number--39 in the sample card given
above. Knowing the number, he proceeds to a desk and finds a box
numbered in the same manner. He removes the box from the closet. On the
label of the box is a list of all the apparatus necessary, which he will
find in the box; the label also contains the book references. He
performs the experiment, fills up a blank which he gives to the
instructor, puts all the materials back in the box, replaces the box in
its proper place in the closet and proceeds with the next experiment.
With this indicator there is no difficulty in managing fifty students or
more.

Comparatively little apparatus need be duplicated. Where apparatus is
fixed against a wall a number may be tacked upon the wall and a card
containing the information desired. The procedure is then the same as
with the boxes. The cards on the board being removable, other ones may
be inserted containing information in reference to other boxes having
the same number but containing different materials. There can be no
successful tampering with the board, for the record of experiments
performed is upon the blanks which the students turn in and also in the
individual note books which are written up and given to the instructor
for daily examination.

Lafayette College. J.W. MOORE.

       *       *       *       *       *




NEW METHOD OF EXTINGUISHING FIRES


This is by George Dickson, of Toronto, Canada, and David Alanson Jones.

A mixture of water and liquefied carbon dioxide upon being discharged
through pipes at high pressure causes the rapid expansion of the gas and
converts the mixture into spray more or less frozen, and portions of the
liquid carbon dioxide are frozen, owing to its rapid expansion, and are
thus thrown upon the fire in a solid state, where said frozen carbon
dioxide in its further expansion not only acts to put out the fire, but
cools the surface upon which it falls, and thus tends to prevent
reignition.

A represents a receptacle sufficiently strong to stand a pressure of not
less than a thousand pounds to the square inch.

B B water receptacles.

[Illustration: Fig. 1]

In the drawings we have shown two receptacles B and only one receptacle
A; but we do not wish to confine ourselves to any particular number, nor
do we wish to confine ourselves to the horizontal position in which the
receptacles are shown.

C is a pipe leading from the receptacle A to a point at or near the
bottom of the receptacle B.

F is a pipe through which the mixture of water and liquefied gas from
the receptacle B is forced by the expansion of said liquefied gas, the
said pipe taking the mixture of water and liquefied gas from the bottom
of the receptacle.

[Illustration: Fig. 2]

To use the apparatus, open the stop cock D in the pipe C, leading to one
of the receptacles B, whereupon, owing to the lower pressure in the
cylinder B, the liquid carbon dioxide expands and rises to the top of
the cylinder A and forces the liquid carbon dioxide into the cylinder B,
the same as the superior steam of a boiler forces the water of the
boiler out when the same is tapped below the surface of the liquid. Now
upon opening the tap H, this superior gas forces out the mixture of
water and liquid carbon dioxide, which suddenly expanding causes
portions of the globules of liquefied gas to be frozen, and these, being
protected by a rapidly evaporating portion of the liquefied gas, are
thrown on the fire in solid particles. At the same time the water is
blown into a spray, which is more or less frozen. The fire is thus
rapidly extinguished by the vaporization of the carbon dioxide and water
spray.

       *       *       *       *       *




SMOKELESS GUNPOWDER.

BY HUDSON MAXIM.


During the last forty years leading chemists have continued to
experiment with a view to the production of a gunpowder which should be
smokeless. But not until the last few years has any considerable degree
of success been attained.

To be smokeless, a gunpowder must yield only gaseous products of
combustion. None of the so-called smokeless powders are entirely
smokeless, although some of them are very nearly so.

The smoke of common black gunpowder is largely due to minute particles
of solid matter which float in the air. About one-half of the total
products of combustion of black gunpowder of ordinary composition
consists of potassium carbonate in a finely divided condition and of
potassium sulphate, which is produced chiefly by the burning in the air
of potassium sulphide, another production of combustion, as on the
outrushing gases it is borne into the air in a fine state of division.

Another cause for the smoke of gunpowder is the formation of small
liquid vesicles which condense from some of the products of combustion
thrown into the air in a state of vapor, in the same manner as vesicles
of aqueous vapor form in the air on the escape of highly heated steam
from the whistle of a locomotive.

Broadly speaking, an explosive compound is one which contains, within
itself, all the elements necessary for its complete combustion, and
whose heated gaseous products occupy vastly more space than the original
compound. Such compound usually consists of oxygen, associated with
other elements, for which it has great affinity, and from which it is
held from more intimate union, or direct chemical combination, under
normal conditions, by being in combination as well with other elements
for which it has less affinity, but which it readily gives up for the
stronger affinities when explosion takes place, the other elements
either combining with one another to form new compounds or being set
free in an uncombined state.

An explosive is said to detonate when the above changes take place
instantaneously, the action being transmitted with the speed of
electricity by a sort of molecular rhythm from molecule to molecule
throughout the entire substance of the compound.

An explosive is said to explode when the above changes do not occur
instantaneously throughout the whole substance, but whose combustion
takes place from the surface inward of the particles or grains of which
it is composed, thus requiring some definite lapse of time.

The elements of an explosive compound may be associated chemically as in
nitro-glycerine and gun-cotton, which are chemical compounds, being the
results of definite reactions. Or, an explosive may be a mere mechanical
mixture of different substances comprising the necessary elements, as is
ordinary black gunpowder, which is a compound of charcoal, sulphur and
saltpeter, the saltpeter supplying the necessary oxygen.

No gunpowder can be smokeless in which saltpeter or any oxygen-bearing
salt having a metallic base is employed, for when the salt gives up its
oxygen, the base combines with other elements to produce a sulphate, a
carbonate, or other salt, which, being solid, produces smoke. Therefore,
to be smokeless, a gunpowder must contain no other elements than oxygen,
hydrogen, nitrogen, and carbon, and in such proportions that the
products of combustion shall be wholly gaseous. The nitric
ethers--gun-cotton and nitro-glycerine--constitute such explosive
compounds. These substances were formerly thought to be
nitro-substitution compounds, but are now known to belong to the
compound ethers of nitric acid.

Gun-cotton, discovered by Schonbein, in 1845, has since been looked upon
as the most promising material for a smokeless gunpowder, it being a
very powerful explosive and burning with practically no smoke. To-day,
gun-cotton, in some form or other, constitutes the base of substantially
all of the smokeless powders with which have been attained any
considerable degree of success.

Gun-cotton alone and in its fibrous state has been found to be too
quick, or violent, for propulsive purposes, such as use in firearms; as
under such conditions of confinement it is very likely to detonate and
burst the gun. However, if gun-cotton be dissolved in a suitable
solvent, which is capable of being evaporated out, such as acetone, or
acetate of ethyl, which are very volatile, it becomes, when thus
dissolved and dried, a very hard, horn-like, amorphous substance, which
may be used for a smokeless gunpowder. But this substance taken alone is
very difficult to mould or granulate, and the loss of expensive solvents
must necessarily be quite considerable.

When gun-cotton is reduced to a collodial solid, as above, and used as a
smokeless gunpowder, the grains must be made comparatively small to
insure prompt and certain ignition, and consequently the pressures
developed in the gun are apt to be too great when charges sufficiently
large are used to give desired velocities.

If, however, a compound be made of gun-cotton and nitro-glycerine, in
about equal parts, by means of a volatile solvent or combining agent,
such as one of the before mentioned, and the solvent evaporated out, we
obtain practically a new substance and one which, as regards its
explosive nature, is quite unlike either of its two constituents taken
alone. The nitro-glycerine, furthermore, being itself a solvent of
gun-cotton, much less of the volatile ether is necessary to render the
compound of an amorphous character. Being quite plastic this substance
may be wrought or moulded into any desired size or form of grain.

This simple compound of nitro-glycerine and gun-cotton, or with some
slight modifications, has been found, when properly granulated, to be
the most smokeless powder that has yet been discovered or invented. If
pure chemicals are employed in the manufacture, and the gun-cotton and
nitro-glycerine be made of the highest nitration and best quality, we
have a smokeless powder which will possess the following desirable
qualities:

1st. It is absolutely smokeless, that is, its products of combustion are
entirely gaseous.

2d. Its products of combustion are in no way deleterious or unpleasant.

3d. It is perfectly safe to manufacture, handle and transport. There is
no more danger of its exploding accidentally than there would be of an
explosion of shavings or sawdust; for, unless well confined and set off
with a strong primer, it will not explode at all. In the open its
combustion is so slow as to in no way resemble or partake of the nature
of an explosion.

4th. It is perfectly stable, and will keep any length of time absolutely
without undergoing any change whatever, under all conditions of
temperature or exposure to which gunpowder would ever be subjected.

5th. It is not hygroscopic, and may be soaked in water without being at
all affected by it.

6th. It will not corrode the cartridge case.

7th. It will not foul the gun.

8th. It is sure of ignition with a good primer, and may be made to burn
as slowly as desired by varying the character and size of the grains.
Indeed, it may be made to burn so slowly as to fail of complete
combustion before the bullet leaves the gun, and after firing several
rounds, partly burned pieces of the powder may be picked up in front of
the gun.

9th. In a shoulder arm, a velocity of 2,000 feet per second may be
imparted to the bullet with this powder, and with a pressure in the
chamber of the gun of not more than fifteen English tons. This is, of
course, when the gun, cartridge case, primer, and projectile are adapted
to the use of smokeless powder, and the granulation of the powder is
adapted to them.

If what I have here claimed for the above smokeless powder be true, it
would appear that it may be taken as really an ideal smokeless powder.
Why, then, has it not already been universally adopted? Surely such a
powder is just what every government is seeking. In reply to this, let
me say that, in order for the above compound to be an effective and
successful smokeless powder, with the manifestation of the many
desirable qualities which I have recited, a great many other conditions
are necessary, some of which I will mention. To arrive at the knowledge
that this compound would constitute the best smokeless powder has
required a great deal of experimenting. It was first thought that
gun-cotton colloid, without any nitro-glycerine, that is, gun-cotton
dissolved and dried, would burn more slowly, keep better, and give
better ballistics than it would if combined with nitro-glycerine. It was
also thought that gun-cotton of a high degree of nitration when made
into colloidal form would even then burn too quickly to be suitable for
use in firearms. Consequently, the first experiments were with low grade
gun-cotton, what is called collodion cotton, such as is employed in the
manufacture of celluloid. But, as this would not explode without the
addition of some oxygen-bearing element, various oxygen-bearing salts
were combined with it, such as nitrate of potassium, nitrate of ammonia,
nitrate of baryta, etc. Also a great many of the first smokeless powders
were made of low grade gun-cotton combined with nitro-glycerine in
varying proportions. These powders would often give very good results
when first made; but low grade gun-cotton or di-nitro-cellulose, as it
is called, is a very unstable compound, and these powders, after giving
very promising results, were found to be constantly undergoing change,
sooner or later resulting in complete decomposition.

When nitro-glycerine was first combined with gun-cotton in small
quantities, camphor was often added, to lessen the rapidity of
combustion which the nitro-glycerine was supposed to impart and also to
render the compound more plastic, and to tend to prevent the
decomposition of the low grade gun-cotton. But camphor being volatile,
would, by its evaporation, cause the powder to constantly change in
character. Castor oil has been found to be a better diluent, as this
will not evaporate.

As all of the smokeless powders made of a low grade gun-cotton were
found to deteriorate and spoil, experiments were made with gun-cotton of
the highest degree of nitration, both alone and in combination with
nitro-glycerine. These experiments were first conducted in England by
private parties and by the British government, when it was found that
high grade gun-cotton would give excellent results if made into a
colloidal solid and used alone, or in combination with certain other
constituents. With a view to saving the large quantity of solvents
necessary to reduce the gun-cotton, and to get a more prompt and certain
ignition with a larger grain, experiments were cautiously made by the
admixture of varying proportions of nitro-glycerine to the gun-cotton
when dissolved, or rather along with other solvents in the process of
dissolving it.

It was soon found that nitro-glycerine added in quantities, even equal
in weight to the gun-cotton itself, did not materially increase the
rapidity of the explosion of the compound. And it was also found that
high grade gun-cotton, when combined with nitro-glycerine, gave very
much better results than low grade gun-cotton.

I have spoken here of high and low grade gun-cotton, when in fact the
word gun-cotton should be applied only to the highest nitro-compound of
cellulose. The word gun cotton has always been rather loosely used.
Pyroxyline would be a better word, as this applies to all grades. When
cotton fiber is soaked in a large excess of a mixture of the strongest
nitric and sulphuric acids, gun-cotton proper, or that of the highest
grade, is produced. When weaker acids are used, lower grades of
nitro-cellulose are formed.

The first mentioned or highest grade gun-cotton, when thoroughly freed
from its acids, has always proved to be a perfectly stable compound. The
lower grades have always been found to be unstable and subject to
spontaneous decomposition. Nitro-glycerine has also been erroneously
thought to be a very unstable compound. But experiments have proved
that, when made pure, it is perfectly stable.

Having now explained how the knowledge came to be arrived at that the
aforementioned compound of highest grade nitro-glycerine and highest
grade gun-cotton would constitute the best basis for a smokeless powder,
I will now mention a few of the other conditions necessary to success
with its use, without assuming that smokeless powder has yet passed its
experimental stage, and is beyond further improvement. Nevertheless,
such is the compound which has come to stay as the basis of all
smokeless powders; and any smokeless powder, if a successful one, may be
counted upon as being made of this compound of gun-cotton and
nitro-glycerine, or of a colloid of gun-cotton, either alone or combined
with diluents, oxygen-bearing salts, or inert matter. The fact that
smokeless powder may still be said to be in somewhat of an experimental
stage is not to admit that it is not a success. Firearms, cartridge
cases, and projectiles are also still in an experimental stage, for they
are constantly being improved; yet their use has been a great success
for a good many years.

The question of success of a smokeless powder does not rest alone with
the powder itself. The gun, the cartridge case, primer, and bullet have
been as much the subjects of experiments in adapting them to the use of
smokeless powder as has the smokeless powder in being adapted to them.
To impart a velocity of 2,000 feet per second to a rifle ball, with
corresponding long range and accuracy of flight, has been a question as
much of improvement in rifles and projectiles as in the powder. To give
a velocity of 2,000 feet per second to a bullet, requires a pressure of
at least 15 English tons in the chamber of a gun. This would be a
dangerous pressure in an old-fashioned shoulder arm; while a bullet made
only of lead would strip on striking the rifling and pass right through
the barrel of the gun without taking any rotary motion whatever. It
might at first seem that the powder is the only thing to be considered;
but high ballistics can only be obtained when everything else is adapted
to its use.

The projectile, the cartridge case, the fulminating cap, and the gun
have had to be all built up together, and a very large amount of
experimenting has been necessary to determine what would constitute the
best projectile, best cartridge case, best fulminating cap, and what
should be the character of the rifling and the quality and temper of the
steel of the gun barrel.

It has been necessary first to conduct experiments to test the smokeless
powders for velocities and pressures, and then with the powders test
various kinds of projectiles and guns. In order to obtain the high
ballistics which have been secured, it has been found necessary to cover
the bullet with something harder than lead and to rifle the gun in a
special manner.

The French, who were the first to definitely adopt smokeless powder,
were the first also to make a rifle, projectile, cartridge case and
primer suited to its use.

To obtain long range with a small long bullet such as is now used, it
should rotate at a very high speed. It is well known to artillerists
that a projectile of four or more calibers in length has to be rotated
at a much higher speed than one of half that length, in order to keep
the projectile stiff in the air, and to prevent it from ending over in
its flight. To communicate this very high rotary movement to the bullet
in the instant of time during which it is passing through the barrel,
the rifling of the gun has to exert an enormous torsion on the bullet.
Lead, no matter how hardened, is not sufficiently strong, as it will not
only strip and pass straight through the gun without taking any rotary
movement whatever, but under such very high pressures it behaves like
wax, and is thrown from the gun in a distorted mass.

The French cover their bullets with German silver, a substance made of
nickel, zinc and copper; and in order to put as little strain upon the
rifling and projectile as possible, the rifling of the gun is made with
an increasing twist, and has no sharp edges. The French rifle is made
very strong at the breech and is of tempered steel throughout. In this
way the French have made smokeless powder a success--a smokeless powder
made substantially of a character such as I have herein described. With
smokeless powder, the French rifle imparts a muzzle velocity of 2,000
feet per second to the bullet, with a range of about 2,400 meters.

If smokeless powder be divided into sufficiently small grains to be
ignited by an ordinary fulminating cap, it would burn too quickly,
thereby causing the pressure to mount too high, and without giving the
desired velocity. Consequently very large and strong fulminating caps
have to be employed. Smokeless powder is not ignited in the same manner
as black powder. Something besides ignition is necessary. Black powder
simply requires to be set on fire; while a smokeless powder, on the
contrary, not only requires that it be set on fire, but that a certain
degree of pressure be set up inside of the cartridge case. For instance,
if a primer of a certain size should be found to operate perfectly well,
giving prompt ignition in the cartridge case of a rifle of small
caliber, it would be found that the same primer would not ignite a
charge of the same powder if loaded into a gun of one inch caliber. In
the latter case a few grains only lying near the primer would be
ignited, and these would soon become extinguished by sudden release of
pressure bringing about a cooling effect due to expansion of the gases.
In small cartridges a large fulminating cap is all that is required, but
in large cartridges it is necessary to resort to additional means of
ignition.

In France, where experiments were conducted with a 37 millimeter Maxim
gun, it was found to be impracticable to use a fulminating cap
sufficiently large to ignite the powder and cause it to burn. Therefore,
a small ignition charge of black powder was employed, it being put in a
capsule or bag and placed next the primer. On firing at the rate of 300
rounds per minute, the black powder, though small in quantity, produced
a cloud of smoke through which it was quite impossible to see. The
inventor of the gun then prepared for the French some wafers of
pyroxyline canvas, which were placed next to the primer, securing
thereby prompt ignition without the production of any smoke.

Smokeless powder, made as I have described, cannot be detonated by a
fulminating cap of any size or by any means whatever. A large charge of
fulminate of mercury placed inside the cartridge case next the primer
will not detonate the powder, it serving only to ignite it and cause it
to explode. But even this would not cause the powder to explode except
it be confined behind a projectile, that sufficient pressure may be run
up to make it burn in its own gases.

Some curious experiments with smokeless powder may be tried with a shot
gun. If the fulminating cap be large, the powder fine, the wads numerous
and hard and the charge of shot heavy, all being well rammed down, and
the paper case well spun over the last pasteboard wad, a charge of
smokeless powder about equal in weight to one-half of what would be
employed of black powder would give about the same results as black
powder. But if the charge of shot be omitted, the primer will only
ignite the powder, and there will be set up sufficient pressure merely
to throw the wads about half way up the barrel of the gun, when the
powder will go out. Now if this same charge of powder be collected and
reloaded into a new cartridge case and well confined behind wads and a
charge of shot, as above explained, it will all burn, giving the same
results as black powder.

Attempts have been made to use this powder in pistols and revolvers, but
here it has proved a failure, as the pressure is not great enough to
cause the powder to be consumed, unless it be in the form of very fine
grains or dust, in which case the pressure mounts too high. However,
this might be overcome to a degree by making the powder porous. The
chemical conditions of the powder might be the same, but the physical
conditions must be different. A powder suitable for shot guns and
pistols would not be suitable for rifles.

One not familiar with the characteristics of smokeless powder would be
almost certain to fail in his first attempt to fire it. Many persons
have been convinced by their first experiments that this powder would
not burn at all in a gun, any more than so much sand.

Smokeless powder is consumed with a rapidity which accords with the
conditions of its confinement. Therefore, the bullets which have been
experimented with by different governments have been the cause of much
of the varying pressures attributed to the smokeless powders.

The Austrians use the Mannlicher steel jacketed bullet. The steel casing
or jacket is first tinned on the inside and then the lead is cast in,
thus melting the tin and adhering firmly to the jacket. This projectile
sets up enormous friction in the barrel of the gun when used with
smokeless powder; as the smokeless powder leaves the gun barrel
perfectly clean and the two steel surfaces being in absolute contact
cause tremendous friction; and as the coefficient of friction varies
with every shot, the pressure in the gun constantly varies greatly.

The German silver covered bullet used by the French has the disadvantage
that when firing rapidly the chamber of the barrel becomes nickel plated
and great friction is caused, mounting up the pressures and causing the
muzzle velocities to fall off.

The Austrians, in order to prevent their steel cased bullets from
rusting and to lessen the friction in the barrel of the gun, cover them
with a heavy lubricant, which gives the cartridges an unsightly
appearance and causes them to gather dust and sand. The French employ a
lubricant at the base of the projectile, with a small copper disk
between the same and the powder.

Col. A.R. Buffington, commander of the National Armory at Springfield,
Mass., has made a steel covered projectile which he prevents from
rusting by blackening by a niter process. Several grooves are pressed in
the base of the bullet which carry a lubricant, and when the bullet is
inserted in the cartridge case the grooves are covered by it.
Furthermore, these grooves prevent the lead filling from bursting
through the steel casing, leaving the latter in the barrel, as often
occurs with the Austrian and French projectiles when using smokeless
powder.

A new projectile has lately come out, the invention of Captain Edward
Palliser, of the British army. This bullet consists of a jacket made of
very soft Swedish wrought iron, coated with zinc and filled with lead,
the lead being pressed into this jacket. The bullet is corrugated at its
base, after the manner of the one made by Colonel Buffington. This
projectile has been experimented with very extensively by the British
government, and at the works of the Maxim-Nordenfelt Guns and Ammunition
Company, in England. The zinc coating of the bullet is too soft to stick
to the barrel of the gun, and also in a measure acts as a lubricant.
This projectile has given better results than any other that has been
experimented with. The great velocities and the most uniform pressures
by the use of smokeless powder have been attained with this Palliser
bullet.


NOISELESSNESS.

A great many stories have been told about the noiselessness of smokeless
powder. But there is no such thing as a noiseless gunpowder. The report
of a gun charged with smokeless powder is very sharp, and is as loud as
when black powder is used, yet the volume of sound is much less, so that
the report cannot be heard at so great a distance.

The report of a gun using smokeless powder is a sound of much higher
pitch than when black powder is used, and consequently cannot be heard
at so great a distance as the lower notes given by black powder.

As smokeless powder exerts a much greater pressure than common black
powder when burned in a gun, one would naturally think that the recoil
of the barrel would be greater, owing to the greater pressure exerted by
the smokeless powder on the base of the cartridge case and the breech
mechanism. However, such is not the fact; for the barrel actually
recoils very much less when smokeless powder is used. This is due to the
suddenness with which the pressure is exerted by smokeless powder, it
acting more like a very sharp blow on the metal, whereby more of the
energy is converted into heat instead of being spent in overcoming the
inertia of the barrel to give recoil. Similarly when smokeless powder is
fired in a gun, the displacement of the air is so sudden that the sound
waves do not possess the same amplitude of recoil or vibration as is
given by black powder.

       *       *       *       *       *




THE CONSTRUCTION AND MAINTENANCE OF UNDERGROUND CIRCUITS.

BY S.B. FOWLER.


The numerous disastrous storms of the last winter have brought out very
vividly the advantages of having all wires placed underground, and many
inquiries have been addressed to the companies operating underground
circuits as to their success. It is not probable that all of the answers
to these inquiries have been of the most favorable character. To many
central station managers an underground system means frequent
break-downs and interruptions of service, with, perhaps, slow and
expensive repairs, which bring in their turn numerous complaints, loss
of customers, and reduced profits. In many installations burn-outs both
underground and in the station are frequent, with the natural result
that the operating of circuits underground is not there considered an
unqualified success. The writer has in mind two very different
experiences with underground cables. Several miles of cable were bought
by a certain company, carefully laid, and up to to-day not a single
burn-out or interruption of service can be attributed to failure of
cables; at about the same time another company bought about an equal
amount of the same kind of cable, and in a comparatively short time the
current had to be shut off the lines and the whole installation repaired
and parts of it replaced. Both of these experiences have been repeated
many times and will be again, although it is simply a distinction
between a good cable properly laid and a good cable ruined by careless
and incompetent workmanship.

Every failure can be traced to poor work in the original installation or
to the use of a cheap cable, both causes being due, generally, to that
false economy which looks for too quick returns. A poorly insulated line
wire and a poorly insulated cable are two very different things.
However, it is a fact that by the use of a good cable it is not
difficult to construct an underground system for light, power, telegraph
or telephone uses that will be superior to overhead lines in its service
and in cost of maintenance. The ideal underground system must have as a
starting point a system of subways admitting of the easy drawing in and
out of cables and affording means of making subsidiary connections
readily and with the minimum of expense and interruption of service.
This is practically accomplished by a subway consisting of lines of pipe
terminating at convenient intervals, say at street intersections, in
manholes, for convenience in jointing and in running out house
connections. These pipes, or ducts, as they are called, should be for
two kinds of service; the lower or deeper laid lines for the main or
trunk circuits, and a second series of ducts laid nearer the surface,
running into service boxes placed near together for lines to "house to
house" connections. In some cities where it is allowed to run overhead
lines, the plan of running but one service connection in a block is
followed, all customers in the block being supplied from a line run over
the housetops or strung on the rear walls.

This makes unnecessary all subsidiary ducts except a short one from the
manhole to the nearest building in the block, and effects a considerable
saving in pipe, service boxes, cables and labor. The manholes should
have their walls built up of brick, the floors should be of concrete,
and there should be an inside lid which can be fastened down and the
manhole thus made water-tight.

For ducts wood, iron or cement lined pipe may be used. To preserve the
wood it is generally treated with creosote, which, in contact with the
lead cover of the cable, sets up a chemical action, resulting in the
destruction of the lead. Wood offers but little protection for the
cable, as it is too easily damaged and broken through in the frequent
street openings made by companies operating lines of pipe in the
streets, and as one of the main purposes of a subway is that of a
protection to cables, wooden ducts have little to recommend them except
their cheapness.

Iron pipes are either laid in trenches filled in with earth or are laid
in cement. Iron pipe will of course rust out in time, and if absolute
permanence in construction is desired, should be laid in cement, for
after the pipe rusts out, the duct of cement is still left. However, if
we are going to the expense of laying in cement, it would be much
preferable to use cement lined pipe, which is not only cheaper than iron
pipe, but makes the most perfect cable conduit, as it affords a
perfectly smooth surface to draw the cable over and give a good duct
edge.

It is not necessary, however, in small installations of cable,
especially where additional connections will not be of frequent
occurrence, to go to the expense of subways, for cable may be safely
laid in the ground in trenches filled in with earth, or can be inclosed
in a plain wooden box or a wooden box filled with pitch.

There are, of course, many localities where, if the cable is laid in
contact with the earth, a chemical action would take place which might
result in the destruction of the cable.

Underground cables are of the following classes: 1. Rubber insulated
cables, insulated with rubber or other homogeneous material. 2. Fibrous
cables, so called from the conductors being covered with some fibrous
material, as cotton or paper, which is saturated with the insulating
material, paraffine, resin oil, or some special compound. Under this
latter head is also included the dry core paper cables.

The first thing to do is to get the cable drawn into the ducts, and on
the proper accomplishment of this depends to a great extent the success
or failure of the whole installation. Probably the ducts have been wired
when the subway was constructed, but if not a wire must be run through
as a means of pulling in the draw rope. There are several kinds of
apparatus for getting a wire through a duct--rods, flexible tapes,
mechanical "creepers," etc.; but probably the best is the sectional rod.
This simply consists of three or four foot lengths of hard wood rods,
having metal tips that screw into each other. A rod is placed in a duct
at a manhole, one screwed to that, both are pushed forward, another one
added and pushed forward, and so on until they extend the entire length
of the duct. Then the wire is attached and the rods are pulled out and
detached one at a time and with the last rod the wire is through. At
least No. 14 galvanized iron or steel wire should be used, for any
smaller size cannot be used a second time, as a rule. In starting to
pull in the draw rope a wire brush should be attached to the wire and to
this again the rope, and when the brush arrives at the distant end of
the duct it very likely will bring with it a miscellaneous collection of
material which for the good of the cable had better be in the manhole
than in the duct.

The reel or drum carrying the cable should be mounted on wheels or jacks
and placed on the same side of the manhole as the duct into which the
cable is to be drawn, and must always be so placed that the cable will
run off the top of the reel.

There are several methods of attaching the draw rope to the cable. As
simple and strong a method as any is to punch two of these holes through
the cable, lead and all, and attach the rope by means of an iron
wire--some of the draw wire will do--run through these holes. Depending
on the length and weight of cable to be pulled it can be drawn either by
hand or by a multiplying winch. The rope should run through a block
fastened in the manhole in such a position that the rope shall have a
good straightaway lead from the mouth of the duct.

The strain on the cable should be perfectly uniform and steady; if the
power is applied by a series of jerks either the lead covering may be
pulled apart or some of the conductors broken. At the reel there must
always be a large enough number of men to turn it and keep the cable
from rubbing on anything, and in the manhole one or more men to see that
the cable feeds into the duct straight and to guide it if necessary. If
the ducts are of iron and are not perfectly smooth at the ends, these
should be made so with a file, and in addition a protector of some sort
should be placed in the mouths of the duct, both above and below the
cable. Six inches of lead pipe, split lengthwise and bent over at one
end to prevent being drawn into the duct with the cable, makes a very
good protector. The cable should be reeled off the drum just fast enough
to prevent any of the power used in pulling the cable through the duct
being utilized in unreeling it. If this latter is allowed to occur the
cable will be bent too short and the lead covering buckled or broken,
and also the cable may be jammed against the upper edge of the duct and
perhaps cut through.

If the reel is allowed to turn faster than the cable is drawn in, the
first three or four turns on the reel will slacken up, and the lead
covering may either be dented or cut through by scraping on the ground.
If the cable end when pulled through up to the block is not long enough
to bend around the hole more than half way, the rope should be
unfastened from its end, a length of rope with a well frayed out end
should be run through the block, and by fastening to the cable close to
the duct, with a series of half hitches, as much slack as necessary can
be pulled in. If this is properly manipulated there need not be a
scratch on the cable, but unless great care is taken the lead may be
pressed up into ridges and the core itself damaged.

Immediately after the cable is drawn in, if the joint is not to be at
once made, the open end or ends should be cut off and the cable soldered
up, as most cables are very susceptible to moisture and readily absorb
water even from the atmosphere. Where practicable it is always a good
plan to pull the cable through as many manholes as possible without
cutting the cable; for the joint is, especially in telephone or
telegraph cables, the weak point. To do this the rope should be pulled
through the proper duct in the next section without unfastening it from
the cable; the winch should be moved to the next manhole, and pulling
through then done as before. There should always be a man in every hole
through which the cable is running to see that it does not bind anywhere
and to keep protectors around the cable.

It is not advisable to pull more than one cable into a duct, and never
advisable to pull a cable into a duct containing another cable, but if
two or more cables have to go into the same duct, they should always be
drawn in together. Lead covered cables and those with no lead on the
outside should never be pulled into the same duct, for if they bind
anywhere the soft cable will suffer where two lead covered cables would
get through all right. Some manufacturers are now putting on their
cables a tape or braid covering, which saves the lead many bad bruises
and cuts, and is a valuable addition to a cable at very little
additional expense.

Practically all electric light and power cables are either single or
double conductors, and the jointing of these is comparatively a simple
matter, although requiring considerable care. The lead is cut back from
each end about four or five inches, and the conductors bared of
insulation for two or three inches. The bare conductors should be
thoroughly tinned by dipping in the metal pot or pouring the melted
solder over them. A sperm candle is better than resin or acid for any
part of the operations where solder is used. A lead sleeve is here
slipped back over the cable, out of the way, and the ends of the
conductors brought together in a copper sleeve which is then sweated to
a firm joint. This part must be as good a piece of work mechanically as
electrically. The bare splice is then wrapped tightly with cotton or
silk tape to a thickness slightly greater than that of the insulation of
the cable, and is thoroughly saturated with the insulating compound
until all moisture previously absorbed by the tape is driven off.

The lead sleeve is then brought over the splice and wiped to the cable.
The joint is then filled with the insulating compound poured through
holes in the top of the sleeve; these holes are then closed and the
joint is complete, and there is no reason why, in light and power
cables, that joint should not be as perfect as any other part of the
cable. When the cable ends are prepared for jointing they should be hung
up in such a position that they are in the same plane, both horizontal
and vertically, and firmly secured there, so that when the lead sleeve
is wiped on the conductor may be in its exact center, and great care
must be taken not to move the cables again until the sleeve is filled
and the insulation sufficiently cooled to hold the conductor in
position.

It is also very important to see that there are no sharp points on the
conductors themselves, on the copper sleeve, on the edges of the lead
covering or on the lead sleeve. All these should be made perfectly
smooth, for points facilitate disruptive discharges. Branch joints had
better be made as T-joints rather than as Y-joints, for they are better
electrically and mechanically, although they occupy more room in the
manholes. They are of course made in the same way as straight joints, a
lead T-sleeve being used, however. For multiple arc circuits copper
T-sleeves and for series circuits copper L-sleeves are used.

Telephone and telegraph cables are made of any required gauge of wire
and with from 1 to 150 conductors in a cable. In jointing these the
splices are never soldered, the conductors being joined either with a
twist joint or with the so-called Western Union splice. Each splice is
covered with a cotton or silk sleeve or a wrapping of tape, the latter
being preferable, although considerably increasing the time necessary
for making the joint. Great care must be taken that no ends of wire are
left sticking up, for they will surely work their way through the tape
and grounds, and crosses will be the result. The wires should always be
joined layer to layer and each splice very tightly taped in order to get
as much insulating compound around each splice as possible in the
limited space. The splices should be "broken" as much as possible, so as
to avoid having adjoining splices coming over each other. After the
joint has been saturated with insulating compound the wires should have
an outside wrapping of tape to keep them in shape, and then the sleeve
is wiped on and filled. If the insulation resistance of the jointed
telegraph or telephone cable is a quarter of what the cable tested in
the factory, it may be considered that an exceptionally good piece of
work has been done. I have spoken more particularly of fibrous lead
covered cables, as the handling of them includes practically every step
of the work on any other kind of underground cable. In insulating dry
core paper cables a paper sleeve is slipped over the splice, and in
rubber cables the splice is wrapped with rubber tape; all other details
are the same for these as for the fibrous cable.

In the laying of light and power cables every joint, as made, should be
tested for insulation with a Thomson galvanometer, as the insulation
must necessarily be very high, and if one joint or section of cable is
any weaker than another it may be very important in the future to know
it. All tests must be made after the joint has cooled, for while hot its
insulation resistance will be very low.

Tests for copper resistance should also be made to determine if the
splices are electrically perfect; an imperfect splice may cause
considerable trouble. In telegraph and telephone cables the conductors
should be of very soft copper, for in stripping the conductor of
insulation it is very easy to nick the wire, and if of hard drawn copper
open wires will be the result.

All work should be frequently tested for continuity with telephones,
magnetos, or small portable galvanometers. It is only necessary to
ground the conductors at one end and try each wire at the other end. For
this sort of work a telephone receiver used with one cell of some dry
battery is most convenient, and has the additional advantage of
affording a means of communication while testing, and is by far the best
thing for identifying and tagging conductors.

These cables should be frequently tested during the progress of the work
for grounds and crosses with a Thomson instrument, and when the cable is
complete, a careful series of tests of the capacity, insulation
resistance, and copper resistance of each wire should be made and the
exact condition of the cable determined before it is put in service, and
thereafter an intelligent oversight of the condition of the circuits
can thus be more readily maintained.

Where a company has extensive underground service, a regular cable gang
should be in its employ, for quick and safe handling of cables demands
the employment of men accustomed to the work. If the cable has been
properly laid and tests show it to be in good condition before current
is turned on, almost the only trouble to be anticipated will be due to
mechanical injury. Disruptive discharge, puncturing the lead, may occur;
but the small chance of its occurring can be greatly lessened by the use
of some kind of "cable protector," which will provide for the spark an
artificial path of less resistance than the dielectric of the condenser,
which the cable in fact becomes.

If a fault suddenly develops on a circuit, the chances are it will be
found in a manhole, and an inspection of the cable in the manhole will
generally reveal the trouble without resorting to locating with a
Wheatstone bridge. The cable is often cut through at the edge of the
duct, or damaged by something falling on it, or by some one "walking all
over it." To guard against these, the ducts should always be fitted with
protectors both above and below the cable. The cables should never be
left across the manholes, for they then answer the purpose of a ladder,
but should be bent, around the walls of the hole and securely fastened
with lead straps, that they may not be moved and the lead gradually worn
through.

In telegraph cables, when one or two conductors "go," it will probably
be useless to look for trouble except with instruments; but if several
wires are "lost" at once it will probably be found to be caused by
mechanical injury, which can be located by inspection. If it is ever
necessary to loop out conductors, a joint can be readily opened and the
conductors wanted picked out and connected into the branch cable and the
joint again closed without disturbing the working wires. In doing this a
split sleeve must be used, and the only additional precaution to be
taken is in filling the sleeve to have the insulating compound not hot
enough to melt the solder and open up the split in the sleeve. In
cutting in service on light and power cables it is entirely practicable
to do so without interruption of service on multiple arc circuits, even
those of very high voltage; but they require great precaution and
involve considerable risk to the jointer, and where possible the circuit
to which the connection is to be made should previously be cut dead.
Where the voltage is not dangerous to human life, almost any service
connection can be made without interruption of service.

I have only indicated a very few of the operations that may be found
necessary, and the probable causes of troubles that may be encountered
in the operating of underground circuits, believing that the different
problems that arise can, with a little experience, be successfully met
by any one who has a fair knowledge of the original construction of
cable lines.--_Electrical World_.

       *       *       *       *       *




RAILROADS TO THE CLOUDS.


If George Stephenson, when he placed the first locomotive on the track
and guaranteed it a speed of six miles an hour, could have foreseen that
in less than eighty years the successors of his rude machine would be
climbing the sides of mountain ranges, piercing gorges hitherto deemed
inaccessible, crossing ravines on bridges higher than the dome of St.
Paul's, and traversing the bowels of the earth by means of tunnels, no
doubt his big blue eyes would have stood out with wonder and amazement.
But he foresaw nothing of the kind; the only problem present in his mind
was how to get goods from the seaports in western England to London as
easily and cheaply as possible, and to do this he substituted for
horses, which had for 150 years been drawing cars along wooden or iron
tracks, the wonderful machine which has revolutionized the freight and
passenger traffic of the world.

It was, indeed, impossible for any one to foresee the triumphs of
engineering which have accompanied the advances in transportation. To
the engineer of the present day there are no impossibilities. The
engineer is a wizard at whose command space and matter are annihilated.
The highest mountain, the deepest valley, has no terrors for him. He can
bridge the latter and encircle or tunnel the former. The only requisites
which he demands are that something in his line be needed, and that the
money is forthcoming to defray the expense, and the thing will be done.
But the railroad he is asked to construct must be necessary, and the
necessity must be plainly shown, or no funds will be advanced; and
although the theory does not invariably hold good, especially when a
craze for railroad building is raging, as a rule no expense for the
construction of a road will be incurred without a prospect of
remuneration.

Hence the need of railroad communication has caused lines to be
constructed through districts where only a few years ago the thing would
have been deemed impossible. The Pacific roads of this country were a
necessity long before their construction, and in the face of
difficulties almost insuperable were carried to successful completion.
So, also, of the railroads in the Andes of South America. The famous
road from Callao through the heart of Peru is one of the highest
mountain roads in the world, as well as of the most difficult
construction. The grades are often of 300 feet and more to the mile, and
when the mountains were reached so great were the difficulties the
engineers were forced to confront that in some places laborers were
lowered from cliffs by ropes in order that, with toil and difficulty,
they might carve a foothold in order to begin the cutting for the
roadway.

In some sections tunnels are more numerous than open cuts, and so far as
the road has gone sixty-one tunnels, great and small, have been
constructed, aggregating over 20,000 feet in length. The road attains a
height of 15,000 feet above the level of the sea, and at the highest
point of the track is about as high as the topmost peak of Mont Blanc.
It pierces the range above it by a tunnel 3,847 feet long. The stern
necessities of business compelled the construction of this road,
otherwise it never would have been begun.

The tunnels of the Andes, however, do not bear comparison with the
tunnels, bridges, and snow sheds of the Union Pacific, nor do even these
compare with the vast undertakings in the Alps--three great tunnels of
nine to eleven miles in length, which have been prepared for the
transit of travelers and freight. The requirements of business
necessitated the piercing of the Alps, and as soon as the necessity was
shown, funds in abundance were forthcoming for the enterprise.

But tunneling a mountain is a different thing from climbing it. Many
years ago the attention of inventors was directed to the practicability
of constructing a railroad up the side of a mountain on grades which, to
an ordinary engine, were quite impossible. The improvements in
locomotives twenty-five and thirty years ago rendered them capable of
climbing grades which, in the early days of railroad engineering, were
deemed out of the question. The improvements proved a serious stumbling
block in the way of the inventors, who found that an ordinary locomotive
was able to climb a much steeper grade than was commonly supposed. The
first railroads were laid almost level, but it was soon discovered that
a grade of a few feet to the mile was no impediment to progress, and
gradually the grade was steepened.

The inventors of mountain railroad transportation might have been
discouraged by this discovery, but it is a characteristic of an inventor
that he is not set back by opposition, which, in fact, only serves to
stimulate his zeal. The projectors of inclined roads and mountain
engines kept steadily on, and in France, Germany, England, and the
United States many experimental roads were constructed, each of a few
hundred yards in length, and locomotive models were built and put in
motion to the amazement of the general public, who jeered alike at the
contrivances and the contrivers, deeming the former impracticable and
the latter crazy.

But the idea of building a road up the side of a hill was not to be
dismissed. There was money in it for the successful man, so the cranky
inventors kept on at work in spite of the jeers of the rabble and the
discouragements of capitalists loath to invest their money in an
uncertain scheme. To the energy and perseverance of railroad inventors
the success of the mountain railroad is due, as also is the construction
of the various mountain roads, of which the road up Mt. Washington,
finished in 1868, was the first, and the road up Pike's Peak, completed
the other day, was the latest.

Of all the mountain roads which have been constructed since the one up
Mt. Washington was finished, the best known is that which ascends the
world-famous Rigi. With the exception of Mont Blanc, Rigi is, perhaps,
the best known of any peak in the Alps, though it is by no means the
highest, its summit being but 5,905 feet above the level of the sea.
Although scarcely more than a third of the height of some other
mountains in the Alps, it seems much higher because of its isolated
position. Standing as it does between lakes Lucerne, Zug, and Lowertz,
it commands a series of fine views in every direction, and he who looks
from the summit of Rigi, if he does no other traveling in Switzerland,
can gain a fair idea of the Swiss mountain scenery. Many of the most
noted peaks are in sight, and from the Rigi can be seen the three lakes
beneath, the villages which here and there dot the shores, and, further
on, the mighty Alps, with their glaciers and eternal snows.

Many years ago a hotel was built on the summit of the Rigi for the
benefit of the tourists who daily flocked to this remarkable peak to
enjoy the benefit of its wonderful scenery. The mountain is densely
wooded save where the trees have been cut away to clear the land for
pastures. The ease of its ascent by the six or eight mule paths which
had been made, the gradual and almost regular slope, and the throngs of
travelers who resorted to it, made it a favorable place for an
experiment, and to Rigi went the engineers in order to ascertain the
practicability of such a road. The credit of the designs is due to a
German engineer named Regenbach, who, about the year 1861, designed the
idea of a mountain road, and drew up plans not only for the bed but also
for the engine and cars. The scheme dragged. Capitalists were slow to
invest their money in what they deemed a wild and impracticable
undertaking, and even the owners of the land on the Rigi were reluctant
for such an experiment to be tried. But Regenbach persevered, and toward
the close of the decade the inhabitants of Vitznau, at the base of the
Rigi, were astonished to see gangs of laborers begin the work of making
a clearing through the forests on the mountain slope. They inquired what
it meant, and were told that a road up the Rigi was to be made. The
Vitznauers were delighted, for they had no roads, and there was not a
wheeled vehicle in the town, nor a highway by which it could be brought
thither. The idea of a railroad in their desolate mountain region, and,
above all, a railroad up the Rigi, never entered their heads, and a
report which some time after obtained currency in the town, that the
laborers were beginning the construction of a railroad, was greeted with
a shout of derision.

Nevertheless, that was the beginning of the Rigi line, and in May, 1871,
the road was opened for traffic. It begins at Vitznau, on Lake Lucerne,
and extends to the border of the canton and almost to the top of the
mountain. It is 19,000 feet long, and during that distance rises 4,000
feet at an average grade of 1 foot in 4. Though steep, it is by no means
so much so as the Mt. Washington road, which rises 5,285 feet above the
sea, at an average of 1 foot in 3. There are, however, stretches of the
Rigi road at which the grade is about 1 foot in 2½, which is believed to
be the steepest in the world.

The Rigi road has several special features aside from its terrific
slopes which entitle it to be considered a triumph of the engineer's
skill. About midway up the mountains the builders came to a solid mass
of rock, which presented a barrier that to a surface road was
impassable. They determined to tunnel it, and, after an enormous
expenditure of labor, finished an inclined tunnel 225 feet in length, of
the same gradient as the road. A gorge in the side of the mountain where
a small stream, the Schnurtobel, had cut itself a passage also hindered
their way, and was crossed by a bridge of lattice girder work in three
spans, each 85 feet long. The entire roadbed, from beginning to end, was
cut in the solid rock. A channel was chiseled out to admit the central
beam, which contains the cogs fitting the driving wheel of the
locomotive. The engine is in the rear of the train, and presents the
exceedingly curious feature of a boiler greatly inclined, in order that
at the steeper gradients it may remain almost perpendicular. The coal
and water are contained in boxes over the driving wheels, so that all
the weight of the engine is really concentrated on the cogs--a
precaution to prevent their slipping. The cost of the road, including
three of these strangely constructed locomotives, three passenger
coaches, and three open wagons, was $260,000, and it is a good paying
investment. The fare demanded for the trip up the mountains is 5 francs,
while half that sum is required for the downward passage, and the road
is annually traversed by from 30,000 to 50,000 passengers.

Curious sensations are produced by a ride up this remarkable line. The
seats of the cars are inclined like the boiler of the locomotive, and so
long as the cars are on a level the seats tilt at an angle which renders
it almost impossible to use them. But when the start is made the
frightful tilt places the body in an upright position, and, with the
engine in the rear, the train starts up the hill with an easy, gliding
motion, passing up the ascent, somewhat steeper than the roof of a
house, without the slightest apparent effort. But if the going up
excites tremor, much more peculiar are the feelings aroused on the down
grade. The trip begins with a gentle descent, and all at once the
traveler looking ahead sees the road apparently come an end. On a nearer
approach he is undeceived and observes before him a long decline which
appears too steep even to walk down. Involuntarily he catches at the
seats, expecting a great acceleration of speed. Very nervous are his
feelings as the train approaches this terrible slope, but on coming to
the incline the engine dips and goes on not a whit faster than before
and not more rapidly on the down than on the up grade. Many people are
made sick by the sensation of falling experienced on the down run. Some
faint, and a few years ago one traveler, supposed to be afflicted with
heart disease, died of fright when the train was going over the
Schnurtobel bridge. The danger is really very slight, there not having
been a serious accident since the road was opened. The attendants are
watchful, the brakes are strong, but even with all these safeguards, men
of the steadiest nerves cannot help wondering what would become of them
in case anything went wrong.

Bold as was the project of a railroad on the Rigi, a still bolder scheme
was broached ten years later, when a daring genius proposed a railroad
up Mt. Vesuvius. A railroad up the side of an ordinary mountain seemed
hazardous enough, but to build a line on the slope of a volcano, which
in its eruption had buried cities, and every few years was subject to a
violent spasm, seemed as hazardous as to trust the rails of an ordinary
line to the rotten river ice in spring time. The proposal was not,
however, so impracticable as it looked. While the summit of Vesuvius
changes from time to time from the frequent eruptions, and varies in
height and in the size of the crater, the general slope and contour of
the mountain are about the same to-day as when Vesuvius, a wooded hill,
with a valley and lake in the center of its quiescent crater, served as
the stronghold of Spartacus and his rebel gladiators. There have been
scores of eruptions since that in which Herculaneum and Pompeii were
overthrown, but the sides of the mountain have never been seriously
disturbed.

A road on Vesuvius gave promise of being a good speculation. Naples and
the other resorts of the neighborhood annually attracted many thousands
of visitors, and a considerable number of these every year ascended the
volcano, even when forced to contend with all the difficulties of the
way. Many, however, desiring to ascend, but being unable or unwilling to
walk up, a chair service was established--a peculiar chair being slung
on poles and borne by porters. In course of time the chair service
proved to be inadequate for the numbers who desired to make the ascent,
and the time was deemed fit for the establishment of more speedy
communication.

Notwithstanding the necessity, the proposal to establish a railroad met
with general derision, but the scheme was soon shown to be perfectly
practicable, and a beginning was made in 1879. The road is what is known
as a cable road, there being a single sleeper with three rails, one on
the top which really bore the weight, and one on each side near the
bottom, which supported the wheels, which coming out from the axle at a
sharp angle, prevented the vehicle from being overturned. The road
covers the last 4,000 feet of the ascent, and the power house is at the
bottom, a steel cable running up, passing round a wheel at the top and
returning to the engine in the power house. The ascent to the lower
terminus of the road is made on mules or donkeys; then, in a comfortable
car, the traveler is carried to a point not far from the crater. The car
is a combined grip and a passenger car, similar in some points to the
grip car of the present day, while the seats of the passenger portion
are inclined as in the cars on the Rigi road. But the angle of the road
being from thirty-three to forty-five degrees, makes both ascent and
descent seem fearfully perilous. Every precaution, however, is taken to
insure the safety of passengers; each car is provided with several
strong and independent brakes, and thus far no accident worth recording
has occurred. The road was opened in June, 1880. Although there have
been several considerable eruptions since that date, none of them did
any damage to the line but what was repaired in a few hours.

The fashion thus set will, no doubt, be followed in many other quarters.
Wherever there is sufficient travel to pay working expenses and a profit
on a steep grade mountain road it will probably be built. Already there
is talk of a road on Mont Blanc, of another up the Yungfrau, and several
have been projected in the Schwartz and Hartz mountains. A route on Ben
Nevis, in Scotland, is already surveyed, and it is said surveys have
also been made up Snowden, with a view to the establishment of a road to
the summit of the highest Welsh peak. Sufficient travel is all that is
necessary, and when that is guaranteed, whenever a mountain possesses
sufficient interest to induce people to make its ascent in considerable
numbers, means of transportation, safe and speedy, will soon be
provided. The modern engineer is able, willing and ready to build a road
to the top of Mt. Everest in the Himalayas if he is paid for doing
so.--_St. Louis Globe-Democrat._

       *       *       *       *       *

To clean hair brushes, wash with weak solution of washing soda, rinse
out all the soda, and expose to sun.

       *       *       *       *       *




THE MARCEAU.


[Illustration: THE FRENCH ARMORED TURRET SHIP MARCEAU]

The Marceau, the last ironclad completed and added to the French navy,
was put in commission at Toulon in April last, and has lately left that
town to join the French squadron of the north at Brest. The original
designs of this ship were prepared by M. Huin, of the French Department
of Naval Construction, but since the laying down of the keel in the year
1882 they have been very considerably modified, and many improvements
have been introduced.

Both ship and engines were constructed by the celebrated French firm,
the Société des Forges et Chantiers de la Mediterranée, the former at
their shipyard in La Seyne and the latter at their engine works in
Marseilles. The ship was five years in construction on the stocks, was
launched in May, 1887, and not having been put in commission until the
present year, was thus nearly nine years in construction. She is a
barbette belted ship of somewhat similar design to the French ironclads
Magenta, now being completed at the Toulon arsenal, and the Neptune, in
construction at Brest.

The hull is constructed partly of steel and partly of iron, and has the
principal dimensions as follows. Length, 330 ft. at the water line;
beam, 66 ft. outside the armor; draught, 27 ft. 6 in. aft.;
displacement, 10,430 English or 10,600 French tons. The engines are two
in number, one driving each propeller; they are of the vertical compound
type, and on the speed trials developed 11,300 indicated horse power
under forced and 5,500 indicated horse power under natural draught, the
former giving a speed of 16.2 knots per hour with 90 revolutions per
minute. The boilers are eight in number, of the cylindrical marine type,
and work at a pressure of 85.3 lb. per square inch. During the trials
the steering powers of the ship were found to be excellent, but the bow
wave is said, by one critic, to have been very great.

The ship is completely belted with Creusot steel armor, which varies in
thickness from 9 in. forward to 17¾ in. midships. In addition to this
belt the ship is protected by an armored deck of 3½ in., while the
barbette gun towers are protected with 15¾ in. steel armor with a hood
of 2½ in. to protect the men against machine gun fire. As a further
means of insuring the life of the ship in combat and also against
accidents at sea, the Marceau is divided into 102 water-tight
compartments and is fitted with torpedo defense netting. There are two
masts, each carrying double military tops; and a conning tower is
mounted on each mast, from either of which the ship may be worked in
time of action, and both of which are in telegraphic communication with
the engine rooms and magazines. Provision is made for carrying 600 tons
of coal, which, at a speed of 10 knots, should be sufficient to supply
the boilers for a voyage of 4,000 miles.

The armament of the Marceau is good for the tonnage of the ship and
consists principally of four guns of 34 centimeters (13.39 in.) of the
French 1884 model, having a weight of 52 tons, a length of 28½ calibers,
and being able to pierce 30 in. of iron armor at the muzzle. The
projectiles weigh 924 lb., and are fired with a charge of 387 lb. of
powder. The muzzle velocity has been calculated to be 1,968 ft. per
second. The guns are entirely of steel and are mounted on Canet
carriages in four barbette towers, one forward, one aft, and one on each
side amidships. On the firing trials both the guns and all the Canet
machinery, for working the guns and hoisting the ammunition, gave very
great satisfaction to all present at the time. In addition to the above
four heavy guns there are, in the broadside battery, sixteen guns of 14
centimeters (5.51 in.), eight on each side, and a gun of equal caliber
is mounted right forward on the same deck. The armament is completed by
a large number of Hotchkiss quick-firing and revolver guns and four
torpedo tubes, one forward, one aft, and one on each side.

The crew of the Marceau has been fixed at 600 men, and the cost is
stated to have been about $3,750,000.--_Engineering_.

       *       *       *       *       *

[Continued from SUPPLEMENT, No. 820, page 13097.]




A REVIEW OF MARINE ENGINEERING DURING THE PAST DECADE.[1]

[Footnote 1: Paper read before the Institution of Mechanical Engineers,
July 28, 1891.]

BY MR. ALFRED BLECHYNDEN, OF BARROW-IN-FURNESS


_Steam Pipes_.--The failures of copper steam pipes on board the Elbe,
Lahn, and other vessels have drawn serious attention both to the
material and to the modes of construction of the pipes. The want of
elastic strength in copper is an important element in the matter; and
the three following remedies have been proposed, while still retaining
copper as the material. First, in view of the fact that in the operation
of brazing the copper may be seriously injured, to use solid drawn
tubes. This appears fairly to meet the main dangers incidental to
brazing; but as solid drawn pipes of over 7 inches diameter are
difficult to procure, it hardly meets the case sufficiently. Secondly,
to use electrically deposited tubes. At first much was promised in this
direction; but up to the present time it can hardly be regarded as more
than in the experimental stage. Thirdly, to use the ordinary brazed or
solid drawn tubes, and to re-enforce them by serving with steel cord or
steel or copper wire. This has been tried, and found to answer
perfectly. For economical reasons, as well as for insuring the minimum
of torsion to the material during manufacture, it is important to make
as few bends as possible; but in practice much less difficulty has been
experienced in serving bent pipes in a machine than would have been
expected. Discarding copper, it has been proposed to substitute steel or
iron. In the early days of the higher pressures, Mr. Alexander Taylor
adopted wrought iron for steam pipes. One fitted in the Claremont in
February, 1882, was recently removed from the vessel for experimental
purposes, and was reported upon by Mr. Magnus Sandison in a paper read
before the Northeast Coast Institution of Engineers and Shipbuilders.[2]
The following is a summary of the facts. The pipe was 5 inches external
diameter, and 0.375 inch thick. It was lap welded in the works of
Messrs. A. & J. Stewart. The flanges were screwed on and brazed
externally. The pipe was not lagged or protected in any manner. After
eight and a half years' service the metal measured where cut 0.32 and
0.375 inch in thickness, showing that the wasting during that time had
been very slight. The interior surface of the tube exhibited no signs of
pitting or corrosion. It was covered by a thin crust of black oxide, the
maximum thickness of which did not exceed 1/32 inch. Where the deposit
was thickest it was curiously striated by the action of the steam. On
the scale being removed, the original bloom on the surface of the metal
was exposed. It would thus appear that the danger from corrosion of iron
steam pipes is not borne out in their actual use; and hence so much of
the way is cleared for a stronger and more reliable material than
copper. So far the source of danger seems to be in the weld, which would
be inadmissible in larger pipes; but there is no reason why these should
not be lapped and riveted. There seems, however, a more promising way
out of the difficulty in the Mannesmann steel tubes which are now being
"spun" out of solid bars, so as to form weldless tubes.

[Footnote 2: Transactions Northeast Coast Institution of Engineers and
Shipbuilders, vol. 7, 1890-91, p. 179.]

TABLE I.--TENSILE STRENGTH OF GUN METAL AT HIGH TEMPERATURES.

--------------+------------+-------------+-------------+------------+
              |            |             |             |            |
 Composition  |Temperature |   Tensile   |   Elastic   | Elongation |
     of       |  of oil    |   strength  |    limit    |     in     |
 gun metal.   |   bath.    |  per square |  per square | length of  |
              |            |    inch.    |    inch.    | 2 inches   |
--------------+------------+-------------+-------------+------------+
   Per cent.  |    Fahr.   |    Tons     |    Tons     |  Per cent. |
 Copper 87   /|     50°    |    12.34    |     8.38    |    14.64   |
 Tin     8  / |            |             |             |            |
 Zinc    3½ \ |            |             |             |            |
 Lead    1½  \|    400°    |    10.83    |     6.30    |    11.79   |
--------------+------------+-------------+-------------+------------+
 Copper 87   /|     50°    |    13.86    |     8.33    |    20.30   |
 Tin     8  { |            |             |             |            |
 Zinc    5   \|    458°    |    10.70    |     7.43    |    12.42   |
--------------+------------+-------------+-------------+------------+

Cast steel has been freely used by the writer for bends, junction
pieces, etc., of steam pipes, as well as for steam valve chests; and
except for the fact that steel makers' promises of delivery are
generally better than their performance, the result has thus far been
satisfactory in all respects. These were adopted because there existed
some doubt as to the strength of gun metal under a high temperature; and
as the data respecting its strength appeared of a doubtful character, a
series of careful tests were made to determine the tensile strength of
gun metal when at atmospheric and higher temperatures. The test bars
were all 0.75 in diameter, or 0.4417 square inch sectional area; and
those tested at the higher temperatures were broken while immersed in a
bath of oil at the temperature here stated, each line being the mean of
four experiments. The result of these experiments was to give somewhat
greater faith in gun metal as a material to be used under a higher
temperature; but as steel is much stronger, it is probably the most
advisable material to use, when the time necessary to procure it can be
allowed.

_Feed Heating_.--With the double object of obviating strain on the
boiler through the introduction of the feed water at a low temperature,
and also of securing a greater economy of fuel, the principle of
previously heating the feed water by auxiliary means has received
considerable attention, and the ingenious method introduced by Mr. James
Weir has been widely adopted. It is founded on the fact that, if the
feed water as it is drawn from the hot well be raised in temperature by
the heat of a portion of steam introduced into it from one of the steam
receivers, the decrease of the coal necessary to generate steam from the
water of the higher temperature bears a greater ratio to the coal
required without feed heating than the power which would be developed in
the cylinder by that portion of steam would bear to the whole power
developed when passing all the steam through all the cylinders. The
temperature of the feed is of course limited by the temperature of the
steam in the receiver from which the supply for heating is drawn.
Supposing, for example, a triple expansion engine were working under the
following conditions without feed heating: Boiler pressure, 150
lb.;--indicated horse power in high pressure cylinder 398, in
intermediate and low pressure cylinders together 790, total, 1,188; and
temperature of hot well 100° Fahr. Then with feed heating the same
engine might work as follows: The feed might be heated to 220° Fahr.,
and the percentage of steam from the first receiver required to heat it
would be 12.2 per cent.; the indicated horse power in the high pressure
cylinder would be as before 398, and in the intermediate and low
pressure cylinders it would be 12.2 per cent, less than before, or 694,
and the total would be 1,092, or 92 per cent. of the power developed
without feed heating. Meanwhile the heat to be added to each pound of
the feed water at 220° Fahr. for converting it into steam would be 1,005
units against 1,125 units with feed at 100° Fahr., equivalent to an
expenditure of only 89.4 per cent. of the heat required without feed
heating. Hence the expenditure of heat in relation to power would be
89.4 + 92.0 = 97.2 per cent., equivalent to a heat economy of 2.8 per
cent. If the steam for heating can be taken from the low pressure
receiver, the economy is about doubled. Other feed heaters, more or less
upon the same principle, have been introduced. Also others which heat
the feed in a series of pipes within the boiler, so that it is
introduced into the water in the boiler practically at boiling
temperature; this is economical, however, only in the sense that wear
and tear of the boiler is saved; in principle the plan does not involve
economy of fuel.

_Auxiliary Supply of Fresh Water_.--Intimately associated with the feed
is the means adopted for making up the losses of fresh water due to
leakage of steam from safety valves, glands, joints, etc., and of water
discharged from the air pumps. A few years ago this loss was regularly
made up from the sea, with the result that the water in the boilers was
gradually increased in density; whence followed deposit on the internal
surfaces, and consequent loss of efficiency, and danger of accident
through overheating the plates. With the higher pressures now adopted,
the danger arising from overheating is much more serious, and the
necessity is absolute of maintaining the heating surfaces free from
deposit. This can be done only by filling the boiler with fresh water in
the first instance, and maintaining it in that condition. To do this two
methods are adopted, either separately or in conjunction. Either a
reserve supply of fresh water is carried in tanks or the supplementary
feed is distilled from sea water by special apparatus provided for the
purpose. In the construction of the distilling or evaporating apparatus
advantage has been taken of two important physical facts, namely, that,
if water be heated to a temperature higher than that corresponding with
the pressure on its surface, evaporation will take place; and that the
passage of heat from steam at one side of a plate to water at the other
is very rapid. In practice the distillation is effected by passing
steam, say from the first receiver, through a nest of tubes inside a
still or evaporator, of which the steam space is connected either with
the second receiver or with the condenser. The temperature of the steam
inside the tubes being higher than that of the steam either in the
second receiver or in the condenser, the result is that the water inside
the still is evaporated, and passes with the rest of the steam into the
condenser, where it is condensed, and serves to make up the loss. This
plan localizes the trouble of deposit, and frees it from its dangerous
character, because an evaporator cannot become overheated like a boiler,
even though it be neglected until it salts up solid; and if the same
precautions are taken in working the evaporator which used to be adopted
with low pressure boilers when they were fed with salt water, no serious
trouble should result. When the tubes do become incrusted with deposit,
they can be either withdrawn or exposed, as the apparatus is generally
so arranged; and they can then be cleaned.

_Screw Propeller_.--In Mr. Marshall's paper of 1881 it was said that
"the screw propeller is still to a great extent an unsolved problem."
This was at the time a fairly true remark. It was true the problem had
been made the subject of general theoretical investigation by various
eminent mathematicians, notably by Professor Rankine and Mr. William
Froude, and of special experimental investigation by various engineers.
As examples of the latter may be mentioned the extended series of
investigations in the French vessel Pelican, and the series made by Mr.
Isherwood on a steam launch about 1874. These experiments, however, such
as they were, did little to bring out general facts and to reduce the
subject to a practical analysis. Since the date of Mr. Marshall's paper,
the literature on this subject has grown rapidly, and, has been almost
entirely of a practical character. The screw has been made the subject
of most careful experiments. One of the earliest extensive series of
experiments was made under the writer's direction in 1881, with a large
number of models, the primary object being to determine what value there
was in a few of the various twists which inventive ingenuity can give to
a screw blade. The results led the experimenters to the conclusion that
in free water such twists and curves are valueless as serving to augment
efficiency. The experiments were then carried further with a view to
determine quantitative moduli for the resistance of screws with
different ratios of pitch to diameter, or "pitch ratios," and afterward
with different ratios of surface to the area of the circle described by
the tips of the blades, or "surface ratios." As these results have to
some extent been analyzed and published, no further reference need be
made to them now.

In 1886, Mr. R.E. Froude published in the Transactions of the
Institution of Naval Architects the deductions drawn from an extensive
series of trials made with four models of similar form and equal
diameter, but having different pitch ratios. Mr. S.W. Barnaby has
published some of the results of experiments made under the direction of
Mr. J.I. Thornycroft; and in his paper read before the Institution of
Civil Engineers in 1890 he has also put Mr. R.E. Froude's results into a
shape more suitable for comparison with practice. Nor ought Mr. G.A.
Calvert's carefully planned experiments to pass unnoticed, of which an
account was given in the Transactions of the Institution of Naval
Architects in 1887. These experiments were made on rectangular bodies
with sections of propeller blade form, moved through the water at
various velocities in straight lines, in directions oblique to their
plane faces; and from their results an estimate was formed of the
resistance of a screw.

One of the most important results deduced from experiments on model
screws is that they appear to have practically equal efficiencies
throughout a wide range both in pitch ratio and in surface ratio; so
that great latitude is left to the designer in regard to the form of the
propeller. Another important feature is that, although these experiments
are not a direct guide to the selection of the most efficient propeller
for a particular ship, they supply the means of analyzing the
performances of screws fitted to vessels, and of thus indirectly
determining what are likely to be the best dimensions of screw for a
vessel of a class whose results are known. Thus a great advance has been
made on the old method of trial upon the ship itself, which was the
origin of almost every conceivable erroneous view respecting the screw
propeller. The fact was lost sight of that any modification in form,
dimensions, or proportions referred only to that particular combination
of ship and propeller, or to one similar thereto; so something like
chaos was the result. This, however, need not be the case much longer.

In regard to the materials used for propellers, steel has been largely
adopted for both solid and loose-bladed screws; but unless protected in
some way, the tips of the blades are apt to corrode rapidly and become
unserviceable. One of the stronger kinds of bronze is often judiciously
employed for the blades, in conjunction with a steel boss. Where the
first extra expense can be afforded, bronze seems the preferable
material; the castings are of a reliable character, and the metal does
not rapidly corrode; the bronze blades can therefore with safety be made
lighter than steel blades, which favors their springing and
accommodating themselves more readily to the various speeds of the
different parts of the wake. This might be expected to result in some
slight increase of efficiency; of which, however, the writer has never
had the opportunity of satisfactorily determining the exact extent.
Instances can be brought forward where bronze blades have been
substituted for steel or iron with markedly improved results; but in
cases of this kind which the writer has had the opportunity of
analyzing, the whole improvement might be accounted for by the modified
proportions of the screw when in working condition. In other words, both
experiment and practical working alike go to show that, although cast
iron and steel blades as usually proportioned are sufficiently stiff to
retain their form while at work, bronze blades, being made much lighter,
are not; and the result is that the measured or set pitch is less than
that which the blades assume while at work. Some facts relative to this
subject have already been given in a recent paper by the author.

_Twin Screws_.--The great question of twin screw propulsion has been put
to the test upon a large scale in the mercantile marine, or rather in
what would usually be termed the passenger service. While engineers,
however, are prepared to admit its advantages so far as greater security
from total breakdown is concerned, there is by no means thorough
agreement as to whether single or twin screws have the greater
propulsive efficiency. What is required to form a sound judgment upon
the whole question is a series of examples of twin and single screw
vessels, each of which is known to be fitted with the most suitable
propeller for the type of vessel and speed; and until this information
is available, little can be said upon the subject with any certainty. So
far the following large passenger steamers, particulars of which are
given in table II., have been fitted with twin screws. It appears t be a
current opinion that the twin screw arrangement necessitates a greater
weight of machinery. This is not necessarily so, however; on the
contrary, the opportunity is offered for reducing the weight of all that
part of the machinery of which the weight relatively to power is
inversely proportional to the revolutions for a given power. This can be
reduced in the proportion of 1 to the square root of 2, that is 71 per
cent. of its weight in the single screw engine; for since approximately
the same total disk area is required in both cases with similar
proportioned propellers, the twins will work at a greater speed of
revolution than the single screw. From a commercial point of view there
ought to be little disagreement as to the advantage of twin screws, so
long as the loss of space incurred by the necessity for double tunnels
is not important; and for the larger passenger vessels now built for
ocean service the disadvantage should not be great. Besides their
superiority in the matter of immunity from total breakdown, and in
greatly diminished weight of machinery, they also offer the opportunity
of reducing to some extent the cost of machinery. A slightly greater
engine room staff is necessary; but this seems of little importance
compared with the foregoing advantages.

TABLE II.--PASSENGER STEAMERS FITTED WITH TWIN SCREWS.

-----------------+-----------+-----+-----------+-------+--------+-------+
                 | Length    |     |     Cylinders,    | Boiler |Indi-  |
                 | between   |     |  two sets in all  |pressure|cated  |
    Vessels.     | perpen-   |Beam.|      cases.       |  per   |horse- |
                 | diculars. |     |-----------+-------| square |power. |
                 |           |     |Diameters. |Stroke.|  inch. |       |
-----------------+-----------+-----+-----------+-------+--------+-------+
                 |   Feet.   |Feet.| Inches.   |Inches.| Lb.    |       |
City of Paris.   |\          |     |           |       |        |       |
                 | }  525    | 63¼ |45, 71, 113|  60   |  150   |20,000 |
City of New York.|/          |     |           |       |        |       |
-----------------+-----------+-----+-----------+-------+--------+-------+
Teutonic.        |\          |     |           |       |        |       |
                 | }  565    | 58  |43, 68, 110|  60   |  180   |18,000 |
Majestic.        |/          |     |           |       |        |       |
-----------------+-----------+-----+-----------+-------+--------+-------+
Normannia.       |    500    | 57½ |40, 67, 106|  66   |  160   |11,500 |
-----------------+-----------+-----+-----------+-------+--------+-------+
Columbia.        |    463½   | 55½ |41, 66, 101|  66   |  160   |12,500 |
-----------------+-----------+-----+-----------+-------+--------+-------+
Empress of India.|\          |     |           |       |        |       |
Empress of Japan.| }  440    | 51  |32, 51, 82 |  54   |  160   |10,125 |
Empress of China.|/          |     |           |       |        |       |
-----------------+-----------+-----+-----------+-------+--------+-------+
Orel.            |    415    | 48  |34, 54, 85 |  51   |  160   |10,000 |
-----------------+-----------+-----+-----------+-------+--------+-------+

_Weight of Machinery Relatively to Power_.--It is interesting to compare
the weight of machinery relatively to the power developed; for this
comparison has sometimes been adopted as the standard of excellence in
design, in respect of economy in the use of material. The principle,
however, on which this has generally been done is open to some
objections. It has been usual to compare the weight directly with the
indicated horse-power, and to express the comparison in pounds per
horse-power. So long as the machinery thus compared is for vessels of
the same class and working at about the same speed of revolution, no
great fault can be found; but as speed of revolution is a great factor
in the development of power, and as it is often dependent on
circumstances altogether external to the engine and concerning rather
the speed of the ship, the engines fitted to high speed ships will thus
generally appear to greater advantage than is their due. Leaving the
condenser out of the question, the weight of an engine would be much
better referred to cylinder capacity and working pressures, where these
are materially different, than directly to the indicated power. The
advantages of saving weight of machinery, so long as it can be done with
efficiency, are well known and acknowledged. If weight is to be reduced,
it must be done by care in design, not by reduction of strength, because
safety and saving of repairs are much more important than the mere
capability of carrying a few tons more of paying load. It must also be
done with economy; but this is a matter which generally settles itself
aright, as no shipowner will pay more for a saving in weight than will
bring in a remunerative interest on his outlay. In his paper on the
weight of machinery in the mercantile marine,[3] Mr. William Boyd
discussed this question at some length, and proposed to attain the end
of reducing the weight of machinery by the legitimate method of
augmenting the speed of revolution and so developing the required power
with smaller engines. This method, while promising, is limited by the
efficiency of the screw, but may be adopted with advantage so long as
the increase in speed of revolution involves no such change in the screw
as to reduce its efficiency as a propeller. But when the point is
reached beyond which a further change involves loss of propelling
efficiency, it is time to stop; and the writer ventures to say that in
many cargo vessels now at work the limit has been reached, while in many
others it has certainly been passed.

[Footnote 3: Transactions Northeast Coast Institution of Engineers and
Shipbuilders, vol. 6, 1889-90, p. 253.]

_Economy of Fuel_.--Coming to the highly important question of economy
of fuel, the average consumption of coal per indicated horse-power is
1.522 lb. per hour. The average working pressure is 158.5 lb. per square
inch. Comparing this working pressure with 77.4 lb. in 1881, a superior
economy of 19 per cent. might be expected now, on account of the higher
pressure, or taking the 1.828 lb. of coal per hour per indicated
horse-power in 1881, the present performance under similar conditions
should be 1.48 lb. per hour per indicated horse-power. It appears that
the working pressures have been increased twice in the last ten years,
and nearly three times in the last nineteen. The coal consumptions have
been reduced 16.7 per cent. in the last ten years and 27.9 per cent. in
the last nineteen. The revolutions per minute have increased in the
ratios of 100, 105, 114; and the piston speeds as 100, 124, 140.
Although it is quite possible that the further investigations of the
Research Committee on Marine Engine Trials may show that the present
actual consumption of coal per indicated horse-power is understated, yet
it is hardly probable that the relative results will be affected
thereby.

_Dimensions_.--In the matter of the power put into individual vessels,
considerable strides have been made. In 1881, probably the greatest
power which has been put into one vessel was in the case of the Arizona,
whose machinery indicated about 6,360 horse-power. The following table
gives an idea of the dimensions and power of the larger machinery in the
later passenger vessels:

TABLE III.--DIMENSIONS AND POWER OF MACHINERY IN LATER PASSENGER
VESSELS.

-----+----------------+-----------------------+-------+-----------+
     |                |                       |Length |           |
Year.| Name of vessel.|     Diameters of      |  of   |Indicated  |
     |                |      cylinders.       |Stroke.|horsepower.|
-----+----------------+-----------------------+-------+-----------+
     |                |        Inches.        |Inches.|           |
1881 |Alaska          |     68, 100, 100      |  72   |   10,686  |
-----+----------------+-----------------------+-------+-----------+
1881 |City of Rome    | 46, 86; 46, 86; 46, 86|  72   |   11,800  |
-----+----------------+-----------------------+-------+-----------+
1881 |Servia          |     72, 100, 100      |  78   |   10,300  |
-----+----------------+-----------------------+-------+-----------+
1881 |Livadia yacht   |  60, 78, 78; 60, 78, \|  39   |   12,500  |
     |                |    78; 60, 78, 78    /|       |           |
-----+----------------+-----------------------+-------+-----------+
1883 |Oregon          |     70, 104, 104      |  72   |   13,300  |
-----+----------------+-----------------------+-------+-----------+
1884 |Umbria          |\    71, 105, 105      |  72   |   14,320  |
1884 |Etruria         |/                      |       |           |
-----+----------------+-----------------------+-------+-----------+
1888 |City of New York|\    45, 71, 113;     \|  60   |   20,000  |
1889 |City of Paris   |/    45, 71, 113      /|       |    about  |
-----+----------------+-----------------------+-------+-----------+
1889 |Majestic        |\    43, 68, 110;     \|  60   |   18,000  |
1889 |Teutonic        |/    43, 68, 110      /|       |           |
-----+----------------+-----------------------+-------+-----------+

In war vessels the increase has been equally marked. In 1881 the maximum
power seems to have been in the Inflexible, namely, 8,485 indicated
horse-power. The following will give an idea of the recent advance made:
Howe (Admiral class), 11,600 indicated horse-power; Italia and Lepanto,
19,000 indicated horse-power; Re Umberto, 19,000 indicated horse-power;
Blake and Blenheim (building), 18,000 indicated horse-power; Sardegna
(building), 22,800 indicated horse-power. It is thus evident that there
are vessels at work to-day having about three times the maximum power of
any before 1881.

_General Conclusions_.--The progress made during the last ten years
having been sketched out, however roughly, the general conclusions may
be stated briefly as follows: First, the working pressure has been about
doubled. Second, the increase of working pressure and other improvements
have brought with them their equivalent in economy of coal, which is
about 20 per cent. Third, marked progress has been made in the direction
of dimension, more than twice the power having been put into individual
vessels. Fourth, substantial advance has been made in the scientific
principles of engineering. It only remains for the writer to thank the
various friends who have so kindly furnished him with data for some of
the tables which have been given; and to express the hope that the next
ten years may be marked by such progress as has been witnessed in the
past. But it must be remembered that, if future progress be equal in
merit or ratio, it may well be less in quantity, because advance becomes
more difficult of achievement as perfection is more nearly approached.

       *       *       *       *       *




THE LITTLE HOUSE.

BY M.M.


One of the highest medical authorities is credited with the statement
that "nine-tenths of the diseases that afflict humanity are caused by
neglect to answer the calls of Nature."

This state of affairs is generally admitted, but is usually attributed
to individual indolence. That, doubtless, has a great deal to do with
it, but should not part of the blame be laid upon the often unpleasant
environments, which make us shrink as from the performance of a painful
duty?

In social life, unless from absolute necessity or charity, people of
refined habits do not call on those whose surroundings shock their sense
of decency; but when they go to pay the calls of Nature, they are often
compelled to visit her in the meanest and most offensive of abodes;
built for her by men's hands; for Nature herself makes no such mistakes
in conducting her operations. She does not always surround herself with
the pomp and pride of life, but she invariably hedges herself in with
the thousand decencies and the pomp of privacy.

But what do we often do? We build what is sometimes aptly termed "an
out-house," because it is placed so that the delicate minded among its
frequenters may be made keenly alive to the fact that they can be
plainly seen by every passer-by and by every idle neighbor on the
lookout. This tiny building is seldom weatherproof; In consequence, keen
cold winds from above, below, and all around find ready entrance, chill
the uncovered person, frequently check the motions, and make the strong
as well as the weak, the young as well as the old, very sorry indeed
that they are so often uselessly obliged to answer the calls of Nature.
It is true, the floor is sometimes carpeted with snow, but the feet feel
that to be but cold comfort, though the door may enjoy rattling its
broken hasp and creaking its loose hinges.

How often, too, are the nose and the eye offended by disregard of the
Mosaic injunction, found in the twelfth, thirteenth, and fourteenth
verses of the twenty-third chapter of Deuteronomy! Of course this
injunction was addressed to a people who had been debased by slavery,
but who were being trained to fit them for their high calling as the
chosen of God; but is not some such sanitary regulation needed in these
times, when a natural office is often made so offensive to us by its
environments that it is difficult for us to believe that "God made man a
little lower than the angels," or that the human body is the temple of
the Holy Ghost?

Dwellers in the aristocratic regions of a well drained city, whose
wealth enables them to surround themselves with all devices tending to a
refined seclusion, may doubt all this, but sanitary inspectors who have
made a round of domiciliary visits in the suburbs, or the older,
neglected parts of a large city, of to any part of a country town or
village, will readily affirm as to its general truth.

This unpardonable neglect of one of the minor decencies by the mass of
the people seems to be caused partly by a feeling of false shame, and
partly by an idea that it is expensive and troublesome to make any
change that will improve their sanitary condition or dignify their daily
lives.

The Rev. Henry Moule, of Fordington Vicarage, Dorsetshire, England, was
one of the first to turn his attention to this matter. With the
threefold object of improving the sanitary condition of his people,
refining their habits, and enriching their gardens, he invented what he
called the "dry earth closet."

"It is based on the power of clay and the decomposed organic matter
found in the soil to absorb and retain all offensive odors and all
fertilizing matters; and it consists, essentially, of a mechanical
contrivance (attached to the ordinary seat) for measuring out and
discharging into the vault or pan below a sufficient quantity of sifted
dry earth to entirely cover the solid ordure and to absorb the urine.

"The discharge of earth is effected by an ordinary pull-up, similar to
that used in the water closet, or (in the self-acting apparatus) by the
rising of the seat when the weight of the person is removed.

"The vault or pan under the seat is so arranged that the accumulation
can be removed at pleasure.

"From the moment when the earth is discharged and the evacuation
covered, all offensive exhalation entirely ceases. Under certain
circumstances there may be, at times, a slight odor as of guano mixed
with earth, but this is so trifling and so local that a commode arranged
on this plan may, without the least annoyance, be kept in use in any
room."

The "dry earth closet" of the philanthropic clergyman was found to work
well, and was acceptable to his parishioners. One reason why it was so
was because dry earth was ready to hand, or could be easily procured in
a country district where labor was cheap. But where labor was dear and
dry earth scarce, those who had to pay for the carting of the earth and
the removal of the deodorized increment found it both expensive and
troublesome.

But a modification of this dry earth closet, the joint contrivance of an
English church clergyman and his brother, "the doctor," residents of a
Canadian country town, who had heard of Moule's invention, is a good
substitute, and is within the reach of all. This will be briefly
described.

The vault was dug as for an ordinary closet, about fifteen feet deep,
and a rough wooden shell fitted in. About four feet below the surface of
this wooden shell a stout wide ledge was firmly fastened all around.
Upon this ledge a substantially made wooden box was placed, just as we
place a well fitting tray into our trunks. About three feet of the back
of the wooden shell was then taken out, leaving the back of the box
exposed. From the center of the back of the box a square was cut out and
a trap door fitted in and hasped down.

The tiny building, on which pains, paint, and inventive genius had not
been spared to make it snug, comfortable, well lighted and well
ventilated, was placed securely on this vault.

After stones had been embedded in the earth at the back of the vault, to
keep it from falling upon the trap door, two or three heavy planks were
laid across the hollow close to the closet. These were first covered
with a barrowful of earth and then with a heap of brushwood.

Within the closet, in the left hand corner, a tall wooden box was
placed, about two-thirds full of dry, well sifted wood ashes. The box
also contained a small long-handled fire shovel. When about six inches
of the ashes had been strewn into the vault the closet was ready for
use. No; not quite; for squares of suitable paper had to be cut, looped
together with twine, and hung within convenient reaching distance of the
right hand; also a little to the left of this pad of paper, and above
the range of sight when seated, a ten pound paper bag of the toughest
texture had to be hung by a loop on a nail driven into the corner.

At first the rector thought that his guests would be "quick-witted
enough to understand the arrangement," but when he found that the
majority of them were, as the Scotch say, "dull in the uptak," he had to
think of some plan to enforce his rules and regulations. As
by-word-of-mouth instructions would have been rather embarrassing to
both sides, he tacked up explicit written orders, which must have
provoked many a smile. Above the bin of sifted ashes he nailed a card
which instructed "Those who use this closet must strew two shovelfuls of
ashes into the vault." Above the pad of clean paper he tacked the
thrifty proverb: "Waste not, want not;" and above the paper bag he
suspended a card bearing this warning: "All refuse paper must be put
into this bag; not a scrap of clean or unclean paper must be thrown into
the vault."

This had the desired effect. Some complacently united to humor their
host's whim, as they called it, and others, immediately recognizing its
utility and decency, took notes with a view to modifying their own
closet arrangements.

Sarah, the maid of all work, caused a good deal of amusement in the
family circle by writing her instructions in blue pencil on the front of
the ash bin. These were: "Strew two shuffefuls of ashes into the volt,
but don't spill two shuffefuls onto the floor. By order of the Gurl who
has to sweap up." This order was emphatically approved of by those
fastidious ones who didn't have to "sweep up."

This closet opened off the woodshed, and besides being snugly
weatherproof in itself, was sheltered on one side by the shed and on
another by a high board fence. The other two sides were screened from
observation by lattice work, outside of which evergreens were planted to
give added seclusion and shade. A ventilator in the roof and two sunny
little windows, screened at will from within by tiny Venetian shutters,
gave ample light and currents of fresh air. For winter use, the rector's
wife and daughters made "hooked" mats for floor and for foot support.
These were hung up every night in the shed to air and put back first
thing in the morning. For the greater protection and comfort of
invalids, an old-fashioned foot warmer, with a handle like a basket, was
always at hand ready to be filled with live coals and carried out.

The little place was always kept as exquisitely clean as the dainty,
old-fashioned drawing room, and so vigilant was the overseeing care
bestowed on every detail, that the most delicate and acute sense of
smell could not detect the slightest abiding unpleasant odor. The paper
bag was frequently changed, and every night the accumulated contents
were burned; out of doors in the summer, and in the kitchen stove--after
a strong draught had been secured--in the winter.

At stated times the deodorized mass of solid increment--in which there
was not or ought not to have been any refuse paper to add useless
bulk--was spaded, through the trap door, out of the box in the upper
part of the vault, into a wheelbarrow, thrown upon the garden soil, and
thoroughly incorporated with it. In this cleansing out process there was
little to offend, so well had the ashes done their concealing
deodorizing work.

In using this modified form of Moule's invention, it is not necessary to
dig a deep vault. The rector, given to forecasting, thought that some
day his property might be bought by those who preferred the old style,
but his brother, the doctor, not troubling about what might be, simply
fitted his well made, four feet deep box, with its trap door, into a
smoothly dug hole that exactly held it, and set the closet over it. In
all other respects it was a model of his brother's.

This last is within the reach of all, even those who live in other
people's houses; for, when they find themselves in possession of an
unspeakably foul closet, they can cover up the old vault and set the
well cleaned, repaired, fumigated closet upon a vault fashioned after
the doctor's plan. A stout drygoods box, which can be bought for a
trifle, answers well for this purpose, after a little "tinkering" to
form a trap door.

Of course, dry earth is by far the best deodorizer and absorbent, but
when it cannot be easily and cheaply procured, well sifted wood or coal
ashes--wood preferred--is a good substitute. The ashes must be kept dry.
If they are not, they lose their absorbing, deodorizing powers. They
must also be well sifted. If they are not, the cinders add a useless and
very heavy bulk to the increment.

An ash sifter can be made by knocking the bottom out of a shallow box,
studding the edge all round with tacks, and using them to cross and
recross with odd lengths of stovepipe wire to form a sieve.--_The
Sanitarian_.

       *       *       *       *       *




THE HYGIENIC TREATMENT OF OBESITY.[1]

[Footnote 1: Translated by Mr. Jos. Helfman, Detroit, Mich.]

BY DR. PAUL CHERON.


In order to properly regulate the regimen of the obese, it is first
necessary to determine the source of the superfluous adipose of the
organism, since either the albuminoids or the hydrocarbons may furnish
fat.

Alimentary fat becomes fixed in the tissues, as has been proved by
Lebede, who fed dogs, emaciated by long fast, with meat wholly deprived
of fat, and substituted for the latter linseed oil, when he was able to
recover the oil in each instance from the animal; parallel experiments
with mutton fat, _in lieu_ of oil, afforded like results.

Hoffman also deprived dogs of fat for a month, causing them to lose as
high as twenty-two pounds weight, then began nourishing with bacon fat
with but little lean; the quantity of fat formed in five days, in the
dog that lost twenty-two pounds, was more than three pounds, which could
have been derived only from the bacon fat.

It has been stated, however, that alimentary fat seems to preserve from
destruction the fat of the organism which arises from other sources. Be
this as it may, it is a fact that the pre-existence of fat furthers the
accumulation of more adipose; or in other words, fat induces fattening!

That adipose may be formed through the transformation of albuminous
matters (meat) is an extremely important corollary, one established
beyond cavil by Pettinkofer and Voit, in an indirect way, by first
estimating the nitrogen and carbon ingested, and second the amount
eliminated. Giving a dog meat that was wholly deprived of fat, they
found it impossible to recover more than a portion of the contained
carbon; hence some must necessarily have been utilized in the organism,
and this would be possible only by the transformation of the carbon into
fat! It goes without saying, however, that the amount of adipose thus
deposited is meager.

Other facts also plead in favor of the transformation of a portion of
albumen into fat within the economy, notably the changing of a portion
of dead organism into what is known as "cadaveric fat," and the very
rapid fatty degeneration of organs that supervenes upon certain forms of
poisoning, as by phosphorus.

The carbohydrates, or more properly speaking hydrocarbons, are regarded
by all physiologists as specially capable of producing fat, and numerous
alimentary experiments have been undertaken to prove this point.
Chaniewski, Meissl, and Munk obtained results that evidenced,
apparently, sugar and starch provide more fat than do the albuminoids.
Voit, however, disapproves this, maintaining the greater part of the
hydrocarbons is burned (furnishes fuel for the immediate evolution of
force), and that fat cannot be stored up unless a due proportion of
albuminoids is also administered. He believes the hydrocarbons exert a
direct influence only; being more oxidizable than fats, they guard the
latter from oxidation. This protective role of the hydrocarbons applies
also to the albuminoids.

We may believe, then, that the three great classes of aliment yield fat,
in some degree; that alimentary fat may be fixed in the tissues; and
that hydrocarbons favor the deposition of adipose either directly or
indirectly.

It is well understood that fat may disappear with great rapidity under
certain conditions; many maladies are accompanied by speedy emaciation;
therefore, as fat never passes into the secretions, at least not in
appreciable quantities, it probably undergoes transformation, perhaps by
oxidation or a form of fermentation, the final results of which are,
directly or indirectly, water and cadaveric acid. It is certain the
process of oxidation favors the destruction of adipose, and that
everything which inhibits such destruction tends to fat accumulation.

Since the earliest period of history, there seems to have been an
anxiety to secure some regimen of general application that would reduce
or combat obesity. Thus Hippocrates says:

Fat people, and all those who would become lean, should perform
laborious tasks while fasting, and eat while still breathless from
fatigue, without rest, and after having drunk diluted wine not very
cold. Their meats should be prepared with sesamum, with sweets, and
other similar substances, and these dishes should be free from fat.

In this manner one will be satiated through eating less.

But, besides, one should take only one meal; take no bath; sleep on a
hard bed; and walk as much as may be.

How much has medical science gained in this direction during the
interval of more than two thousand years? Let us see:

First among moderns to seek to establish on a scientific basis a regimen
for the obese, was Dancel, who forbade fats, starchy foods, etc.,
prescribed soups and aqueous aliment, and reduced the quantity of
beverage to the lowest possible limit; at the same time he employed
frequent and profuse purgation.

This regimen, which permits, at most, but seven to twelve ounces of
fluid at each repast, is somewhat difficult to follow, though it may be
obtained, gradually, with ease. Dr. Constantine Paul records a case in
which this regimen, gradually induced, and followed for ten years,
rewarded the patient with "moderate flesh and most excellent health."

In Great Britain, a mode of treatment instituted in one Banting, by Dr.
Harvey, whereby the former was decreased in weight forty pounds, has
obtained somewhat wide celebrity; and what is more remarkable, it is
known as "Bantingism," taking its name from the patient instead of the
physician who originated it. The dietary is as follows:

_Breakfast_.--Five to six ounces of lean meat, broiled fish, or smoked
bacon--veal and pork interdicted; a cup of tea or coffee without milk or
sugar; one ounce of toast or dry biscuit (crackers).

_Dinner_.--Five or six ounces of lean meat or fish--excluding eel,
salmon, and herring; a small quantity of vegetables, but no potatoes,
parsnips, carrots, beets, peas, or beans; one ounce of toast, fruit, or
fowl; two glasses of red wine--beer, champagne, and port forbidden.

_Tea_.--Two or three ounces of fruit; one kind of pastry; one cup of
tea.

_Supper_.--Three or four ounces of lean beef or fish; one or two glasses
of red wine.

_At bed-time._--Grog without sugar (whisky and water, or rum and water),
and one or two glasses of sherry or Bordeaux.

"Bantingism," to be effective, must be most closely followed, when,
unfortunately also, it proves extremely debilitating; it is suitable
only for sturdy, hard riding gluttons of the Squire Western type. The
patient rapidly loses strength as well as flesh, and speedily acquires
an unconquerable repugnance to the dietary. Further, from a strictly
physiological point of view, the quantity of meat is greatly in excess,
while with the cessation of the regimen, the fat quickly reappears.

Next Ebstein formulated a dietary that is certainly much better
tolerated than that of Harvey and Banting, and yields as good, or even
better, results. He allows patients to take a definite quantity--two to
two and a half ounces-of fat daily, in the form of bacon or butter
which, theoretically at least, offers several advantages: It diminishes
the sensations of hunger and thirst, and plays a special role with
respect to the albuminoids; the latter may thus be assimilated by the
economy without being resolved into fat, and thus the adipose of the
organism at this period is drawn upon without subsequent renewal. The
following is the outline:

_Breakfast_.--At 6 a.m. in summer; 7:30 in winter:--Eight ounces of
black tea without either milk or sugar; two ounces of white bread or
toast, with a copious layer of butter.

_Dinner_.--2 p.m.:--A modicum of beef marrow soup; four ounces of meat,
preferably of fatty character; moderate quantity of vegetable,
especially the legumines, but no potatoes or anything containing starch;
raw fruits in season, and cooked fruits (stewed, without sugar); two or
three glasses of light wine as a beverage, and after eating, a cup of
black tea without sugar.

_Supper_.--7:30 p m.:--An egg, bit of fat roast, ham, or bacon; a slice
of white bread well buttered; a large cup of black tea without milk or
sugar; from time to time, cheese and fresh fruits.

Germain See suggests as a modification of this regimen, the abundant use
of beverage, the addition of gelatins, and at times small doses of
potassium iodide in twenty cases he claims constant and relatively
prompt results.

Whatever may be urged for Ebstein's system--and it has afforded most
excellent results to Unna and to Lube, as well as its author--it
certainly exposes the patient to the terrors of dyspepsia, when the
routine must needs be interrupted or modified; hence it is not always to
be depended upon. As between dyspepsia and obesity, there are few, I
fancy, who would not prefer the latter.

Another "system" that has acquired no little celebrity, and which has
for its aim the reduction as far as possible of alimentary hydrocarbons
while permitting a certain proportion of fat, is that, of Denneth, which
necessarily follows somewhat closely the lines laid down by Ebstein.

Oertels' treatment, somewhat widely known, and not without due measure
of fame, is based upon a series of measures having as object the
withdrawal from both circulation and the economy at large, as much of
the fluids as possible. It is especially adapted for the relief of those
obese who are suffering fatty degeneration of the heart. The _menu_ is
as follows:

_Breakfast_.--Pour to five ounces of tea or coffee with a little milk;
two to two and a half ounces bread.

_Dinner_.--Three or four ounces of roast or boiled meat, or moderately
fat food; fish, slightly fat; salad and vegetables at pleasure; one and
a half ounces of bread (in certain cases as much as three ounces of
farinaceous food may be permitted); three to six ounces of fruit; at
times a little pastry for dessert.--In summer, if fruit is not
obtainable, six to eight ounces of light wine may be allowed.

_Tea_,--A cupful (four to five ounces) of tea or coffee, with a trifle
of milk, as at breakfast; one and three-fourths ounces of bread; and
exceptionally (and at most) six ounces of water.

_Supper_.--One to two soft boiled eggs; four or five ounces of meat; one
and three fourths ounces of bread; a trifle of cheese, salad, or fruit;
six to eight ounces of light wine diluted with an eighth volume of
water. The quantity of beverage may be slightly augmented at each meal
if necessary, especially if there is no morbid heart trouble.

Schwenninger (Bismarck's physician), who opened a large sanitarium near
Berlin a few years since for the treatment of the obese, employs
Oertel's treatment, modified in that an abundance of beverage is
permitted, provided it is not indulged in at meals; it is forbidden
until two hours after eating.

Both Oertel's and Schwenninger's methods have procured grave dyspepsias,
and fatal albuminurias as well, according to Meyer and Rosenfield. It
has been charged the allowance of beverage upon which Schwenninger lays
so much stress in the treatment at his sanitarium has a pecuniary basis,
in other words a commission upon the sale of wines.[2]

[Footnote 2: The sanitarium is owned by a stock company, Schwenninger
being merely Medical Director.--ED.]

Thus, it will be observed that while some forbid beverage, others rather
insist upon its employment in greater or less quantities. Under such
circumstances, it would seem but rational, before undertaking to relieve
obesity, to establish its exact nature, and also the role taken by
fluids in the phenomena of nutrition.

Physiologists generally admit water facilitates nutritive exchanges,
which is explained by the elimination of a large quantity of urine; the
experiments of Genth and Robin in this direction appear conclusive.

Bischoff, Voit, and Hermann have shown that water increases, not alone
the elimination of urine, but also of sodium chloride, phosphoric acid,
etc. Grigoriantz observed augmentation of disintegration when the
quantity of beverage exceeded forty-six to eighty ounces ("1,400 to
2,400 cubic centimeters") per diem. Oppenheim, Fraenkel, and Debove,
while believing water has but little influence upon the exchanges, admit
it certainly need not diminish the latter; and Debove and Flament, after
administering water in quantities varying from two to eight pints per
diem, concluded that urine was diminished below the former figure, while
above the latter it increased somewhat, being dependent upon the amount
ingested. It was on the strength of the foregoing that Lallemand
declared water to have no influence upon the exchanges.

The results claimed by Oppenheim, Debove, et al. were immediately
challenged--and it is now generally admitted, not without some
justice--by Germain See. It seems certain, to say the least, that water
taken during the repast does tend to augment the quantity and facilitate
the elimination of urine. Abundance of beverage, moreover, presents
other advantages, in that it facilitates digestion by reason of its
diluent action, a fact well worth bearing in mind when treating the
obese who are possessed of gouty diathesis, and whose kidneys are
accordingly encumbered with uric and oxalic acids. The foregoing
presents the ground upon which Germain See permits an abundance of
beverage; but he also expresses strong reservation as regards beer and
alcohol, either of which (more especially the former) tends to the
production of adipose. In his opinion, the only beverage of the
alcoholic class that is at all permissible, and then only for cases
suffering from fatty heart, is a little _liqueur_ or diluted wine.
Coffee and tea he commends highly, and recommends the ingestion of large
quantities at high temperature, both during the repasts and their
intervals. Coffee in large doses is undoubtedly a means of de-nutrition,
and so, too, in no less extent, is tea; both act vigorously owing to the
contained alkaloids, though, to be sure, they sometimes, at first, tend
to insomnia and palpitation, to which no attention need be paid,
however. The treatment outlined by See is:

1. A physiological regimen comprising four to five ounces of nitrogenous
principles as derived from eight to ten ounces animal muscle and
albuminates; three to six ounces of fat; eight to ten ounces of
hydrocarbons as yielded by ten to twelve ounces of sugar or starch food.

These proportions to be modified in such manner that the
musculo-albuminates shall not sensibly exceed the normal ratio, for meat
in excess itself furnishes fat during transformation. The fatty
substances of easy digestion may, without inconvenience, be utilized in
doses of two to three ounces. The hydrocarbons should be reduced to a
minimum. As for the herbaceous elements, they contain nothing nutritive.

2. Beverage, far from being suppressed, should be augmented, in order to
facilitate stomachal digestion and promote general nutrition, though
alcoholic liquids must be inhibited; likewise mineral waters, except,
perhaps, for occasional use. Both should be replaced by infusions of
coffee or tea, taken as hot as can be drank.

Henrich Kisch insists that any method which promises rapid and marked
decrease of adipose must, _per se_, be objectionable, even if not
positively injurious, since it tends to provoke general troubles of
nutrition. He suggests that first the fats and hydrocarbons be reduced
as little as possible; that a moderate mixed regimen is required,
containing a preponderance of albumen, small quantities of hydrocarbons
and gelatinous matters, with but very little fat. Certain fatty meats,
however, should be generally interdicted, such as pork sausage, smoked
beef tongue, goose breast, smoked ham, fat salmon, and herring in any
form. Eggs, however, may be partaken of in moderation, giving preference
to the albumen over the yelk. Farinaceous foods, in the main, should be
rejected, even bread being allowed only in small quantities, and then
preferably in the form of toast. Cheese likewise contains too much fat;
and mushrooms are so rich in hydrocarbons that they should be rejected.
Condiments, water, vegetable acids (vinegars excepted) may be permitted;
especially pernicious is vinegar where there is any tendency to gout or
gravel. All fatty beverages--_bouillon_, unskimmed milk, chocolate, or
cacao--and all alcoholics, are hurtful; breakfast tea is undoubtedly the
best beverage, but, after a little, is advantageously replaced by light
white wine diluted with water.

Kisch believes in a free and abundant use of water by the obese,
especially where there is a tendency to plethora, since this fluid
facilitates oxidation as the result of absorption; thus he advocates the
inhibition of large quantities of cold water by all, save those
presenting evidence of cardiac insufficiency. In short, his regimen is
based upon the administration of a large quantity of albumen, like that
of Harvey-Banting.

E. Munk recommends an almost identical dietary, save that he prefers
great moderation in fluids employed as beverage.

M. Robin has sought to harmonize the opposing views regarding fluids,
and therefore declares obesity arises from two distinct sources: 1.
Augmentation of assimilation. 2. Reduced disassimilation. In the former,
he insists water must be interdicted, while in the latter it may be
allowed _ad libitum_.

Again, in order to recognize the exact variety of obesity, he divides
his patients into three classes, each recognizable by the volume of urea
excreted. In the first there is an increase above normal; in the second
the volume of urea is stationary; in the third decreased, increased, or
stationary.

When the urea is stationary, which is most frequently the case, it is
necessary to calculate the coefficient of oxidation; that is, the
relation existing between the solid matters of the urine and the urea.
The elevation of the coefficient is _prima facie_ evidence the obesity
is due to excess of assimilation, while depression of the coefficient
indicates default of assimilation. In the first case, water and liquids
must be denied as far as possible, the same as if there was no
augmentation of urea; in the second, the same as if there was diminution
of urea, the patients may be permitted to imbibe fluids at pleasure.

For the obese from default of disassimilation, Robin recommends a
regimen of green vegetables and bread chiefly--the latter in small
quantities, however, and fluids as may be desired. By this means, on one
occasion, he was able in the course of one month to diminish the weight
of a female patient by twelve and a half pounds, her measurement around
the waist at the same time decreasing 5.2 inches and across the stomach
4.8 inches.

M. De St. Germain achieved good results by combining judicious exercise
with moderate alimentation, excluding wine and bread.

M. Dujardin Beaumetz, who professes to have given most close and careful
study and attention to regimen for the obese, outlines the following,
provided there is no evidence of fatty degeneration of heart.

_Breakfast_ (at 8 a. m.)--Three-fourths of an ounce of bread "_en
flute_"--that is abounding with crust; one and a half ounces of cold
meat, ham or beef, six ounces weak black tea, _sans_ sugar.

_Lunch_ (at 1 p.m.)--An ounce and a half to two ounces of bread, or a
_ragout_, or two eggs; three ounces green vegetables; one-half ounce of
cheese; fruits at discretion.

_Dinner_ (at 7 p.m.)--An ounce and a half to two ounces of bread; three
to four ounces of meat, or _ragout_; ditto of green vegetables, salad,
half an ounce of cheese, fruit _ad libitum_.

At meal times the patient may take only a "glass and a half" of
liquid--approximately ten ounces--though a greater amount may be
permitted if he abstains during the intervals.

Special alimentary regimen, however, does not constitute the sole
treatment of obesity. Concurrently must be employed a number of
practical adjuvants which are oftentimes of the utmost assistance. For
one thing, exercise is indispensable; all authorities agree on this
point. The exercise taken in the gymnasium is one of the best, notably
the "wall exercise," which is more particularly suited to those
afflicted with pendulous and protuberant abdomens as the result of
feebleness of the hypogastric muscles, to accumulation of fat under the
skin and in the omentum, and to dilation of the stomach and intestines.
In the "wall exercise," the patient stands erect against an absolutely
straight and plumb wall, lifts his hands (carrying a weight) straight
over the head, and causes them to describe a semicircle forward. Zantz
particularly insists upon arm and leg exercise for the obese, especially
the former, since with the same amount of effort a larger amount of
oxygen is consumed than is possible by the latter.

However, of whatever character, the exercise should be continued to the
point of fatigue or dyspnoea--three thousand movements daily,
gradually increased to twenty-five thousand, if the system can bear it;
and under such conditions, not only is there consumption of
hydrocarbons, but there is provided a veritable greed for air that
augments waste. The experiments of Oertel indicate that loss of weight
due to fatiguing exercise arises more particularly from dehydration,
which is made good by absorption of the fluids employed as beverage; the
fluids are claimed by Germain See to act as accelerants of oxidation.

During exercise there is obviously more abundant absorption of oxygen,
and consequently greater elimination of carbonic acid, and as a
consequence (as shown by researches of Voit), the reserve fat of the
economy is attacked and diminished; in intense labor there is an average
hourly consumption of about 8.2 percent. of fat. Further physical
activity is useful in exercising the voluntary muscles, and thus
opposing the invasion by interstitial fat of the muscle fibrils. Extreme
exercise also, to a certain degree, exerts a favorable influence on the
cardiac muscle, augmenting both its nutrition and its capacity for
labor. With the anæmic obese, however, it is necessary to be most
circumspect in prescribing forced exercise; also with the elderly obese
possessed of enfeebled or fatty heart.

Hydrotherapy, especially in the form of cold douches, particularly when
combined with massage, is often of considerable value in relieving
obesity; the method of Harmman, of St. Germain, which has in many
instances induced rapid loss of adipose, is of this class. Tepid saline
baths and vapor baths have many advocates, and may afford material aid
when the heart and circulation do not inhibit their employment. Hot
baths elevate the temperature of the body and increase the organic
exchanges, hence, as Bert and Reynard have pointed out, tend to the
elimination of oxygen and carbonic acid; but when employed, the patient
should be introduced while the temperature is below 130° F., when it may
be gradually raised in the course of thirty or forty minutes to 140° F.

It has already been intimated, the chief feature of the treatment of
obesity is acceleration of the exchanges; and this is in the main true,
though it must also be borne in mind that, while there are obese who
excrete little urea and have a depressed central nervous temperature,
many may be azoturic, and besides eliminate phosphate in excess, when an
oxidating treatment will not only fail, but prove positively injurious.

The bile throws out fat, therefore, to accelerate nutritive oxidations,
the liver and nervous system must be acted upon, _i.e._, stimulated.
Everything that tends to diminish the activity of the former, or depress
the latter, must be avoided. Hence intellectual labor should be
encouraged, or in lieu thereof, travel advised. Exercise should be taken
chiefly while fasting; the limits of sleep confined to strict necessity,
and _siestas_ after meals and during the day strictly forbidden; the
skin stimulated by hydro-therapeutic measures, including massage under
cold affusions, during warm salt baths, etc.

To increase the activity of the liver, salicylate of soda may often be
advantageously administered for its cholagogue effect; or resort may be
had to saline purgatives such as are afforded by the springs of
Marienbad, Kissengen, Homburg, Carlsbad, Brides, Hunyadi, or
Chatel-Guyon; and it is somewhat remarkable that while undergoing a
course of these waters, there is often no appreciable change in weight
or obesity, though the decrease becomes most marked almost immediately
upon cessation of treatment.

Everything tending to increased or fuller respiration is to be
encouraged, for the fats are thus supplied with oxygen, hastening their
disintegration and consumption.

Direct medicinal treatment presents no very wide scope. Bouchard
imagines lime water may be useful by accelerating nutrition, but this is
problematical, since fat in emulsion or in droplets does not burn.
Nevertheless, alkalies in general, alkaline carbonates, liquor potassa,
soaps, etc., aid in rendering fat more soluble, and consequently more
susceptible to attack. The alkaline waters, however, are much less
active in obesity than the saline mineral waters, unless, as sometimes
happens, there is a complication of diabetes and obesity.

Purgatives are always more or less useful, and often required to be
renewed with all the regularity of habit. Then too, the iodides,
especially iodide of sodium or potassium, as recommended by M. Germain
See, frequently prove of excellent service by aiding elimination and
facilitating the mutations.

According to Kisch, the cold mineral waters containing an abundance of
sulphate of soda, like Hunyadi and Marienbad, are to be preferred to the
hot mineral waters, such as Carlsbad, because of their lesser irritant
action on the vascular system, and because they strongly excite diuresis
through their low temperature and contained carbonic acid; Carlsbad
deserves preference only when obesity is combined with uric acid
calculi, or with diabetes. For very anæmic persons, however, the weak
alkaline and saline waters should be selected; or they should confine
themselves to chalybeate waters containing an excess of sulphate of
soda. Water containing sulphate of soda is also indicated as a beverage
where there are troubles of the circulatory apparatus; it is
contraindicated only in accentuated arterio-sclerosis.

As a matter of fact, I find the suggestion of M. Dujardin-Beaumetz,
that the obese should be divided into two groups, a most practical one,
for some are strong and vigorous--great eaters, perhaps even
gluttons--while others, on the contrary, are feeble and debilitated,
with flesh soft and flaccid; and upon the former may be imposed all the
rigors of the reducing system, while the latter must be dealt with more
carefully.

In general, it must be noted, the regimen prescribed for the obese is
insufficient, as the following table prepared by M.C. Paul abundantly
proves:

    -------------------------+----------+----------+---------------
           Author.           |Albuminous|  Fatty   |
                             | Matters. | Matters. | Hydrocarbons.
    -------------------------+----------+----------+---------------
    Voit.                    |    118   |    40    |     150
    Harvey-Banting.          |    170   |    10    |      80
    Ebstein.                 |    100   |    85    |      50
    Oertel.                  |  155-179 |  25-41   |    70-110
    Kisch (plethoric).       |    160   |    10    |      80
      "   (anæmic).          |    200   |    12    |     100
    Normal ration.           |    124   |    55    |     455
    -------------------------+----------+----------+---------------

There is, therefore, as Dujardin-Beaumetz asserts, autophagia in the
obese, and all these varieties of treatment have but one end, viz.:
Reduction of the daily ration. But the quantity of nourishment should
not be too greatly curtailed, for, manifestly, if the fat disappears the
more surely, the muscles (rich in albumen) undergo too rapid
modification. It is progressive action that should always be sought.

The quantity of aliment may be reduced either by imposing an always
uniform regimen, which soon begets anorexia and disgust, or by
withholding from the food a considerable quantity of fat, or, finally,
by forbidding beverage during meals. Emaciation is obtained readily
enough in either way, and demands only the constant exercise of will
power on the part of the patient; but unhappily, severe regimen cannot
always be prescribed. When the obese patient has passed the age of
forty; when the heart suffers from degeneration; or when the heart is
anæmic--in all, rigorous treatment will serve to still further enfeeble
the central organ of circulation, and tend to precipitate accidents
that, by all means, are to be avoided. In such cases, by _not_ treating
the obesity, the days of the patient will be prolonged. In degeneration
of the heart, however, the method of Ebstein may be tried; and when
there is renal calculi and gouty diathesis, that of Germain See may
prove satisfactory.

Paris, France.

       *       *       *       *       *




STILT WALKING.


[Illustration: SYLVAIN DORNON, THE STILT WALKER OF LANDES.]

Sylvain Dornon, the stilt walker of Landes, started from Paris on the
12th of last March for Moscow, and reached the end of his journey at the
end of a fifty-eight days' walk. This long journey upon stilts
constitutes a genuine curiosity, not only to the Russians, to whom this
sort of locomotion is unknown, but also to many Frenchmen.

Walking on stilts, in fact, which was common twenty years ago in certain
parts of France, is gradually tending to become a thing of the past. In
the wastes of Gascony it was formerly a means of locomotion adapted to
the nature of the country. The waste lands were then great level plains
covered with stunted bushes and dry heath. Moreover, on account of the
permeability of the subsoil, all the declivities were transformed into
marshes after the slightest fall of rain.

There were no roads of any kind, and the population, relying upon sheep
raising for a living, was much scattered. It was evidently in order to
be able to move around under these very peculiar conditions that the
shepherds devised and adopted stilts. The stilts of Landes are called,
in the language of the country, _tchangues_, which signifies "big legs,"
and those who use them are called _tchanguès_. The stilts are pieces of
wood about five feet in length, provided with a shoulder and strap to
support the foot. The upper part of the wood is flattened and rests
against the leg, where it is held by a strong strap. The lower part,
that which rests upon the earth, is enlarged and is sometimes
strengthened with a sheep's bone. The Landese shepherd is provided with
a staff which he uses for numerous purposes, such as a point of support
for getting on to the stilts and as a crook for directing his flocks.
Again, being provided with a board, the staff constitutes a comfortable
seat adapted to the height of the stilts. Resting in this manner, the
shepherd seems to be upon a gigantic tripod. When he stops he knits or
he spins with the distaff thrust in his girdle. His usual costume
consists of a sort of jacket without sleeves, made of sheep skin, of
canvas gaiters, and of a drugget cloak. His head gear consists of a
beret or a large hat. This accouterment was formerly completed by a gun
to defend the flock against wolves, and a stove for preparing meals.

The aspect of the Landeses is doubtless most picturesque, but their
poverty is extreme. They are generally spare and sickly, they are poorly
fed and are preyed upon by fever. Mounted on their stilts, the shepherds
of Landes drive their flocks across the wastes, going through bushes,
brush and pools of water, and traversing marshes with safety, without
having to seek roads or beaten footpaths. Moreover, this elevation
permits them to easily watch their sheep, which are often scattered over
a wide surface. In the morning the shepherd, in order to get on his
stilts, mounts by a ladder or seats himself upon the sill of a window,
or else climbs upon the mantel of a large chimney. Even in a flat
country, being seated upon the ground, and having fixed his stilts, he
easily rises with the aid of his staff. To persons accustomed to walking
on foot, it is evident that locomotion upon stilts would be somewhat
appalling.

One may judge by what results from the fall of a pedestrian what danger
may result from a fall from a pair of stilts. But the shepherds of
Landes, accustomed from their childhood to this sort of exercise,
acquire an extraordinary freedom and skill therein. The _tchanguè_ knows
very well how to preserve his equilibrium; he walks with great strides,
stands upright, runs with agility, or executes a few feats of true
acrobatism, such as picking up a pebble from the ground, plucking a
flower, simulating a fall and quickly rising, running on one foot, etc.

The speed that the stilt walkers attain is easily explained. Although
the angle of the legs at every step is less than that of ordinary
walking with the feet on the ground, the sides prolonged by the stilts
are five or six feet apart at the base. It will be seen that with steps
of such a length, distances must be rapidly covered.

When, in 1808, the Empress Josephine went to Bayonne to rejoin Napoleon
I, who resided there by reason of the affairs of Spain, the municipality
sent an escort of young Landese stilt walkers to meet her. On the
return, these followed the carriages with the greatest facility,
although the horses went at a full trot.

During the stay of the empress, the shepherds, mounted upon their
stilts, much amused the ladies of the court, who took delight in making
them race, or in throwing money upon the ground and seeing several of
them go for it at once, the result being a scramble and a skillful and
cunning onset, often accompanied with falls.

Up to recent years scarcely any merry-makings occurred in the villages
of Gascony that were not accompanied with stilt races. The prizes
usually consisted of a gun, a sheep, a cock, etc. The young people vied
with each other in speed and agility, and plucky young girls often took
part in the contests.

Some of the municipalities of the environs of Bayonne and Biarritz still
organize stilt races, at the period of the influx of travelers; but the
latter claim that the stiltsmen thus presented are not genuine Landese
shepherds, but simple supernumeraries recruited at hazard, and in most
cases from among strolling acrobats. The stilt walkers of Landes not
only attain a great speed, but are capable of traveling long distances
without appreciable fatigue.

Formerly, on the market days at Bayonne and Bordeaux, long files of
peasants were seen coming in on stilts, and, although they were loaded
with bags and baskets, they came from the villages situated at 10, 15,
or 20 leagues distance. To-day the sight of a stilt walker is a
curiosity almost as great at Bordeaux as at Paris. The peasant of Landes
now comes to the city in a wagon or even by railway.--_La Nature_.

       *       *       *       *       *




REMAINS OF A ROMAN VILLA IN ENGLAND.


A correspondent of the _Lincolnshire Chronicle_ writes: For some weeks
past, remains of a Roman villa have been exposed to view by Mr.
Ramsden's miners in Greetwell Fields. From, the extent of the tesselated
pavements laid bare there is hardly any doubt that in the Greetwell
Fields, in centuries long gone by, there stood a Roman mansion, which
for magnitude was perhaps unrivaled in England. Six years ago I drew
attention to it. The digging for iron ore soon after this was brought to
a standstill by the company, which at the time was working the mines,
ceasing their operations. Then the property came into other hands, and
since then more extensive basement floors of the villa have from time to
time been laid bare, and from tentative explorations which have been
just made, still more floors remain to be uncovered which may be of a
most interesting and instructive character. What a pity it is that the
inhabitants of Lincoln have not made an effort to preserve these
precious relics of the grandeur of the Roman occupation, an occupation
to which England owes so much. From the Romans the people of this
country inherit the sturdy self-reliance and perseverance in action
which have helped to make England what it is, and from the Romans too,
in a great degree, does England also inherit her colonizing instincts,
which impel her people to cover the waste places of the world with
colonies. If the Roman remains which have been so abundantly discovered
of late years in Lincoln and its vicinity had been collected and laid
out for exhibition, they would have formed a most interesting collection
of antiquities worthy of the town, and well worth showing to visitors
who now annually make Lincoln a visitation. Although these relics of a
remote age are being dug up and are being destroyed, it is not the fault
of Mr. Ramsden, for he not only preserved them as long as he
conveniently could, but he also had the soil removed from over them, and
had them thoroughly washed, in order that people might have an
opportunity of seeing their extent and beauty. One of these patches of
pavement extended 48 yards northward from what might be called the main
building, which had previously been broken up. This strip was 13 ft. in
breadth, and down its center ran an intricate pattern worked in blue
tesseræ. The pattern is much used in these days in fabrics and works of
art, and is, I think, called the Grecian or Roman key pattern. On each
side of this ran alternately broad ribbons of white and narrower ribbons
of red tesseræ. There is also another strip of pavement to the south of
the preceding patch, which has been laid bare to the extent of 27 yards.
This patch is about 10 ft. in breadth, and its western portion is cut up
in neat patterns, which show that they formed the floors of rooms. From
the eastern extremity of these floors evidently another long strip of 48
or 50 yards still remains to be uncovered. Doubtless there are other
remains beneath the ground which will be laid bare as the work of mining
goes on. All these floors were not deeper than from 18 to 30 inches
below the surface of the soil. The bones of animals and other relics
have been found in the covering soil and have been turned up by the
miners from time to time. The pavement is all worked out with cubes,
varying in size from an inch and a half to two inches square, each piece
being placed in position with most careful exactness. The strip which
extends 48 yards and is 13 ft. wide runs due north and south. There is a
second patch, running east and west, and this is 27 ft. long by 10 ft.
wide, while a third is 27 ft. long by 11 ft. wide, this also running in
a northern direction. To the north of this latter piece, and separated
only by about two feet (about the width of a wall, which very possibly
was the original division), there is a strip of tesseræ 16 ft. wide,
which had been laid bare 40 yards. It was thought probable that at the
end of the last named strip still another patch would be found. Mr.
Ramsden, the manager of the Ironstone Works, is keeping a plan of the
whole of the pavement, which he is coloring in exact imitation of the
original work. This, when completed, will be most interesting, and he
will be quite willing to show it to any one desirous of inspecting the
same. Many persons have paid a visit to the spot where the discoveries
have been made, and surprise is invariably expressed at the magnitude
and beautiful symmetry of the work.

Several interesting fragments of Roman work have been brought to light
in the course of excavations that are being made for building purposes
at Twyford, near Winchester. About a month ago, a paved way, composed
entirely of small red tiles, six feet in width and extending probably a
considerable distance (a length of 14 ft. was uncovered), was found
while digging on the site for flints. The more recent excavations are 20
ft. west of this passage, and there is now to be seen, in a very perfect
state of preservation, an oven or kiln with three openings. Five yards
away from this is a chamber about eight feet square, paved with tiles,
and the sides coated with a reddish plaster. On one side is a ledge 15
in. from the ground, extending the whole length of the chamber; on the
floor is a sunk channel with an opening at the end for the water to
escape. This chamber evidently represents the bath. Portions of the
dividing walls of the different chambers have also been discovered,
together with various bones, teeth, horns and ornaments, but very few
coins. It is probable that an alteration in the plans of the house which
was about to be built on the spot will be made so as to preserve all the
more interesting features of these remains in the basement. These
discoveries were made at a depth of only two or three feet from the
surface of the ground, and are within about a quarter of a mile of other
Roman remains which were similarly brought to light a few months ago.

       *       *       *       *       *

[Continued from SUPPLEMENT, No. 830, page 13110.]




GUM ARABIC AND ITS MODERN SUBSTITUTES.[1]

[Footnote 1: A paper read before the Society of Chemical Industry,
London, 1891. From the Journal]

BY DR. S. RIDEAL AND W.E. YOULE.


Subjoined is a table giving the absolute viscosity of various gums. A
comparison of the uncorrected viscosities with the corrected shows the
great importance of Slotte's correction for dextrins and inferior gum
arabics; in other words, for solutions of low viscosity, while it will
be observed to have little influence upon the uncorrected [eta] obtained
for the Ghatti gums and the best samples of gum arabic.

TABLE OF ABSOLUTE VISCOSITIES OF 10 PER CENT. GUM AND DEXTRIN SOLUTIONS.

    ---------------------+--------------+------------+----------
           Sample.       |     [eta]    |    [eta]   | Z Water
                         | Uncorrected. | Corrected. |  = 100.
    ---------------------+--------------+------------+----------
    Gum arabic.......... |    0.1876    |   0.1856   |  1,233
    Cape gum............ |    0.1575    |   0.1555   |  1,029
    Indian gum.......... |    0.0540    |   0.0470   |    311
    Eastern gum......... |    0.0689    |   0.0639   |    417
    Gum arabic.......... |    0.0550    |   0.0480   |    317
    Senegal............. |    0.0494    |   0.0410   |    271
    Senegal............. |    0.0468    |   0.0380   |    251
    Senegal............. |    0.0627    |   0.0557   |    364
    Gum arabic.......... |    0.0511    |   0.0430   |    285
    Water............... |    0.0149    |   0.0124   |    100
    Ghatti.............. |    0.2903    |   0.2880   |  2,322
    Ghatti, 5 per cent.. |    0.0903    |   0.0828   |    688
    Ghatti, 5 per cent.. |    0.1391    |   0.1350   |  1,089
    Ghatti, 5 per cent.. |    0.1795    |   0.1760   |  1,420
    Ghatti, 5 per cent.. |    0.1527    |   0.1485   |  1,198
    Ghatti, 5 per cent.. |    0.1139    |   0.1083   |    873
    Ghatti, 5 per cent.. |    0.1419    |   0.1369   |  1,104
    Dextrin............. |    0.0398    |   0.0255   |    169
    Dextrin............. |    0.0341    |   0.0196   |    129
    Dextrin............. |    0.0455    |   0.0380   |    306
    Gum substitute...... |    0.0318    |   0.0224   |    180
    Gum substitute...... |    0.0318    |   0.0224   |    180
    Amrad............... |    0.0793    |   0.0708   |    570
    Australian.......... |    0.0378    |   0.0283   |    228
    Australian.......... |    0.0365    |   0.0268   |    216
    Brazilian........... |    0.0668    |   0.0627   |    506
    Brazilian........... |    0.0516    |   0.0445   |    359
    Ghatti.............. |    0.3636    |   0.3621   |  2,920
    ---------------------+--------------+------------+----------

In the column for [eta] corrected the differences due to the use of
different instruments are of course eliminated. The absolute viscosity
of water at 15° C. determined in four different instruments is shown
below. Poiseuille's value for water being 0.0122.

 --------------+-------------+-------------+-------------+-------------+
   Instrument. |      1.     |      2.     |      3.     |      4.     |
 --------------+-------------+-------------+-------------+-------------+
 [eta] corrtd. |      0.0109 |     0.01185 |      0.0124 |      0.0120 |
     of water. |             |             |             |             |
 K_{1} value.. | 0.000000898 | 0.000000863 | 0.000000932 |  0.00000052 |
 K_{2} value.. |       0.235 |      0.2175 |       0.226 |      0.0204 |
 --------------+-------------+-------------+-------------+-------------+

The above values for various gums and dextrins were obtained at a
constant temperature of 15° C. and are compared with water at that
temperature. It is of the utmost importance that the temperature of the
water surrounding the bulbs should be adjusted for each series of
experiments to the temperature at which the absolute viscosity of the
water was determined. As far as we have ascertained, in gum solutions
there is a steady diminution in viscosity with increase of temperature
until a certain temperature is reached, beyond which increase of heat
does not markedly influence the viscosity, and it is possible that above
this "critical point," as we may term it, the gum solutions once more
begin to increase in viscosity. The temperature at which the viscosity
becomes stationary varies somewhat with different gums, but broadly
speaking it lies between 60° C. and 90° C., no gums showing any marked
decrease in viscosity between 80° C. and 90° C.

The experiments we have made in this direction were conducted as
follows. The 300 c.c. bottle containing the gum was placed in a
capacious beaker full of hot water, and the viscosity instrument was
also surrounded with water at the same temperature. Thermometers were
suspended both in the beaker and the outer jar. The viscosity at the
highest temperature obtained, about 90° C., was then taken and repeated
for every fall of 4° C. till the water reached the temperature of the
air.

The values so obtained gradually diminished with the increase of
temperature. From the [eta] values obtained the Z values were
calculated, using water at 15° C. as a standard. From the Z values thus
obtained taken as the ordinate, and the temperature of each experiment
as the abscissa, curves were plotted out embodying the results, examples
of which are given below. The curves yielded by three gums 2, 7, and 8
changed between 90° C and 100° C., while gum sample 4 has a curve
bending between 60° C. and 70° C. Experimentally this increase of
viscosity of the latter gum above 60° C. was confirmed, but the critical
point of the other solutions tried approaches too nearly to the boiling
point of water for experiments to be conducted with accuracy, as the
temperature of the bulbs diminishes sensibly while the experiment is
being made.

If viscosity values have been determined it is possible to calculate the
remaining or intermediate values for Z at any particular temperature
from the general equation--

      Zt = A + Bt + Ct²

As an example of the mode of calculation we may quote the following. A
gum gave the following values for Z at the temperature stated:

     Gum. 50° C. Z_{50°} = 228

     Gum. 30° C. Z_{30°} = 339

     Gum. 20° C. Z_{20°} = 412

from which the constants--

     A = 592.99     B = -10.2153     C = 0.0583

can be obtained, and thus the value of Z_{t°} for any required
temperature. The numbers calculated for gums all point to a diminution
in viscosity up to a certain point, and then a gradual increase. A
comparison of some of the figures actually obtained in some of these
experiments, compared with the calculated figures for the same
temperature, shows their general agreement.

[Illustration: Curves showing viscosity change with temperature for
three typical gums. A--Arabic VII. B--Senegal VIII. C--Ghatti 15.]

    EFFECT OF TEMPERATURE UPON VISCOSITY--GUM VII.

     ------------+------+--------+-------------+
     Temperature.| [eta]|Z found.|Z calculated.|
     ------------+------+--------+-------------+
         °C      |      |        |             |
         50      |0.0283|  228   |   228.00    |
         45      |0.0305|  246   |   246.55    |
         42      |0.0352|  284   |   266.75    |
         38      |0.0368|  297   |   289.00    |
         34      |0.0410|  330   |   313.06    |
         30      |0.0419|  339   |   339.00    |
         26      |0.0445|  359   |   367.80    |
         22      |0.0492|  398   |   396.47    |
         20      |0.0511|  412   |   412.00    |
         18      |0.0531|  428   |   428.00    |
     ------------+------+--------+-------------+

    EFFECT OF TEMPERATURE UPON VISCOSITY.--GUM VIII.

     ------------+------+--------+-------------|
     Temperature.| [eta]|Z found.|Z calculated.|
     ------------+------+--------+-------------|
          °C.    |      |        |             |
          50     |0.0430|  347   |    347      |
          46     |0.0475|  383   |    371.14   |
          42     |0.0502|  405   |    397.09   |
          38     |0.0510|  411   |    424.73   |
          34     |0.0575|  463   |    454.06   |
          30     |0.0602|  485   |    485      |
          26     |0.0637|  513   |    517.82   |
          22     |0.0667|  538   |    552.25   |
          20     |0.0707|  570   |    570      |
          18     |0.0755|  609   |    583.07   |
     ------------+------+--------+-------------+

The constants for the first gum are those given in the preceding column,
while for the latter they were--

     A = 771.9:  B = -11.15:  C = 0.053

As will be observed, the effect of heat appears to be the same upon the
two typical gum arabics quoted above, an increase of temperature from
18° C. to 50° C. decreasing the viscosity by nearly one half in both
cases, and the same seems to be true of most gum arabics. Roughly also
the same holds good for Ghattis, as the following numbers show:

    ------------+-------------+------------|
        Gum.    | Z at 18° C. | Z at 50° C.|
    ------------+-------------+------------|
    Gum arabic. |    1016     |    579     |
    Gum arabic. |     428     |    228     |
    Gum arabic. |     609     |    347     |
    Gum arabic. |     581     |    258     |
    Ghatti.     |     572     |    306     |
    Ghatti.     |     782     |    418     |
    ---------------------------------------+

The following table shows the effect of heat upon the viscosity of a
typical Ghatti:

  GHATTI GUM NO. 15.--VISCOSITY.

   ------------+------+-----|
   Temperature.| [eta]|  Z. |
   ------------+------+-----|
       °C.     |      |     |
       50      |0.0517| 418 |
       46      |0.0581| 468 |
       42      |0.0628| 506 |
       38      |0.0726| 585 |
       34      |0.0788| 635 |
       30      |0.0857| 691 |
       26      |0.0889| 717 |
       22      |0.0919| 741 |
       20      |0.0946| 763 |
       18      |0.0964| 777 |
   ------------+------+-----+

There is therefore no essential difference in the behavior of a Ghatti
and a gum arabic on heating. Some interesting results, however, were
obtained by heating gums, both Ghattis and arabics, at a fixed
temperature for the same time, cooling, and then after making the
solutions up to the original volume taking their viscosities at the
ordinary temperature. The effect of heating for two hours to 60° C., 80°
C., or 100° C. was a small permanent alteration in viscosity of the
solution, and it would therefore seem desirable that gum solutions
should be made up cold to get the maximum results. The following numbers
illustrate this change, viz.:

------------------------+-----------+-----------------------+
                        |           |    After heating to   |
Gum Arabic              |   Without |-------+-------+-------+
10 Per Cent.            |    heat.  | 60°C. | 80°C. | 100°C |
------------------------+-----------+-------+-------+-------+
Z at 18°C               |    570    |  468  |  470  |  517  |
Z at 30°C               |    485    |  400  |  422  |  439  |
Z at 50°C               |    347    |  287  |  258  |  301  |
Ghatti gum No. 15,      |           |       |       |       |
 5 per cent. Z at 18°C. |  1,104    |  780  |  660  |  758  |
------------------------+-----------+-------+-------+-------+

The variation of viscosity with strength of solution was also studied
with one or two typical gums. A 10 per cent. is invariably more than
twice as viscous as a 5 per cent. solution. The following curve was
obtained from one of the Ghattis. Similar results were shown by other
gums.

[Illustration: Variation of Viscosity, with Dilution. Ghatti No. 888.]

It would seem, therefore, that strong solutions, say of 50 per cent.
strength, would be more alike in viscosity than solutions of 5 per cent.
strength of the same gums. In other words, the viscosity of a gum
solution should be taken as nearly as possible to the strength it is
used at, to obtain an exact quantitative idea of its gumming value.

The observation of this fact was one of the circumstances which decided
us to use 5 per cent. solutions for the determination of Ghatti gum
viscosities, the ratio between the 5 per cent. and 10 per cent.
solutions of gum arabics being roughly the same as that between the
respective weights required for gumming solutions of equal value.

From observation of the general nature of the solutions of Ghatti gums,
and from the fact that when allowed to stand portions of the apparently
insoluble matter passed into solution, the hypothesis suggested itself
that metarabin was soluble in arabin, although insoluble in cold water.
If this hypothesis were correct, it would explain the apparent anomaly
of Ghattis giving solutions of higher viscosity than gum arabics,
although they leave insoluble matter behind. The increase in viscosity
would be due to the thickening of the arabic acid by the metarabin.
Moreover, the solutions yielded by various Ghattis leaving insoluble
matter behind would _be all of the same kind_, viz., a saturated
solution of metarabin in arabin more or less diluted by water. Still
further, if the insoluble residue of a Ghatti be the residual metarabin
over and above that required to saturate the arabin, then it will be
possible to dissolve this by the addition of more arabin in the form of
ordinary gum arabic. In order to see if this were the case the following
experiments were performed. Equal parts of a Ghatti and of a gum arabic
were ground up together and dissolved in water. The resulting solution
was _clear_. It was diluted until of 10 per cent. strength, and its
viscosity then taken:

---------------------+-------------+----------------+
                     | Contains 50 per Cent. Ghatti.|
---------------------+-------------+----------------+
A. Pressure 200 mm   |    [eta]    |      Z.        |
Temperature 15° C    |    0.2517   |    2,030       |
---------------------+-------------+----------------+

The viscosity of this solution therefore was considerably greater than
the mean viscosity of the 10 per cent. solutions of the Ghatti and the
gum arabic, viz., (0.288 + 0.0636)/2 = 0.1758 for the calculated [eta].
Hence it is evident that the increase in viscosity is due to the
solution of the metarabin.

Next a solution was made from a mixture of 70 per cent. Ghatti and 30
per cent. gum arabic. This was also clear and gave a considerably higher
viscosity than the previous solution.

---------------------+------------------------------+
                     | Contains 70 per Cent. Ghatti.|
---------------------+-------------+----------------+
B. Pressure 200 mm   |    [eta]    |      Z.        |
Temperature 15° C    |    0.3177   |    2,562       |
---------------------+-------------+----------------+

It will be obvious that the increase of viscosity over the previous
solution in this case must be due to the smaller amount of the thin gum
arabic which is present, _i.e._, in the first case there is more gum
arabic than is required to dissolve the whole of the insoluble
metarabin. Further experiments showed that this is also true of the
second mixture, as the viscosities of the following mixtures
illustrate:

    -------------------------+--------+-------+
      Strength of Solution.  | [eta]  |   Z.  |
    -------------------------+--------+-------|
    C. 80 per cent. Ghatti.  |0.3642  | 2,937 |
    D. 75 per cent. Ghatti.  |0.33095 | 2,669 |
    E. 77.5 per cent. Ghatti.|0.4860  | 3,819 |
    -------------------------+--------+-------+

This last solution E we called for convenience the "maximum viscosity"
solution, as we believe it to be a 10 per cent. solution containing
arabin very nearly saturated with metarabin. As will be observed, its
viscosity differs widely from those of solutions C and D, between which
it lies in percentage of Ghatti. The first named solution C contains
_too little_ of gum arabic to dissolve the whole of the metarabin.
Consequently there is a residue left undissolved, which of course
diminishes its viscosity. The second solution D is too low in viscosity,
as it still contains too much of the weak gum arabic, and as will be
seen further on, a very slight change in the proportions increases or
decreases the viscosity enormously.

We next tried a series of similar experiments with a Ghatti containing
far less insoluble residue and which consequently would require less gum
arabic to produce a perfect solution. Mixtures were made in the
following proportions, viz.:

    ----------------------+------------+-----------+
            -----         | 13.3 per Cent. Ghatti. |
    ----------------------+------------+-----------+
    F. Pressure 200 mm.   |      [eta] |     Z.    |
       Temperature 15° C. |     0.0976 |    787    |
    ----------------------+------------+-----------+

    ----------------------+------------+-----------+
            -----         | 86.6 per Cent. Ghatti. |
    ----------------------+------------+-----------+
    G. Pressure 200 mm.   |      [eta] |     Z.    |
       Temperature 15° C. |     0.4336 |   3,497   |
    ----------------------+------------+-----------+

This latter solution is approaching fairly closely to our "maximum
viscosity" with the previous Ghatti, and probably a very slight decrease
in the amount of gum arabic would bring about the required increase in
viscosity.

When these experiments were first commenced we were still under the
impression, which several months' experience of working with gums had
produced, namely, that the Ghattis were quite distinct in their
properties to ordinary gum arabics. But the new hypothesis, and the
experiments undertaken to confirm it, showed clearly that if the
viscosity of a gum solution depends on the ratio of metarabin to arabin,
then there is no absolute line of demarkation between a Ghatti and a gum
arabic. In other words, there is a constant gradation between gum arabic
and Ghattis, down to such gums as cherry gum, consisting wholly of
metarabin and quite insoluble in water. Therefore those gum arabics
which are low in viscosity consist of nearly pure arabin, while as the
viscosity increases so does the amount of metarabin, until we come to
Ghattis which contain more metarabin than their arabin can hold in
solution, when their viscosity goes down again.

From these observations it would follow, that by taking a gum of less
viscosity than the gum arabic previously used to dissolve the Ghatti,
less of it would be required to do the same work. We confirmed this
suggestion experimentally by taking another gum arabic of viscosity
0.0557 at 15° C. A mixture containing 93.3 per cent. of this Ghatti and
6.7 per cent. of our thinnest gum arabic gave a clear solution which had
the highest viscocity we have yet obtained for a 10 per cent. solution.

    ----------------------+--------+-------+
    H. Pressure 200 mm.   |  [eta] |   Z.  |
       Temperature 15° C. | 0.5525 | 4,456 |
    ----------------------+--------+-------+

This gum arabic may be regarded as nearly pure arabin (as calcium and
potassium, etc., salt). By diluting the new "maximum viscosity"
solution, therefore, with the 10 per cent. solution of the gum arabic in
fixed proportions we obtain a series of viscosities which are shown in
the following curve.

[Illustration: Curve Showing Influence of Ghatti upon Viscosity.]

Besides obtaining this curve for change in viscosity from maximum amount
of metarabin to no metarabin at all, we also traced the decrease in
viscosity of the "maximum" solution by dilution with water. The
following numbers were thus obtained, and plotted out into a curve.

Having obtained this curve, we are now in a position to follow up the
hypothesis by calculating the surplus amount of insoluble matter in a
Ghatti. For, let it be conceded that the solution of any Ghatti leaving
an insoluble residue is a mixture of arabin and metarabin in the same
ratio as our "maximum" solution, only more diluted with water, then from
the found viscosity we obtain a point on the curve for dilution, which
gives the percentage of dissolved matter.

Now to show the use of this: The Z value for a 10 per cent. solution of
the second Ghatti at 15° C. is 2,940. This corresponds on the curve to
8.4 dissolved matter. 10 - 8.4 = 1.6 grammes in 10 grammes, which is
insoluble.

CHANGE OF VISCOSITY WITH DILUTION--"MAXIMUM" SOLUTION. 15° C.
TEMPERATURE.

    ------------+--------------+---------
    Percentage. | [eta]        |     Z.
    ------------+--------------+---------
        10      |    0.55250   |   4,456
         9      |    0.42850   |   3,456
         8      |    0.35120   |   2,832
         7      |    0.27660   |   2,230
         6      |    0.22290   |   1,797
         5      |    0.16810   |   1,355
         4      |    0.11842   |     955
         3      |    0.08020   |     647
         2      |    0.06190   |     499
         1      |    0.03610   |     291
    ------------+--------------+---------

[Illustration: Curve of Variation in Viscosity on Dilution of the
"Maximum" Solution.]

We have already shown that a "maximum" viscosity solution of this gum is
formed when 6.7 per cent, of thin gum arabic is added to it, and
therefore 6.7 parts of a thin gum arabic are required to bring 16 parts
of metarabin into solution. A convenient rule, therefore, in order to
obtain complete solution of a Ghatti gum is to add half the weight in
thin gum of the insoluble metarabin found from the viscosity
determination. But the portion of the gum which dissolved is made up in
a similar manner (being a diluted "maximum" solution).

Therefore the 84 per cent. of soluble matter contains 58 parts of
metarabin, and the total metarabin in this gum is 58 + 16 = 74 per cent,
on the dry gum.

With these solutions of high viscosity some other work was done which
may be of interest. The temperature curves of the mixtures marked E, G,
and F were obtained between 60° C. and 15° C. The two former curves
showed a direction practically parallel to that at the 10 per cent.
solutions, and as they were approaching to the "maximum" solution, this
is what one would expect. Mr. S. Skinner, of Cambridge, was also good
enough to determine the electrical resistances of these solutions and
the Ghattis and gum arabics employed in their preparation. The
electrical resistance of these gum solutions steadily diminishes as the
temperature increases, and the curve is similar to those obtained for
rate of change with temperature. Although the curves run in, roughly,
the same direction, there does not appear to be any exact ratio between
the viscosities of two gums say at 15° C. and their electrical
resistances at the same temperature; hence it would not seem possible to
substitute a determination of the electrical resistance for the
viscosity determination. The results appear to be greatly influenced by
the amount of mineral matter present, gums with the greatest ash giving
lower resistances.

Experiments were conducted with two Ghattis and two gum arabics, besides
the mixtures marked E, F, and H. Comparison of the electrical
resistances with the viscosities at 15° C. shows the absence of any
fixed ratio between them.

    -----------+------+-------------+------------
      Gum or   |  °C. |    Ohms     | Z Viscosity
      Mixture. |      | Resistance. |   at 15° C.
    -----------+------+-------------+-------------
    Ghatti, 1  | 10   |    5,667    |    1,490
    Ghatti, 2  | 15   |    2,220    |    2,940
    Arabic 1   | 15   |    1,350    |      605
    Arabic 2   | 10   |    2,021    |      449
    Mixture F  | 15   |    1,930    |      787
    Mixture E  | 11.3 |    2,058    |    3,919
    -----------+------+-------------+-------------

While performing these experiments, an attempt was made to obtain an
"ash-free" gum, in order to compare its viscosity with that of the same
gum in its natural state. A gum low in ash was dissolved in water, and
the solution poured on to a dialyzer, and sufficient hydrochloric acid
added to convert the salts into chlorides. When the dialyzed gum
solution ceased to contain any trace of chlorides, it was made up to a
10 per cent. solution, and its viscosity determined under 100 mm.
pressure, giving the following results at 15° C.:

    -----------------+--------------+-----
        --------     | [eta]        |  Z
    -----------------+--------------+-----
    Natural gum..... |    0.05570   | 449
    "Ash-free" gum.. |    0.05431   | 438
    -----------------+--------------+-----

Thus showing that the viscosity of pure arabin is almost identical with
that of its salts in gum.

The yield of furfuraldehyde by the breaking down of arabin and metarabin
was thought possibly to be of some value in differentiating the natural
gums from one another, but we have not succeeded in obtaining results of
much value. 0.2 gramme of a gum were heated with 100 c.c. of 15 per
cent. sulphuric acid for about 2½ hours in an Erlenmeyer flask with a
reflux condenser. After this period of time, further treating did not
increase the amount of furfuraldehyde produced. The acid liquid, which
was generally yellow in color, was then cooled and neutralized with
strong caustic soda. The neutral or very faintly alkaline solution was
then distilled almost to dryness, when practically the whole of the
furfuraldehyde comes over. The color produced by the gum distillate with
aniline acetate can now be compared with that obtained from some
standard substance treated similarly. The body we have taken as a
standard is the distillate from the same weight of cane sugar. The tint
obtained with the standard was then compared with that yielded by the
gum distillate from which the respective ratios of furfuraldehyde are
obtained. The following table shows some of these results:

    ---------------+--------------------+-----------------+
                   | Comparative Yield  |  Amount of      |
    Substance.     | of Furfuraldehyde. |Glucose Produced.|
    ---------------+--------------------+-----------------+
    Cane sugar     |     1.00           |      ..         |
    Starch         |     0.50           |      ..         |
    Gum arabic     |     1.33           |    34.72        |
    Gum arabic     |     1.20           |    43.65        |
    Ghatti, 1      |     1.00           |    26.78        |
    Ghatti, 2      |     1.33           |    22.86        |
    Metarabin      |     1.75           |      ..         |
    ---------------+--------------------+-----------------+

The amount of reducing sugar calculated as glucose is also appended.
This was estimated in the residue left in the flask after distillation
by Fehling's solution in the usual way. The yields of furfuraldehyde
would appear to have no definite relation to the other chemical data
about a gum, such as the potash and baryta absorptions or the sugar
produced on inversion.

The action of gum solutions upon polarized light is interesting,
especially in view of the fact that arabin is itself strongly
lævo-rotatory [alpha]_{D} = -99°, while certain gums are distinctly
dextro-rotatory. Hence it is evident that some other body besides arabin
is present in the gum. We have determined the rotatory power of a number
of gum solutions, the results of which are subjoined. On first
commencing the experiments we experienced great difficulty from the
nature of the solutions. Most of them are distinctly yellow in color and
almost opaque to light, even in dilute solutions such as 5 percent. We
found it necessary first to bleach the gums by a special process; 5
grammes of gum are dissolved in about 40 c.c. of lukewarm water, then a
drop of potassium permanganate is added, and the solution is heated on a
water bath with constant stirring until the permanganate is decomposed
and the solution becomes brown. A drop of sodium hydrogen sulphate is
now added to destroy excess of permanganate. At the same time the
solution becomes perfectly colorless.

It can now be cooled down and made up to 100 c.c., yielding a 5 per
cent. solution of which the rotatory power can be taken with ease. Using
a 20 mm. tube and white light the above numbers were obtained.

    ----------------+----------------+-----------------
    Gum or Dextrin. | Solution used. |    [alpha]_{D}
    ----------------+----------------+-----------------
                    |   Per Cent.    |
    Aden, 1         |       5        |     - 33.8
    Cape, 2         |       5        |     + 28.6
    Indian, 3       |       5        |     + 66.2
    Eastern, 4      |       5        |     - 26.0
    Eastern, 5      |       5        |     - 30.6
    Senegal, 6      |       5        |     - 17.6
    Senegal, 7      |       5        |     - 18.4
    Senegal, 8      |       2½       |     - 19.6
    Senegal, 9      |       5        |     - 38.2
    Senegal, 10     |       5        |     - 25.8
    Amrad           |       2½       |     + 57.6
    Australian, 1   |       5        |     - 28.2
    Australian, 2   |       5        |     - 26.4
    Brazilian, 1    |       2½       |     - 36.8
    Brazilian, 2    |       2½       |     + 21.0
    Dextrin, 1      |       5        |     +148.0
    Dextrin, 2      |       5        |     +133.2
    Ghatti, 1       |       5        |     - 39.2
    Ghatti, 2       |       5        |     - 80.4
    ----------------+----------------+-----------------

These numbers do not show any marked connection between the viscosity,
etc., of a gum and its specific rotatory power.

When gum arabic solution is treated with alcohol the gum is precipitated
entirely if a large excess of spirit be used. With a view to seeing if
the precipitate yielded by the partial precipitation of a gum solution
was identical in properties to the original gum, we examined several
such precipitates from various gums to ascertain their rotatory power.
We found in each case that the specific rotatory power of the alcohol
precipitate redissolved in water was not the same as that of the
original gum. In other words these gums contained at least two bodies of
different rotatory powers, of which one is more soluble in alcohol than
the other. O'Sullivan obtained similar results with pure arabin. The
experiments were conducted in the following manner:

(a.) Five grammes of a dextro-rotatory gum (No. 3 in table) were
dissolved in 20 c.c. of water. To the solution was added 90 c.c. of 95
per cent. alcohol. The white precipitate which formed was thrown on to a
tared filter and washed with 30 c.c. more alcohol. The total filtrate
therefore was 140 c.c. The precipitate was dried and weighed = 2.794
grammes or 55.88 per cent. of the total gum. The precipitate was then
redissolved in water, bleached as before and diluted to a 5 per cent.
solution. This was then examined in the polarimeter. Readings gave the
value [alpha]_{D} = +58.4°. The previous rotatory power of the gum was
+66°. Now the alcohol was driven off from the filtrate, which, allowing
for the 11.95 per cent. of water in the gum, should contain 32.17 per
cent. of gum. The alcohol-free liquid was then diluted to a known
volume (for 5 per cent, solution), and [alpha]_{J} found to be +57.7°.
This experiment was then repeated again, using 5 grammes of No. 3, when
3.5805 grammes of precipitate were obtained, using the same volumes of
alcohol and water. The precipitate gave [alpha]_{J} = +57.4°; the
filtrate treated as before, only the percentage of gum dissolved being
directly determined instead of being calculated by difference, gave
[alpha]_{J} = +52.5°.

(b.) Another gum (No. 9) with [alpha]_{J} = -38.2° and containing 13.86
per cent, of moisture, gave 2.3315 grms. of precipitate when similarly
treated. The precipitate gave when redissolved in water [alpha]_{J} =
-20.8°. The filtrate containing 39.5 per cent, real gum gave [alpha]_{J}
= -67.5°, so that the least lævo-rotatory gum. was precipitated by the
alcohol.

The Ghattis apparently are all lævo-rotatory, and give much less
alcoholic precipitates than the gum arabic. The precipitation moreover
was in the opposite direction, that is, the most lævo-rotatory gum was
thrown down by the alcohol. The appended table shows the nature of the
precipitates and the respective amounts from two Ghattis and two gum
arabics. It will be observed that the angle of rotation in three of the
cases is decidedly less both for precipitate and filtrate than for the
original solution:

SPECIFIC ROTATORY POWERS OF GUMS.

----------+------+--------+--------+-----------+------------+-----------+
Gum       |Weight| Weight | Weight |[alpha]_{J}|[alpha]_{J} |[alpha]_{J}|
used.     | Gum  | Alcohol|  Gum   | Original  |  Alcohol   | Filtrate. |
          |Waken.| Precip-|Filtrate|  Gum.     |Precipitate.|           |
          |      | itate. |        |           |            |           |
----------+------+--------+--------+-----------+------------+-----------+
          |      |  Grms. |        |           |            |           |
  /a......| 5    | 2.7940 | 1.9415 |           |    +58.4   |   +53.7   |
3{        |      |        |        |   +66.2   |            |           |
  \b......| 5    | 3.5805 | 0.8910 |           |    +57.4   |   -52.5   |
          |      |        |        |           |            |           |
  /a......| 5    | 2.3315 | 2.3736 |           |    -20.8   |   -67.5   |
9{        |      |        |        |   -38.2   |            |           |
  \b......|4.9620| 2.3310 | 2.4180 |           |    -19.4   |   -63.4   |
          |      |        |        |           |            |           |
       /a.|3.4900| 0.3925 | 2.7920 |           |   -104.2   |   -76.0   |
Ghatti{   |      |        |        |  -140.8   |            |           |
       \b.|3.2450| 0.4605 | 2.8385 |           |   -106.0   |   -72.4   |
          |      |        |        |           |            |           |
       /a.|2.2550| 0.2900 | 1.8078 |           |   -106.04  |   +68.0   |
Ghatti{   |      |        |        |  -147.05  |            |           |
       \b.|2.6635| 0.2845 | 2.3360 |           |   -102.04  |   -66.2   |
----------+------+--------+--------+-----------+------------+-----------+


The hygrometric nature of a gum or dextrin is a point of considerable
importance when the material is to be used for adhesive purposes. The
apparatus which we finally adopted after many trials for testing this
property consists simply of a tinplate box about 1 ft. square, with two
holes of 2 in. diameter bored in opposite sides. Through these holes is
passed a piece of wide glass tubing 18 in. long. This is fitted with
India rubber corks at each end, one single and the other double bored.
Through the double bored cork goes a glass tube to a Woulffe's bottle
containing warm water. A thermometer is passed into the interior of the
tube by the second hole. The other stopper is connected by glass tubing
to a pump, and thus draws warm air laden with moisture through the tube.
Papers gummed with the gums or dextrins, etc., to be tested are placed
in the tube and the warm moist air passed over them for varying periods,
and their proneness to become sticky noted from time to time. By this
means the gums can be classified in the order in which they succumbed to
the combined influences of heat and moisture. We find that in resisting
such influences any natural gum is better than a dextrin or a gum
substitute containing dextrin or gelatin. The Ghattis are especially
good in withstanding climatic changes.

Dextrins containing much starch are less hygroscopic than those which
are nearly free from it, as the same conditions which promote the
complete conversion of the starch into dextrin also favor the production
of sugars, and it is to these sugars probably that commercial dextrin
owes its hygroscopic nature. We have been in part able to confirm these
results by a series of tests of the same gums in India, but have not yet
obtained information as to their behavior in the early part of the year.

The fermentation of natural gum solutions is accompanied by a decrease
in the viscosity of the liquid and the separation of a portion of the
gum in lumps. Apparently those gums which contain most sugar, as
indicated by their reduction of Fehling's solution, are the most
susceptible to this change. Oxalic acid is formed by the fermentation,
which by combination with the lime present renders the fermenting liquid
turbid, and also some volatile acid, probably acetic.

We have made some experiments with a gum which readily fermented--in a
week--as to the respective value of various antiseptics in retarding the
fermentation. Portions of the gum solutions were mixed with small
quantities of menthol, thymol, salol, and saccharin in alkaline
solution, also with boric acid, sodium phosphate, and potash alum in
aqueous solution. Within a week a growth appeared in a portion to which
no antiseptic had been added; the others remained clear. After over five
months the solutions were again examined, when the following results
were observed:

----------------------+-------------------------------------------
                      |
    Antiseptics.      |       Solution after Five Months.
----------------------+-------------------------------------------
                      |
Menthol in KOH.....   | Some growth at bottom, upper layer clear.
                      |
Thymol in KOH.....    | Growth at top, gum white and opaque.
                      |
Salol in KOH........  | Growth at top, gum black and opaque
                      |
Saccharin in KOH ...  | White growth at top.
                      |
Boric acid............| Remained clear; did not smell.
                      |
Sodium phosphate ...  | Slight growth at top.
                      |
Potash alum.........  | Slight growth at top.
----------------------+-------------------------------------------

The solution to which no antiseptic had been added was of course quite
putrid, and gave the reactions for acetic acid.

In the earlier part of this paper we have given a short account of the
chief characteristics of the more important gum substitutes. The
following additional notes may be of interest.

The ashes of most gum substitutes, consisting chiefly of dextrin, are
characterized by the high percentage of chlorides they contain, due no
doubt to the use of hydrochloric acid in their preparation. The soluble
constituents of the ash consist of neutral alkaline salts, but as a rule
no alkaline carbonates, and it is thus possible to demonstrate the
absence of any natural gum in such a compound. We have seldom noticed
the presence of any sulphates in such ashes, but when sulphurous or
sulphuric acids have been used in the starch conversion it will be found
in small quantities.

We have already pointed out that the potash absorption value of a gum is
low and that dextrins give high numbers, but the latter vary very
considerably, and as the starch and sugar present also influence the
potash absorption value, it does not give information of much service.
The following table shows the kind of results obtained:

-----------------------------+----------+--------------+--------------
          Sample.            |   KOH    |   Starch.    | Real Gum.
                             | absorbed.|              |
-----------------------------+----------+--------------+--------------
                             |          |  Per Cent.   | Per Cent.
Dextrin, 1                   |  25.40   |     1.99     |    ..
Dextrin, 2                   |  19.70   |    13.13     |    ..
Dextrin, 3                   |   7.57   |    24.72     |    ..
Artificial gum, 1            |  19.70   |    10.98     |   9.00
Artificial gum, 2            |  13.70   |     8.05     |  23.50
Starch                       |   9.43   |   100.00     |   None
-----------------------------+----------+--------------+--------------

The baryta absorptions seem to be chiefly due to the quantity of starch
present in the composition:


----------------------------+---------------+-------------------------
           Sample.          |    Starch.    |       BaO
                            |               |      absorbed.
----------------------------+---------------|-------------------------
                            |   Per Cent.   |      Per Cent.
Dextrin, 1                  |      1.99     |        1.75
Dextrin, 2                  |     13.13     |        3.53
Dextrin, 3                  |     24.72     |        5.64
Starch                      |    100.00     |       23.61
----------------------------+---------------+-------------------------

The viscosity of a dextrin or artificial gum is determined in exactly
the same way as a natural gum, using 10 per cent. solutions. It would
probably be an improvement to use 10 per cent. solutions for many of the
dextrins, as they are when low in starch extremely thin.

The hygroscopic nature of dextrins renders them unsuitable for foreign
work, but when the quantity of starch is appreciable, better results are
obtainable. A large percentage of unaltered starch is usually
accompanied with a small percentage of sugar, and no doubt this is the
explanation of this fact. An admixture containing natural gum of course
behaved better than when no such gum is present. Bodies like "arabol"
made up with water and containing gelatin are very hygroscopic when dry,
although as sold they lose water on exposure to the air. Gum substitutes
consisting entirely of some form of gelatin with water, like fish glue,
are also somewhat hygroscopic when dried. The behavior of these
artificial gums and dextrins on exposure to a warm moist atmosphere can
be determined in the same apparatus as described for gums.

The process we have adopted for estimating the glucose starch and
dextrin in commercial gum substitutes is based on C. Hanofsky's method
for the assay of brewers' dextrins (this Journal, 8, 561). A weighed
quantity of the dextrin is dissolved in cold water, filtered from any
insoluble starch, and then the glucose determined directly in the clear
filtrate by Fehling's solution. The real dextrin is determined by
inverting a portion of the filtered liquid with HCl, and then
determining its reducing power. The starch is estimated by inverting a
portion of the solid dextrin, and determining the glucose formed by
Fehling. After deducting the amounts due to the original glucose and the
inverted dextrin present, the residue is calculated as starch. A
determination of the acidity of the solution is also made with decinormal
soda, and results returned in number of c.c. alkali required to
neutralize 100 grammes of the dextrin. Results we have obtained using
this method are embodied in the following table:

                    ANALYSIS OF GUM SUBSTITUTES

----+---------+---------+--------+----------+-------+-------+---------
 No.| Glucose.| Dextrin.| Starch.| Moisture.|  Gum, |  Ash. |Acidity.
    |         |         |        |          |   &c. |       |
----+---------+---------+--------+----------+-------+-------+---------
    |         |         |        |          |       |       |  cc.
  1 |   8.92  |  81.57  |   1.99 |  10.12   |  None | 0.207 |  57.3
  2 |   7.19  |  71.46  |  13.13 |  10.40   |  None | 0.120 |  44.8
  3 |   1.29  |  69.42  |  24.72 |   4.17   |  1.12 | 0.280 |  5.22
  4 |   8.40  |  60.98  |  10.98 |  10.09   |  9.02 | 0.530 |  20.0
  5 |  10.60  |  44.98  |   8.05 |  12.20   | 23.57 | 0.600 |  52.0
  6 |  14.80  |  11.57  |  36.46 |  34.87   |  1.89 | 0.580 |   8.0
  7 |   8.00  |  29.61  |  26.78 |  33.98   |  0.88 | 0.750 |  88.0
  8 |   2.29  |  52.38  |  37.65 |  None    | 7.335 | 0.315 |   9.6
----+---------+---------+--------+----------+-------+-------+---------

In those cases in which the substitute is made by admixture with gelatin
or liquid glue the quantity of other organic matter obtained can be
checked by a Kjeldahl determination of the total nitrogen. If a natural
gum is added, it will be partially converted into sugar when the
filtered liquid is inverted, and so make the dextrin determination
slightly too high.

       *       *       *       *       *




MR. CAILLETET'S CRYOGEN.


The "cryogen," a new apparatus constructed by Mr. E. Ducretet, from
instructions given by Mr. Cailletet, is designed for effecting a fall of
temperature of from 70° to 80° C. below zero, through the expansion of
liquid carbonic acid.

The apparatus consists of two concentric vessels having an annular space
between them of a few centimeters. A worm, S, is placed in the internal
vessel R. All this is of nickel plated copper. The worm, S carries, at
Ro', an expansion cock and ends, at O in the annular space, R'. A very
strong tube is fixed to the cock, Ro', and to the ajutage, A'. It
receives the tube, Tu, which, at the time of an experiment, is coupled
with the cylinder of carbonic acid, CO². A tubulure, D, usually closed
by a plug, Bo, communicates with the inner receptacle, R. This is
capable of serving in certain experiments in condensation. The table,
Ta, of the tripod receives the various vessels or bottles for the
condensed products.

The entire apparatus is placed in a box, B, lined with silk waste and
provided with a cover, C, of the same structure. Apertures, Th, Ro, and
T", allow of the passage of a key for acting upon the cock, Ro', as well
as of thermometers and stirrers if they are necessary.

When it is desired to operate, the internal vessel, R, is filled with
alcohol (3 quarts for the ordinary model). This serves as a refrigerant
bath for the experiments to be made. The worm, S, having been put in
communication with the carbonic acid cylinder, CO², the cock, Ro, of the
latter is turned full on. The cock of the worm, which is closed, is
opened slightly. The vaporization and expansion of the liquid carbonic
acid cause it to congeal in the form of snow, which distributes itself
and circulates in the worm, S, and then in R. The flakes thus coming in
contact with the metallic sides of S rapidly return to the gaseous state
and produce an energetic refrigeration. At the lower part of the annular
space, R', are placed fragments of sponge impregnated with alcohol. The
snow that has traversed the worm without vaporizing reaches R'. and
dissolves in this alcohol, and the refrigeration that results therefrom
completes the lowering of the temperature. The gas finally escapes at O,
and then through the bent tube, T".

[Illustration: CAILLETET'S CRYOGEN.]

The apparatus may be constructed with an inverse circulation, the
carbonic acid then entering the annular vessel, R, directly, and
afterward the worm, S, whence it escapes to the exterior of the
apparatus. The expansion cock sometimes becomes obstructed by the
solidification of the snow. It will then suffice to wait until the
circulation becomes re-established of itself. It may be brought about by
giving the cock, Ro', a few turns with the wooden handled key that
serves to maneuver the latter. It is not necessary to have a large
discharge of carbonic acid, and consequently the expansion cock needs to
be opened but a little bit. A few minutes suffice to reduce the
temperature of the alcohol bath to 70°, with an output of about from 4½
to 5½ lb. of liquid carbonic acid. When the circulation is arrested, the
apparatus thus surrounded by its isolating protective jackets becomes
heated again with extreme slowness. In one experiment, it was observed
that at the end of nine hours the temperature of the alcohol had risen
but from 70° to 22°. On injecting a very small quantity of liquid
carbonic acid from time to time, a sensibly constant and extremely low
temperature may be maintained indefinitely.--_Le Genie Civil_.

       *       *       *       *       *




METHOD OF PRODUCING ALCOHOL.


In carrying out my improved process in and with the apparatus employed
in ordinary commercial distilleries, says Mr. Alfred Springer, of
Cincinnati, O., I preferably employ separate vats or tubs for the nitric
acid solution and the material to be treated, and a convenient
arrangement is to locate the nitric acid tub directly under the grain
tub, so that one may discharge into the other. In the upper vat is
placed the farinaceous material, preferably ground, thoroughly steeped
in three times its weight of water, and, where whole grain is used,
preferably "cooked" in the ordinary manner. The vat into which the
dilute acid is placed is an ordinary cooking tub of suitable material to
resist the acid, provided with closed steam coils and also nozzles for
the discharge of steam into the contained mass. Into this vat is placed
for each one hundred parts of the grain to be treated one part of
commercial nitric acid diluted with fifty parts of water and brought to
a state of ebullition and agitation by the steam coils and the discharge
through the nozzles, the latter being regulated so that the gain by
condensation of steam approximately equals the loss by evaporation. The
farinaceous contents of the upper vat are allowed to flow slowly into
the nitric acid solution while the ebullition and agitation of the mass
is continued. This condition is then maintained for six to eight hours,
after which the mass is allowed to stand for one day or until the
saccharification becomes complete. The conversion can be followed by the
"iodine test" for intermediary dextrins and the "alcohol test" for
dextrin. After the saccharification is complete I may partially or
wholly neutralize the nitric acid, preferably with potassium or Ammonium
carbonate, preferably employing only one-half the amount necessary to
neutralize the original quantity of nitric acid used, so that the mass
now ready to undergo fermentation has an acid reaction. The purpose in
view here is to keep the peptones in solution also, because an acid
medium is best adapted to the propagation of the yeast cells. It is not
absolutely necessary to even partially neutralize the nitric acid, but
it is preferable. Yeast is now added, and the remaining processes are
similar to those generally employed in distilleries, excepting that just
prior to distillation potassium carbonate sufficient to neutralize the
remaining nitric acid is added, in order to avoid corrosion of the still
and correct the acid reaction of the slop.

As a variant of the process I sometimes add to the usual amount of
nitric acid an additional one one-hundredth part of phosphoric acid on
account of its beneficial nutritive powers--that is to say, to one
hundred parts of grain one part of nitric acid and one one-hundredth
part of phosphoric acid.

While my improved process is based on the well-known converting power of
acids on starch, I am not aware that it has ever been applied in the
manner and for the purposes I have described. For example, sulphuric and
hydrochloric, also sulphuric and nitric, acids have been employed in the
manufacture of glucose; but in every such case the resulting products
were not capable of superseding those obtained by the existing methods
of saccharification used in distilleries. In my process, on the other
hand, the product is so capable. Not only may malted grain be entirely
omitted, but more fermentable products are formed and the products of
fermentation are purer. The saccharification being more complete, there
are less intermediary and nonfermentable dextrins, and the yield of
spirits is therefore increased. Malted grain being omitted or used in
reduced quantity, there is less lactic acid and few or foreign ferments
to contaminate the fermenting mass; also, the formation of higher
alcohols than the ethyl alcohol is almost totally suppressed.
Consequently the final yield of spirits is purer in quality and requires
little or no further purification. Also, further, the nitrates
themselves acting as nutrients to the yeast cells, these become more
active and require less nutrition to be taken from the grain.

       *       *       *       *       *




SPECTROSCOPIC DETERMINATION OF THE SENSITIVENESS OF DRY PLATES.


After describing other methods of determining the sensitiveness of
plates, Mr. G.F. Williams, in the _Br. Jour. of Photo_., thus explains
his plan. I will now explain the method I adopt to ascertain the
relative sensitiveness of plates to daylight. Procure a small direct
vision pocket spectroscope, having adjustable slit and sliding focus. To
the front of any ordinary camera that will extend to sixteen or eighteen
inches, fit a temporary front of soft pine half an inch thick, and in
the center of this bore neatly with a center bit a hole of such diameter
as will take the eye end of the spectroscope; unscrew the eyehole, and
push the tube into the hole in wood, bushing the hole, if necessary,
with a strip of black velvet glued in to make a tight fit. By fixing the
smaller tube in the front of camera we can focus by sliding the outer
tube thereon; if we fix the larger tube in the front, we should have to
focus inside the camera, obviously most inconvenient in practice. Place
the front carrying the spectroscope _in situ_ in the camera, and rack
the latter out to its full extent; point the camera toward a bright sky,
or the sun itself, if you can, while you endeavor to get a good focus.
The spectrum will be seen on the ground glass, probably equal in
dimensions to that of a quarter plate. Proceed to focus by sliding the
outer tube to and fro until the colors are quite clear and distinct, and
at same time screw down the slit until the Fraunhofer lines appear. By
using the direct rays of the sun, and focusing carefully, and adjusting
the slit to the correct width, the lines can be got fairly sharply.
Slide your front so that the spectrum falls on the ground glass in just
such a position as a quarter plate glass would occupy when in the dark
slide, and arrange matters so that the red comes to your left, and the
violet to the right, and invariably adopt that plan. It is advisable to
include the double H lines in the violet on the right hand edge of your
plate. They afford an unerring point from which you can calculate
backward, finding G, F, E, etc., by their relative positions to the
violet lines. Otherwise you may be mistaken as to what portion of the
spectrum you are really photographing. The red should just be seen along
the left edge of the quarter plate. When all is arranged thus, you
utilize three-fourths of your plate with the spectrum, with just a
little clear glass at each end. Before disturbing the arrangement of
the apparatus, it is desirable to scratch a mark on the sliding tube,
and make a memorandum of the position of all the parts, so that they may
be taken away and replaced exactly and thus save time in future.

To take a photograph of the spectrum, put a quarter plate in the dark
slide and place in camera; point the camera toward a bright sky, or
white cloud, near the sun--not at the sun, as there is considerable
difficulty in keeping the direct rays exactly in the axis of the
spectroscope--draw the shutter, and give, say, sixty seconds. On
development, you will probably obtain a good spectrum at the first
trial. The duration of exposure must, of course, depend upon the
brightness of the day; but if the experiments are to have relative
values, the period of exposure must be distinctly noted, and comparisons
made for a normal exposure of sixty seconds, ninety seconds, two minutes
or more, just according to whatever object one has in view in making the
experiments. With a given exposure the results will vary with the light
and the width of the slit, as well as being influenced by the character
of the instrument itself. Further, all such experiments should be made
with a normal developer, and development continued for a definite time.
The only exception to this rule would be in the event of wishing to
ascertain the utmost that could be got out of a plate, but, under
ordinary circumstances, the developer ought never to vary, nor yet the
duration of development. To try the effect of various developers, or
varying time in development, a departure must be made of such a nature
as would operate to bring out upon each plate, or piece of a plate, the
utmost it would develop short of fog, against which caution must be
adopted in all spectrum experiments.

On development, say for one, two, or three minutes, wash off and fix.
You will recognize the H violet lines and the others to the left, and
this experiment shows what is the sensitiveness of this particular plate
to the various regions of the spectrum with this particular apparatus,
and with a normal exposure and development. So far, this teaches very
little; it merely indicates that this particular plate is sensitive or
insensitive to certain rays of colored light. To make this teaching of
any value, we must institute comparisons. Accordingly, instead of simply
exposing one plate, suppose we cut a strip from two, three, four, or
even half a dozen different plates, and arrange them side by side,
horizontally, in the dark slide, so that the spectrum falls upon the
whole when they are placed in the camera and exposed. There is really no
difficulty in cutting strips a quarter of an inch wide, the lengthway of
a quarter plate. Lay the gelatine plate film up, and hold a straight
edge on it firmly, so that when we use a suitable diamond we can plow
through the film and cut a strip which will break off easily between the
thumb and finger. A quarter plate can thus be cut up into strips to
yield about a dozen comparative experiments. When cut and snapped off,
mark each with pencil with such a distinguishing mark as shall be
clearly seen after fixing. The cut up strips can be kept in the maker's
plate box.

       *       *       *       *       *


The deep down underground electric railway in London has so far proved
an unprofitable concern for its stockholders. It is 3½ miles long,
touches some of the greatest points of traffic, but somehow or other
people won't patronize it. The total receipts for the last six months
were a little under $100,000, and they only carried seventeen persons
per train mile. On this road the passengers are carried on elevators up
and down from the street level to the cars. The poor results so far make
the stockholders sick of the project of extending the road.

       *       *       *       *       *


A NEW CATALOGUE OF VALUE


Contained in Scientific American Supplement during the past ten years,
sent _free of charge_ to any address. Munn & Co., 361 Broadway, New
York.

       *       *       *       *       *


THE SCIENTIFIC AMERICAN

ARCHITECTS AND BUILDERS EDITION


$2.50 a Year. Single Copies, 25 cts.

This is a Special Edition of the Scientific American, issued monthly--on
the first day of the month. Each number contains about forty large
quarto pages, equal to about two hundred ordinary book pages, forming,
practically, a large and splendid Magazine of Architecture, richly
adorned with _elegant plates in colors_ and with fine engravings,
illustrating the most interesting examples of modern Architectural
Construction and allied subjects.

A special feature is the presentation in each number of a variety of the
latest and best plans for private residences, city and country,
including those of very moderate cost as well as the more expensive.
Drawings in perspective and in color are given, together with full
Plans, Specifications, Costs, Bills of Estimate, and Sheets of Details.

No other building paper contains so many plans, details, and
specifications regularly presented as the Scientific American. Hundreds
of dwellings have already been erected on the various plans we have
issued during the past year, and many others are in process of
construction.

Architects, Builders, and Owners will find this work valuable in
furnishing fresh and useful suggestions. All who contemplate building or
improving homes, or erecting structures of any kind, have before them in
this work an almost _endless series of the latest and best examples_
from which to make selections, thus saving time and money.

Many other subjects, including Sewerage, Piping, Lighting, Warming,
Ventilating, Decorating, Laying out of Grounds, etc., are illustrated.
An extensive Compendium of Manufacturers' Announcements is also given,
in which the most reliable and approved Building Materials, Goods,
Machines, Tools, and Appliances are described and illustrated, with
addresses of the makers, etc.

The fullness, richness, cheapness, and convenience of this work have won
for it the Largest Circulation of any Architectural publication in the
world.

A Catalogue of valuable books on Architecture, Building, Carpentry,
Masonry, Heating, Warming, Lighting, Ventilation, and all branches of
industry pertaining to the art of Building, is supplied free of charge,
sent to any address.

MUNN & CO., PUBLISHERS, 361 BROADWAY, NEW YORK.

       *       *       *       *       *


BUILDING PLANS AND SPECIFICATIONS.


In connection with the publication of the Building; EDITION of the
Scientific American, Messrs, Munn; & Co. furnish plans and
specifications for buildings' of every kind, including Churches,
Schools, Stores, Dwellings, Carriage Houses, Barns, etc.

In this work they are assisted by able and experienced architects. Full
plans, details, and specifications for the various buildings illustrated
in this paper can be supplied.

Those who contemplate building, or who wish to alter, improve, extend,
or add to existing buildings, I whether wings, porches, bay windows, or
attic rooms, fare invited to communicate with the undersigned. Our work
extends to all parts of the country. Estimates, plans, and drawings
promptly prepared. Terms moderate. Address

MUNN & CO., 361 BROADWAY, NEW YORK.

       *       *       *       *       *


THE SCIENTIFIC AMERICAN SUPPLEMENT.


Published Weekly. Terms of Subscription, $5 a year.

Sent by mail, postage prepaid, to subscribers in any part of the United
States or Canada. Six dollars a year, sent, prepaid, to any foreign
country.

All the back numbers of The Supplement, from the commencement. January
I, 1876, can be had. Price, 10 cents each.

All the back volumes of The Supplement can likewise be supplied. Two
volumes are issued yearly. Price of each volume, $2.50 stitched in
paper, or $3.50 bound in stiff covers.

Combined Rates.--One copy of Scientific American and one copy of
Scientific American Supplement, one year, postpaid, $7.00.

A liberal discount to booksellers, news agents, and canvassers.

MUNN & CO., PUBLISHERS,

361 BROADWAY, NEW YORK, N.Y.

       *       *       *       *       *


USEFUL ENGINEERING BOOKS


Manufacturers, Agriculturists, Chemists, Engineers, Mechanics, Builders,
men of leisure, and professional men, of all classes, need good books in
the line of their respective callings. Our post office department
permits the transmission of books through the mails at very small cost.
A comprehensive catalogue of useful books by different authors, on more
than fifty different subjects, has recently been published, for free
circulation, at the office of this paper. Subjects classified with names
of author. Persons desiring a copy have only to ask for it, and it will
be mailed to them. Address,

MUNN & CO., 361 BROADWAY, NEW YORK.

       *       *       *       *       *




PATENTS!


Messrs. Munn & Co., in connection with the publication of the Scientific
American, continue to examine improvements, and to act as Solicitors of
Patents for Inventors.

In this line of business they have had _forty-five years experience_,
and now have _unequaled facilities_ for the preparation of Patent
Drawings, Specifications, and the prosecution of Applications for
Patents in the United States, Canada, and Foreign Countries. Messrs.
Munn & Co. also attend to the preparation of Caveats, Copyrights for
Books, Labels, Reissues, Assignments, and Reports on Infringements of
Patents. All business intrusted to them is done with special care and
promptness, on very reasonable terms.

A pamphlet sent free of charge, on application, containing full
information about Patents and how to procure them; directions concerning
Labels, Copyrights, Designs, Patents, Appeals, Reissues, Infringements,
Assignments, Rejected Cases. Hints on the Sale of Patents, etc.

We also send, _free of charge_, a Synopsis of Foreign Patent Laws,
showing the cost and method of securing patents in all the principal
countries of the world.

MUNN & CO., SOLICITORS OF PATENTS, 361 Broadway, New York.

Branch Offices.--Nos. 622 and 624 F Street, Pacific Building, near 7th
Street, Washington, D.C.